Cisco :: Switches Not Showing Cryptext Key In Configuration

May 15, 2012

I have several switches that don't show the key cryptext in their config when I do a show run.What would cause this? I am generating self-signed keys via "crypto key generate RSA"

View 2 Replies


ADVERTISEMENT

Cisco WAN :: 3925 - Interfaces Are Not Showing In Configuration

Aug 6, 2012

I have a new 3925 router and it came with 1 VWIC3-4MFT-T1/E1 card installed. I added a 2nd one and although it shows up in inventory, the interfaces do not show up in configuration in any form, interface or controllers. I used to just install a card and it would be recognized, is that no longer supported and is it platform specific or IOS specific?

View 3 Replies View Related

Cisco WAN :: 2851 Router Showing Error For Peer Set Configuration

May 28, 2012

We have Cisco 2851 Router part code  CISCO2851-SEC/K9 facing issue while set peer configuration, issue description  below.
 
Issue:We are facing the problem while configuring set peer as when we try to this we face error like 'unable to set peer.maximum numbwe of peer (40)exceeded'
 
We suspected the IOS issue hence we have gone for IOS upgrade for this Router but this error is still coming while configuring set peer.
 
Previous IOS: c2800nm-advsecurityk9-mz.124-15.T7.bin New IOS:c2800nm-advsecurityk9-mz.124-24.T7.bin
 
We are attaching here the snap shot of error that is coming while configuring the Router with set peer command along with show tech of the Router to understand this case brief.

View 1 Replies View Related

Cisco Switching/Routing :: 5548 - Removed Fex Still Showing Up In Startup-configuration

Jun 12, 2013

I have reconfigured the FEX numbers attached to a Nexus 5548 running on NXOS5.2  If I do show running-config the interfaces are not there anymore.  But if I do show startup-config the old Fex interfaces still shows up.  I did try write erase then saved the running-config and its still there.

View 1 Replies View Related

Cisco :: Ciscoworks LMS3.2 Not Showing Latest Configuration / Change Audit Report

Dec 19, 2012

My cisco works LMS3.2 is  not showing recent configuration of my Cisco devices. also it dont show any change report on last 24 hours or even if i select x number of day, looks like its not saving any changes made on devices.
 
today i logged in and cisco ASA was showing this in status as well Configuration Last Archived Time    May 03 2012 11:27:46 EDT  on checking i could see it is same date when cisco ASA was added in cisco works. do i need to click some where for auto update configuration changes and latest confoguration in cisco works setting?

View 1 Replies View Related

Cisco Switches :: SRW 2016 Not Showing Activity On Ports?

Apr 8, 2013

I have a Cisco / Linksys SRW 2016 switch, all was working fine. Powered off and powered back on a day later.Switch powered up and the system light lit.But non of the ports what had cables connected were active....If you connect a network cable to the switch and then a laptop / pc .. The computer knows that there is a connection, but only gives a 169 address. Presumably because the switch cannot get to my dhcp ?I have tried connecting a serial cable to the switch top see if I can see any error, but when running Hyper Terminal I only get the white screen and can not see any POST etc.As far as I under stand it is a straight through cable, do I need a null modem cable to console onto the switch?

View 1 Replies View Related

Routers / Switches :: Another Network Is Showing And Not Mine?

Feb 12, 2012

A friend was over with his lap top, since then I'm getting "sam's pc network",instead of my network, I can't seem to disable it, nor can the other devices in the house connect to it, the default is Sam's....

View 1 Replies View Related

Routers / Switches :: Computer Is Not Showing Static Ip?

Jan 17, 2011

I got a static ip from my isp. I set up my static ip manually through my linksy router. I need the static ip to connect to a private network for my new job but cant connect to that network. I went to whatsmyip and found that my old dynamic ip is still showing up externally, it looks like my ip4 is using the dynamic as a preferred. My question is do i need to manually change the network connection on my LAN and wireless connection under ipv4 to change it from automatically obtain TO use the following address and put in my static? And do I have to change the DNS also? I am on a home network with one desktop on vista home premium and laptop windows 7.

