I ran into a strange problem. When I want to change the ethernet0 interface of a Cisco 828 sdsl router, but there is no command to do that in the interface configuration mode (speed 100 and duplex full). A show interface gives 10MB half duplex and I want to change this.
This is the running config (a little censored):
!
!
interface Ethernet0
[Code].....
we have connected gig interface Ethernet on Cisco 2900 series router to mpls link connected to our corporate network ,the issue here is our router interface speed and duplex settings are set to auto negotiation.The interface is negotiating speed and duplex at 10 and half where the provider side interface is hard coded to 100 and full duplex.when we tried to hard code the settings on our router to match the provider the interface never come up.
View 4 Replies View Relatedwe have over 100 AP1242 with c1240-k9w8-mx.124-23c.JA2 image, tow 5508 controller and WCS running. After the ap reboots, the duplex settings of the fa0 interface change to half duplex. I have to set it manually to full duplex. In my WCS or with the 5508 controller I have no chance to set the duplex settings for my ap's.
View 7 Replies View RelatedIf I change the network adapter settings to 100 Full Duplex, is there any changes that will take effect? even if we don't have Cisco switches in our network.
View 4 Replies View Related3750G-12S-S.Problem description:I had a WS-3750G-12S-S in production with a defective fan tray and needed to change it.I faced to trouble with inter g1/0/1 on the new switch( it worked fine on the old).
Here the config for old switch:
interfacigabitEthernet1/0/1
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 111-113,278,790
switchpmode trunk
speed 100
[code]....
even if I configure speed nonegotiate that does not work.
I have a video conferencing device and I struggled a lot with a bunch of different routers. I was giving up but then I plugged in a friend's old Linksys/Cisco Adsl gateway and all the problems disappeared (kudos to Cisco). The problem is that the gateway is not ADSL2+. I have since borrowed a Linksys/Cisco ADSL2+ router, however, there isn't a possibility to enter port speeds/duplex manually (required to prevent packet loss in video conferencing, I really want to have that option for the peace of mind). I have been looking around on the internet but I can't seem to find this ability any routers' specs. What I need is as follows:
- Has to be Cisco or Linksys router
- Has to be ADSL2+ (Annex A)
- Doesn't have to be wireless, even single port is OK
- Preferably has DMZ
- Ability to hard code lan port speed/duplex (i.e. no autosense)
- No other functions needed so hopefully a cheap option
I have autonegotiation disable on my interfcae what should be duplex setting on other end?
Router#sh run int Gi0/3/0
Building configuration...
Current configuration : 334 bytes(code)
I am trying to hard code the speed and duplex settings on interfaces gigabit 0/1 - 2 interfaces with out success.
DSW121(config)#interface range g0/1 - 02
DSW121(config-if-range)#speed ?
Nonegotiate Do not negotiate speed
[Code]...
I have a broadband connection and recently I bought a new D-Link wireless router for accessing internet on my Android phone via Wi-Fi. Router model no. is N 150 DIR-524.After configuring it was working fine for a week or so and then one fine day internet stopped working on my PC and router LED for internet was not glowing as well. So I called my ISP and they changed my ethernet card settings (nVidia).They changed the 'Speed/duplex settings' from 'Auto Negotiation' to '10 Mb Half Duplex' and then the internet started working. During this they had disconnected my router. Once they were gone, I reset the router and connected it back. Since then it ain't working Internet works fine when the cable is plugged directly in the ethernet card but doesn't work when plugged via router. Router does everything right from opening the '192.168.0.1' page to saving the settings. But there's no internet access.
View 8 Replies View RelatedIs there a way to configure the GIG 0 interface on the 1552E Access Points to 10 Meg Full Duplex? Currently they will only work in Auto/Auto
View 3 Replies View RelatedI am using Linksys wirelless G router, will my wired speed on desktop increase when I change to a wirelless N router for laptop and ethernet for wired desk top? I don't need anymore wireless speed but am wondering if I upgrade will my wired desktop pick up more speed.
View 2 Replies View RelatedI connect a copper SFP on port 2 of WLC 5508 to a ASA 5510 firewall. The links between two devices are down. Since ASA 5510 only support 100 full, how do I change port speed on port 2 to 100.
View 8 Replies View RelatedSo I'm on the 100mbps virgin fibre optic broadband, and for the past couple of days, every now and again my speed drops drastically. It's not the Internet, because I've tested it on my laptop both wireless and plugged in. Even my phone and iPad are getting higher speed.
When I first got the internet(About a week ago) my download speed was 100+ mbps, but now my Link speed is constantly at 10mbps, even if I set my NIC to 1gbps full duplex, I've tried disabling and re enabling, I've tried uninstalling and reinstalling drivers, updating drivers. Restarting the router, starting it in Modem mode.
How to change internet speed 10mbs 100mbs?
View 1 Replies View RelatedI have configured the NCS 1.1.1.24 and its running fine, but i used the IP address 10.18.20.7(it was the WCS server), but now I want to use 10.18. 20. 8 (NCS Server) ip address.
so what should i do to change the ip address: I know only 1 thing that is, change the ip of the interface gig 0 .My main task is to run WCS and NCS parallal.
We use a wlc model AIR-CT5508-K9 with eight built-in ports. I would like to know if it is possible to change the speed of these ports down to 100Mb. At this time, they are set to auto and 1000Mbps.
View 3 Replies View RelatedI've been having this problem with my Belkin router since day 1 when i got it.( not new, got from buddy's place) It's Belkin HI Speed Wifi G router, and what's really frustrating is, everytime i connect to it, I need to manually change the DNS address and switch between 4.2.2.2 & 4.2.2.4 in order to get internet access! Sometimes it even cuts off the internet during a session, without me even disconnecting from the wifi network, where I would again need to switch back and forth to the 2 or 4 ending!
View 3 Replies View RelatedI currently have an out of the box ASA5505 and need to change the internal interfact from 192.168.1.1 to 10.20.3.1 so it fits in with the rest of the network.Tried using the ASDM Startup wizard (via 192.168.1.1) and it just seems to hang on "delivering the commands to the device".
View 16 Replies View RelatedWe have two ASA5510's, running IOS ver. 8.2(4). We setup Load Balancing on two ASA's. Will there be any problems if we change the IP address of the outside interface on one of the ASA's?
View 0 Replies View RelatedAfter my dir-655 recently bought the farm, I picked up a NIB 601 at a local computer mall for about $20. The drawback is that "local" for me means that the router is in Chinese.
Is there any way for the web interface language to be changed to English?
My X2000 modem connect only with small speeds Kbps, it's very weak than Linksys WAG54GP2 MBPS. If I put laptop near the modem speed doesn't change.Only change occurs when I change the channel. But it speed down after a while.I set, N connection, security is WPA-personal, tried some different channel, connection 20-40mhz, update the firmware (there is no problem with laptop, with another modem I can connect with 150kb/s speed) And, if I choose auto setup, security change to WPA, If I'm not wrong.
View 3 Replies View RelatedAccording to Cisco's site the WS-X6748-GE-TX is a "10/100/1000" module.URL
View 7 Replies View RelatedI have bought D-Link DIR-600 router from China and I want to change the web interface language to English.
-Router Info.
-firmware version: v1.03CN
-hardware version : A3
I have a Cisco 5510 which has remote access VPN configured.Now I have new block of IP address, is there a way I can just change the outside interface IP so that people can remote in without doing anythng else?Or if I coulds be taught to create a new one.Or best way to approcah this issue?For example: it was 67.64.x.x now I need to change to 64.44.x.x.
View 1 Replies View Relatedwe have two Cisco ASA 5510 in failover configuration.We tried to change the public IP address on the Outside interface of the primary device but it didn't works. The new IP is not reachable from Internet nor pingable from device on the same LAN.The new IP address is in the same subnet of the old IP.
From the switch on which the ASA is connected and from another Cisco PIX we can see the ARP entry. In the analysis, on the old public IP address there was a VPN site-to-site and Webvpn defined.We tried also to shut/no shut the interface and reboot the device.
We've recently shut down an interface on one of our ASA 5510s as we no longer use that service provider. The dashboard, however, still insists on showing traffic usage on this interface. How do I change the dashboard to display a more meaningful interface?
View 7 Replies View RelatedWe've been trying to monitor the used bandwidth of our SGE2000 and SGE2010 switches with Nagios.We've been experimenting with the various OIDs and we've found the OIDs linked to the different switchports.
Though when we use SNMPWalk (to find the OIDs connected to the port) the names of the ports are all the same.
[code]....
Is there a way to change the names of these interface to unique names?We've already given unique names in the description field through the switch's GUI, but it doesn't make any difference for Nagios.
i have firwall ASA5400, and the outside interface connected to internet router but i noticed that the interface speed in the outside interface is 1000M, but on the internet router is 115 M. so the interface in the router is highly utilized and also the firwall cpu highly utilized. [code]
View 0 Replies View RelatedRegion : China
Model : TL-WR941ND
Hardware Version : Not Clear
Firmware Version :
ISP :
I bought a TP Link router to access internet. Nevertheless the routur interface is in Chinese language which is not convenient for me to set it up.How to change the interface language ? How to upgrade the routur interface to an english one ? (in the website I cannot see firmware for V6).
I am switching a switch connecting to the ASA5550 tomorrow. My current switch is using fiber connecting to the ASA. The new one only support copper. If I switch between fiber to copper on the ASA (change media-type command on interface) will it cause a down time? I have VPN tunnel on the ASA and don't want the session to reset.
View 2 Replies View RelatedI am facing port speed issue on WS-C2960G-48TC-L series switch.This switch gig0/X ports connected to onother switches (Cisco and HP both switches are also gigbit ports and directly connected ).but interface is giving only 100mb/s output.ios on WS-C2960G-48TC-L is 12.2(44)SE6
View 15 Replies View Relatedi'd like to force the speed/duplex of the integrated Gigabit interface on a LAP1042N, managed by a 4402 running software version 7.0.98 but I cannot find the command either by command line or on the GUI.
View 3 Replies View RelatedHow can I change the language of the admin interface on a belkin wireless router (F7D2401) it all appears dutch.
View 2 Replies View Related