i m trying to connect two routers a Cisco DPC3825 (r1) and DIR-655 (r2) and at the end getting the error. i have disabled the SPI firewall on r1 and connected an ethernet cable lan to lan between the two. i don't want to confuse with whatever the mess i have done previously,Tell step by step what i should do to connect these two routers.PS: in addition, the gateway ip of r1 is 192.168.0.1 with subnet mask of 255.255.254.0 and the gateway ip of r2 is 192.168.0.2 with subnet mask of 255.255.255.0. r1 has a ip range of 192.168.0.10 to 192.168.0.128 while r2 has range of 192.168.0.100 to 192.168.0.199.
Trying to connect two systems together but was giving error that contact network administrator,one system is laptop with wireless and other is desktop but connect through cable but running windows XPSamson
I bought belkin N150 recently. I tried to configure with my ISP. They are surprised how I don't have DHCP option in the wifi configuration and asked me to upgrade my firmware. When I tried to upgrade. I downloaded the firmware from [URL] tried to upgrade. It is showing file format error.
Up to today I used Verizoon 4G to a Windows Visata box running Internet connection Sharing to get my home lab connected to the Internet . All was working well.
Today I had Hughesnet come and installl their service and I can no longer get access to the Internet from my PC netowrk. my VPN to my office for my IP phone coomes up an works just fine. At the router I do have Internet access which then leads me to believe that my problem is NAT related.
My router is a 2851.
When I enter PING 4.2.2.2 I get !!!!! but when i enter PING 4.2.2.2 SOURCE 192.168.69.3 I get .....
I had been working on our client servers through Cisco VPN using internet datacard. But from past 3 weeks after logging into Cisco VPN using my username/password, when I try to connect to any of the servers, it is giving connection timed out error.
Whereas, my team members across other locations are able to connect to the servers using my VPN username/password.
I thought there might be some issue with my laptop or internet datacard. I got my laptop formatted, even tried out with fresh new laptops & new internet datacards, but the issue remains same.
I have tried using vpn_5.0.06.0160-k9 & vpnclient-5.0.05.0290-k9 to connect but issue did not get resolved.
After a successfull installation of NCS 1.2 into a vmware environment and run the setup I have the following error while trying to start or to have a status for NCS (ncs start ot ncs status):sh: /opt/CSCOlumos/bin/wcsadmin.sh No such file or directory
I have a WiFi printer connected to an CWAPP Cisco AP AP1250. I am using WPA2-PSK to connect to this AP. I find that the printer connects to the AP at times and at times it does not. I got an error message from the Capture an error on the backend controller of the network."Authentication Request received invalid RSN IE Mismatch WP2 algorithm"
The problem is that one of the clients loses the connection to the network time to time ,The error in the WLC logg is
*Dot1x_NW_MsgTask_0: Jul 06 17:42:38.934: %DOT1X-3-INVALID_WPA_KEY_MSG_STATE: 1x_eapkey.c:843 Received EAPOL-key M2 msg has invalid information when mobile is in START state - invalid secure bit; KeyLen 24, Key type 1, client 00:21:6a:af:be:70
I am currently on Time Warner Cable 10 mbps packge, and am using their wireless DOCIS3 modem/router. It is connected in my bedroom to the main computer. That computer stays connected. However, throughout the rest of the house (we have a two story townhome) it will drop completely or give limited connection...constantly. Sometimes I can have my laptop next to me and it will go out or give limited connection. The connection speed never drops, it just goes completely to no connection. Not for sure what is going on, if its on my end or time warner. Has been doing this for quite some time, the cable company comes out and changes the modem, but that's it, couple days later, goes back to doing it again.
I have an 1841 that was working fine - I could SSH to it with my Radius login and console into it with local credentials ("Fred").I added another use ("Mike") with priv 15 so the end user could log in locally via console if needed.After that, we can both log in via console, but when we try to enter privileged mode we get "% Error in Authentication", before even entering the password.I can still log in via Radius SSH with no problems and access privilege mode via SSH.What am I missing so we can have two different users be able to log in locally with different credentials and access privileged mode, and keep my ssh radius working?
We're seeing "OutDiscard" error on a LAN switch connected to newly migrated Cisco IP phones. All the other error counters are clean except for the OutDiscard. (please see attached "show int count err" output.) [URL].
According to the link above, the common cause of such discards can be to free up buffer space.(Am I seeing a switch buffer issue?) How to identify/resolve the cause of the OutDiscard.The switch is 3750-E running c3750e-universalk9-mz.122-44.SE6.bin
I was using my internet on my Acer Windows 7 operating system wireless just fine on Monday. I tried to use it on Tuesday and could not connect to the internet wireless any longer. I get an error message next to my network stating ""The settings [COLOR=green ! important][COLOR=green ! important]saved[/COLOR][/COLOR] on this computer do not match the requirements of the network"I have never encotured this kind of problem before. I proceeded to call Comcast who did all kinds of trivial beginner troubleshooting such as restart the router, restart the modem turn on and off the computer.
