D-Link DIR-655 :: After IP Change Can't Connect Via LAN
Jan 21, 2011
I have a DIR-655 connected to a linksys switch via lan to lan. The 655 is on the other end of the house. I can not connect to the 655 to enable policies or make changes. I can connect for internet, thats all. I was told that I had to have the router IP close to the linksys (192.168.1.1). I wanted to change the ip address of the 655 to 192.168.1.2 . Every time I do this I can no longer connect to the 655 via lan. I have rebooted my computer and the 655. Nothing. I have to hard reset just to connect to it and start all over again.
how to do Mac cloning on a Dlink Router, I know I have to go to 192.168.0.1 admin page but from there, I dont know anything. I wanna clone my mac address so I can change my ip address. After I clone it, then what do I do to change my IP? Please dont say stuff like you dont need to mac clone to change IP. Mac cloning seems to be the only way to change my IP. EDIT: I changed my Mac, cloned it. Then I resetted my router but the I couldnt surft the internet anymore. I had to change back to my old MAC to get internet back.
I've searched high and low across the wide web, but I have found no real answer to this problem;Recently, I bought the DIR-655 because the gods of thunder decided to euthanize my old WAP. The original plan was to mate this up with a Tilgin VOOD-modem (modem and router in one; a heap of s**** in my uneducated eyes) in order to make networking within my appartment somewhat easier.
Got it safely indoors, plugged it in as the manual told me, and got it going (my old WAP was also a D-LINK, so the interface was somewhat familiar). Checked cabled connection, worked fine, and I got the wireless-bit to function as well. But then I, or my Xbox 360 to be right on the money, encountered a little problem. As I understand from a little bit of research, I found out that this was a dreaded phenomenon known as
"Moderate NAT"
Before I got the old WAP indoors, I used the onboard router in the TILGIN to do the switching. I used to have this problem back then also, but solved it by opening some of the ports on the modem. Then it switched to "Open NAT", and worked like a charm. Now however, I have ran into a problem I can't dig myself out of. I have tried DMZ, opening numerous ports all the way to the full monty, but I can�t get that NAT to wander into the more acceptable range. And then it became clear that the internet on my laptop was somewhat amputated as well; simple youtube-videos became harder to load (sometimes it actually had to stop for extended streaming!), and this is not acceptable on a 20 mbt DSL-line!
I play my xbox 360 wired threw my DIR-655 router and when I play online I notice on most games that my nat is strict. Does anyone know how I can change my nat on my router.
After my dir-655 recently bought the farm, I picked up a NIB 601 at a local computer mall for about $20. The drawback is that "local" for me means that the router is in Chinese.
Is there any way for the web interface language to be changed to English?
Is it possible to change from WPA2 to WEP security without making international phone calls to Peggy?While I was away from home our WIFI went down, my daughter was able to get the network back but in the process she changed the security. The biggest problem is that my G3 iBook can see the network but can't sign in.
So I'm on the 100mbps virgin fibre optic broadband, and for the past couple of days, every now and again my speed drops drastically. It's not the Internet, because I've tested it on my laptop both wireless and plugged in. Even my phone and iPad are getting higher speed.
When I first got the internet(About a week ago) my download speed was 100+ mbps, but now my Link speed is constantly at 10mbps, even if I set my NIC to 1gbps full duplex, I've tried disabling and re enabling, I've tried uninstalling and reinstalling drivers, updating drivers. Restarting the router, starting it in Modem mode.
The device is working just fine but I just want to change the password but it failed. I opened my web browser enter 192.168.0.1 then logged into the admin account then put in the new password for both admin and user, clicked save setting...it asked for rebooting the device I let it rebooting. Everything went fine. I was able to log in both the admin and user acc with the new password. The only problem is that my PC can still connect to the network using the old password? I expect that the PC will need to use the new password to access the network but this is not the case.
Region : Hongkong Model : TL-WR740N Hardware Version : V4 Firmware Version : ISP : PCCW
Just bought the router in Hong Kong to connect to my Mac. Typed in [URL] and everything is in Chinese with no link that I can see to change it to English. Is it possible to change the language?
Had to reset out DIR-655 router. This ended up changing our network password. Unfortunately, my DAP-1522 was not informed of this change and it will not connect to my Directv receiver now. I attempted to log into the bridge to change the password and it will not let me in. I attempted to reset the DAP in hopes that I would just be able to start over from scratch, but no dice (Assuming that I did it correctly)
I am having a problem which I can't seem to find a way around. I have a DIR-615 E3 that I'm unable to get IPv6 to work properly on.I'm connecting to IPv6 over PPPoE, and I'm unable to change the 'IPv6 LAN Address' to an IP my provider has given me. They've provided a native address in the 2607:: range, however on the router it's stuck at a 6to4 IP which is NOT what they've given me (2002:CEF8:8B79:: IP).
I'm thinking of buying a new router that either has better IPv6 support, or one that supports OpenWRT and working my way through that.
I've been having issues with my DIR-655 - the speeds are super slow. In the past, I've been able to restart the modem, and my speeds would be acceptable, but now a restart doesn't change the speeds I'm getting from speed test.net. I know it has to do with the router, because when I directly connect to the modem, my speeds are great.
-Speeds WITH router: -Speeds WITHOUT router:
And like I said, in the past I could restart the router, to get similar speeds to just my modem, but it doesn't work that way anymore.
I would like the ability to change the default password. Currently, when I change the default password and save the config via the web interface, neither the original password, or the new password work. I am forced to reset the device to the default config to regain access to the device.
i am using a D-Link 2730u, was trying to change the username and password for the router but it keeps saying that ACS URL is required, there is a place where i can put one but even after goggling it for a bit i didn't understand what should i put in there?
Region : China Model : TL-WR741N Hardware Version : V4.20.0 Firmware Version : ISP :
I am American living in China. My Chinese reading is not so good, I am still learning. The interface for my router comes up in Chinese. Is there a way to change the language to English? So far, all I can do is get the set-up interface through IE, but I can not set it up!
I bought this wireless router the other day in order to get internet access on my Nintendo Wii. I set it up using the CD and followed all the instructions (made a password, wrote down the key, etc.) - and my Wii CAN detect it, but when I type in the key on the Wii I get an error message. I looked online and they said the way to fix that specific error is to "change the channel" on the router to 1 or 11. (It is currently 6). I type in my IP into the browser like I'm supposed to (the default IP of the router), but ALL the options on the page are greyed out and nothing is click-able. Here's a screenshot
I am using D-Link DIR-615, I need to ask is it possible that i change the error page "Forbidden Web Access" ? I have blocked some websites and i dont want ppl know that it is blocked by router because in D-Link default error msg it is clearly mentioned that " This page is not included in the router's Allowed Web Site List". Is it possible that i redirect error page to some other site? or change error message?
I just bought a DIR 615 (firmware 4.0) which I am using as an access point linked to a Netopia router. The Netopia has QoS enabled and needs to keep it, however I was hoping to use the DIR615 without QoS. I am using a ReadyNas Duo as storage for music, videos etc.Now, here are my issues which I think are all linked.
1) I have a very slow connection wireless, between 1'500 and 2'000kbits/sec download. This was not the case with my very old Linksys router
2) When I try to rip a CD from iTunes to the NAS, it brings up error messages of lost connection and impossibility to rip in the middle of the songs. I did not have that problem with the Linksys router neither.
3) I would like to change the QoS parameters to see how it affects this connection issue, as well as change other Wifi parameters, but they show up as greyed out and I can't change them. (I feel that the DIR 615 might inherit some parameters from the main router, since it is used as an Access Point).
Lately, Ive been trying to change my router DNS to OpenDNS. Somehow, after changing it, I couldnt access the router page at 192.168.0.1, getting the error 500 message. I unplugged and plugged the router with no effect. Im using a dlinkddns.com dynamic IP, and have a few ports forwarded for my DVR. The router model is DIR 615. want to change the DNs for speed and filtering purposes.
Region : UnitedKingdom Model : TD-W8951ND Hardware Version : V5 Firmware Version : 5.0.0 Build 120703 Rel.29030 ISP :
I have setup some static addresses but now some of them need to change... But I can't see how to amend the DHCP table..There must be a way of doing this beyond altering the DHCP range so I can put them all in againLAN Setup.JPG.
Is there any way to change the subject line of the email alerts that are sent? Right now mine are coming with the MAC address, date and time. I would like to remove the MAC address and date and time so that I can sort them into one folder when I sort my email by subject.
First is it possible to change the length that new files will be created? Right now it creates 1 minute chunks which becomes a pain in the butt to manage. I would really like to set the length to 10min or even 60min chunks as one minute is just to short. I use the camera for constant recording and do not plan on puttin in a computer to record to due to logistics.
Secondly, is there software that will manage these files? That is pull down from the cameras SD and archive then allow you to simply play from any location via mouse or time picker?
I have used professional security systems in the past and know that this is just an entry home consumer camera but was hoping it had a little more functionality, as it stands the built in SD recording is almost useless without some sort of management software.
