Cisco Routers :: RV180W - Outbound Public IP Address?
Mar 26, 2013
What I'm trying to do seems pretty basic, but I cannot get it working on the RV180?I have 5 Fixed IPs. Using Access Rules I have configured a few inbound rules with specified WAN Destination addresses and these are correctly port forwarding these inbound ports on the specified Public IP addresses. Perfect!
However, for outbound, I need to do the equivalent for one public IP for outgoing SMTP so that our mail servers public facing address is not the standard WAN address and therefore will not fail a reverse DNS lookup. At the moment I have emails bouncing all over the place and panic has set in. I thought the SNAT option was the soltuion, but that just seems to break traffic flow completely on the specified port. I had this working no problem on my old Netgear, but I had to replace it due to throughput limitations.
I'm interested by the router Cisco RV180 or RV180W.
So as to increase security, i would like to set a MAC adress access restriction for all peripherals that would be connected to the router (10 computers, 2 servers, 6 Synology NAS) : only allowed MAC adress should access to the internet and network ressources.
Does the Cisco RV180 or RV180W have an IP to Mac biding feature and a Mac adress restriction feature ? If yes, how many peripherals/computers can be set ?
For example, only 30 mac/IP adress can be allowed on my actual router and it is not enough.
I got : RV180W router updated with the last firmware.Static IP for the DMZ host (Synology Server 212+) My problem is that I had try all combinaison since 10 days to get IP source in synology interface (to block IP's of bad connections...) but, I only see the RV180W adress....So impossible to block bad connections IP.
I would like to ask if what is the difference between RV180W-E-K9-G5 and RV180W-A-K9-NA specifically the -E and the -A. As far as I know -A is the compliance code for Philippines. Am I right? If yes, what about -E? There is a documentation for wireless complaince on Aeronet devices but what about these SB products?
I have a n150 and it only allows private ip addresses for the lan setup. Is there anyway to assign a public address? I need to have the DHCP use a public range and I can't do that unless I can set the router to a public ip.
I have an ASA 5510 running version 7.0. I have a problem with an exchange server using a static map and its outbounc connectivity. It connects outbound through the global address even though inbound connectivity works fine through the static mapping. The recent changes are changing of the zero route through a different interface (there are to circuit connected to this ASA on different interfaces). So the idea was to get all workstations in the office using the global address and routing out through one circuit, and the servers connecting in/out through the other circuit. Shouldn't a static mapping ignore what the zero route is?
Here are what I believe to be the relevant configs.
interface Ethernet0/0 description New 6mb circuit speed 100
[Code]....
So exchang2 server can be connected to from the outside properly via IP xxx.207.51.231/exchange2-outside, but all outbound connections from this server are going out via IP xxx.122.47.218/circuit-6mb as do all the workstations due to the global address statement.
I just migrated our office network router to a RV082. While configuring it, I came across three problems:
(1) From our ISP we have four public IP addresses which I want to make use of for outbound traffic. With the previous router we used we could configure LAN IPs(ranges) to map to static public IPs. Does RV082 support this? I could not find an option for that at the web-interface. From what I understand the 1-1 NATing only goes both incoming and outgoign ways and actually is 1-1 and not the many-to-one I am looking for.
(2) How is it possible to configure incoming port forwards to use a specific WAN interface? Will it always be the primary WAN interface?
(3) Does the telnet access provide more configuration options? I could not log in to it with the same user credentials as with the web-interface.
Serial Number : NKS1532xxxxFirmware Version : v4.0.4.02-tm (Jul 4 2011 13:30:56)PID VID : RV082 V03Firmware MD5 Checksum : 1f84d8d0a2a8b99f9bfa4409e64547aaLANWorking Mode : Gateway
How to set the default outbound policy as block in access rules of rv220w? I configure my company router RV220W to block all outbound service traffic, just allow outbound service as : http, https, smtp, dns_tcp / udp. it works fine for some hours, the next day, the rules like expired, the https / smtp / DNS service fail to outgoing, only the http is still ok? What happen? Now I just set the default outbound policy as allow, all traffic can go out, but that is meaningless for a firewall device.
I installed the RV180W yesterday and decided to play with it a bit today. I got stuck on the firmware update. Tried different browsers on different PC's. Tried going to 1.0.1.9 first. I have the "reset all configurations" button checked. After looking through the posts here I'm not sure this firmware will even fix my next few problems(port forwarding etc). Is there a trick with this device?
I'm trying to make the VPN connection between two routers CISCO RV180w.I performed the basic configuration in cisco "server". I did the same in cisco "client".The following configuration and logs, do not know what to do ...
SERVER CONFIGURATION: IKE Policy Configuration: VPN Policy Configuration: CLIENT CONFIGURATION:
We have installed a fiber internet access and have the ONT from the provider already installed.We're trying to use the RV180W to use this internet connection. [code] So I need to configure the router with the .36 static IP on the WAN, and using the .37 gateway and the provided DNS servers. I also need that this WAN is tagged with VLAN ID 20. I'm only able to set VLAN ID on the LAN ports via the admin interface.
I am struggling to configure my new RV180w router to accept a VPN connection from my Apple computers.
I wish to use IPSec with Group and Pre-Shared Key authentication. The RV180 has just replaced my 800 series ADSL router and I want my remote clients to be able to connect using either the VPN client capability built into the OS X operating system or the Cisco VPN Client software installed on their Macs.
So far, using the RV180's web setup screens, I have created a VPN Policy and a corresponding IKE Policy was created as well. I couldn't see anywhere to include the 'Group' name. I have created a user but wasn't sure of which Protocol to use so I am trying XAUTH.
At the client end some people are connecting using Cisco's VPN Client software Download Software - Cisco Systems
Some people, with OS X 10.6 and above, are using the Mac OS X network built-in VPN client.
We all connected without a problem to the previous 800 series router using IPSec with Group authentication and Pre-Shared key.
i've installed the new firmware on my router and now the UC is showing 100% all the time. I've tried to factory reset it, it's doing the same thing. If I downgrade to previous firmware, it goes back to normal . I've only 1 PC in my network (test lab), so no big traffic here. is it a bug ?
RV220W - I'm trying to create a one-to-one NAT connection to a PC on my network. I have 5 static IP's assigned by my ISP. I've gone through the step of 'registering' each IP in turn on the WAN port, and pinging that IP from an external device until it starts to respond, then I set the WAN IP back to the one I want to use to manage the device.
I think what I want to do is simple. I simply want to NAT ALL traffic hitting my 2nd IP address, let's call it 24.15.120.73 (not the real value) to 192.168.1.10 internally. I want ALL ports both UDP and TCP to be forwarded. This Server is then going to be one end of a VPN tunnel going to another site, but I don't want to complicate things with that for now. So I can't even seem to get one-to-one NAT working! I created the one-to-one NAT on the Advanced tab of the firewall and created rules for all ports for UDP and TCP, but I can still never 'see' the internal server from the Internet. Also, the server will not get out to the Internet (can't hit Google, etc).
I just recently switched from the WRVS4400N to the RV180W. I have 4 VLANs, and I want VLANs 1, 2, 3 to communciate freely, but I DONT want VLAN 4 to communicate with anybody, just Internet access. On the WRVS4400N, I was able to do this using the Firewall > IP Based ACL. I notcied that the RV180W, does not have such an option. I am sure there is something I am missing, I just cant find out how to isolate VLAN 4.
we've changed our rv042 for a rv180w and now when I try to upload files to my ftp server (vsftpd under centos) it get stuck at 100%.I've changed my ftp server to proftpd instead of vsftpd and everything's ok.but vsftpd isn't the problem since i was able to upload with my rv042 without any problems.so i guess there's a problem with the rv180w security.i've already disable stealth mode and it's doing the same thing when i try to upload to the same server but through the vpn tunnel, everything's ok.So it's really in the rv180w lan->wan routing
Have not purchased RV180W at this time, therefore have not read manual. Need for small office, 2 VPN logins max & not 24x7 use. What VPN client software ? (using Win7-64bit laptops)
I did notice software called Quick VPN Client 1.4.2.1 for download.
Does buying RV180W allow download of Cisco Systems VPN Client software ?
I am located in UK which uses PPoA for ADSL broadband. I use a DrayTek Vigor120 ADSL2 Modem to act as an ADSL bridge and PPoA to PPPoE converter. This passes the ADSL authentication requirement (and subsequent single static IP address) to the Cisco Small Business RV180W sitting behind the Draytek. However, the RV180 (Firmware Version 1.0.0.30) cannot form the PPPoE connection. I have tested the modem, adsl username and password by creating a PPPoE interface on my computer and connecting this directly to the Draytek modem. The computer receives the expected IP address and I can ping remote public IPs. I have entered the username and password into the PPPoE profile,
Authentication type: CHAP (confirmed by ISP but I have also tried all other options just in case). Connection Type: Keep Connected. MTU Size: 1400 (also tried default, which worked OK on computer interface). MAC Address Source: Use Default (I have successfully used combined modem/router so a "fixed" MAC address is not required).
I live in China. I want all of my PC's and devices to connect through the RV180W VPN Router to a VPN provider in the US so that all of my traffic is encrypted and appears to have a US IP address. I need to find a VPN Service Provider that supports the RV180W and how to configure it. I don't want to configure every PC and device, I just want them to use the VPN conneciton at the router.
I am using DynDNS in lieu of a static ip. My ISP changed my WAN ip last night as expected however the RV180W did not update the WAN ip, and so the router is now offline. Using a secondary internet connection I have logged into DynDNS.com and checked my hosts file and confirmed the ipa has not updated since March. I changed the update period from 360 to 2 so this never happens again, but I need to now change the WAN ipa in the RV180W to match the new one. I remember a screen that shows the current WAN ip address greyed out under the present one, but I dont recll where to go to get to that. I am at a loss as to where I go in the RV180W to change the WAN ip address.
We are deploying over 20 RV180W Routers for a client and need to find a faster way to configure them for shipping.We have created a base image (all settings that will be shared between the 20 locations), we need an easy and quick way to make IP changes for the 3 VLANs and Local Security Groups for the IPSEC VPN.I tried to edit the CFG file by hand, but the checksum fails when it is loaded into the RV180W.How can I accomplish this? Can I manually create the checksum?Can I remove the checksum?
Comcast has indicated that this is required for IPv6 to work, and since it means gatting a /64 address space for my network I am understandably eager to tak advantage of this new functionality when it is available in my area.
I am wanting to purchase the RV180W for a small Optometrist office. We are beginning our transition to EHR and what to ensure the RV180W is HIPAA compliant and if not what would be the next best product for about the same price?
I have rv180w (firmware 1.0.1.9) and 1 Gbit/s internet.When i turn on WAN Traffic meter, WAN speed down to 100mbit/s.I didn't find any suggestions in official documentation.Is this a bug or undocumented feature?
Our company own a RV180W router. It works well with firmware 1.0.1.9 but with firmware 1.0.2.6 it is impossible to SSH between our devices. Ping still works though.
We just recently invested in 5 RV180Ws to serve as replacements for the aging routers in 5 of our shops. Additionally, we bought them because they seem to offer robust WiFi options for customers/guests, such as multiple SSIDs and restricting 'public' traffic to it's own VLAN.
Straight out of the box we updated them to the new firmware, 1.0.2.6, set up 2 SSIDs (one hidden for employee use, and one broadcast for customer use), and plugged them in.
Everything seemed to be going great until we walked to the other side of the shop and watched the signal drop off almost completely. These are fairly small premises and the router can't be more than 8 metres from where the customers are, and yet the signal is so weak that it's almost unusable.
For reference, we have the WiFi running in B/G/N mixed mode to maximise compatibility. with the channel and width set to their defaults (Auto and 20MHz, I believe).
Moving the routers is only semi-viable; these are meant to serve as replacements for existing IT equipment, and the cabling situation means they can only really go in the office space near the rear of the shops. Also, it simply shouldn't be necessary; WiFi should extend well past 8 metres without issue.