I 've got some problem with my Mail Server since I've migrated to an ASA5510.Actually the server is in a DMZ with a private Ip ( 10.x.x.2) and it is translated to a Public IP ( 194.x.x.65).Some Users received in there mailbox a system administor error message :Object : Impossible to deliver : testYour message could not be deliver to one or more of its recipients: 421 SMTP connection went away!When they try to re sent it some times later, message is sent whithout problem.
I have 2 datacenters running same equipement (two Nexu 5596 with FEX).I just took a look at the log just to see if everything is ok and I saw that I have the same error message (a lot of times) at both location :
%SYSMGR-FEX100-5-HEARTBEAT_LOSS: Service "satctrl" heartbeat loss 2 ,max 7,I though it was a problem with my peerklink-keepalive connection but I see the word FEX ....so i'm not sure...
Note that at both locations, my Nexus are connected back to back through the management port using transceivers. So it's a copper cable from the first nexus, going into a transceiver, going to another transceiver in fiber and then back to copper to the other nexus.
Just bought first wireless router, when i insert CD and start setup, after a few seconds i get Error 301: internal error. i have rebooted and still no luck. I've tried going to 192.168.1.1, i got in one time but didn't understand half the stuff. now i can't go back into that page.
We find ourselves in a difficult situation with the Cisco VPN Client version 5.0.07.0290 where it keeps giving us an
"Error 42: Unable to create certificate enrollment request"
When we attempt to use the Online enrollment method to create and enroll a new certificate. There is no additional information in the VPN client logs where we have set 3-High for all logs. In addition, Wire shark does not show any packets sent from the machine running the client to the Cisco 3825 router which runs the Cisco CA.
To create and enroll a certificate we do the following:
1. Click on the Enroll button to show the Certificate Enrollment dialog 2. Select Online 3. Select <New> for Certificate Authority 4. Enter http://192.168.120.1 as CA URL (note, 192.168.120.1 is the IP of the Cisco 3825) 5. Click Next to display the dialog where we can enter certificate details 6. Enter details in all fields except IP Address and Domain 7. Click Enroll which shows a dialog with the Error 42 ... message in it.
If we attempt to create a request by using the File method, all works fine, that is, the client creates a file with the enrollment request. The fact that the client does not send any messages to the Cisco CA leads us to believe that we have a problem on the client machine. However, the client does not write any information in the logs, so it is a bit hard to fix the problem. I can provide additional configuration information if required for both the client and the Cisco CA. Note that we have not modified any client configuration. Basically, we installed the client on a Windows 7 64bit machine and attempted the steps listed above.
I have tried Intel tools and latest drivers ( w/ and w/o pro wireless utility) but cannot pass thru code 10 error. Tried uninstall and install....as earlier card 4965 agn worked fine but seems like some conflict is stopping successful 5300 agn driver install.
tried 2 routers, one brand new , both DIR655 from Dlink - an older router. Just got a Comcast internet connection. The internet is fine when connected to the laptop directly. The router can talk to the computer. but plugging the internet cable into the router, the router never quite finds it, ie the blue indicator light never indicates access from modem to the router. So cant get that extra protection from the router, or the convenience of it.
By the way I am doing all of this hardwired even though the router is wireless capable. I did a hard reset which I could log on and see worked of the router. This happens when it is not hooked to the computer. I did the thing of powercycling modem and router, no change. Do I need a newer router? Is there something weird about Comcast, these were fine w Cablevision. Comcast tech support was useless.
RV042 router is giving out the outer certificate instead of server certificate. Outlook anywhere is failing and we are receiving certificate errors for any secure site behind this firewall. I'm not talking about remote management. I'm talking about people trying to access our web site, which is secured, and getting an error because the RV042 is giving its own SSL certificate instead of the Server's certificate. Firmware Version: 1.3.13.02-tm. I don't see any updates for that hardware. I do have it working on an RV042 with the same firmware at a different location. How do we turn that off or keep it from happening? Output from a test site Attempting to resolve the host name xxxx in DNS.The host name resolved successfully. Additional DetailsTesting TCP port 443 on host xxxx to ensure it's listening and open. The port was opened successfully. Testing the SSL certificate to make sure it's valid. The SSL certificate failed one or more certificate validation checks. Test Steps ExRCA is attempting to obtain the SSL certificate from remote server xxxx on port 443. ExRCA successfully obtained the remote SSL certificate. Additional Details Remote Certificate Subject:
SN=California, L=Irvine, C=US, O="Cisco-Linksys, LLC", OU=RV042, CN=68:ef:bd:b8:0f:78, Issuer: SN=California, L=Irvine, C=US, O="Cisco-Linksys, LLC", OU=RV042, CN=68:ef:bd:b8:0f:78.Validating the certificate name. Certificate name validation failed. Tell me more about this issue and how to resolve it Additional Details Host name xxxx doesn't match any name found on the server certificate SN=California, L=Irvine, C=US, O="Cisco-Linksys, LLC", OU=RV042, CN=68:ef:bd:b8:0f:78.
