Cisco :: Speed On Gigabit Interface
Mar 14, 2012According to Cisco's site the WS-X6748-GE-TX is a "10/100/1000" module.URL
View 7 RepliesAccording to Cisco's site the WS-X6748-GE-TX is a "10/100/1000" module.URL
View 7 Repliesi'd like to force the speed/duplex of the integrated Gigabit interface on a LAP1042N, managed by a 4402 running software version 7.0.98 but I cannot find the command either by command line or on the GUI.
View 3 Replies View RelatedI have a question about speed negotiation process between interfaces. I have 3650X Sw and 2960S-48port. All ports of two are GigabitEthernet, however the link between them is only 100Mb/s, Full duplex. I try to set the speed 1000 Mb/s manually in the interface then the interface never up. Its status is down/down. I must set back to speed auto. I show interface Gigabit0/24 in Sw 3650-X and figure out that there are many output drop (over 600000). I clear counter then after two days the output drop is over 70000. This link is trunk link between two switches, all ports of access SW are Gigabit and connect to PC. First, I thinks the 3650X is throttled somewhere in output direction of trunk link. But there is another trunk link (Gi0/23) to another 2960S-48port and no output drop number in this interface. This Giga 0/23 speed is 1000 Mb/s (auto speed, auto duplex)
Does any outside things impact the speed negotiation process between 2 interfaces? And output drop number may caused by abnormal speed between two Gigabit interface?
I have an Ethernet Loopback Plug (4 Pairs) made and trying to test the Gigabit Interface on a 3845 Router with a fail result. The interface will show up/up only if I set the interface to 100M/Full Duplex when I plug-in the Ethernet Loopback Plug (4 Pairs). I don't see this Gigabit Interface @ 3845 router has any option to set it to internal or external loopback.
View 2 Replies View RelatedI've got a Buffalo LS-WXL5BF connected directly to one of my PC's gigabit ethernet ports. The link in the Win7 network and connections is showing it connected at 1Gbit but the actual transfer speed tops out around 150-200 Mbit or roughly 15-25MB/s (which is well under what the unit is advertised to perform at.)
I'll be swapping out the cable that came with it for a good CAT5E I got from monoprice but other than that I'm not sure what to try.
to what extent gigabit lan port affect speed of internet?
View 1 Replies View RelatedI have a desktop and a laptop computer. both equipped with Gigabit Lan port... I connect them with Straight cable by assigning both computers IP address. I havnt use any switch or router between computers.... The problem is that my transfer speed is about= ~10MB/s..... As far i know the transfer speed should be around 70-80MB/s (125MB/s for Gigabit Lan).....
View 5 Replies View RelatedMy laptop will not connect at full speed whilst on a wired connection. All my other laptops connect at full gigabit speed OK using the same cable. My XPS will only connect at 100Mbps.I have the Realtek PCIe GBE Family Controller.
I am using Win 7 64Bit but I have also tried Ubuntu 12 with the same result. Is this a known problem ?I think this may have been like this since new, My most expensive laptop is the slowest on my network.
I am using a Cisco ME 3800 switch with 24 Gig and 2 Tengigabit interface. But after configuring the Tengig int with ip add and negotiation it is no know visible in the switch. Instead TenGig I am seeing two (Gi0/1 and G0/2). Not even showing the Tengig in the running config.
View 3 Replies View RelatedI am currently connected to my router via a 100 megabit cable (the router port itself is either 100M or 1G, I can't remember). There are no free ports on the router, but I want to connect additional computers to the network. If I get a gigabit switch and connect two of my PCs to it using gigabit cable, can they communicate at gigabit speeds, or will they be limited by the 100M connection back to the router? (In other words, does traffic between two computers on the switch have to be sent through the router, or not?)
View 2 Replies View RelatedI have a two computer network. Here are the network adapter details of the two computers.
-Realtek RTL8111E Gigabit Ethernet Controller
-Broadcom NetXtreme Gigabit Ethernet
I'm using a CAT5e cable. But it gives only a 10 MB/s file sharing speed. What is the reason for this? (In both the computers under "Local Area Connection Status" it shows 100 Mbps for the speed)
my problem is that i have a computer connected via gigabit lan with a cat5e cable.i have a notebook with a d-link dwa-140 usb wifi adapter connected.and the max transfer speed i get is 14 mbps. d-link dir-655 firmware 1.34eu.in windows it reports 300mbps.in the router it reports 270 mbps sometimes 300. the settings in the router is 40mhz only,. ch 13. wpa2 aes. as described in the sticky.the devices are within 3 ft of each other.
View 2 Replies View RelatedI cant figure it out and can not find a solution. All three computers have gigabit nics, I have gigabit router and switch, my d-link 321 is set to gigabit, the only thing on my network that is not gigabit is my printer. I'm not getting gigabit transfer speed from my computer to dlink 321. I rarely do computer to computer transfers, so I dont know what the speed is of that. The best tranfer rate is from 7-12mb. I am also using cat 5e wires on all connections. What am I missing?
View 12 Replies View RelatedI've got Cisco 7609 with WS-X6708-10GE (8x10Ge)And one port (te9/4) from it have zero bit rate counters, but all the rest of it are very good.I can see traffic if read it by SNMP. [code]
View 1 Replies View RelatedWe have a number of 3845 routers, some running IOS 12.4(22)T2 and earlier and some running 12.4(24)T4. On the ones with 12.4(22)T2 and earlier, gigabit interface g0/1 shows interface down/line protocol down when there is no cable connected to the interface and the interface is not in shutdown state. On the ones with 12.4(24)T4, gigabit interface g0/1 shows interface up/line protocol down when there is no cable connected to the interface and the interface is not in shutdown state. Interestingly in both cases, the "show controller g0/1" command shows " network link is down (NO CARRIER)" when there is no cable attached. It makes sense to us that the interface status would be down/down when there is no cable attached. It does not makes sense to us that the interace would be up/down. Did Cisco at some point change their philosophy on whether an interface should show down/down or up/down when there is no cable attached, or is this a bug?
View 1 Replies View RelatedHave been running win 2000 pro for last 5 yrs with trendnet pcitxr 1 gigabit nic card. Never had any problem running & connecting. Now cannot access internet @ 1 gigabit, ok @100mbit, for the most part. sometimes browser will lock-up, firefox or IE. Never had any problems like this before. Have changed nic card, replaced cable modem, wires. Have delete trendnet software and reloaded, ran winsock fix, move router cables, ran directly from cable modem, bypassing router, move nic to new slot, ran ipconfig /release & reset. All to no avail. when I ping comes back good. NIC cards I have tried all seem to be working.
View 1 Replies View RelatedI have purchased Linksys WRT320N because my ISP give me speeds of 400 mb/s download and 200 mb/s upload. After I tested the speed my router get only 137 mb/s, why is that? I paid for gigabit router!?
View 7 Replies View RelatedI have configured Priority Queueing in my Cisco 2911 Router. I have set queue list high, medium, normal and Low. But when I put show interface gi0/2, it is showing the queueing strategy is priority queueing but it is not showing the (size/max/drops) values.
View 1 Replies View RelatedI want to connect 2 ISP links into one Gigabit-interface on my Router 2921, can any one tell me how to do that ? sub-interface creation is not possible on cisco 2921
View 1 Replies View RelatedIf I connect wire directely to the PC Ethernet port the Internet speed is about 400 Mbit/sec (speedtest.net)When my PC is connected through the Linksys E4200 Internet speed is not above 90 Mbit/sec.
View 1 Replies View RelatedI am trying to configure a loop back interface like so: [URL], on the following device:
C3550 Software (C3550-IPSERVICESK9-M), Version 12.2(50)SE, RELEASE SOFTWARE (fc1on port gig0/1 which is using a 1000Base-SX adapter. This is for troubleshooting purposes and it does not appear to be a feasible option. Is there another way to accomplish in the IOS?
I'm running an Optiplex 330 with the Broadcom NetXtreme 57xx Gigabit ethernet card.
The computer is running Windows 7, 64bit, but there do not appear to be any drivers for that OS.I tried selecting Vista 64bit, but there were no drivers. The Vista 32bit doesn't work.
Then I went to Broadcom and found these drivers: [URL] the W764bit drivers didn't change the fact i'm still on a 100Mbit card (as seen on Local Area Connection Status screen and the Device manager)
I ran into a strange problem. When I want to change the ethernet0 interface of a Cisco 828 sdsl router, but there is no command to do that in the interface configuration mode (speed 100 and duplex full). A show interface gives 10MB half duplex and I want to change this.
This is the running config (a little censored):
!
!
interface Ethernet0
[Code].....
i have firwall ASA5400, and the outside interface connected to internet router but i noticed that the interface speed in the outside interface is 1000M, but on the internet router is 115 M. so the interface in the router is highly utilized and also the firwall cpu highly utilized. [code]
View 0 Replies View Relatedwe have connected gig interface Ethernet on Cisco 2900 series router to mpls link connected to our corporate network ,the issue here is our router interface speed and duplex settings are set to auto negotiation.The interface is negotiating speed and duplex at 10 and half where the provider side interface is hard coded to 100 and full duplex.when we tried to hard code the settings on our router to match the provider the interface never come up.
View 4 Replies View RelatedI am facing port speed issue on WS-C2960G-48TC-L series switch.This switch gig0/X ports connected to onother switches (Cisco and HP both switches are also gigbit ports and directly connected ).but interface is giving only 100mb/s output.ios on WS-C2960G-48TC-L is 12.2(44)SE6
View 15 Replies View Relatedmy office is looking in ordering a HWIC-1FE to supply our cisco 1841 router with a second ISP connection. i wanted to find out if this card support load balancing and fail over? not sure if fail over is the right terminology so ill explain, i need it so that if one ISP connection goes down (as it does often) it fails over to the second ISP.
View 3 Replies View RelatedIs there a way to know from the web interface the wifi speed of the connected clients?
View 1 Replies View RelatedI have a ASA5510 and I have a question about the speed the ports can handle, here is one port:
-interface Ethernet0/2
- speed 100
-shutdown
- no nameif
-no security-level
-no ip address
it's ethernet and not fastethernet so I figure it will only go to 10Mbps, but at the same time I can hard code the speed to 100.
What s the fabric speed (backplane speed) of a Nexus 2232 10G EX?What is the forwarding rate (Mpps) of the same 2232 FEX?
View 6 Replies View RelatedI just discovered that my wireless download speeds are 5Mbps, compared to 16Mbps if my laptop is connected directly to the modem or wired through the router. Uploads are 2Mbps either way. I have a WRT54GS v.6 with firmware version v1.52.8 which I updated today, completed by setting factory default through the router webpage after I discovered this discrepancy. The firmware update did not improve the download speed appreciably, if at all.Should the wireless connection be that much slower than the wired connection through the router? If not, what sort of issues could I be having to account for this?
I did just replace my modem when I discovered I was having erratic speedtests and that corrected that problem. That is when I became aware of the wireless issue, so not sure how long that has been the case. I have Charter's 16/2 HSI, living in a sparsely populated area with solid internet service. There is no external nor internal interference on this 2.4Ghz band.
I have a Arris DLS with 12 Mbps Download and when I Connect my laptop directly I get the same speed as 12 Mbps but when I do the speed test with my linksys I get only 5 Mbps. How to upgrade to the new WRT54GL or WRT54GS?
View 1 Replies View RelatedRecently my desktop has experienced very slow download speeds (~0.11 Mbps), however the upload speed appears to be in line (~2.0Mbps). These numbers are taken from Comcast's speed test (my ISP). It is obviously a problem with my PC because everything else on the network (PS3, Laptop) have great signals with no problems. I just recently reverted the Desktop back to its factory state, and everything was working fine for a couple of months. The desktop in question uses Vista 32-bit and the Belkin Basic USB Wireless Adapter.
View 1 Replies View Related