View 5 Replies View Related

Routers / Switches :: Lan Not Showing In Network Connection

Feb 4, 2011

i formatted my pc but after that lan is not showing in network connections

View 1 Replies View Related

Cisco Switching/Routing :: 3750 Stack Switches Not Showing Up

Jan 27, 2013

We have several stacks of 3750 switches where this problem is occurring.  All of the switches are running IOS version 12.2(50)SE3.  (Yes, I know it's old.)
 
We're seeing inconsistency in how the stack reports members when issuing the following commands:
 
sow switch
show version
show inventory
 
Not all members are showing up in the output of the "show version" and "show inventory" commands.  For example:
 
HUNTI-WV-WDAC03#sh switch
                                           H/W   Current
Switch#  Role   Mac Address     Priority Version  State
----------------------------------------------------------
1       Member 108c.cff2.ea00     15     0       Ready              
2       Member 8cb6.4f0a.a600     1      0       Ready              
*3       Master 8cb6.4f0a.9c00     1      0       Ready
(all three switches in stack are displayed)(code)

View 1 Replies View Related

Routers / Switches :: How To Get Device Names Showing On Asus

Dec 6, 2011

In asus router model rt-n10, there is a client list when you bring up 192.168.1.1 showing names of devices also mac addresses and ip addresses. How do I add names to the list so I know which devices are using what ip etc. I have tried the advanced settings in the router to see if I can do it this way , but no luck.

View 1 Replies View Related

Cisco Switches :: QoS Configuration On SRW2024 And SGE2000 SBS Switches

Jun 26, 2011

I have a Campus LAN setup which is layed out using Cisco SRW2024 and SGE2000 SB switches. On the LAN we are running various services. These are CCTV, VOIP(SIP), Public Address(multicasting) and Internet hotspots to various locations. I have attached a layout of the setup. A unique VLAN is setup for each of these services.The problem we have is that the PA audio is breaking up at intervals making the output distorted this is also happening for the SIP phones within the facility. Using the user guide we have tried to setup QoS on the system but we seem not to improve the services.

View 2 Replies View Related

Cisco Switches :: How To Erase All Configuration In ESW 500 Series Switches

Aug 21, 2011

How to erase or remove  configuration file from ESW 500 Series Switches?

View 2 Replies View Related

Cisco Switching/Routing :: WS-3750G-24TS - Switches Logs Showing CPU Errors

Oct 16, 2012

We have a stack of 4 Cisco WS-3750G-24TS with Sw  Version 12.2(52) SE and giving weird errors:-
  
-Traceback= 17211C8 16FA4C0 16FA4FC 18625E4 18608D4 286A850 283E6FC 282EDF4 2859BBC 1B2EDA8 1B25878
Oct 17 22:26:48 AEDT: %SNMP-3-CPUHOG: Processing GetBulk of lldpRemEntry.7
Oct 17 22:26:50 AEDT: %SYS-3-CPUHOG: Task is running for (2098)msecs, more than (2000)msecs (8/6),process = SNMP ENGINE.
-Traceback= 172108C 17211CC 16FA4C0 16FA4FC 18625E4 18608D4 286A850 283E6FC 282EDF4 2859BBC 1B2EDA8 1B25878
Oct 17 22:26:51 AEDT: %SNMP-3-CPUHOG: Processing GetBulk of lldpRemEntry.7
Oct 17 22:26:53 AEDT: %SNMP-3-CPUHOG: Processing GetBulk of lldpRemEntry.6
Oct 17 22:26:53 AEDT: %SYS-3-CPUHOG: Task is running for (2097)msecs, more than (2000)msecs (1/1),process = SNMP ENGINE.
 
What are these errors is this a bug in the IOS

View 1 Replies View Related

Cisco Switches :: SGE2010 - How To View Table Showing Which MAC Address Is Plugged Into Which Port On Switch

Jul 31, 2011

I volunteer at a school who just purchased two 48 port SGE2010 managed switches.  I am not a big fan of the web gui and was hoping to see the standard Cisco command prompt instead of the menu-type interface.
 
Is there a way to view the MAC table showing which MAC address is plugged into which port on the switch?  I have been fighting with the menu and the gui for a while now and do not see this anywhere.

