Cisco Wireless :: 2504 Bandwidth Of Capwap Tunnel
Dec 15, 2012
I'm looking at the spec sheet comparing Cisco WLCs and I see that the 2504 has a bandwidth max of 500mbps. Just to be clear, not all of the traffic from the APs goes through the WLC does it? In this setup, the APs would be plugged into a PoE switch as well as the WLC. The only traffic to WLC would be the CAPWAP tunnel, CleanAir info, etc right? All other traffic should just be handeld at the switch right?Also, does the 2504 licencing include CleanAir in the price?
View 17 Replies
ADVERTISEMENT
Jan 13, 2013
My QA team needs to test number of special connectivity scenarios where their wireless connection has a limited bandwidth.Ideally, I would like to provide them number of SSIDs each of which has different bandwidth limitation.But so far I did not find a way to apply any bandwidth limitations to my 2504 Wireless controller and the 3602E AP.QoS has only 4 pre-defined modes which can't be set to a specific limit.
View 10 Replies
View Related
May 14, 2013
I have a 2504 Controller (os version 7.0)with 7 access poins attached and with 2 vlans. one for regular users and another for gues users.
View 10 Replies
View Related
Jun 14, 2012
I found 20Mhz bandwidth enable option in 2504 controller.But what about 40 Mhz .The access points(1142) are dual band...I hope it should support in 2504 controller also.If there is no option of 40Mhz
View 2 Replies
View Related
Feb 26, 2013
I'm attempting to set up (for testing purposes) a 2nd 'guest' SSID on an internal WLC (WLC-A), and terminate it in a DMZ on an anchor controller (WLC-B). We already have a guest SSID originating on WLC-A and terminating on WLC-B though. Is it possible to originate a 2nd guest SSID on WLC-A?
WLC-A - 2504 (7.2.x)
WLC-B - 5508 (7.2.x)
The problem I'm seeing is I'm getting no DHCP address assigned on the test SSID. If I statically assign IP information I still have no connectivity. It's as if the EoIP tunnel for the 2nd test SSID isn't functional.
View 2 Replies
View Related
May 25, 2013
does the cisco wlc 2504 (software release 7.4) support QoS per-user bandwidth contracts ? I only can see the default QoS profiles (gold, platinum...) i can't see the per-user bandwidth contract to modify it. shoud it be activated ?
View 3 Replies
View Related
Feb 28, 2010
We have point to point metro ether net link terminating on 7204VXR router.On this point to point link we are configuring GRE over ip sec. Problem is when the traffic exceeding 8mbps we started getting packet drops. from the Cisco documentation it seems the tunnel bandwidth is by default 8mbps and there is parameter like Inherit/receive but those actually not change the tunnel interface bandwidth.If we just give tunnel bandwidth with bandwidth mentioned it allows me to give option of 100mbps but again the tunnel interface bandwidth remains 8mbpos only and probably that 100mbps is useful only for routing decisions.
i am using advance security 12.4.15T12 image. Whether this is a limitation or any other way to go beyond 8mbps for the tunnel interface (7204VXR-NPEG1 processor)
View 18 Replies
View Related
Jun 10, 2013
We have two Cisco 2811 Routers setup with a GRE tunnel that we would like to constrain the bandwidth on to replicate a satellite connectinon of 400 kbits. We tried the bandwidth command 400, but from what I understand that is only for routing metrics and not actual speed of the interface.
View 5 Replies
View Related
May 13, 2011
I have a Cisco 1941 router with the Security license running IOS c1900-universalk9-mz.SPA.151-4.M.bin. Is there a "tunnel bandwidth" command like with routers that have the Advanced IP Services license? My concern is being able to adjust the bandwidth to a value greater than 8 Mbps...
View 3 Replies
View Related
May 19, 2011
We have a major poblem going on with our VPN router.We have a 7206vxr router which has an mGRE tunnel forming EIGRP neighbourship with about 800 remote locations using GRE over IPsec.
We have a problem where the EIGRP neighbourship keeps flapping intermittently and this happens to 30-40 locations at one time and very frequently.What I noticed was that the GRE tunnel transmit bandwidth was showing as 8 Mbps. I guess there is an option to change it.Will this 8 Mbps limit cause any issues of EIGRP neighbourship flaps and will increasing the bandwidth useful.
We are also seeing output drops on the tunnel interface.
pcvpnstore#sh int tu0Tunnel0 is up, line protocol is up Hardware is Tunnel Internet address is 10.254.254.254/16 MTU 17912 bytes, BW 30000 Kbit/sec, DLY 50000 usec, reliability 255/255, txload 244/255, rxload 110/255 Encapsulation TUNNEL, loopback not set Keepalive not set Tunnel source x.x.x.x (GigabitEthernet0/2) Tunnel protocol/transport multi-GRE/IP Key 0x328CDF, sequencing disabled Checksumming of packets disabled Tunnel TTL 255 Tunnel transport MTU 1472 bytes Tunnel transmit bandwidth 8000 (kbps) Tunnel receive bandwidth 8000 (kbps) Tunnel protection via IPSec (profile "dmvpn") Last input 00:00:00, output never, output hang never Last clearing of "show interface" counters 00:17:06 Input queue: 0/800/0/0 (size/max/drops/flushes); Total output drops: 732
View 9 Replies
View Related
Sep 8, 2011
We have a Cisco ASA 5520 supporting multiple VPNs - both remote-access and Lan-to-Lan. We would like to monitor the bandwidth utilization of the IPSec Lan-to-Lan tunnels.
View 3 Replies
View Related
Apr 23, 2012
So in our DMVPN network, we have this Cisco 3845 hub router that is connected via a DS3 to the Internet, and our spoke sites usually have a broadband connection that typically have a maximum of 1Mbps upload capacity. We are getting ready to add a few more sites to our network that are connected to the Internet with 10Mbps upload speeds (and 50Mbps download). Spoke site routers are usually 800 series ISRs. We have seen spikes of 8-10Mbps on the hub router so far. So the question is that a site with 10Mbps upload speed transmit to the full capacity over a DMVPN tunnel or is it limited by other factors? What are those factors?
View 4 Replies
View Related
Mar 3, 2013
We setup some new CAPWAP AP 3602E in the network and configure the DHCP server option 43 , but the WLCs still cannot detect the APs , Do you know if there any new way to troubleshooting?
WLC: 5508 version: 7.2.103.0
SW:3750E
AP: AIR-CAP3602E-C-K9
View 16 Replies
View Related
Feb 1, 2011
I´m looking to a project where we want to start using Autonomous AP with possibility to change to controller based on near future.
Will Cisco Aironet 1040 Series Access Points allow us to change from IOS to CAPWAP when needed? I read some posts about the oposite process (CAPWAP to IOS) so I think it´s possible on both way. Can some one confirm this to me?
View 5 Replies
View Related
Feb 9, 2012
We have had several APs disassociating from our controllers. The alerts say, Message: Access Point 'AP-xxxxx' associated to controller '10.x.x.x' on port number '0'. Reason for association 'Dot11g Mode Change. I have read several posts that point out that you should have QoS implemented to prioritize the CAPWAP traffic. I'd like to know if someone has implemented QoS and whether it has been successful in stopping the APs from disassociating. And if it has been successful do you have any configuration examples for the ports attached to the AP and controller as well as the QoS configuration?
We have several sites with AP1142's and 3500's. We have 2 5508 controllers. We are broadcasting 2 SSIDs of which one is in HREAP mode and the other is in local mode. Each of our sites have MPLS circuits.
Here is an example I found on Cisco which I believe can be used for CAPWAP as long as you change the ports to 5246 & 5247 instead of 12222 & 12223.
Example Router Configurations #
This section contains router configuration examples to be used as guides when addressing CS6 remarking or LWAPP control traffic load.
#
This example uses LWAPP APs on the 192.168.101.0/24 subnet, and two WLCs with ap-managers at 192.168.60.11, and 192.168.62.11. (code)
View 2 Replies
View Related
Mar 28, 2012
I have an 1142 running capwap c1140-k9w8-tar.124-23c.JA4 that I am wanting to convert to an Autonomous AP.However, the AP does not seem to have an archive exec command to tftp downoad an new IOS.Is there another procedure that should be used ?
View 7 Replies
View Related
Nov 12, 2012
I have to prepare an 3600 Capwap AP for autonomous functionality!
The following image was downloaded: ap3g2-k9w7-tar.152-2.JA
The release notes say: Site-Survey Only Mode for 3600, 3500, and 1550 Access Points You can install Cisco IOS Release 15.2(2)JA on Cisco Aironet 3600 and 3500 Series access points and on 1550 series outdoor access points to perform site surveys. This release runs on these access points with limited functionality. You can manually adjust these settings on the site-survey access points:
• Channel on each radio
• Transmit power on each radio
• Enable and disable the radios
• Manually set basic and supported transmit rates
• Enable advertised cell power in beacons to client to enable DTPC for doing active surveys
• Enable and disable SSID broadcast in beacons
• Enable open authentication
My Question is: Where can i find a instruction for downgrading an AIR-CAP3602i to Autonomous 3600 AP? Is it complicate to get the AP running, or what do i need for "downgrading"?
View 4 Replies
View Related
May 9, 2012
I am trying to configure two AP-management interfaces to accept CAPWAP on different ports using the option "Enable Dynamic AP Management". One of them uses public ip address. However, I getting the message "Ignoring discovery request received on non-management interface ..." on this.
The controller is 5508.
View 4 Replies
View Related
Apr 10, 2013
I have a wireless network running with Controller WISM2 and I also have a NCS.I want to know if there is any way to look of individual log of CAPWAP and LAPWAP Access Points. It is better if I can see it through NCS.
View 1 Replies
View Related
Jul 10, 2011
I am facing this particular issue while providing Cisco unified Wireless solution to the customer. We are having CAPWAP 1252 APs controlled by WLC.
Scenario: 50 persons sitting in a hall with closely packed chairs using wireless simultaneously. Wireless access provided by patch antenna at a height of 11m from the user. As one AP can server 25 users, 2 APs are placed with antenna directions facing the compact users. Each users gets very good signal from these two APs.
Whether there will be serious interference and client association issues in this scenario? once one AP associates 25 clients, whether other 25 clients associate completely to other AP?
View 3 Replies
View Related
Mar 10, 2013
I understand that Cisco *wants* the APs to be directly connected to the new 3850.I have a few questions. Unfortunately, I think I know the answers. I just want to confirm.
a. When MA/MC is enabled on the 3850, does the 3850 start intercepting *all* CAPWAP packets it sees (much like CDP)? Even non-Cisco CAPWAP packets?
b. If I have a WLC 5500 upstream from the 3850, would APs hanging off a downstream 2960 be able to register to the 5500 through the 3850 when the 3850 is NOT in MA/MC mode?
c. If I have a WLC 5500 upstream from the 3850, would APs hanging off a downstream 2960 be able to register to the 5500 through the 3850 when the 3850 IS in MA/MC mode?
What I'm afraid of is:
a. yes, yes
b. yes
c. no
From the Q&A page:Q. Does the Cisco Catalyst 3850 support indirectly connected access points?A. No. The Cisco Catalyst 3850 switch will always terminate the CAPWAP tunnel locally. Pass-through mode or indirectly connected access point is not supported at this time.
View 2 Replies
View Related
Jan 6, 2011
I would like to confirm if it is possible to downgrade AP 1042 from CAPWAP to autonomous? I want to buy the AP model AIR-LAP1042N-A-K9. But i don't sure if in the future it could support this feature.
View 9 Replies
View Related
Jul 10, 2012
Clarify some points with capwap implementation, does all data and control traffic tunneled back to the controller and switching packets to the specific vlan will be done by the controller? so if i have 5508 controller, its maximum throughput will be 8 gbps (local mode AP), provided i have done LAG on all its ports to the LAN switch?
View 2 Replies
View Related
Nov 8, 2011
The following messages are filling up my syslog.
*spamApTask0: Nov 09 15:59:29.071: %LOG-3-Q_IND: capwap_ac_reassembly.c:652 Unable to store capwap fragment from 88:f0:77:b6:fd:00.
*spamApTask3: Nov 09 15:59:27.616: %CAPWAP-3-REASSEM_SPACE: capwap_ac_reassembly.c:652 Unable to store capwap fragment from 88:f0:77:b6:fd:00.
What could be causing it? I am using 1524 APs in a Mesh environment with a WLC 5508 (7.0.116.0) which is connected to a H3C switched network.
The MAC addresses above are from my MAPs and I don't think I am getting it from the RAPs.
View 1 Replies
View Related
Mar 20, 2013
Can I convert a standalone 1600 access point to a CAPWAP based AP when I choose to deploy a WLC later?Cant see any literature on cisco.com that is specific to the 1600 APs
View 1 Replies
View Related
Jul 12, 2012
Is Aironet 1260 good for indoor LWAP or CAPWAP environment? Do we need external antenna for the Aironet 1260 access point when using it indoor?
View 1 Replies
View Related
Jun 22, 2011
I have some challenges with a VPN config I recently setup for a client.I have at the HO the following:
- 1800 router
- Avaya phones and Gateway
- 1MB radio internet access
At the BO(branch office), i have:
- 871 Router
- Avaya phones
- 256k internet bandwidth
The only reason we setup the VPN in the first place was for the phones at the BO to be able to connect to the gateway at the HO and also able to make calls and receive calls as if the phones were at the HO.The phones at the BO successfully register to the HO, but are unable to recieve calls and dial out. Everytime I try to make a call, the phone displays a "connecting..." message. [code]
View 2 Replies
View Related
Sep 3, 2012
I want to know the CAPWAP protocol.
View 1 Replies
View Related
Sep 9, 2011
We have 1 mpbs bandwidth line, but most of the time we are getting only 300-500 kpbs download speed, i want to send statistics report to our ISP, what will be best procedure to test the bandwidth report, i have checked in some websites like bandwidthplace and speedtest but these sites are not accurate, how to check the actual bandwidth we getting from ISP against 1 Mbps. We have solarwinds monitoring tool in this i have configured the WAN interface for 1 mbps
View 5 Replies
View Related
Jan 9, 2011
i have a 7201 router with NPE-G2. i have a design which i have the option to send all the traffic through a GRE tunnel or a L2TPV3 tunnel.which method is more CPU consumption ?
View 1 Replies
View Related
Sep 23, 2012
I'm in process of purchasing a new Cisco routers for our branches that will be used primary to enable IPSec virtual tunnel interfce with "tunnel mode ipsec ipv4". does the default IOS IP Base supports this feature? or i need to purchase DATA license or SECURITY license?
View 4 Replies
View Related
Oct 17, 2012
I am using a Cisco RV110W (Firmware 1.2.09) in a branch and I would like to create a VPN Tunnel to another site that has a Cisco RV042 (firmware v4.2.1.02)
What would be the correct Configuration? the current configuration I am using is
in the RV042 i am using
Check Enable
Local Group Setup
Local Security Gateway Type : IP Only
IP Address : RV042 Pulbic IP address
[Code].....
View 3 Replies
View Related
Jul 24, 2012
Environment :linksys wrt300n v1.1 which can have ddwrt-mega. Willing to tunnel all lan's outbound traffic through an ssh tunnel.
View 2 Replies
View Related
