Cisco Routers :: SRP521 Giving Busy Tone On Outbound?

Dec 13, 2012

I have a 521 with 1.01.24 The fxs port is registered and inbound calls work.  When the customer picks up the phone to make a call they get a busy tone.

View 1 Replies


ADVERTISEMENT

Cisco Routers :: Srp521 Change To Vpn Server?

Nov 13, 2012

I have a srp521 and want to set it up as a vpn server so I can connect back from outside.On the router under the vpn tab I only have
 
Site to site IPSec VPN
IKE Policy
IPSecPolicy
GRETunnel
VPN Passthrough
  
Page 191 of the srp500 manual says Click VPN > Cisco VPN Server > Group. The Group window opens The manual also says only the serer or Site to site will work at one time, so where do I make the change to bring up the vpn server option?

View 1 Replies View Related

Cisco Routers :: SRP521 DSCP Marking On QoS?

Jun 14, 2012

I am running 1.1.24 and spa303 phones I have a qos policy setup to mark all packets                  
 
The following is my qos

information 192.168.1.15/24
makring enabled
cos/DSCO DSCO
Value 0xb8
 
On my upstream device I only allow traffic that is marked with this dscp value.  No traffic is coming through.  RTP traffic is marked because it comes off the phone marked but I would expect the qos Policy so mark everything going to that ip space to be marked.

View 1 Replies View Related

Cisco Routers :: Srp521 Port Forward Based On Source Ip

Dec 20, 2012

I have a customer with a Sonic wall that I want to replace with a 521.He currently has port forwaring setup so that only 3 ip addresses can access the port forward.  Everyone else is dropped.  Is there a way to do something similar?I can make it work for a single one via the DMZ tab with a source ip address. but there is not a way I can find to add the allow for the other two remote connections.

View 1 Replies View Related

Cisco Routers :: Outbound Nating With RV082?

Jan 9, 2012

I just migrated our office network router to a RV082. While configuring it, I came across three problems: 
 
(1) From our ISP we have four public IP addresses which I want to make use of for outbound traffic. With the previous router we used we could configure LAN IPs(ranges) to map to static public IPs. Does RV082 support this? I could not find an option for that at the web-interface. From what I understand the 1-1 NATing only goes both incoming and outgoign ways and actually is 1-1 and not the many-to-one I am looking for.
 
(2) How is it possible to configure incoming port forwards to use a specific WAN interface? Will it always be the primary WAN interface?
 
(3) Does the telnet access provide more configuration options? I could not log in to it with the same user credentials as with the web-interface.
 
Serial Number : NKS1532xxxxFirmware Version : v4.0.4.02-tm (Jul 4 2011 13:30:56)PID VID : RV082 V03Firmware MD5 Checksum : 1f84d8d0a2a8b99f9bfa4409e64547aaLANWorking Mode : Gateway

View 0 Replies View Related

Cisco Routers :: Default Outbound Policy In RV220W

Aug 1, 2012

How to set the default outbound policy as block in access rules of rv220w? I configure my company router RV220W to block all outbound service traffic, just allow outbound service as : http, https, smtp, dns_tcp / udp. it works fine for some hours, the next day, the rules like expired, the https / smtp / DNS service fail to outgoing, only the http is still ok? What happen? Now I just set the default outbound policy as allow, all traffic can go out, but that is meaningless for a firewall device.

View 1 Replies View Related

Cisco Routers :: RV180W - Outbound Public IP Address?

Mar 26, 2013

What I'm trying to do seems pretty basic, but I cannot get it working on the RV180?I have 5 Fixed IPs. Using Access Rules I have configured a few inbound rules with specified WAN Destination addresses and these are correctly port forwarding these inbound ports on the specified Public IP addresses. Perfect!
 
However, for outbound, I need to do the equivalent for one public IP for outgoing SMTP so that our mail servers public facing address is not the standard WAN address and therefore will not fail a reverse DNS lookup. At the moment I have emails bouncing all over the place and panic has set in. I thought the SNAT option was the soltuion, but that just seems to break traffic flow completely on the specified port. I had this working no problem on my old Netgear, but I had to replace it due to throughput limitations.

