I have a new 3925 router and it came with 1 VWIC3-4MFT-T1/E1 card installed. I added a 2nd one and although it shows up in inventory, the interfaces do not show up in configuration in any form, interface or controllers. I used to just install a card and it would be recognized, is that no longer supported and is it platform specific or IOS specific?
View 3 RepliesWe currently installed a 100Mbps fiber line with Ethernet hand-off. I purchased a Cisco 3925 ISR to be the gateway for this connection. I am not going to use it for any security purposes. I have an ASA5520 that will do that work. Right now I am currently just trying to get the router online.
I know the following
Laptop <--->GB 0/1((()))GB0/0<---->Ethern
et handoff from ISP.
I can ping and SSH to the outside interface of the router from outside the network. I can also ping and SSH to the router from the laptop that is directly attached to the routers GB0/1 port. From the Router's CLI I can ping IP addresses on the internet. From the laptop I can not. I can not access the internet through the router though. Here is my config.Building configuration...
Current configuration : 3724 bytes!! Last configuration change at 02:17:03 UTC Tue Jan 15 2013 by ggsis! NVRAM config last updated at 02:09:33 UTC Tue Jan 15 2013 by ggsis! NVRAM config last updated at 02:09:33 UTC Tue Jan 15 2013 by ggsisversion 15.1service timestamps debug datetime msecservice timestamps log datetime msecno service password-encryption!hostname XXXNAMEXXX!boot-start-markerboot-end-marker!!logging buffered 51200 warningsenable secret 4 XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX!no aaa new-modelmemory-size iomem 20!no ipv6 cefip source-routeip cef!!!!!no ip domain lookupip domain name XXXXXXXXXXXXXXDomainXXXXXXXXXXXmultilink bundle-name authenticated!!crypto pki token default removal timeout 0!crypto pki trustpoint TP-self-signed-XXXXXXXXXXXXXXXXenrollment selfsignedsubject-name cn=IOS-Self-Signed-Certificate-XXXXXXXXXXXXXrevocation-check nonersakeypair TP-self-signed-XXXXXXXXXXXXXX!!crypto pki certificate chain TP-self-signed-XXXXXXXXXXXXXXcertificate self-signed
[code]...
I have a new 3925 ISR G2 router with the universal IOS, 256kb flash in CF0, 1gb flash in CF1. When the router boots it prompts to enter initial config. Whether I say yes or no, enter the appropriate info, "write memory", and reload it comes up with a blank config. I've checked the config-register (2142), copied the start up-config to nvram:, flash0:, and flash1: but nothing works.
View 2 Replies View RelatedI am currently trying to setup a GRE tunnel on a cisco 861. As part of a configuration template provide by an outside source I am recommended to use a sub-interface on the router but the recommended configuration does not work.
View 1 Replies View RelatedI've got a question concerning the configuration of multiple AP manager interfaces on -for example- a cisco WLC 2504. I've read the configuration guide but I'm not sure whether this is the way the protocol works. Say I want to distribute AP's (and traffic) across various AP Manager interfaces on the WLC. I would configure the following:
Create one management interface (which will automatically also be an AP-Manager interface)Configure 1 (or more) Seperate ap-manager interfaces, assign them to a port number, and select "Enable dynamic AP Management". VLAN ID's will be the same.Create a WLAN and configure it's interface to "management" Is it correct if I state that the LWAPP protocol takes care of the discovery from the Access Point and sends information about the available AP-manager interfaces back to the AP and the AP knows which ap-manager interfaces are available, connecting to the least loaded one?
I've got a new 5508 wireless lan controller and can ping the ip address of the management interface, but can't access the GUI at the management interface's ip address. I can access the GUI on the service-port interface. No static routes in the controller; trunk appears to be set up correctly.
View 5 Replies View RelatedI have several switches that don't show the key cryptext in their config when I do a show run.What would cause this? I am generating self-signed keys via "crypto key generate RSA"
View 2 Replies View RelatedWe have Cisco 2851 Router part code CISCO2851-SEC/K9 facing issue while set peer configuration, issue description below.
Issue:We are facing the problem while configuring set peer as when we try to this we face error like 'unable to set peer.maximum numbwe of peer (40)exceeded'
We suspected the IOS issue hence we have gone for IOS upgrade for this Router but this error is still coming while configuring set peer.
Previous IOS: c2800nm-advsecurityk9-mz.124-15.T7.bin New IOS:c2800nm-advsecurityk9-mz.124-24.T7.bin
We are attaching here the snap shot of error that is coming while configuring the Router with set peer command along with show tech of the Router to understand this case brief.
I have reconfigured the FEX numbers attached to a Nexus 5548 running on NXOS5.2 If I do show running-config the interfaces are not there anymore. But if I do show startup-config the old Fex interfaces still shows up. I did try write erase then saved the running-config and its still there.
View 1 Replies View RelatedMy cisco works LMS3.2 is not showing recent configuration of my Cisco devices. also it dont show any change report on last 24 hours or even if i select x number of day, looks like its not saving any changes made on devices.
today i logged in and cisco ASA was showing this in status as well Configuration Last Archived Time May 03 2012 11:27:46 EDT on checking i could see it is same date when cisco ASA was added in cisco works. do i need to click some where for auto update configuration changes and latest confoguration in cisco works setting?
my computer is a dell dimension 1100, with a Linksys WMP54G wifi card, running vista home basic.In the wifi thing in the notification area, it shows two wireless networks, One is my normal SSID (Lower Net), and one is "Unidentified network". They are both on one wireless connection (Wireless Network Connection 3). When i try to go on the internet, it says i'm not connected. i tried disconnecting from the unidentified network, but that disconnects me from lower net too.
View 13 Replies View RelatedI need 3925 router that support BGP as well as IPSEC VPN. is this correct part number i ordered? CISCO3925-SEC/K9. Its always hard to understand Cisco licensing, specially new one. will above package will have router wth ipbasek9+seck9?
View 4 Replies View RelatedI have one router 3925 equipment DIRECTLY connected to the Router that needs to be accessed by telnet port 23.
Please find the attached config details.
I have spend half day to look up this question in cisco official web site, but get nothing . Any infomation about vpn performance of 3925 router？Produce : cisco 3925 ( Cisco 3925 Security Bundle w/SEC license PAK )Question is , how much ipsec vpn tunnels can be carried as a vpn server of this bundle ? if more licenses may be bought, how much most tunnels can be held？
View 5 Replies View RelatedI have a Cisco 3925 router running IOS 15.2 I am trying to configure IP SLA on it. The configuration is supposed to be what is pasted below. but the CLI is rejecting the commands.Its taking oly the "ip sla responder" command after that if I enter "ip sla 1083180034" command it says invalid input. [code]
View 5 Replies View Relatedhow to setup natting on a 3925 router.
View 1 Replies View RelatedI have a question regarding the 3925 router. In the past on my old 3660's, in order to add a new line to an ACL, I would have to remove the entire ACL and readd it when adding new ACL lines to the list. Is this required on the 3925's, or is it like the ASA 5520's where you can just add an ACL any 'ol time without having to remove/add the entire ACL list?
View 2 Replies View Relatedwe are configuring a ras on 3925 router with e1 controller. when we connect the e1 controller to pbx we got on pbx a no frame alarm (detailed error is that we have nfas but we do not have cas). what could be the error? do the router need dsp to have a framed e1?
View 1 Replies View Relatedi said in the title i have forgot my password for my cisco3925 rourtor and how to reset my password
View 3 Replies View Relatedchecked all the recovery doc, however, there is no one specific for 3900 series router
View 2 Replies View RelatedI have cisco router 3925 and i add install HWIC-4ESW, as i sew on cisco documents you can hot swap the hwic without reload the router but i it's not working at all. How to do it ?
View 1 Replies View RelatedI am trying to set up a redundant OSPF setup and I am seeing behavior I don't quite understand. At the main office I have two routers, a 3825 connected via full DS3 to the MPLS cloud, and a 3925 connected to the Internet for VPN backup.There are nine branches, but I am only going to talk about three. The three branches all connect together as well as having their own MPLS connections to the cloud. They are all 2821 routers with a 4.5 Mbps multilink interface into the cloud (three T1's). One of the branches has a backup IPSec/GRE Internet connection that I want any of them to be able to use in case of an MPLS problem (which there have been many lately, sometimes involving all of them going down at the same time). The connection into MPLS uses Inter-area OSPF with the provider. The Tunnel connection is also using IA OSPF (the main office is area 0 and this cluster of branches are all on area 100).
OSPF seems to be behaving oddly. At the main office, on the 3825 with the "backup" shut off, if I do "show ip route 10.51.0.0" it shows this output: [code]If the metric before was 24, why would it put in a route with a metric of 53 now? What's worse is that the branches all think they should connect over the MPLS and the main office sends everything over the VPN. It works, but I don't really want asymetric routing! I have included some configs as well... those which I consider relevant. I am including a diagram that has more on it than is relevant, but what I referenced is here (and yes, spanning-tree has been properly configured on the red fiber connections with the connection between FEC2960 and Hl2960 blocking, but try to ignore the LAN stuff because this is in a transitional phase right now anyway).
I want to connect my clients from the Windows WS to a VPN Tunnel using 3925 router w/o Cisco VPN client. Is there the way to use native IPSec client on Windows XP or Windows 7?
View 1 Replies View RelatedI need to install an ATM module in a 3925 router. I would like to know if this card is that I have to buy with the transceiver(SFP)?
Will use a fiber cable LC LC singlemode fiber optic.
Module: NM-1A-OC3-POM
Transceiver :SFP-OC3-IR1
Monitoring H.323? I've got a 3925 running15.1(3)T with 9 PRI's. Because of our volume, syslogging is not the desired solution. We want something that we can potentially graph over an 8 hour period, so while the RTMT is accurate, either it won't store the data for 8 hours, or we aren't using it correctly (plus, mgmt may want access to the stats/graphs, and we're not keen on granting them access). So far, we've used: [code] None of these seem to accurately portray utilization. cdsp Active Channels seems to get the closest, so perhaps I have to tweak it a little bit, but so far, nothing accurate.
View 3 Replies View RelatedI have a network architecture like the one HERE but with alot more spokes (32). Would my cisco 3925 be able to support so many crypto maps?
View 2 Replies View RelatedRecently fitted 2 3925 routers on a WAN Mulitlink (2 * 2Mb) which has been working reasonably well but have noticed CRC's and intremitteny up/downs on E1 links. This could be due to issues with Microwave links but on checking nothing stands out on these - no errors or traps form radios.
Anyway taing a closer look at E1 lines and had some questions:-
Microwave radios E1 circuits are set to UNFRAMED, router interfaces set to NO-CRC4, didnt think this was the same?
E1 card are VWIC3-2MFT-T1/E1 and also noticed the following:-
no network-clock-participate wic 0(same for 1 and 2), my card are in slot 0 and 1.
I see no slips etc on E1 controllers .
I was wondering if the NM-1HSSI is supported on the cisco 3925. documentation seems to include only till 3800 series but can't find if it's supported or is there an alternative option for 3925.
View 6 Replies View RelatedI have a new Cisco 3925 router. I have 2 network segments 10.0.1.X with net mask 255.255.255.0 and 10.0.2.x woith netmask 255.255.255.0. I have an internet gateway router at 10.0.1.21. I have set GBethernet 0/0 to 10.0.1.1 / 255.255.255.0 and GBethernet 0/1 to 10.0.2.1 / 255.255.255.0. I have set a static route 0.0.0.0 / 0.0.0.0 to 10.0.1.21 for gateway of last resort.
When I setup a workstation on the 10.0.2.X segment at 10.0.2.100 wirh a gateway of 10.0.2.1, I can ping 10.0.2.1 and 10.0.1.1 but can not ping anything else on the 10.0.1.X network or on the internet. When I am connected to the console port on the router I can ping 10.0.1.1 and 10.0.2.1 and 10.0.1.21 and any address in the internet but I can not ping 10.0.2.100.
When I am on a network connected to the 10.0.1.x network af 10.0.1.100 I can ping 10.0.1.1 and 10.0.2.1 and 10.0.1.21 and anywhere on the internet but can not ping 10.0.2.100 or any other address on the 10.0.2.x network other than 10.0.2.1. What Do I need to do on the 3925 to get to all address on each segment and to get to the 10.0.1.21 gateway from the 10.0.2.x addresses?
I am using a Cisco 3925 router and attempting to install an EHWIC card with no luck. The card I am trying to install is EHWIC-D-8ESG.
I have powered down the router, inserted the card into the proper slot and my router doesn't seem to recognize the new card. Is there a command I need to enter to enable the card?
What the maximum concurrent users you can have on a Cisco 3925 for :-
1) Site to Site VPN using IPSEC tunnels
2) GRE tunnel sIf I have 90 users on a single GRE tunnel with 50mb Internet pipe using fat clients will this work ?
To have GRE tunnel support in a Cisco3925 do I need any specific license (DATA, SEC, etc) or it is include in the UNIVERSAL IOS?
View 1 Replies View RelatedI'm looking to utilize one of my 3925's to create a LAN-LAN IPsec VPN tunnel with another site.
I was under the impression that I needed to get a securityk9 license installed and then I would be good to go. I got a temporary 60 day trial license and successfully installed it, but none of the commands that I need to create the tunnel are showing up for me.
I'm trying to use the "crypto isakmp" command, but that is not showing up: Router(config)#crypto ? ca Certification authority key Long term key operations pki Public Key components
Here's my show license:
Index 2 Feature: securityk9
Period left: 633 weeks 4 days
Period Used: 0 minute 0 second
License Type: Evaluation
License State: Active, Not in Use, EULA accepted
License Count: Non-Counted
License Priority: Low