View 5 Replies View Related

Routers / Switches :: Linksys Wrt54gs Config Page No Longer Showing Complete Info?

Oct 13, 2012

Signed onto pc as admin, logged into router with correct user name and password. No page in the browser based configuration displays the complete information for the page. Menus are missing as are option labels, etc. The last time I accessed the router (about a year ago) I didn't have this problem.

View 3 Replies View Related

Vista Showing Normal Wireless SSID Plus Showing Second Unidentified Network

Feb 5, 2011

my computer is a dell dimension 1100, with a Linksys WMP54G wifi card, running vista home basic.In the wifi thing in the notification area, it shows two wireless networks, One is my normal SSID (Lower Net), and one is "Unidentified network". They are both on one wireless connection (Wireless Network Connection 3). When i try to go on the internet, it says i'm not connected. i tried disconnecting from the unidentified network, but that disconnects me from lower net too.

View 13 Replies View Related

Cisco :: QOS Configuration On 3750 L3 Switches?

May 28, 2012

We have PC's that connect through the Siemens IP phones and back to the cisco 3750 which is connected to our core 6500 via L3. The phones use a voice VLAN and the PC's use another VLAN. The whole setup seems to work ok but I was just wondering if the QOS was configured correctly. Our current config on our 3750 switches are mls qos trust dscp on the port that connects to the phone and PC and mls qos trust dscp on the L3 links. The phones are configured for "QOS L2/L3"From the reading I've done so far it seems that any ports connected to a L2 device should be set to cos and not dscp?

View 16 Replies View Related

Cisco Switches :: SF302-08 Configuration

Apr 6, 2012

How do I make the following work with Cisco 302-08G ? I have a 4-port Cisco wireless/wired router that allows for a guest account. I also have Cisco SF302-08 that I bought so I could use its port/vlan mirroring capability. How should I configure the network, given the aforementioned equipment,  so that I can get a single point sniff.
 
Assume I have two wireless clients, one using the "regular" wireless SSID, and the other using the "guest" SSID.  I can see 192.168.1.x (regular SSID) and 192.168.169.x (guest ssid)  on the internet side (one the same physical cat5 of the wireless router. So far so good. But, I would like to use 302-08 to actually allow the guest SSID/network comm cable)unicate with the regular SSID/network. For example, if I ping 192.168.169.x from 192.168.1.x, I would like to see a response. Can I make them communicate properly with the 302-08 ?? if so, what do I need to do ?? (I will also have wired clients tied into the 302-08..so its important that it be the central sniffer point).

View 2 Replies View Related

Cisco Switches :: SG 300 Configuration Assistant

May 11, 2012

I'm having trouble in connecting a SG 300 switch with CCA v3.2. I have already connected the switch with CCA, however I can't see anything in my CCA's Front Panel and Topology view. Here is the view of my Front Panel view after I connect the switch ?

View 2 Replies View Related

Cisco Switches :: SG 200-50 VLAN Configuration

Aug 24, 2012

I'm adding it to an existing infastructure, with multiple VLANs.  I believe I have it set up correctly, however whenever I daisy-chain the switch in with the trunk ports, it's not passing the VLAN info correctly.  There's not a lot of configuguration involved, so I'm not quite sure where I might be going wrong.  I've attached a couple screenshots that show my trunk port configuration. 

View 3 Replies View Related

Cisco Switches :: SG 300-28p Vlan Configuration

May 2, 2013

I have been trying to setup vlans on a SG300-28p but they are not working. This is my setup: I want Switch1 to have ports 1-10 to access the DMZ, and 11-24 the LAN. Then i wan to add switch2-4 to extend the access to LAN.
 
i tested with cisco 2960 switches by just telling what ports whould have access to DMZ and LAN but the small business switches are different..

View 1 Replies View Related

Cisco Switches :: SF500-24p And CCA For Configuration

Feb 19, 2013

I am trying to get an SF500 in to CCA for configuration. I can find the device in CCA, and it prompts for a username and password, but it doesn't accept the u/p combo. I confirmed that the combo works when tel netting to it.
 
I have telnet, ssh, HTTP and HTTPS enabled on the switch, but the results are the same. On the console, it tells me that the the connection has been rejected. It appears as though CCA is also trying https, as it is rejecting that stating "credentials expected to be encrypted". Is the SF500 compatible with CCA? I've found nothing online to the contrary. I am using CCA version 3.2.1.

View 1 Replies View Related

Cisco Switches :: LAG Configuration On SG300 52 Switch?

Sep 10, 2011

I am having an issue with LAG configuration on a Cisco SG300 52 switch. I have connected four Ge ports on the switch to the four NICs of a Dell R710 Server on which I installed Windows Server 2008 R2. Without LAG configured, these ports would forward traffic to and from the Dell server fine.However, if I configure LAG on the ports with LACP enabled, then they would not forward any network traffic. Debugging shows that the ports are up but their forwarding status show N/A. Am I missing any configuration? Can I configure LAG on edgeports?

View 2 Replies View Related

Cisco Switches :: SG300-10 VLAN Configuration

Apr 22, 2012

Before I launch into this can I say that I am very much a novice with regards to Managed Switches and their configuration. I have the following equipment which I have connected to the switch: [code] All of the above are on subnet 255.255.255.0.All of the above communicate with each other during normal operation.Our client is connecting to the switch but his requirement is for his system to "see" the PLC Comms Card as follows:IP: 10.0.3.61 on Subnet 255.255.252.0 .
 
Using the Internet Explorer interface connection I have created an additional VLAN (ID 2) on Port 10 with the intention of using this as the connection to the client ( I assume there will be further settings required to route the PLC connection to this port) but every time I try to assign the IP and Subnet values and click "APPLY" the changes are not made and the connection appears to hang leading me to reboot the switch.I have connected to the switch via console and changed the mode to Layer 3.  I also assume that it is OK for the three pieces of equipment to remain on the default VLAN. How I should setup this VLAN and ultimately achieve my goal.

View 5 Replies View Related

Cisco Switches :: SG 300-10 And SF 300-08 Dropping Configuration After Reboot?

Jun 20, 2012

My company uses the SG 300-10 and SF 300-08 switches to deliver services to our customers. We have been using the upgraded firmware version 1.1.2.0. Our normal procedure is to configure the switches in house and upgrade the firmware before sending them out to the customers. The configurations are confirmed in house after the new firmware has been loaded. Recently we have had several of these switches lose the Vlan configuration that we setup. These incidents have occurred after power outages and scheduled reboots. We do not generally have to reboot our customer switches.

View 11 Replies View Related

Cisco :: Backup Of Configuration From Nexus Switches 5K And 7K

Dec 4, 2012

I'm busy on configuring the backup of the configuration from Nexus switches 5K and 7K.I have installed COPSSH on my windows server and try to confiugre the sftp credentials. [code] I have tested from the CLI from the switch and i have the issue but if i use the default vrf 'default' it works fine.How can i change the command sent by DCNM to the Nexus in order to specify vrf default and not vrf management ?

View 1 Replies View Related

Cisco Switches :: SGE2010P And SGE2000P LAG Configuration

Sep 19, 2011

I've got multiple SGE2000P & SGE2010P switches
 
Originally I was happy just set them all up in a stacked ring configuration. However I've become aware that my back bone fibre links are contantly pushed to their max.
 
So I've decided that I should change this configuration and unstack the switches and make them all stand-alone units. and I'll configure 2 cable LAG links between all my switches Theorically I should now get 2GIGs between each switch and to complete the ring in my network for redundancy I'll turn on Spanning tree.
 
However I've tested the speed and I just can not seem to get a LAG connection with 2 x 1gig cables to push more data than a single link 1gig link cable would.
 
My test enviroment(not using fibre optic cables just cat5e copper cabling):
4 x pc's(all gigabit network cards)
2 x sge2000p switches
PC1 ---(1G eth)---                                                                        /---(1G eth)--- PC2
[SGE2000P]===(LAG1 2x1G cables)===[SGE2000P]
PC3 ---(1G eth)---/                                                                        ---(1G eth)--- PC4
 
If I send files from PC1 & PC3 simultaneously to PC2 & PC4 They don't transfer faster than if I I just use a single 1GIG Link cable
 
looking at the LAG configuration it shows both cables are connected & the LAG looks like it's working. But it really doesn't seem to be running at the expected 2GIG?
 
