Link Speed Set To 10mbps - Doesn't Change
Mar 9, 2013
So I'm on the 100mbps virgin fibre optic broadband, and for the past couple of days, every now and again my speed drops drastically. It's not the Internet, because I've tested it on my laptop both wireless and plugged in. Even my phone and iPad are getting higher speed.
When I first got the internet(About a week ago) my download speed was 100+ mbps, but now my Link speed is constantly at 10mbps, even if I set my NIC to 1gbps full duplex, I've tried disabling and re enabling, I've tried uninstalling and reinstalling drivers, updating drivers. Restarting the router, starting it in Modem mode.
View 1 Replies
ADVERTISEMENT
Jul 23, 2011
I have used DIR-655 (HW:B1 FIRM: 2.00NA) with Motorola SB6120 for sometime without any incidents. My dl speed usually is around 26mbps. Lately, it happens twice that the dl speed drop to 10mbps. If I connect the SB6120 directly to my PC, the dl speed is 30mbps. Is my DIR-655 dead?
View 8 Replies
View Related
Oct 23, 2012
My X2000 modem connect only with small speeds Kbps, it's very weak than Linksys WAG54GP2 MBPS. If I put laptop near the modem speed doesn't change.Only change occurs when I change the channel. But it speed down after a while.I set, N connection, security is WPA-personal, tried some different channel, connection 20-40mhz, update the firmware (there is no problem with laptop, with another modem I can connect with 150kb/s speed) And, if I choose auto setup, security change to WPA, If I'm not wrong.
View 3 Replies
View Related
Mar 20, 2011
The Setup On my home network, I am running Windows Server 2003 as domain controller and file server with a SCSi attached disk array.I have several client PC's. 2 running Windows XP service pack 3, 1 laptop running Windows 7 Service pack 1 and a desktop also running Windows 7 Service Pack 1.These are connected by 2 switches - 1 x Netgear gigabit switch, and a Linksys PSUS4 USB Print server at 100mbps.The PC I use the most is the desktop running Win7 and transfer files to the server.After transferring some large files from the clients to the server, I noticed that the speed was considerably slower than what I was expecting it to be. After investigating, and eliminating elements of the network, I discovered that the Server NIC was running at 10mbps. I tried the usual things like forcing the NIC to run at 100mbps Full Duplex but this had no effect. Strangely, if I reboot the server while the desktop is still switched on the connection goes back to 100mbps. However if I reboot the desktop, or even alter the network settings, it immediatley reverts back to 10mbps.
View 17 Replies
View Related
Aug 15, 2011
My LAN speed was 100 Mbps but now it is 10 Mbps and too slow when I am using internet. So how can i increase the speed to 100 Mbps from 10Mbps?
View 2 Replies
View Related
Feb 17, 2013
Tech Support Guy System Info Utility version 1.0.0.2
OS Version: Microsoft Windows 7 Ultimate, 64 bit
Processor: Intel(R) Core(TM) i5-3570K CPU @ 3.40GHz, Intel64 Family 6 Model 58 Stepping 9
Processor Count: 4
RAM: 4060 Mb
Graphics Card: ATI Radeon HD 5670, 1024 Mb
Hard Drives: C: Total - 426837 MB, Free - 258482 MB; D: Total - 49998 MB, Free - 49015 MB; G: Total - 476937 MB, Free - 175903 MB; J: Total - 12071 MB, Free - 7763 MB; T: Total - 102397 MB, Free - 64670 MB;
Motherboard: ECS, Z77H2-A3
I have been paying Time Warner Cable for 50mbps download, but have been getting just under 10mbps for quite some time (ethernet,NOT wireless, we have no wireless-capable devices) After hours on the phone with Tier 3 tech support, two visits from technicians, a replaced modem and countless hours googling, I am at my wits end.When I go into the Task Manager and look at Networking, it shows the Link Speed at 10 Mbps.I have gone into my network adapter settings and set the Speed/Duplex to 100mbps Full, as the TWC rep said.Also switched cables, powercycled, rebooted the PC, etc.Google searches suggest going into the router settings and raising the cap through there, but I can't find the proper setting for my device (Motorola SURFboard SBG6580) if they even exist at all. it's using slightly outdated firmware ( SBG6580-3.3.1.0-GA-09-058-NOSH ) and that that could be causing the problem.
View 4 Replies
View Related
May 26, 2012
I've been having issues with my DIR-655 - the speeds are super slow. In the past, I've been able to restart the modem, and my speeds would be acceptable, but now a restart doesn't change the speeds I'm getting from speed test.net. I know it has to do with the router, because when I directly connect to the modem, my speeds are great.
-Speeds WITH router:
-Speeds WITHOUT router:
And like I said, in the past I could restart the router, to get similar speeds to just my modem, but it doesn't work that way anymore.
View 1 Replies
View Related
Nov 11, 2012
I've been trying to find a response or a fix to this issue for a few weeks now.My DIR-655 RevB router is currently at firmware 2.07NA, and has speeds of around 30Mbps down and 10Mbps up when connected directly through wired connections.However over wifi, I am only getting around about 5 Mbps down and 2 Mbps up. I've tried the 'usual' fixes suggested on here, change broadcast signal to manual, not auto, shutting of QoS shaping, all of that. However nothing seems to be improving the speed.
View 8 Replies
View Related
Mar 9, 2012
I am using Linksys wirelless G router, will my wired speed on desktop increase when I change to a wirelless N router for laptop and ethernet for wired desk top? I don't need anymore wireless speed but am wondering if I upgrade will my wired desktop pick up more speed.
View 2 Replies
View Related
Apr 8, 2011
How come my IP address does not change when i'm using my router.... (TP-link WR340G)But when i connect my DSL directly to my computer it my IP can be changed..... and when i put back my router my IP address is the same.
View 1 Replies
View Related
Mar 17, 2011
I live in the tampa bay area, I have bright house (BHN) as my service provider, which provides a Road Runner Lightning (40/5) package. I previously used BHN's top tier (20/2) back in July (and prior) with no problems.
After converting to Lightning in August of this year (2010). Of course, BHN (and every other provider) wants to force a modem/router down your throat, so I had them bridge it (in short, turn it into a dummy modem with no routing). I had an SMC branded modem gateway at the time. I work from home 2 days a week (so I can spend more time with my kids during morning, lunch, right after work) and this requires me to use QoS to ensure my VOIP work calls don't get dropped, if the family is watching youtube videos or watching netflex.
My network was as follows SMC Modem >WAN IP>>WAN Port>>D-link DIR-655>>Switch Ports>PC1, PC2, PC3
Everything seemed fine (from a usability stand point) till about 2 weeks ago when my upload speed seemed to grind to halt. Normally I was able to upload about 200-300K per second, and I noticed this dropped to about 45K per second during a drop box upload. First thing I did was power cycle both my modem and router (in the proper/usual order). After they both come up, I start using speed test to find out what my upload speeds were. I was getting about 39Mbps down, but only .56Mbps up still. I factory reset my router.... test, similar speeds. Power cycle all computers (just in case), and then modem/router. Tested, similar speeds. Updated the firmware to the latest. Same issue
Called BHN customer service, they factor reset it, but it wasn't in bridge mode. If I by passed the 655, in factory mode (non bridge mode) upload speeds returned to better than expected states. If I bridged the cable modem, upload speeds seemed to crash.
Had BHN replace the modem, seemed fixed for a day, then issue came back. Had them come back out and replace it again, this time with a Motorolla Surfboard modem... same issue. Fine during factory reset, however after they bridge the modem, upload speeds were fine. Told BHN I would take it from there.. Connected up the DIR-655, and upload speeds crashed again. (.6Mbps). Called D-Link Support, and the Chinese English speaking rep seemed to not be listening to me and tried to have me adjust my MTU as well as Wireless settings. Long story short... the rep was a level 0 id10t and I hope D-link will consider hiring better employees/contractors. So I was all about to give up and replace it with a DD-WRT capable router (which it takes me a lot to want to swap hardware), when I discovered the wan shaping was on. Which I thought to myself... nah... QoS has never messed up before... why would it be the cause. Turned off wan shapping... and voila. Issue seemed to be insta-resolved.
Unsatisfied with that... I decided to dig a lil deeper. I turned on Wan shaping again, but decided to set the settings manually instead of auto detect.
Here are the settings I used... (Advanced Tab>QoS)
Enable Traffic Shaping - Checked
Automatic Uplink Speed - Unchecked
Manual Uplink Speed - 5000
Connection Type: Cable or Other Broadand Network
Enable QoS Engine - Checked Automatic Classification - unchecked (this checked seemed to affect my upload speed by about 5-10% during testing) Dynamic Fragmentation - unchecked (this checked seemed to be the worse enemy for upload speed)
While I know I'm not any network guru (still have to use a subnet calculator for subnetting), I think I did a pretty good job drilling down the issue (once I got passed my service provider replacing modems).
Anyways, I've had overall good luck with D-Link products, even have a 5 port 10/100 switch (all metal) from 1998 that works great. Hopefully, D-Link will just either put more documentation on the web, or hire better employees.
View 3 Replies
View Related
Aug 8, 2011
I use CiscoWorks LMS 4.0.1.
I planned a discovery of devices for some time, but if I change the parameters of discovery (adding a seed device) in "Discovery Settings Summary", this change does not apply in the scheduled task.
If I change the settings in the scheduled task, the changes do not apply in "Discovery Settings Summary". We must change the settings 2 times.
View 1 Replies
View Related
Jul 19, 2012
How to change internet speed 10mbs 100mbs?
View 1 Replies
View Related
Oct 22, 2012
I ran into a strange problem. When I want to change the ethernet0 interface of a Cisco 828 sdsl router, but there is no command to do that in the interface configuration mode (speed 100 and duplex full). A show interface gives 10MB half duplex and I want to change this.
This is the running config (a little censored):
!
!
interface Ethernet0
[Code].....
View 2 Replies
View Related
Feb 25, 2012
don't know what to do. For a good while now, at my home, the internet has been awful.Web pages barely load if at all, I can't play any online games, but when I start a download, either by torrent or regular, the download speed is perfectly fine, reaching the normal 500 kb/s. My router is TP-Link W9801G. We get TV through the router as well, and there never was any problem with it. It works fine, just like the download speed. The DNS and IP settings are all set to automatic like they should, and of course I've tried unplugging and resetting everything.I know it's not the computer's network adapter, because it's the same thing at my laptop when I connect to it wirelessly. The signal strength is at all 5 bars too
View 2 Replies
View Related
Jul 29, 2012
It has been 4 months since I upgraded my internet connection from 2 mbps to 4 mbps.I have called the ISP but they say the speed is okay.When I open 192.168.1.1 it says(datas shown below),but everytime i download something or measure my internet connection it never goes more than 2 mbps (max 230 kbs download[CODE]
View 3 Replies
View Related
Jan 24, 2011
I have a Cisco router 877. I am trying to configure a backup with ISDN.The primary line is an ADSL over pppoe. The problem is that despite the primary line fails, doesn't change the path and continue going by the main route.I have a very similar setup, also with a cisco 877, but with a normal DSL and it works perfectly.I solved the problem by activating a tracking but is slower than the other method.
View 2 Replies
View Related
Oct 12, 2011
I've been having this problem with my Belkin router since day 1 when i got it.( not new, got from buddy's place) It's Belkin HI Speed Wifi G router, and what's really frustrating is, everytime i connect to it, I need to manually change the DNS address and switch between 4.2.2.2 & 4.2.2.4 in order to get internet access! Sometimes it even cuts off the internet during a session, without me even disconnecting from the wifi network, where I would again need to switch back and forth to the 2 or 4 ending!
View 3 Replies
View Related
Dec 30, 2012
I connect a copper SFP on port 2 of WLC 5508 to a ASA 5510 firewall. The links between two devices are down. Since ASA 5510 only support 100 full, how do I change port speed on port 2 to 100.
View 8 Replies
View Related
May 16, 2013
We use a wlc model AIR-CT5508-K9 with eight built-in ports. I would like to know if it is possible to change the speed of these ports down to 100Mb. At this time, they are set to auto and 1000Mbps.
View 3 Replies
View Related
Jul 31, 2011
I had tried to connect my internet using a 10/100 standard Ethernet card but my net connection was fluctuating. My Brother who is a network engineer told me to switch back to 10 mbps from 100 mbps full duplex and he prayed if that might work. Luckily enough it worked and solved my purpose of delivering uninterrupted net connection.
View 1 Replies
View Related
Jun 17, 2011
nyway, I've had an internet connection set up at my house for quite some time, and recently I have noticed that my online games have begun to lag. And I know it is not due to my hardware, it is online-lag, like jumping, and almost teleporting to places. I play games like Battlefield 2, Battlefield 2142, Battlefield 2: Project Reality, and more.I have a 10mbps download and 1mbps upload, so that is an optimum speed for playing games like this, I know. And the connection is split between 3 computers in my home. (1 desktop and 2 laptops, all connecting wirelessely)I have all the modem, and router set up properly.. I just don't understand why I am having this lagging problem. If someone could explain it to me,
View 4 Replies
View Related
Apr 18, 2012
Im currently experiencing an intermittent connection on my office and we just upgraded from 4Mbps to 10Mbps. Latency is high when pinging commercial website like yahoo.com,it shoots up to 200sec. ISP router is connected to two HP Procurve Switch, then the workstation and servers. Already did a router/modem test and it failed, I advise our ISP to change the router but it were still experiencing the same problem. Network drop is also experience even after office hours, eventhough only few workstations are working.
View 1 Replies
View Related
Apr 14, 2012
Been wondering what would make a LAN only run on 10mbps. I recently experienced this on two clients sites. It won't just connect when I configure the LAN to run on 100mbps. Only connects on 10mbps. What could be responsible for this? Won't this affect the performance of ones application?
View 5 Replies
View Related
Dec 8, 2011
-I have a 10 mbps subscription.
-I use a router and connect two pcs on it,they use internet at the same time.
Q:will the speed be 5mbps on each computer? if so,is there a way to make it 10mbps each while they are both using the internet at the same time?
View 4 Replies
View Related
Nov 3, 2012
I have a 9-year old PPPoE DSL modem at home whose ethernet port is only 10mbps. For some reason I am unable to establish PPPoE connection on my E1000 when connected to this modem (PPPoE login is correct, as it works with a different router when connected to the same modem). Someone suggested that the problem may be that the DSL modem is unable to negotiate Ethernet connection because E1000's WAN port is 10/100mbps (autosensing failing?). The suggestion was to manually set the router's WAN port to 10mbps. Is there such a switch somewhere on the E1000 - I cannot find it in web admin console anywhere?
Any other guesses as to why the router and the modem cannot connect?
FWIW, the dsl modem is a SpeedStream 5360 E1000 hardware v 2.1; firmware 2.1.02
View 1 Replies
View Related
Jan 15, 2013
tell me if cisco 1921 onboard GigabitEthernets can reach 10Mbps with concurrent services, one GigabitEthernet interface as WAN interface, the other one as LAN interface.
View 2 Replies
View Related
Feb 26, 2013
when I connect my DIR-655 to the Motorola SB6141 cable modem I notice that the link speed LED on the cable modem never glows blue indicating a gigabit connection, it only glows amber indicating a lower negotiated speed. I am using a Cat6 cable between the two devices and have also tried a Cat5e cable.
When I try and force the WAN port speed to 1000Mpbs in the router interface the cable modem link speed will not light at all with no connectivity. Only resetting to Auto WAN port speed restores functionality albeit at the lower negotiated speed setting.
I'm running the DIR-655 rev B1 at 2.03NA firmware level.
I did connect the modem directly to my PC that uses an Intel Gigabit ethernet card and still had the lower connection indication (Amber) so it seems that the modem might be faulty.
View 4 Replies
View Related
Jan 9, 2013
I have a DIR-655 that I have been using for a while (b1 revision). and suddenly I noticed my wifi speed fluctuates constantly. My lenovo Y580 sees speed drop to 130 immediately and then it can slowly progress to 1 Mbps until the hardware is all rebooted. Same happens to my Nexus 7, Dell XPS M1530 and to my roku. I have updated to 2.07 (since 2.10 is advised to avoid). And I have attempted changing channels or factory refresh.What Firmware version is currently loaded? 2.07What region are you located?
What ISP Service do you have? Cable or DSL? Cable (link speed independent of internet speed)What ISP Modem do you have? Stand Alone or built in router? Separate Motorola ((link speed independent of modem)What ISP Modem make and model do you have? Does not matter, router issue.If this modem has a built in router, it's best to bridge the modem. Having 2 routers on the same line can cause connection problems.To tell if the modem is bridged or not, look at the routers web page, Status/Device Info/Wan Section, if there is a 192.168.0.# address in the WAN IP address field, then the modem is not bridged. Not bridged
Turn off all anti virus and firewall programs on PC while testing. 3rd party firewalls are not generally needed when using routers as they are effective on blocking malicious inbound traffic. Independent of issue, not a factor
Turn off all devices accept for one wired PC while testing. Wired works perfect.Check cable between Modem and Router, swap out to be sure. Cat6 is recommended. Wireless issue.
View 6 Replies
View Related
Jan 29, 2013
too many users know my security key. How can i change it?
View 1 Replies
View Related
Jun 2, 2011
how to do Mac cloning on a Dlink Router, I know I have to go to 192.168.0.1 admin page but from there, I dont know anything. I wanna clone my mac address so I can change my ip address. After I clone it, then what do I do to change my IP? Please dont say stuff like you dont need to mac clone to change IP. Mac cloning seems to be the only way to change my IP. EDIT: I changed my Mac, cloned it. Then I resetted my router but the I couldnt surft the internet anymore. I had to change back to my old MAC to get internet back.
View 1 Replies
View Related
Jan 21, 2011
I have a DIR-655 connected to a linksys switch via lan to lan. The 655 is on the other end of the house. I can not connect to the 655 to enable policies or make changes. I can connect for internet, thats all. I was told that I had to have the router IP close to the linksys (192.168.1.1). I wanted to change the ip address of the 655 to 192.168.1.2 . Every time I do this I can no longer connect to the 655 via lan. I have rebooted my computer and the 655. Nothing. I have to hard reset just to connect to it and start all over again.
View 14 Replies
View Related
Jul 3, 2011
I need a new ip address form my provider.I now that thy work with the mac address,How van i cahnge that in my dlink 655
View 5 Replies
View Related