getting my computer connected to the internet.I have a fresh install of XP Media Center Edition with SP2. I don't really have anything else installed as I wanted to make sure my internet connection was working to get updates. My computer is a Dell XPS720 desktop I have a DSL connection with [URL] and a Dlink Wireless Router DIR655.I have two portable computers that are on the local network with wireless connections and they are working o.k.On my desktop at the command prompt; I cannot "ping" anything and "ipconfig /all" returns nothing at all.
Just installed RV042 router. And it's giving out router certificate instead of server certificate so people who are trying to access our secured server are getting errors. I'm not talking about remote management. I'm talking about people trying to access our web site, which is secured, and getting an error because the RV042 is giving its own SSL certificate instead of the Server's certificate. How do we turn that off or keep it from happenning?
The RV042 firm version is v4.0.0.07-tm (Aug 19 2010 19:19:50)
I have a RV042 router. The problem that I am having with it is that the DHCP is giving out the wrong Default Gateway and DNS Server. There is no option to change the DHCP server IP on any of the settings pages on the router. I am begining to think that there might not be a way to do it. I see that there is an option for the DNS under the DHCP page but the Public IP that is being handed out is not the one on that page. I also have 2 WAN connections hooked up as well a DSL link and a Cable link (the cable link is the primary one).
The following information is provided in an effort to resolve this issue: IP of Router 10.0.0.2 IP of DHCP Server (the one that is being handed out):10.0.0.1 IP of DNS (the one that is being handed out): 10.0.0.11
What I want to it be. IP of Router: 10.0.0.2 IP of DHCP 10.0.0.2 IP of DNS 10.0.0.2
I think there is a bug in the DPC3825.I use UPnP media servers and renderers in my home network.For some reason both the client and server have to be on the same side of the wireless / wired bridge.If the client is on the wireless side then the server also has to be on the wireless side.If the client is on the wired side then the server has to be on the wired side.Having a bit of knowledeg of the UPnP protocol I suspect that UDP broadcasts are not traversing the wired / wireless bridge.thus breaking the SSDP protocol that is used by UPnP and DNLA systems.I have no control over the product that my ISP uses and they seem to have no control over what Cisco does with its 'issues'.
I got a new modem today (a Cisco DPC3825) and it seems to be presenting a problem. I used to be able to simply and quickly change my IP address, by changing the MAC address though my Netgear router. Now when I do that, I can see the IP address has changed in the router settings, but when I double check it using ipburger.com, the IP address does NOT actually change, but remains the same.
I recently upgraded, through my ISP, my high-speed modem to the DPC3825 model modem/router. But when I try to connect to the DLink switch, the modem freezes, and doesn't recognize it. My previous setup was modem, to my DLink router (DIR 615), to my switch. With my new setup, I just bypassed the DLink router, because my new modem includes router capability.Is there some compatibility issue between the new modem and the DLink switch?
I have a DPC3825 from Shaw Cable in Canada. I'd like to use my Airport Extreme as a repeater using WDS. I've clicked the checkbox for "Allow wireless signal to be repeated by a repeater" and entered my Airport's MAC Address, but my Airport Base station doesn't see it as a WDS Peer.
Just got a Cisco DPC3825 from my ISP. I need to connect my other desktops to the wireless router all over the house and have two questions.
1. What is the best wireless adapter to use so my other desktops will be able to access the router?
2. What is the distance of signal before I need a signal booster and if I do need to boos the signal, what is the best device to do that? (we stream video, music, light gaming and general internet applications).
I am trying to figure out whyt my DPC3825 does not maintain a FTP session I did not really want to post this message rather I am trying to figure out how to search this board.
NIB DPC3825 cable modem. Called my provider and got it provisioned and its working (I'm on an ethernet connection posting this). But when I http to 192.168.0.1, I get a screen that doesn't quite look like the one in the manual. I enter the "admin" and "W2402" and click login, and the screen refreshes but nothing happens (no configuration options, only able to check status of downstream and upstream channels). Pushing the factory reset button for ten seconds to load defaults makes the lights blink and then reboots; same result as above. Pushing the wireless config button has no effect at all.
I got a problem with my router CISCO (DPC3825) where the eithernet is working properly and the wireless is not, and I had to plug the usb to make the setups, and suddenly the wireless was working but when I tried to reset the password something worng happened change the set of the wireles
I would like to know what ip addresses I should see in this table. Shouldn't my default gateway IP have the same mac address as my computer or router? There are 2 different ip address/mac addresses from different a ISP than mine. I have a cisco DPC3825..I suspect a someone is spoofing my DNS.