The LAG fail over seems to work fine if I remove either of the 2 cables from the LAG the link continues to work. (sometimes it will drop a ping when removing or readding a LAG cable)

View 3 Replies View Related

Cisco Switches :: ESW 520 24 No HTTP Configuration Utility

May 26, 2011

I need to confure 3 ESW-520, 2 24 ports and 1 48 ports, connected in etherlink on the same vlan. One of the 24 ports and the 48 ports works perfectly, the other 24 ports it working, i can use it as a flat switch, i can also access from the console, but i can't access from the http configuration utility. I upgrade the firmware, and set the vlan 1, the one i'm using as the only management, but i can't access ti the default ip 192.168.10.2. It's the switch broken or i'm making some error?

View 2 Replies View Related

Cisco Switches :: SG-200-26 Access Port Configuration

Oct 31, 2012

I'm having troubles setting up a separate VLAN for wireless on a SG-200-26. My first question is why did Cisco not make the VLAN setup like they have all their other business class switches? Anyways, the Access and General modes on these SG class switches are throwing me for a loop.
 
Right now I just have one port (g10) on the SG-200 switch that needs to be in VLAN 6, which is our wireless VLAN. All other ports are in their default VLAN, which is 1.
 
Here's what I've done...
 
Configured port G1 (trunk to another switch) as the trunk port and Port G10 (attached to WAP) as a general port. All other ports stayed in their default configuration. This is what it looks like now...
 
Port     Mode     PVID     Operational VLANs
g1       Trunk     1            1U, 6T
g2       Trunk     1            1U

[Code]..... 
 
I'm pretty sure port G1 is configured correctly, but I have no idea about what port g10 should look like. Common sense tells me it should be an Access port and assign it to VLAN 6, but apparently you cannot tag the traffic within an Access port on SG switches, which makes it useless because how will other switches recognize what VLAN the packets are in? So the next logical mode would be General mode, which I put in VLAN 6. I switched that port from being 6U (untagged) to 6T (tagged), but neither seemed to work.
 
VLANs on SG switches, how port g10 should be configured for VLAN 6 traffic.

View 4 Replies View Related

Cisco Switches :: SF-300 Sh Running-configuration Output?

Oct 25, 2011

Would it be possible to change output style of "sh running-config" in SF-300 switches to Cisco IOS-like format (eg.: options related to the specific interface put together, add tabs) in the next release?

View 24 Replies View Related

Cisco :: SLM 2024 - Set Up Switches / VLAN Configuration?

Aug 13, 2012

I'm new to managed networking.  So I'm having trouble understanding how to set up my switches properly.  I have a closed network with about 20 switches and 2 IDF's.  No router, and no internet.  I have a SLM 2024 in want to have 4 ports set up with a VLAN.

I have another SLM2024 I want to be on the same VLAN some where else. Switch 1 uses port 24 GBIC as and uplink port to one of the IDF's.  Switch 2 uses ports 12 and 24 copper(LACP) to make a hop from another switch(ports 1 and 13 LACP)which inturn is connected to thesame IDF on port 24 GBIC.  How do I set up switch 1 ports 7,8,19,20?  Also, how do I set up switch 2 ports 7,8,19,20?

View 5 Replies View Related

Cisco :: RSTP Configuration - 14 Switches Interconnected In Ring?

Apr 2, 2013

I need to setup a layer 2 network consisting of 14 switches interconnected in a ring. Obviously, the design of 14 switches in a ring network is dumb, not here to debate that. Unfortunately, it HAS to be a ring. I've been researching the best way to configure RSTP for this. From everything I've read all I really need to do is configure Primary/Secondary root bridge in the center, and change the Maximum Age field to at least 16 seconds? From what I've read you want a minimum of 3 second buffer + 1 second for each hop due to message age being added by each switch hop?

View 8 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved