Is there a way to configure the GIG 0 interface on the 1552E Access Points to 10 Meg Full Duplex? Currently they will only work in Auto/Auto
View 3 RepliesI would like to know why i can't configure to 100 full duplex one port from target follow: WS-X6724-SFP
View 2 Replies View RelatedI have the following configurations for switch to switch connectivety. sh int sh config int
2960 will not take full duplex setting.
Core switch
WS-C4506 cat4000-i9s-mz.122-25.EWA10.bin
FastEthernet5/8 is up, line protocol is up (connected)
[Cdoe]....
So I recently got a new computer today and it won't let me use my 100mbps of internet bandwidth. (Asus Sabertooth Z77 with an Intel 82579v gigabit lan controller) I noticed that at the LAN connection properties>Properties>Configure>Link Speed tab the 'Speed and Duplex' option was on Auto Negotiation and it was only accepting (or supporting) the 10mbps Full Duplex. When I switched it to 100mbps Full Duplex it would mark my connection icon with a red cross and when I clicked diagnose it said "Please connect your ethernet cable or your cable might be broken". So I tested my internet speed with that same cable on a different computer (laptop) and it worked with 40Mbps, so I don't think the cable is broken. Also I just recently downloaded some drivers but one was specifically for the Intel LAN controller but I'm a total noob for all of this computer stuff I don't know if it messed it up or something. Is it the motherboard that's not working correctly?
View 3 Replies View RelatedHowto set ports from WS-C2940-8TF-S to full- and half-duplex 100Mbit?
View 1 Replies View RelatedI have a Cisco aironet 1040.
On my Accespoint i have 2 vlans: 1 for my wifi phones and 1 for my network.Wifi Lan has the SSID LAN with WPA enterprise authentication to a radius server(ms server 2008).Wifi Phone has SSID PHONE and vlan 50 with local radius authentication.This Works all fine, Except when i enable AP for my wifi phones. When AP is enabled the authentication for my lan doesn’t go to my server but local.How do I configure my accesspoints so that the cisco phones use the local radius server with AP and my windows computers connect using the ms radius server?
If I change the network adapter settings to 100 Full Duplex, is there any changes that will take effect? even if we don't have Cisco switches in our network.
View 4 Replies View RelatedI have C3750X with C3KX-NM-10G, and have-T SFP in slot 3 ( means it is not in SFP+ slot ).I need to set speed&duplex hard to 100/Full, but if I do the link goes down. I have the same settings on the other side, only IOS version is different.I tried other speeds - 10 and 1000, but no one works with Full. When I change duplex to Auto it works fine.The reason why I am doing this on C3KX-NM-10G is because I need to use NetFlow and cannot use the chassis' copper port. At the moment the ports are connected through a copper patch cord, but in full production there will be a radio link in between that requires 100M/Full to be set hard.I am trying to search for any document that would describe this limitation, but cannot find any. Also port capabilities do not indicate duplex could not be set to full:
show interfaces g1/1/3 capabilities
GigabitEthernet1/1/3
Model: WS-C3750X-48P
Type: 10/100/1000BaseTX SFP
Speed: 10,100,1000,10000,auto
Duplex: half,full,auto
Trunk encap. type: 802.1Q,ISL
[code]....
3750G-12S-S.Problem description:I had a WS-3750G-12S-S in production with a defective fan tray and needed to change it.I faced to trouble with inter g1/0/1 on the new switch( it worked fine on the old).
Here the config for old switch:
interfacigabitEthernet1/0/1
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 111-113,278,790
switchpmode trunk
speed 100
[code]....
even if I configure speed nonegotiate that does not work.
I have 100 mbps fiber connection. I bought 320N today I bought 320N and here is the problem:
We have a switch in the building. I am getting connection via CAT5. So I choosed "Use as WAN Port" from Ethernet settings. There is not much you can do here. I just used PPPoE and connected internet without any problem. The problem is I am only getting 32mbps. When I connect CAT5 cable directly to my computer I am getting 92mbps.
Maybe WAG320N is not establishing a full duplex connection.
I have ip phones at the remote location that connect into the phone switch(it's a nortel cs1000 system) over the tunnel. Internal calls work just fine, however when somebody calls from the outside, or calls are made to the outside the connection is never finalized. Like if I call from my cell it rings the phones, but when I answer there is nothing but dead air.In the group policy for the tunnel, I gave the remote site FULL access to the phones vlan and vice versa...which obviously works since internal calls work fine. If I remove my group policy and give it the Default group policy which essentially gives that tunnel full access to everything since the tunnel is set to bypass interface ACLS, external calls work fine. So it's definitely related to the group policy.
The group policy is basicallyAllow remote site to X network/host on these ports no denies since it blocks whatever isn't specifically allowed. However since it can get the phone switch and it can get to the internet I'm not seeing why the calls aren't working.The only thing I can think of to try doing as well is remove the allow inbound traffic to bypass interface rules and treat it just like another vlan interface on the ASA. Create the rules on each interface for the remote site network etc and see if it works that way.
Can we force the Gigabit Ethernet port to be 1000 full duplex in Cisco Catalyst Express 500 series?
View 3 Replies View RelatedWe have a number of 1552e's deployed as RAP / MAPs, using a 5508 WLC. All those are working fine.I have a few requirements for an outdoor access point... not a RAP or MAP, but just a simple outdoor AP. I assume that if I use a 1552e for that requirement, I would place the mode in local, rather than in bridge mode, correct ? Also, a question on mac filtering. When setting up the mac filter, there is a drop down selection for "interface name". The radios seem to work fine with "none" selected, so I'm confused about what exactly that selection is doing. Is it simply a reference lable, or does it actually have a purpose?
View 2 Replies View RelatedI need to configure WPA or WPA2 authentication on cisco 1042N access points. But I believe that for this requirement I need to have either an internal or external RADIUS server, but my customer want to just a normal WPA/WPA2 authentication like what we configure on cisco WAP200 or WAP4410 accesspoints, is there any work arounds to configure WPA/WPA2 authentication in a simpler manner rather than configuring RADIUS server option?
View 2 Replies View RelatedI ran into a strange problem. When I want to change the ethernet0 interface of a Cisco 828 sdsl router, but there is no command to do that in the interface configuration mode (speed 100 and duplex full). A show interface gives 10MB half duplex and I want to change this.
This is the running config (a little censored):
!
!
interface Ethernet0
[Code].....
we have connected gig interface Ethernet on Cisco 2900 series router to mpls link connected to our corporate network ,the issue here is our router interface speed and duplex settings are set to auto negotiation.The interface is negotiating speed and duplex at 10 and half where the provider side interface is hard coded to 100 and full duplex.when we tried to hard code the settings on our router to match the provider the interface never come up.
View 4 Replies View RelatedI have autonegotiation disable on my interfcae what should be duplex setting on other end?
Router#sh run int Gi0/3/0
Building configuration...
Current configuration : 334 bytes(code)
Question about cisco 2504 wireless controller, is it support cisco 1552E outdoor access point? If NO provide me the correct series/model.
View 9 Replies View RelatedA 1552E has a temperature gauge sensor connected to its power over Ethernet port. the port status shows line protocol as down.The cable from 1552 to the sensor has been changed twice. We can see the 1552E gig1 interface is at 1000full duplex. Is there any chance the speed is causing the problem here. it seems the 1552E doesn't allow to set different speed & remains on 1000.
View 2 Replies View RelatedI had insatalled the ACS 5.2 on Vmware . As per my requirement i need to configure a user to restricted privilege so that he should be able to execute only the below commands on the switch .
-Show ver
-Show interfaces
-Show ip Interface Brief
-Configure terminal
-Interface <interface name >
-Shutdown
-No shutdown
The users should not be authorized to execute any other commands than above listed one .After the configuration i was not able to restrict the config mode commands . Once the user is authoized for Configure terminal access he will have full access on the device. How to configure the command set only to allow interface access and he should be able to apply Shutdown and No shutdown command .
Our ASA 5510 was configured with a public interface, a DMZ interface, and a private interface. I have a remote access VPN using AnyConnect client and LDAP authentication for Active Directory. We are changing ISP (groan!), which means all new public IP addresses. The new circuit is installed, so I have a second public interface (same security level as the first public interface, wholly different IP address range) enabled on the ASA. I hope to transition whatever I can, which means get the VPN access through either public interface. Can I just enable client access on the second public interface at the Anyconnect Connection Profiles tab in ASDM? That seems too simple. Can they share the one address pool?
View 1 Replies View RelatedI am adding a second external connection to an existing system on an ASA 5510 with ASA V8.2 and ASDM 6.4. I added the new WAN using an other interface (newwan).
The intention is to route most internet traffic over the new route/interface (newwan) but keep our existing VPNs using the former interface (outside).
I used the ASDM GUI to make the changes and most of it works.ie. The default route goes via (newwan). Outgoing VPNs of a site to site nature use the previous route via (outside) as they now have static routes to achieve this.
The only problem is that incomming Remote Access Anyconnect VPNs are not working. I set the default static route to use the new interface (newwan) and the default tunneled route to be via (outside) but this is the point is goes wrong....
I can no longer ping the outside IP address from an external location. It seems the outside interface does not send traffic back to the - outside interface (or at least that's where I think the problem lies). How do I force replies to the incomming VPN remote traffic from unknown IPs to go back out on the outside interface?
The only change I need to make to get everything working on the outside interface again is to make the Default Static route use the outside interface. Which puts all the internet traffic back on the original (outside) connection.
I have an issue where our ASA 5520 is impacting upload (from LAN to internet) speed. We have a 100Mbps SDSL internet link and only see around 45-50 Mbps on the upload when going via the firewall, download is around 90+ Mbps so that is acceptable. I have tested a laptop connected directly to the internet router and that give near on the 100Mbps up and down speeds, but if I put that laptop on the LAN or directly onto the firewall interface I only see 90Mbps down and 45Mbps up. I have check that the interface speeds/duplex on the firewall, switch and laptop are correct and also checked there are no errors on the ports. I also turned off the IPS and that made no difference. In addition I have checked the CPU during download/upload (max): CPU utilization for 5 seconds = 9%; 1 minute: 3%; 5 minutes: 1%
In theory the 5520 should be able to cope with this throughput:
Cisco ASA 5500 Series Model/License: 5520
Maximum firewall throughput (Mbps): 450 Mbps
Maximum firewall connections: 280,000
[Code].....
We have a Cisco ASA5505 here that provides DHCP and routing to all our devices in our network. We also have a few other switches and wireless access points connected directly to the back of the ASA5505.For the past year all the wireless network signals has been working fine however starting last month, none of the wireless access points (we have three WRT54G) would allow proper connection (dropping connection, slow internet).I thought this maybe all THREE wireless access points are toast/bricked. So i went out and bought brand new Netgear WN604 and even with the new WAP i'm having same connectivity issues (really slow internet).When hardwired directly to the switches we get BLAZING fast internet & connectivity, no issues.
I called CISCO TAC and they automatically said "our ASA5505 is fine, it has to be your wireless access points" not working properly. I explained to them that i also purchased two brand new access points and they are doing the samething now, how can that be?
I've had some long standing issues that I've tried various things to fix. I have two WAP4410N access points set up at a smaller sister company. Wireless clients (laptops) are not receiving DHCP assigned IP addresses. If I type in an IP manually, it works fine.The sister company has a point to point T-1 connection to our main building. Our main building has the DHCP server. The router on the sister company end is configured as the DHCP relay.