View 3 Replies View Related

Generate Dial Tone Over Ethernet NIC?

Dec 9, 2011

Basically i need to test to see where the telephone lines are terminated, because when they where built into the walls the used standard cat5e cable to terminate it to an RJ-11 jack but over in the wiring panel it (i assume it is anyways) terminates to an RJ-45 jack but im not sure if this is really the cable for the telephone or something else, so i have a phone connected to the wall jack and a computer on this end and i would like to send a dial tone or any tone in general that the phone can pickup.

View 3 Replies View Related

Cisco Routers :: RV 220W - Create Matching Inbound And Outbound Rules

May 15, 2012

RV220W - I'm trying to create a one-to-one NAT connection to a PC on my network. I have 5 static IP's assigned by my ISP. I've gone through the step of 'registering' each IP in turn on the WAN port, and pinging that IP from an external device until it starts to respond, then I set the WAN IP back to the one I want to use to manage the device.
 
I think what I want to do is simple. I simply want to NAT ALL traffic hitting my 2nd IP address, let's call it 24.15.120.73 (not the real value) to 192.168.1.10 internally. I want ALL ports both UDP and TCP to be forwarded. This Server is then going to be one end of a VPN tunnel going to another site, but I don't want to complicate things with that for now. So I can't even seem to get one-to-one NAT working! I created the one-to-one NAT on the Advanced tab of the firewall and created rules for all ports for UDP and TCP, but I can still never 'see' the internal server from the Internet. Also, the server will not get out to the Internet (can't hit Google, etc).

View 2 Replies View Related

Cisco Switching/Routing :: 2960 - Cannot Have A Dial Tone

Sep 24, 2012

I have recently replaced some Catalyst 3550's with Catalyst 2960s PoE 48 port switches. Since the replacement I have had some issues with phones that will not have a dial tone. They are powered and the network config shows the correct configuration. They have the correct addresses for call manager and the router handling inter-campus calling. We tag the voice vlan separate from data and we use auto qos voip on the switches.

View 5 Replies View Related

Cannot Connect With A Port That Is Not Available / Or Is Too Busy

Dec 7, 2012

I cannot connect with a port that is not available or is too busy. How can a com port be reset?

View 1 Replies View Related

Cisco DPC3825 / DIR655 Routers Giving Error

Jun 20, 2012

i m trying to connect two routers a Cisco DPC3825 (r1) and DIR-655 (r2) and at the end getting the error. i have disabled the SPI firewall on r1 and connected an ethernet cable lan to lan between the two. i don't want to confuse with whatever the mess i have done previously,Tell step by step what i should do to connect these two routers.PS: in addition, the gateway ip of r1 is 192.168.0.1 with subnet mask of 255.255.254.0 and the gateway ip of r2 is 192.168.0.2 with subnet mask of 255.255.255.0. r1 has a ip range of 192.168.0.10 to 192.168.0.128 while r2 has range of 192.168.0.100 to 192.168.0.199.

View 7 Replies View Related

Cisco Routers :: RV042 Giving Out Certificate Instead Of Server?

Jan 28, 2013

RV042 router is giving out the outer certificate  instead of server certificate. Outlook anywhere is failing and we are receiving certificate errors for any secure site behind this firewall.  I'm not talking  about remote  management. I'm talking about people trying to access our  web site,  which is secured, and getting an error because the RV042 is  giving its  own SSL certificate instead of the Server's certificate.  Firmware Version:  1.3.13.02-tm.  I don't see any updates for that  hardware.  I do have it working on an RV042 with the same firmware at a different location.  How do we turn that off or keep it from happening?  Output from a test site Attempting to resolve the host name xxxx in DNS.The host name resolved successfully. Additional DetailsTesting TCP port 443 on host xxxx to ensure it's listening and open. The port was opened successfully. Testing the SSL certificate to make sure it's valid. The SSL certificate failed one or more certificate validation checks. Test Steps ExRCA is attempting to obtain the SSL certificate from remote server xxxx on port 443. ExRCA successfully obtained the remote SSL certificate. Additional Details Remote  Certificate Subject:

SN=California, L=Irvine, C=US, O="Cisco-Linksys,  LLC", OU=RV042, CN=68:ef:bd:b8:0f:78, Issuer: SN=California, L=Irvine,  C=US, O="Cisco-Linksys, LLC", OU=RV042, CN=68:ef:bd:b8:0f:78.Validating the certificate name. Certificate name validation failed. Tell me more about this issue and how to resolve it Additional Details Host  name xxxx doesn't match any name found on the server  certificate SN=California, L=Irvine, C=US, O="Cisco-Linksys, LLC",  OU=RV042, CN=68:ef:bd:b8:0f:78.

View 1 Replies View Related

Cisco Switching/Routing :: How To Setup Traffic Shaping On 4500X Outbound Port To WAN Routers

Mar 26, 2013

We have some ASR WAN routers which have a dedicated 400M interface to a remote site.
 
Servers on our Local network source the data through some firewalls via 10G interfaces, which connects to 4500X WAN switches then to the Routers on 1G links.
 
The sources are rate limiting the traffic but the routers are periodically dropping packets which I think is mostly due to burstiness in the traffic between as it traverses through from 10G links to 1G then to 400M. 
 
How to setup traffic shaping on the 4500X outbound port to our WAN routers.I'd like to see if we could buffer and smoothe out the traffic as it exits the 4500X WAN switch 1G port to the WAN Routers.

View 1 Replies View Related

Cisco Routers :: RV042 Giving Out Router Certificate Instead Of Server

Nov 28, 2012

Just installed RV042 router. And it's giving out router certificate instead of server certificate so people who are trying to access our secured server are getting errors. I'm not talking about remote management. I'm talking about people trying to access our web site, which is secured, and getting an error because the RV042 is giving its own SSL certificate instead of the Server's certificate. How do we turn that off or keep it from happenning?
 
The RV042 firm version is v4.0.0.07-tm (Aug 19 2010 19:19:50)

View 5 Replies View Related

Put Cisco IP Phone 7941 As Busy Mode / Occupied

Dec 15, 2012

I have a Cisco IP Phone 7941, and I would like to know how can I put the phone as busy mode / occupied, and after then how I can back from busy mode to available mode.

View 1 Replies View Related

Cisco VPN :: IPSEC VPN From SRP521 Dynamic IP To ASA5505 Static IP

Jun 18, 2012

I'm having problems configuring an IPSEC VPN between an SRP521 with a dynamic IP and a ASA5505 with a static IP. Static to Static is fine between these devices and I can configure that without problems.  Dynamic to Static however.

View 1 Replies View Related

Broadband :: Telephone Line Jack Not Receiving Dial Tone On Laptop

Dec 26, 2011

I can not get onto the internet via dial up. The message says that I have no dial tone. Using the same line, I get a dial tone on the phone. I can get onto the internet via a DSL connection, but it will not make a connection when I have a telehone line inserted in the phone line jack. This problem started after the power went off and on quickly two times. I have followed all the instructions that I have found to reset the modem, but to no avail. Is it possible that the phone line jack needs to be replaced.I have a gateway laptop with Vista program.

View 4 Replies View Related

Connecting DIR 815 Router To DSL Modem - Network Status Busy

Jan 12, 2013

I am trying to connect my DIR 815 router to a DSL modem.

I fill out the password, and the username the way it should be, but then when I try to get the modem to connect, it says the network status is busy.

View 1 Replies View Related

Cisco Routers :: RV042 - DHCP Giving Out Wrong Default Gateway And DNS Server

Oct 3, 2012

I have a RV042 router. The problem that I am having with it is that the DHCP is giving out the wrong Default Gateway and DNS Server. There is no option to change the DHCP server IP on any of the settings pages on the router. I am begining to think that there might not be a way to do it.  I see that there is an option for the DNS under the DHCP page but the Public IP that is being handed out is not the one on that page. I also have 2 WAN connections hooked up as well a DSL link and a Cable link (the cable link is the primary one).
 
The following information is provided in an effort to resolve this issue:
IP of Router 10.0.0.2
IP of DHCP Server (the one that is being handed out):10.0.0.1
IP of DNS (the one that is being handed out): 10.0.0.11
 
What I want to it be.
IP of Router: 10.0.0.2
IP of DHCP 10.0.0.2
IP of DNS 10.0.0.2

View 3 Replies View Related

Security / Firewalls :: Getting Busy Signal For Many Local Phone Numbers

Apr 2, 2013

I have AT&T Uverse and VOIP. I can receive calls but when I try to call out many local numbers and 800 #'s I get a busy signal. I called AT&T and they said everything looks ok to them. Could this have anything to do with Windows firewall or modem settings?

View 7 Replies View Related

Routers / Switches :: Connect Two Systems Together But Was Giving Error That Contact Network Administrator

Jan 30, 2012

Trying to connect two systems together but was giving error that contact network administrator,one system is laptop with wireless and other is desktop but connect through cable but running windows XPSamson

View 1 Replies View Related

Belkin Routers :: N150 Firmware Upgrade Giving File Format Error

Mar 19, 2013

I bought belkin N150 recently. I tried to configure with my ISP. They are surprised how I don't have DHCP option in the wifi configuration and asked me to upgrade my firmware. When I tried to upgrade. I downloaded the firmware from [URL] tried to upgrade. It is showing file format error.

View 2 Replies View Related

Cisco :: Inbound And Outbound Traffic In BGP?

Dec 6, 2012

I have two ISP, I want to divide Inbound to ISP1 and Outbound to ISP2.

View 3 Replies View Related

Cisco VPN :: PAT Outbound On 5540 For Traffic?

Feb 28, 2011

We're running 8.3(2) in the ASA5540. Users all over our enterprise connect to a business partner's application through the ASA/VPN. We have a class-b address space, and since the users are spread out all over the place, I have the entire class-b space as the local object in the ACL that allows traffic through the VPN tunnel.
 
The business partner has concerns that our entire address space is available to access the VPN tunnel. So I thought, to alleviate their concerns, to PAT all of our connections outbound to a single IP address.
 
How is this done in 8.3(2)?  We use ASDM to configure the 5540.  For example, say our class-b is 159.12.0.0 and the PAT'd IP address will be 199.30.36.6.

View 5 Replies View Related

Cisco WAN :: 887 Router - Two Outbound NAT On Dynamic IPs

May 27, 2013

I've got an 887M router which will be configured with two linke - one ADSL, one 3G - both of which will have (obviously) a separately suppplied IP address from the different ISP's being used. The 3G is a backup - plain and simple - for use only when the DSL service flakes out (which it does often)
 
Routing is pretty simple - I'll either do soemthing with a bit of PBR, or a simple weighted static, but the NAT has me scratching my head a little.
 
Can I have two outbound NAT pools (ip nat outside) for each interface which will be used ONLY for traffic going out the interface concerned?
 
For example, I have one for the primary link
 
ip nat inside source list 2 interface Dialer1 overload
 
Can I do the same for the second dialer interface like this
 
ip nat inside source list 2 interface Dialer2 overload
 
and have them automatically switch to using the dialer 2 IP for the outbound NAT if the dialer 1 link fails?
 
I don't think I've ever come across this before, so I'm not sure if it can even be done.

View 1 Replies View Related

Outbound Packet Loss

Aug 10, 2011

For about the past 2 or 3 months, I have been experiencing outbound packet loss at about the same time every evening. That timeframe is about 7 PM - 10 PM. This is most noticeable on Teamspeak 3 because of the voice disruption that other users report to me.

View 1 Replies View Related

Cisco :: Outbound Calling To Two ISDN BRI Ports?

Oct 21, 2011

Both of these ISDNs are up, this gives us 4 channels. Someone said they recieved a busy tone when they attempted to dial out. I looked over the system and seen there are two outbound pots dial-peers. Each dial-peer references one of the BRI ports. The preferences are the same on each dial-peer. I think what is happening is that the system is randomly selecting one of the dial-peers due to the preference, even if both channels of the BRI are in use. How does the system know if that port has both channels in use? I've not used ISDN before, so tried to enter the B-channel sub interface and the system (UC500) tells me I cannot do this. I was thinking about adding each channel into a trunk group and then referencing the trunk group in the dial-peer. I can obviously add both BRI's into one trunk group.

View 2 Replies View Related

Cisco WAN :: 6509e BGP Outbound Path Selection

Sep 20, 2012

I multi homed to dual ISPs using a single 6509e. Currently, I am only receiving a default from wash ISP and marking one with a higher local pref. most of my traffic flow is inbound, so this config meets my need. The issue I have: if either ISP has has an outage upstream from my directly connected peer, my router does not detect that and continues to send traffic out thru that provider only to be black holed. My 6509 will only support 256k routes, so full route tables isn't an option. I could receive partials from each ISP. Is there any other method to detecting this upstream ISP issue and then adjusting my local pref on my default to use the alternate provider path?

View 3 Replies View Related

Cisco WAN :: Reserve Outbound Bandwidth For VoIP 877

Mar 31, 2011

I have a Cisco 877 on an ADSL connection.  QoS isn't doing the trick -- I need to reserve 200 meg or so of my outbound (upstream) bandwidth for VoIP to end complaints about voice quality. Any example of how to classify SIP, RTP, IAX, and Skype traffic and put a rate limit on anything that doesn't fall into that category?  The VoIP phones also are in their own IP range on the LAN side if that would make things easier...or I could even connect them into a specific port on the internal switch in the router.

View 9 Replies View Related

Cisco WAN :: 6509E - BGP Outbound Path Selection

Mar 4, 2013

I  multi homed to dual ISPs using a single 6509e. Currently, I am only receiving a default from wash ISP and marking one with a higher local pref. most of my traffic flow is inbound, so this config meets my need. The issue I have: if either ISP has has an outage upstream from my directly connected peer, my router does not detect that and continues to send traffic out thru that provider only to be black holed. My 6509 will only support 256k routes, so full route tables isn't an option. I could receive partials from each ISP. Is there any other method to detecting this upstream ISP issue and then adjusting my local pref on my default to use the alternate provider path?

View 3 Replies View Related

Cisco WAN :: 4900 - Outbound QOS Police Configuration

Jan 12, 2011

I need to attach a QOS policy to a layer 2 WAN interface between two sites.  This is actually an extended LAN circuit with 500Mb/s of allocated bandwidth.    The interfaces are Gigabit so I want to make sure I don't attempt to transmit traffic faster than 500Mb/s.  What is the best way to implement an outbound QOS policy that sets the minimum and maximum speed to be the same? This policy will be implemented on a 4900M with the 20 port GigE module

View 3 Replies View Related

Cisco :: 4507 - Filtering Outbound Sys Log Messages

Apr 10, 2013

How can I filter outbound sys log messages, so they include only configuration changes messages..
 
On Cisco 2900 I used:
 
logging discriminator CFG LOG msg- body includes "PARSER" | "CONFIG"
 
logging host x.x.x.x discriminator CFG LOG
 
logging x.x.x.x
 
How can I do the same on 4507? This feature on Cisco routers is called "Reliable Delivery and Filtering for Sys log" and is available for 12.4(11)T  and 12.2(33)SRB (7600) . I am running Version 12.2(25)EWA6 on my Catalyst, so it is not available.
 
The software I am using is a simple solar winds sys log server.

View 2 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved