I connect a copper SFP on port 2 of WLC 5508 to a ASA 5510 firewall. The links between two devices are down. Since ASA 5510 only support 100 full, how do I change port speed on port 2 to 100.
View 8 Replies
We use a wlc model AIR-CT5508-K9 with eight built-in ports. I would like to know if it is possible to change the speed of these ports down to 100Mb. At this time, they are set to auto and 1000Mbps.
View 3 Replies View RelatedI am using Linksys wirelless G router, will my wired speed on desktop increase when I change to a wirelless N router for laptop and ethernet for wired desk top? I don't need anymore wireless speed but am wondering if I upgrade will my wired desktop pick up more speed.
View 2 Replies View RelatedI have more different client networks with one ssid, when a client is in another network gets an ip it still from the old network.
How can I to the wlc change this so he gets one right address. I have a Cisco WLC 5508 and 1262/1252 Access point
I have an issue where I cannot get clients to change SSID. I have two SSID, one WPA2 secure, one open guest. The secure is locally switched via Flexconnect and the guest is centrally switched. Both of them work. I have been able to test this and both work as intended. The problem is that once you connect to one of them, either secure or guest, you cannot then change to the other. The only way to change is to delete the dhcp entry from the scope and then do it.
Fast SSID change is enabled. I also have debug client output from when the client fails when you try to switch which I will include below. I also pulled some wireshark captures and those show me that the DHCP ack packets are trying to give the client the ip address from the incorrect/previous scope. So basically it's like FAST SSID change is not working and the client is never being disassociated properly??
I am totally stumped and even though the client will most likely not be switched between SSID that often I would still like to know the solution.
Cisco 5508 running 7.2.110.0
Cisco 3502 LWAPP
windows server 2008 dhcp server
[Code].....
How can i change AP host name for LAP via CLI? I got the error 'command is disabled' when i try to use command 'capwap ap hostname <>'
I try to disconnect LAP from WLC, factory default, clear all private-configure and clear all files in nvram: but not working (still got error). I cannot change via WLC GUI for CAP2602I series. I don't know why.
I checked bug CSCsy17745 but current in use software is fixed.
WLC 5508 with 7.3.101.0
I have two 5508 and one WCS server, the controllers are in one mobility group.Now I have to change the management IP addresses on the controllers. What are the correct steps to do this?
View 9 Replies View Relatedi see there is an option to "allow password change" or "force password change" for guest roles in the NGS. But when i created a guest account using this guest role, after webauthentication , there is no prompt to change password. Is this the intended behaviour or is there anything else that i need to configure. Looking at it, i am not sure how the NGS would allow a "guest user" to really overwrite the password by allowing password change. ? is that not a security risk as well for the NGS ? my setup has 5508 anchor controller and NGS communicating via RADIUS.
View 7 Replies View RelatedI just get to hands-on on my new WLC 5508?
1) I'm using a single subnet eg 192.168.1.0/24 for my wireless clients and i'm assigning them via the DHCP server from the WLC. As the clients are however made up of laptops and scanners, i would like to assign a range from 50-150 for the laptops and 151-250 for the scanners for easier identification. But it seems that from the WLC DHCP menu i'm not able to do this unless i segment them into a different network with different gateways.
2) Is there anyway to change the WLC user accounts password too? I dont seems to be able to find the option unless i delete the account and re-create it with the new password.
So here is my network.
ASA5505--->Cisco1841--->Cat2960
Code
ASA asa831-k8.bin
Cisco 1841 c1841-adventerprisek9-mz.151-4.M2.bin
Cat 2960 c2960-lanbasek9-mz.122-55.SE1.bin
and here is my dilemma.
I can SSH from the internet to my ASA on default port 22, directly to my public IP. I can SSH from the internet to my Cisco 1841 on port 2001. I can not however, SSH to my Cat 2960. From what i can tell, on the Cat2960 i can't change the default port 22 for SSH to different port, just like i did on the Cisco 1841. I looked to see if I can change the default port for SSH on he ASA, it does not look like this is an option.
The bottom line is that i want to be able to SSH to all three devices from the internet. I only have one public IP. As of now, what i can do is only SSH to the ASA on default port 22 directly to the public IP and Cisco 1841 on port 2001. It appears that changing the default SSH port on Cat 2960 is not an option. It also appears that I can't change the default SSH port on the ASA, if i could, i would and then i should be able to SSH to the Cat 2960 on port 22. No matter what i did on the ASA, it always listens on port 22 for SSH connections.
show asp table socket
TCP 001f549f <<pub IP>>:22 0.0.0.0:* LISTEN
how do i make it listen on different port?
Here is relevent config for SSH for cisco 1841 (port forwarding)
ON ASA
object network ROUTER
host 10.10.1.1
[Code].....
I have Cisco 800 series (888w) with BRI-ISDN port. Is there any way to change the usage of ISDN port to normal RJ45 port?I want to use this SOHO router to sharing connection.
View 0 Replies View RelatedWhat is the purpose of Redundant Port that says "future use RJ45" on the Cisco WLC 5508?
View 3 Replies View RelatedI ran into a strange problem. When I want to change the ethernet0 interface of a Cisco 828 sdsl router, but there is no command to do that in the interface configuration mode (speed 100 and duplex full). A show interface gives 10MB half duplex and I want to change this.
This is the running config (a little censored):
!
!
interface Ethernet0
[Code].....
I have a 5508 WLC and a series of 1140 APs. One small but annoying thing I have noticed is that the APs are pulling the correct time from the WLC but the timezone is off so they are showing time at 0 and not -8. The timezone is set and correct on the WLC.
View 9 Replies View RelatedI'm having an issue with the 5508 management port .. I can't seem to ping it from the switch connected to it .. ( the Show cdp command shows that the two can see each other .. but no ping is possible ! [code]
View 4 Replies View RelatedI want to configure Port channel for WLC 5508 and cisco 3750 Stack Switch. What changes I need to make on WLC and where?
View 7 Replies View RelatedWe are trying to set up Out of band connection for Cisco 5508 WLC and when we try to ssh to the Service port from a remote switch, this fails. SSH or Telnet to the Management IP address works fine. The Service port and Managment IP are in the same IP scope but different subnet..i.e 172.16.10 for Management and 172.16.99 for Service port. Also, as this set up will be HA (AP SSO) in future, for which DHCP is recommended for the service ports, just wondering if SSh will be possible.
View 7 Replies View RelatedSo I'm on the 100mbps virgin fibre optic broadband, and for the past couple of days, every now and again my speed drops drastically. It's not the Internet, because I've tested it on my laptop both wireless and plugged in. Even my phone and iPad are getting higher speed.
When I first got the internet(About a week ago) my download speed was 100+ mbps, but now my Link speed is constantly at 10mbps, even if I set my NIC to 1gbps full duplex, I've tried disabling and re enabling, I've tried uninstalling and reinstalling drivers, updating drivers. Restarting the router, starting it in Modem mode.
How to change internet speed 10mbs 100mbs?
View 1 Replies View RelatedI have 2 x 5508 Wireless Controllers, 1 mgmt port on each as standard. I noticied something different between these controllers running the same code.I can bound a physical port to the mgmt interface on one controller but not the other (both interfaces are untagged)see below, this config appears on one controller but not the other? Is this something to do with the initial setup? How can I add Phyiscal information to the other controller mgmt interface, I cannot delete the mgmt interface. Physical InformationPort Number Backup Port Active Port Enable Dynamic AP Management?
View 2 Replies View RelatedI'm having some difficulties configuring my Cisco WLC (5508) - ver 7.0.230.0 .I'm have multiple client device residing on same vlan associated to the WLC but unable to telnet over port 8090. However, when inter-vlan, client device able to telnet over port 8090.Say Machine A as application hosted machine and Machine B as client machine; [code] i should be looking on the WLC to allow telnet port 8090 over from Machine A to B within the vlan .
View 2 Replies View RelatedSince WLC5508 MGMT interface is configured a AP-Mgr at the same time, can I set a Backup Port to WLC5508 MGMT interface? Refer to WLC configuration Guide:
In the Backup Port text box, enter the number of the backup port assigned to the management interface. If the primary port for the management interface fails, the interface automatically moves to the backup port.
Note Do not define a backup port for an AP-manager interface. Port redundancy is not supported for AP-manager interfaces. If the AP-manager interface fails, all of the access points connected to the controller through that interface are evenly distributed among the other configured AP-manager interfaces
if I need to configure the backup port for MGMT interface, i need to remove the AP-manager on MGMT interface and create a network dynamic interface for AP-Manager ?
I have setup LAG for one of our 5508 controllers and have connected 4 of the 8 ethernet ports to a 4507 switch. After configuring 2 port channels on the switch we are receiving a host flapping error between the port channels and it seems to be causing a serious slowdown on the switch. When I shutdown one of the port channels the error goes away and traffic returns to normal. I have the same configuration at other locations with the only difference being the switches used are 3750G-12S and I do not see the host flapping error. It appears to only be a problem with modular switches.
One other thing of note: I read a Cisco white paper on LAG and it suggested creating the port channels over 2 different modules. For example, put ports G4/24 and G5/24 in port channel 1 and G4/25 and G5/25 in port channel 2. I tried this but I still got the host flapping error.
Let's say I have 3 APs, all connected to a WLC 5508,Each AP has a computer that is connected to it, Computer A, B and C, all on the same Vlan with same SSID
Is it possible to configure so
A and B can not talk to each other but both can talk to C ?
Something like "protected port" feature in the switch world.
I have found some samples on the FlexConnect setup for the controller side. However none of the documents mentioned how the switch port should be configured that goes to the controller and AP.
At this moment I have a Cisco 5508 configured in CAPWAP mode with 20 APs. I would like to use same controller for connecting one of the remote sites with 2 APs in FlexConnect mode. Current the 5508 to switch port is configured as 802.1Q port. All CAPWAP AP ports are configured as "switchport access vlan X" where X=capwap VLAN. Need to know how the switch port should be set for the remote site where flexconnect APs connect.
So currently I'm having issues with changing my nat type to open for my ps3. I've tried to use DMZ and port forwarding to change the nat type, but sadly I couldn't get this to work. Most the guides on the forums are for xbox's which wouldn't work for a ps3. Any handy guide to change my nat type to open for my ps3?
View 5 Replies View RelatedI've been having this problem with my Belkin router since day 1 when i got it.( not new, got from buddy's place) It's Belkin HI Speed Wifi G router, and what's really frustrating is, everytime i connect to it, I need to manually change the DNS address and switch between 4.2.2.2 & 4.2.2.4 in order to get internet access! Sometimes it even cuts off the internet during a session, without me even disconnecting from the wifi network, where I would again need to switch back and forth to the 2 or 4 ending!
View 3 Replies View RelatedI have been monitoring the alarm summary but have been off couple days and i see one of my controllers is down. Getting critical level security and message is port is down on the controller, condition link down. The other issue is config difference found between NCS and Contoller, I tried getting them to sync together but still getting the same message.
View 1 Replies View RelatedIs there a way to change the timeout for the Client Excluded: MACAddress status? It seems like the exclusion is rather short. I'd like to have the ability to control the exclusion time. Using WLC-5508 7.0.116.0.
View 2 Replies View RelatedMy X2000 modem connect only with small speeds Kbps, it's very weak than Linksys WAG54GP2 MBPS. If I put laptop near the modem speed doesn't change.Only change occurs when I change the channel. But it speed down after a while.I set, N connection, security is WPA-personal, tried some different channel, connection 20-40mhz, update the firmware (there is no problem with laptop, with another modem I can connect with 150kb/s speed) And, if I choose auto setup, security change to WPA, If I'm not wrong.
View 3 Replies View RelatedIn 'Status' on my router there is a green dot in the field below 10/100 mbps at 'Internet port speed' - shouldn' that dot be below 1 gbps?
View 1 Replies View RelatedAfter reboot WLC , the switch port was err-disable , the cause is link flap after we reboot 3 times , the switch port link flap err-disable every time? We don't know why the WLC rebboot will cause it , it just normal action on device the WLC version is 7.4.100.0 link switch with access port , no port channel , no portfast.
View 11 Replies View RelatedI have TL-WR740N router. ISP should provide me up to 100Mb/s internet speed. Actual measurements shows me about 80 Mb/s. The problem is when I enable 3389 port in Port Triggering my internet speed drops to 2,5 Mb/s. When I disable port triggering, speed become normal again.
View 3 Replies View Related
