I have a srp521 and want to set it up as a vpn server so I can connect back from outside.On the router under the vpn tab I only have
Site to site IPSec VPN
IKE Policy
IPSecPolicy
GRETunnel
VPN Passthrough
Page 191 of the srp500 manual says Click VPN > Cisco VPN Server > Group. The Group window opens The manual also says only the serer or Site to site will work at one time, so where do I make the change to bring up the vpn server option?
I am running 1.1.24 and spa303 phones I have a qos policy setup to mark all packets
The following is my qos
information 192.168.1.15/24 makring enabled cos/DSCO DSCO Value 0xb8
On my upstream device I only allow traffic that is marked with this dscp value. No traffic is coming through. RTP traffic is marked because it comes off the phone marked but I would expect the qos Policy so mark everything going to that ip space to be marked.
I have a customer with a Sonic wall that I want to replace with a 521.He currently has port forwaring setup so that only 3 ip addresses can access the port forward. Everyone else is dropped. Is there a way to do something similar?I can make it work for a single one via the DMZ tab with a source ip address. but there is not a way I can find to add the allow for the other two remote connections.
I'm having problems configuring an IPSEC VPN between an SRP521 with a dynamic IP and a ASA5505 with a static IP. Static to Static is fine between these devices and I can configure that without problems. Dynamic to Static however.
I planned for my customer to replace his old LMS 4.0.1 server under Windows 2003 by a new server under Windows 2008 R2.Customer wants also to set a new LMS name and IP address for the new server under Windows 2008 R2 and keep both servers on the network.I'm wondering what could be the best procedure to do that migration.Can I used backup / restore procedure in that case ?If yes, what file must I modify to adapt the new LMS configuration to new hostname and IP Address ?
I'm trying to change the IP address of the smtp server on cisco LMS 3.2.1;I have changed the IP on the GUi and when it didn't work, in the regdaemon. xml file, but it did not work too;When I capture packets from the LMS, it still sends emails to the old IP;
I have configured the NCS 1.1.1.24 and its running fine, but i used the IP address 10.18.20.7(it was the WCS server), but now I want to use 10.18. 20. 8 (NCS Server) ip address.
so what should i do to change the ip address: I know only 1 thing that is, change the ip of the interface gig 0 .My main task is to run WCS and NCS parallal.
I rdp into our server 2008 via IP. This is a router on ip 0.1, this is forwarded to my server on IP 0.3. This server was setup with DHCP default gateway of 0.1. We added a new outside connection on IP 0.2. I was talked through the changes so that internal DHCP requests went to gateway IP 0.2 but RDP still used 0.1. I plan on getting rid of 0.1.Where is the setting to change the RDP to use default gateway of 0.2?
I can't change my DNS servers. I went to my Network Settings and changed the settings for my DSL adapter. I manually changed the DNS servers to OpenDNS's servers, but when I looked again, the settings always change back to the localhost, 127.0.0.1. I tried to reset my DSL but still no luck.
we are running LMS 4.0 on Windows Server 2008, and just changed the hostname of the server, as the former on reflected it being a test system. However, after rebooting the server (as required by windows), the LMS application did not launch.After rolling the windows server back to the old hostname, the LMS started working again.Why is this? Isnt it possible to change the server hostname after the LMS has been set up for the first time?
I have two 5500-controllers and one WCS-server. Now I will have to move the WCS-server to another subnet and change the IP, but it will keep the name.Will that effect the connection between the controllers and the WCS?Do I have the change anything in the configuration on the controllers or the WCS-server?
i see there is an option to "allow password change" or "force password change" for guest roles in the NGS. But when i created a guest account using this guest role, after webauthentication , there is no prompt to change password. Is this the intended behaviour or is there anything else that i need to configure. Looking at it, i am not sure how the NGS would allow a "guest user" to really overwrite the password by allowing password change. ? is that not a security risk as well for the NGS ? my setup has 5508 anchor controller and NGS communicating via RADIUS.
We have a number of 5505 ASAs at remote sites all of which are configured to connect to one of two head-end servers.We need to change the primary head-end IP addresses. At the moment devices are successfully connected to the secondary.If we issue vpnclient server i.j.k.l e.f.g.h then the device drops off the network and won't reconnect until it is power cycled.If we make the changes in ASDM using the GUI to remove the old primary and add in the new primary the ASDM says "No changes made".Devices are running 8.2 and 8.4 code and behaviour is the same.
how to change head-end server IP addresses without the device disconnecting and not coming back up? According to the configuration guide the ASA should cycle through the addresses every 8 seconds until it can connect - but it doesn't seem to do this as it won't connect to the good secondary head-end either!
It works fine on both my pc and wifi laptop, provided I give a fixed DNS server that was entered by my internet provider. My IP address is set to 'obtain IP address automatically' but my DNS is set to a preferred DNS by the provider. I have to set this on my notebook as well in order to access internet. If I set it to obtain DNS server automatically, internet stops working on that machine.roblem is when I try to access internet through my phone it does not work, because I have no option to enter a DNS server there. Internet works fine on my phone using another wifi router where the obtain dns address automatically is enabled.
I´m Trying to synchronize the clock with NTP server external, these ntp server only support NTP version 3.Can I change the NTP version in the ACE4710 Appliance to support the ntp server external?If is possible, How I can change it ?
This is the version:
Cisco Application Control Software (ACSW) TAC support: [URL] Copyright (c) 1985-2011 by Cisco Systems, Inc. All rights reserved. The copyrights to certain works contained herein are owned by other third parties and are used and distributed under license.
Lately, Ive been trying to change my router DNS to OpenDNS. Somehow, after changing it, I couldnt access the router page at 192.168.0.1, getting the error 500 message. I unplugged and plugged the router with no effect. Im using a dlinkddns.com dynamic IP, and have a few ports forwarded for my DVR. The router model is DIR 615. want to change the DNs for speed and filtering purposes.
One of the companies I work for uses a DIR 655 router. I'm having some trouble using FTP there.Initially the problem was that FTP software would hang or give errors when trying to change directories on the remote server. This problem went away when I switched from passive FTP to Active FTP.Now using Active FTP, the files appear to be uploaded with no problem. However, on closer inspection, the uploaded file has 0 bytes on the remote server.
We are uploading from a Windows 7 machine and uploading to our Web Hosting Company's Windows Server. I've actually written the one piece of software that is showing this problem but it uses a widely known open-source FTP library written in .NET. I've never encountered either of these problems with my software until I encountered the DIR-655.The other FTP software client I've tried is FileZilla. It has the same problem, 0 bytes files when using Active FTP.
One solution I've seen on DSLReports was to disable the Stateful Packet Inspection part of the firewall (known as SPI). This is really not a good solution for two reasons. Number one, I do not have access to the router's firmware/ configuration. Number 2, the company has a DIR-655 because they want the additional security. If we're going to disable SPI it just defeats one of the major purposes of owning the DIR-655.
I have both boxes heading off to ACS for TACACS lo gin authentication and for command authorization. When I first set things up everything works fine. I have a shell profile configured in ACS with Cisco-av-pair*shell:roles="network-admin" to set the network-admin role. I even have command sets configured to deny the use of configure terminal as I am using switch configuration profiles. Everything runs fine. User lo gins are authenticated by ACS and users have the correct command set applied to them.
The problem comes when I make a change to a shell profile in ACS. Even something as simple as changing the name of a shell profile causes the 5520's to crash as soon as I try to log on. If I unplug the management link so that the TACACS server is unavailable I can log on fine with the local admin user.
The NEXUS console reports this error. (amongst many others)
EDNAM-NEXUS-2 %$ VDC-1 %$ %SYSMGR-2-SERVICE_CRASHED: Service "Tacacs Daemon" (PID 4331) hasn't caught signal 11 (core will be saved).
A show system reset-reason shows:
EDNAM-NEXUS-2# sh system reset-reason ----- reset reason for Supervisor-module 1 (from Supervisor in slot 1) --- 1) At 389 usecs after Wed Jan 18 12:32:49 2012 Reason: Reset triggered due to HA policy of Reset Service: Tacacs Daemon hap reset Version: 5.0(3)N1(1c)
I have a server with 4 ethernet ports, 1G, they are bonded together, two of them was pluged into cat6500 module WS-X6724-TX. now we have moved the two ports to the replace module WS-X6748-GE-TX.
I have checked server side, the bond configuration are same no changed. what is possible reason replace module will cause link offline? why "sh run all" give the port is shutdown?
Two years ago I got wireless internet, and when I did, my internet provider sent a wireless router that I have been using successfully with no problems. But the other day, my fiance noticed that we are being charged a fee for using the router provided by the internet provider, and so he decided it we should skip the fee by buying our own wireless router.I've tried hooking up the new router I got a few times but it doesn't work. I already have an existing network and all, and the internet always works when I plug in the provider's router, but when I plug in the new NetGear WNDR3300 router I bought, it doesn't even acknowledge that it's hooked up to the internet and I don't know how to get it to connect with my existing network so that I can send the provider's router back.
I use TZO.com DNS servers and it used to work on my old E2500 router, but not on the RV110w. As seen in the picture, it has this message: DDNS has been disabled. No change in the IP Address. I don't know what to do at all. My other question wouldd be, what do I have to type in the boxes. Such as for password, do I type in the TZO Key.
Belkin Router N300 Model:F9K1002V2 apparently forces me to have specific LAN and WAN IPs that I have been unable to change.My ISP has been changing my IP and advising me that everything works without issue. It's true that my IP does change, but only if I am directly connected to my modem - I have a completely different IP. If my router is connected to the modem and I am connected either by Ethernet/wifi from the router, my WAN IP is displayed as my IP & the completely different IP is nowhere to be found.
The issue is that this WAN IP seems to have been banned on a game that I played on a daily basis. Game support has not been responding to my requests & I know my account on that game still exists because I am able to play it when I'm directly connected to my modem. Connecting with my modem is not an option, as there are others in my home that also need to use wifi.So, if it's not already obvious, I'm looking for a way to change my WAN IP ... without having to toss out the product and buy a new router - which I am seriously beginning to consider it.
I have changed administrator password to a secure one, just after the changind the password it logged off and offered to login. Now when I put the same password it writes: Invalid password for Admin user Password I used: 8_^!-,Opc: 5Gj3v5<Xb06?9z\SeWr2z9axdPa-f+L:Wj]NzEF2>v!Fu&lS0 There were no warnings that some symbols are not allowed, etc.
How can I access my router? what should I remove from the password to get access?
