Cisco WAN :: 2851 Router Showing Error For Peer Set Configuration
May 28, 2012
We have Cisco 2851 Router part code CISCO2851-SEC/K9 facing issue while set peer configuration, issue description below.
Issue:We are facing the problem while configuring set peer as when we try to this we face error like 'unable to set peer.maximum numbwe of peer (40)exceeded'
We suspected the IOS issue hence we have gone for IOS upgrade for this Router but this error is still coming while configuring set peer.
Previous IOS: c2800nm-advsecurityk9-mz.124-15.T7.bin New IOS:c2800nm-advsecurityk9-mz.124-24.T7.bin
We are attaching here the snap shot of error that is coming while configuring the Router with set peer command along with show tech of the Router to understand this case brief.
View 1 Replies
ADVERTISEMENT
Mar 5, 2011
i have 2851 router and it is hanging when i login on it while it is hanging it gives me the following error message: [code]
View 2 Replies
View Related
Apr 24, 2013
Up to today I used Verizoon 4G to a Windows Visata box running Internet connection Sharing to get my home lab connected to the Internet . All was working well.
Today I had Hughesnet come and installl their service and I can no longer get access to the Internet from my PC netowrk. my VPN to my office for my IP phone coomes up an works just fine. At the router I do have Internet access which then leads me to believe that my problem is NAT related.
My router is a 2851.
When I enter PING 4.2.2.2 I get !!!!! but when i enter PING 4.2.2.2 SOURCE 192.168.69.3 I get .....
Here is my config info:
crypto isakmp policy 1
encr 3des
hash md5(code)
View 1 Replies
View Related
Feb 2, 2011
I am having issues bringing up a tunnel between a cisco 861 router and Cisco 2851 router. Tunnel has been dropping every week atleast once or twice. Usually router reboot fixes it but today it is just not coming back up. have updatee remote, reloaded the config still no use. It seems like it is partially coming up but I see the following two messages on the main router:
1- Death by retransmission P1
2- 11:03:03.789: %CRYPTO-6-IKMP_NOT_ENCRYPTED: IKE packet from 12.234.109.169 was not encrypted and it should've been
I have checked the config on both routers it is the same as the VPN was up and we didn't make any changes on either of the two routers.
View 4 Replies
View Related
Nov 22, 2011
we have ACS 4.2 and 2851 router with IOS 15.0(1)M4. There is authentication failure with error no 254. Is there any compatibilty issue with 15.0(1)M4 IOS
View 1 Replies
View Related
Dec 26, 2010
I had these error messages on both my Cisco 2851 and on my Cisco Catalyst 6506.
On Cisco 2851:
%SYS-SP-3-CPUHOG: Task is running for (2000)msecs, more than (2000)msecs (4/4),process = SEA write CF process. [code]...
And on 6506:
Dec 27 15:20:55 MET: %SYS-SP-3-CPUHOG: Task is running for (2000)msecs, more than (2000)msecs (129/129),process = SEA write CF process.[ code]...
I have these IOS versions on my Cisco:
Cisco 2851: 15.0(1)M4
Cisco 6506: 12.2(33)SXI
View 3 Replies
View Related
Aug 29, 2010
I have a Cisco 2851 (c2800nm-advipservicesk9-mz.124-25d.bin) Router configured with one site-to-site vpn. Is it possible to configure a failover vpn tunnel on this router?
View 8 Replies
View Related
Oct 31, 2012
I seem to be having an issue getting a 3xT1 bonded solution to work. I can get 2 out of the 3 T1s to come up and pass traffic, but I can not get the third one to be added to the solution.
Hardware: 2851
IOS: c2800nm-advipservicesk9-mz.124-15.T8.bin
Modules:
NAME: "VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1 on Slot 0 SubSlot 0", DESCR: "VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1"
PID: VWIC2-2MFT-T1/E1 , VID: V01 ,
[Code]....
View 4 Replies
View Related
Feb 13, 2011
I confgured one L2L VPN on my ASA 5505.
How to add another L2L configuration for an additional peer ?
View 4 Replies
View Related
Feb 25, 2013
I am working on wi-fi networks (ISP), So I need to block the peer to peer on my network.My network involves cisco switch 2950/2960, cisco 2800 routers and Access Points, config for peer to peer blocking, for this where I need to config either switches or router.My network basic setup is, The internet will pass from router to switch and then Access Points.
View 1 Replies
View Related
Apr 19, 2012
I got ASA 5510 with base license, can I block all Peer-2-Peer traffic from inside to outside.
ASA Giga 0/0 connected to ISP Router 2811
ASA Giga 0/1 connected to LAN switch 3560
View 3 Replies
View Related
Jul 25, 2011
I see that Application protection - blocking peer-to-peer file sharing traffic is a capability of Cisco IOS Firewall. How do i configure my Cisco 2911 ISR to block peer-to-peer file sharing traffic?
View 1 Replies
View Related
Feb 13, 2013
I am facing issues in blocking Peer to Peer applications in LAN. I am using 881 Cisco router and below is the config done. [code]
View 1 Replies
View Related
Jul 31, 2011
I recently bought the WAG320N can I block Peer to Peer file sharing on my Network?
View 3 Replies
View Related
Jul 31, 2011
I bought my WAG320N, I too have the internet drop out and from reading in here is a very common problem. Cisco really should bring out a new firmware version and address this issue. Any way you can block peer to peer file sharing with the WAG320N? If so how do you go about it?
View 1 Replies
View Related
Jan 28, 2011
One of the schools whose networks I administer has a peer to peer network running about 30 xp machines. DHCP is achieved and DNS settings distributed via a basic Linksys router; is there any way of distributing proxy server address and port short of entering manually in LAN settings of IE on every terminal - there is no budget to install a server.
View 4 Replies
View Related
Jan 18, 2011
i just set up my 2Xp pc's and one windows7 laptop peer to peer for file and printer sharing but i can not configure internet connection for those pc's
View 2 Replies
View Related
Sep 17, 2008
I got a WLC4404 running software version 5.1.151.0 with 40 LWAPPs (mostly 1242AG). We got new Dell Latitude E6500 Laptops with Intel 5100 NICs. After upgrading the bios to the latest version and installing the latest wlan driver, wireless is working the most time.After about 4 reboots I see the following message in the WLCs logfile: "Thu Sep 18 13:53:10 2008 AAA Authentication Failure for UserName:host/hostname.domain.name User Type: WLAN USER".After I disable the wlan-card, it's working again.
View 7 Replies
View Related
Oct 16, 2012
I have configured remote access VPN with radius authentication in my firewall ( ASA 5510). When tried to connect the VPN with Cisco vpn client, the following error is showing,
"Error: Secure VPN connection terminated by Peer. Reason 433 (Reason not specified by peer)".
View 1 Replies
View Related
Mar 12, 2011
i want to set up my two computers /win xp/ installed using peer to peer network , just tell me the needed steps
View 2 Replies
View Related
Jan 24, 2013
I want to prevent guest from doing peer - peer communication on my Guest (5508) controllers. Is this a feature on the WLC or only by applying an ACL on the router interface?
View 2 Replies
View Related
Sep 2, 2011
webpages not opening and showing some error
View 1 Replies
View Related
May 12, 2012
my sons laptop wifi is showing error 31 and i cant get it to work
View 2 Replies
View Related
Mar 5, 2013
We have a stack setup with 2 C3750x-12s and 5 C3750x-48p switches. We have two of these stacks. One is working and responding with snmp just fine. Our second one is showing the errors in the logThe only difference i see between the two stacks right now are the sw versions.
View 1 Replies
View Related
May 15, 2012
I have several switches that don't show the key cryptext in their config when I do a show run.What would cause this? I am generating self-signed keys via "crypto key generate RSA"
View 2 Replies
View Related
Aug 6, 2012
I have a new 3925 router and it came with 1 VWIC3-4MFT-T1/E1 card installed. I added a 2nd one and although it shows up in inventory, the interfaces do not show up in configuration in any form, interface or controllers. I used to just install a card and it would be recognized, is that no longer supported and is it platform specific or IOS specific?
View 3 Replies
View Related
Jun 12, 2013
I have reconfigured the FEX numbers attached to a Nexus 5548 running on NXOS5.2 If I do show running-config the interfaces are not there anymore. But if I do show startup-config the old Fex interfaces still shows up. I did try write erase then saved the running-config and its still there.
View 1 Replies
View Related
Dec 19, 2012
My cisco works LMS3.2 is not showing recent configuration of my Cisco devices. also it dont show any change report on last 24 hours or even if i select x number of day, looks like its not saving any changes made on devices.
today i logged in and cisco ASA was showing this in status as well Configuration Last Archived Time May 03 2012 11:27:46 EDT on checking i could see it is same date when cisco ASA was added in cisco works. do i need to click some where for auto update configuration changes and latest confoguration in cisco works setting?
View 1 Replies
View Related
Jan 31, 2012
We have Cisco router 2851 and asa firewall. We configured on he router for IP phones and ISP connected. The ISP directly connected on the router and asa firewall connected to the router. We have plan to configure VPN on the router. We have available public ip address. if i configure the VPN on the firewall we need to configure firewall local ip address to public ip address. SO how to configure firewall local ip to public ip ? Where we can configure , mean on the router or firewall. Firewall and router configuration.
View 11 Replies
View Related
Jan 23, 2013
Is the 2851 router meet these requirements ? if no. What is the must specific series of the routers suitable for this requirement:
1. Comprehensive interface range supporting T1/E1, NxT1/E1, FE, and High-Speed WAN .
2. Wide array of Layer 2 access protocols including Frame Relay, Ethernet, and PPP/HDLC .
3. Rich and granular QOS and instrumentation for prioritizing mission-critical traffic such as voice .
4. A modular platform with a broad range of interface options.
5. Network Address Translation (NAT), and IP Sec .
6. Four (4) auto sensing LAN Ports (10/100/1000) Mbps built-in routed ports.
7. WAN Interface Slots (4-6 option Slots) .
8. WAN Interface Modules (2xT1/2xE1/2xSerial/2xFE/DS3).
9. Memory (512/1024 MB DRAM) .
10. Built in redundancy (Power Supply) .
11. Two (2) Integrated GE ports with copper and fiber support .
12. Support for a Small form-Factor Plugged ( SFP) port for GE.
13. Support Network Timing Protocol (NTP).
14. Security: On-board encryption Support of up to 2500 VPN tunnels with the AIM-HPII-PLUS Module Antivirus defense support through Network Admission Control (NAC) many more essential security features .
15. Voice : Optional support for Survivable Remote Site Telephony support for local call processing in small enterprise branch offices for up to 240 IP phones.
16. Performance : Up to 1GB DRAM Up to 1GB Flash The maximum transmission unit (MTU) Up to 9576 bytes Throughput up to 1.2 Gbit/s .
17. 110/220 volts.
18. Warranty certified by Sis 98 or by OEM (original equipment manufacturer) .
19. Up to 115.2 Kbps for Console/Aux port with DDR capability.
20. Supports IPv6
View 2 Replies
View Related
Nov 15, 2012
I am using a 2851 router in mpls network. We had a power shut down activity recently and post to that i could not find any logs in the router.
View 4 Replies
View Related
Nov 12, 2012
I recently obtained a 2851 and have been battling this issue for a week now. An odd set of circumstances happen with the bootstrap startup process. If the router has loss of power or when reloaded; it fails to read the CF card and boots to rommon. I can tftp an image to it (tftpdnld -r) and IOS CAN read the flash card along with any saved configuration.In fact once in IOS, I can wr mem and print the hardware details of the CF card. Once I reload the router it goes to rommon, fails to open the flash, then sits until i tftp the image back. When the router load IOS, it also loads the startup config.I don't think it's a problem with the CF card as IOS can read it. I've tried formatting the card from IOS and from my pc as FAT, FAT16, FAT32, and NTFS - it didn't make a different. I updated the ROMMON to allow for USB booting but haven't purchased a USB Drive yet for testing. The upgrade didn't resolve this issue either. It almost seems like a firmware problem with the EPROM.
View 7 Replies
View Related
Jan 15, 2013
[URL]I ran across this on the cisco site and I wondering if it was possiable with two 2851's? The part that is most interesting to me is this part of the config (this looks like what allows the use of the y-cable)
redundancy
#
mode y-cable
how to have a redundant border router with a T1
View 2 Replies
View Related