I've upgraded the firmware three different times in the past to hopefully resolve the issue, but no luck. Just today, on one of the WAP4410N's, I upgraded to the 2.0.6.1 firmware (backing up config, reset to factory default, upgraded firmware, reset factory default again, restored config). After the first reset to factory defaults, the Access Point itself picked up a DHCP address from the server, and I verified this in the DHCP console on the server, so I know that the DHCP relay is working. However, my laptop would not get a DHCP address when connecting wirelessly through that access point. It is a Windows 7 Enterprise laptop. I also could not get a DHCP IP with my iPhone connecting to wireless, to rule out specific issues with just a laptop.I have the DHCP lease times for the subnet that these WAP4410Ns are on set to 2 hours.
To put a cherry on top, there is one laptop that stays in a lab area at all times, connecting wirelessly, and it DOES get a DHCP IP address (I can see in the DHCP console that the lease for this laptop continually renews as needed). I do remember on initial config when I couldn't get it to work, that I did a manual set up, gained connection, then switched it to DHCP...but that doesn't work for any other laptop.Why would the access points get DHCP address, but not anything connecting to the Access Points?
Using WISM with 7.0.220 and 1240 and 3502 APs. Just found that some of our 3502 AP didn't enbale their clean air and CDP when installed. This only happened on a few new APs. But the area these APs where we seem to have had a few problems with PCs. The only PCs effected where Computer On Wheels (COWs), Dell 780 Desktop with a Cisco Wireless Card.
Using an interl wireless card and others in thes areas worked.Once I enabled the CDP and Clean Air, the COWs worked.My question is with the APs not having CDP enabled, could this affect the cisco wirelss card in the COWs?
At my school we have a lot of access points, but sometimes the computer use the wrong access point. How can I solve that? Is there a program for switching access point?
View 8 Replies View RelatedBTW the halls are next to each other.The house and the 3 halls are in the vicinity however not attached together(i.e. wall to wall). The distance between the house and the first hall is approx 1 road width distance.ISP is Virgin and the internet was installed this year hence has the latest Virgin Home Hub.I am aware that i probably require 3 wireless access points (1 for each hall).The first wireless access point will need to be connected with a RJ-45 cable running from Home Hub. Can i connect the Wireless access points up together or do they all need to come from the ADSL hub?I am not sure what Wireless access points would be best and how to go about connecting this all up
View 2 Replies View RelatedI have New Pace 4111n Wireless Router that I got from AT&T and is setup on 1st floor, but its wireless range does not get me to 2nd floor. I also have the 2Wire wireless router from AT&T. In Addition, I have ethernet connection from level 1 to level 2 as well.
I was wondering if it is possible to have the Pace Wireless N router to work as modem and wireless access point, at the time use the 2Wire router to broadcast wireless and act as access point for 2nd floor.
IF its doable, how should the two be configured and connected.
I am trying to deploy several AIR-CAP3502E-E-K9 access points from a cisco 5508 wire lan contoller running ver 7 code. However iam having difficulty registering the access points with the WLC. The wlc is connect to a 3650 switch, and each access point is connected to a 2960 switch. A bad update was not allowing the access points to get their correct firmware.
View 7 Replies View RelatedI am having an issue here. I have 2x 5508 that each have 100 AP license and a little under 200 access points. Basically all of the access points are using DNS to connect to the primary controller that has the DNS entry. Basically half of my access points need to be on the second controller and in order to do this I have been using the high availability mode of each access point to push them to the second controller IP address.It was working perfectly until now. I have pushed 28 access points to the second controller and the last two I need to push at this location just keep resetting on the primary controller. Neither controller is configured as master controller.
View 4 Replies View RelatedI need an Wireless Access Point.Two SSID simultaneously in different IP Rangeit is with a simple browser GUI to manage? (not console and controller)a distance of about 50 (we can place multiple APs)N speedDual BandWhich series meets the above requirements?It can also Wireless-N Gigabit Router as 4400N, but it does not support Dual Band.
View 1 Replies View RelatedI have access points deployed across several buildings that each have a different IP scheme and their own T1 line. Is it possible to configure the 5508 controller to allow these access points to use the IP scheme assigned for that particular building or will dhcp always assign an IP address to the connecting client based on the IP scheme of the building that the controller resides in?
View 1 Replies View Related