D-Link DIR-615 :: Unable To Change IPv6 LAN Address To An IP
Jun 23, 2012
I am having a problem which I can't seem to find a way around. I have a DIR-615 E3 that I'm unable to get IPv6 to work properly on.I'm connecting to IPv6 over PPPoE, and I'm unable to change the 'IPv6 LAN Address' to an IP my provider has given me. They've provided a native address in the 2607:: range, however on the router it's stuck at a 6to4 IP which is NOT what they've given me (2002:CEF8:8B79:: IP).
I'm thinking of buying a new router that either has better IPv6 support, or one that supports OpenWRT and working my way through that.
View 1 Replies
ADVERTISEMENT
Jul 3, 2011
I need a new ip address form my provider.I now that thy work with the mac address,How van i cahnge that in my dlink 655
View 5 Replies
View Related
Jul 6, 2012
Hardware version: A4, Firmware version: 1.35NA.
The device is working just fine but I just want to change the password but it failed. I opened my web browser enter 192.168.0.1 then logged into the admin account then put in the new password for both admin and user, clicked save setting...it asked for rebooting the device I let it rebooting. Everything went fine. I was able to log in both the admin and user acc with the new password. The only problem is that my PC can still connect to the network using the old password? I expect that the PC will need to use the new password to access the network but this is not the case.
View 8 Replies
View Related
Feb 24, 2013
Region : UnitedKingdom
Model : TD-W8951ND
Hardware Version : V5
Firmware Version : 5.0.0 Build 120703 Rel.29030
ISP :
I have setup some static addresses but now some of them need to change... But I can't see how to amend the DHCP table..There must be a way of doing this beyond altering the DHCP range so I can put them all in againLAN Setup.JPG.
View 1 Replies
View Related
Apr 26, 2011
Using Android phone and have to set up Port Forwarding to access the cameras. I have to change the IP Address to a static one instead of the one issued by the Router. How do I change the IP Address of the camera to one outside the DHCP range?
View 14 Replies
View Related
Aug 27, 2012
I found this firmware 2.05WW for DIR 655 rev B1, I couldn't find any change logs or anything on the net about it.
View 3 Replies
View Related
May 2, 2012
Why can't I set an IPv6 address here (WS-2960-48TC-L latest IOS)
View 7 Replies
View Related
Dec 7, 2010
I've got older SOHO97 which I want to use as a backup for Cisco 800 but I can not find any information if it actually supports IPv6. Neither the data sheet [URL] nor the Cisco Feature Navigator [URL] suggest it has any IPv6 support at all.
View 1 Replies
View Related
Apr 10, 2013
I have a Swann Communication security camera system with their DVR8-4000 hooked to an IPv4 router, connected to the Internet using the new HughesNet Gen4 service. The Swann DVR wired to my router requires a static IP address. HughesNet Gen4 is implemented with IPv6 and I am told that it does not accommodate an IPv4 type static address.
I have discussed the issue with both company’s technical support. HughesNet Gen4 reps recognize the issue and may support static addressing in the future, but not now. Swann reps will not modify their implementation because of the relatively small Gen4 market. The Swann rep suggested that replacing my IPv4 router with an IPv6 router might resolve the “static IP address” issue.I am looking at several Linksys IPv6 routers including the EA4500 SMART WiFi Wireless Router N900, but know too little about IPv4, IPv6 and router/static addressing to proceed unassisted.
1) can I implement a static address with an Linksys IPv6 router cdonnected to Gen4?
2) Which Linksys routers offer IPv6 support?
3) How does one go about setting an IPv6 static address using HughesNet Gen4 on a Linksys router?
View 1 Replies
View Related
May 23, 2012
I have seen other discussions regarding Static MAC address entries on IPv4, but what of IPv6?We have MS NLB solutions and they are working fine. We have Cisco 6509/6504, Version 12.2(33)SXI5
But then we have a new one for a new ActiveDirectory solution, and on those networks we have implemented IPv6.
How is Static MAC address entries and MS NLB solved in IPv6 (i.e arp ip.ip.ip.ip mac.mac.mac ARPA gi1/1). I can't seem to find much examples or documentation on this? Is it replaced with another function?The reason I ask is twofold.
1. I really want to know
2. The NLB cluster seem to drop IPv6 traffic at even intervals, witch seems to correspond with NLB transition.
View 1 Replies
View Related
Oct 9, 2011
below is my sanitized ASA 5510 config. got an IPv6 T1 from at&t and im unable to pass any traffic from my LAN clients out.
:
ASA Version 8.2(2)
!
enable password PoBmYYxuAzCciKRA encrypted
[Code].....
View 6 Replies
View Related
Nov 9, 2012
I have a virtual machine running in my desktop which connected on the gigabit lan port on EA4500 with firmware 2.0.37.What I want to be able to do forward a port that came from an external ipv4 address to the ipv6 address and a different port to my virtual machine (to remote desktop port 3389).The reason I want to convert the traffic to ipv6 is because virtual machine is running vpn and is not reacheable through ipv4 (unless bunch of routes are setup and things get complicated etc). I verified my phsical server and virtual server get both ipv6 ip addresses through ipv6 tunnel from comcast. Without tunneling I could not get ipv6 setup using automatic mode with comcast, it simply did not work for some reason.
View 1 Replies
View Related
Jun 25, 2012
When I check for firmware updates for my DIR-825 I get a return that there are none.How do I update for for ipv6 then?
View 5 Replies
View Related
May 10, 2010
I am using my DIR-825 as a switch and AP. I have turned off DHCP and plugged the internet into the lan-1 port. This works perfectly for IPv4, but I cannot get IPv6 to work. On the outside there is native IPv6 running radvd. How should I configure IPv6 on my DIR-825?
View 2 Replies
View Related
Apr 17, 2012
Unfortunately I didn't discover any configuration switches concerning an IPv6 firewall! So the important question is: Is there any firewall implemented at all? And if so, does it confirm to RFC6092.
View 14 Replies
View Related
May 5, 2011
Will there be a way sometime in the future to add static IPv6 routes? I have a routed /64 and a routed /48 from a tunnel broker that terminates on my DIR-815, and I want to hang the /48 off of another router that I have attached to my LAN interface(goes to my home lab setup that I use for my job). I could just move the tunnel endpoint to the other router, but I like having IPv6 access for all my other PCs on the LAN segment.
View 1 Replies
View Related
May 17, 2012
I'm still using 2.00NA.It seems that whenever I connect to a particular www3 webpage, my modem and router end up rebooting shortly thereafter. This has happened a few times. The modem's log shows in this order1. No Ranging Response received ,2. Unicast Ranging Received Abort Respone ,3. MIMO Event.I've tried to figure this out. My search on the MIMO event revealed one post about IPv4 and IPv6. This indicates to me that I should probably be upgrading the firmware and configuring its use for IPv6 compatibility.If I upgrade to FW 2.30NA, how should I configure the IPv6, i.e., which parameters should I use?
View 6 Replies
View Related
Sep 19, 2010
I've had my DIR-615 up for several months, and it's been faultless except for one thing. I have router in front of it and only use the 615 as a switch and AP. My main router provides IPv6 access through a 6to4, using radvd to broadcast to the rest of the network.
Whatever setting I set the 615 to for IPv6, it always sends out a default route. On rare occasion, it'll interfere with the correct route from my main router (whose router preference is set to high, instead of medium). Even in local-only mode, the 615 sends out a default route. It's an E1 with the 5.00NA firmware, which I believe is the latest.
I'd really like to disable the advertisements from the 615 altogether, while keeping L2 IPv6 support on the wireless and all. I picked this router explicitly because many routers don't work with IPv6 over WiFi, but it'd be nice to get it working perfectly. If there aren't any ways to do this, is there a place that I can download the source for the firmware?
View 4 Replies
View Related
Jul 19, 2012
We have some technical issue with IPv6 router configuration[DLINK 655] when we try to connect it with ISP provided static IPv6 connection.
[Code]...
View 9 Replies
View Related
Oct 14, 2011
I have a d link dir 615 "ipv6 ready". My internet provider give tome a native ipv6 /48. I configure the router with my ipv6 /48 address the internal propagation of the address is good.
On the status ipv6 page all seems OK marked "connected" but I can't have an ipv6real connection and my provider say to me that i am not connected.
Is there a known problem of connection between an public /48 and the internal /64 and if so could it be corrected.
View 12 Replies
View Related
Nov 9, 2012
I set up the IPv6 on EA2700 (running firmware v1.1.39), and all the wired clients can get an IPv6 address, assigned by the router, without issue.However, all the wireless clients seem to unable to get an IPv6 address. If I connect a laptop to the router both wirelessly and with an ethernet cable, then the ethernet NIC gets an IPv6 IP but not the wireless NIC.
View 9 Replies
View Related
Jan 17, 2013
How exactly do you change your IP Address?
View 8 Replies
View Related
Sep 9, 2011
I'm wondering is there a way that i could actually change the IP address of a computer based on its MAC Address that is connected to a network via switch only ? By running some bat file ? I only manage to change a target computer ip,dns,subnet via running the bat file on the physical computer but not through a network with switch.
View 11 Replies
View Related
Sep 6, 2011
My IP address was stolen. Someone sent me a file that I was expecting. It had a very misconcieving title. I opened it and it wouldn't work, but I let it slide. A week or two later I found pictures of myself on a forum from a hacker. The file I had opened had been a virus that hacked into my webcam. This creep told me that this had spread to 1000+ people and they all had my IP address. I am so scared! If everyone has my IP address anything could happen. How do I change my IP address without it messing up other settings in my computer and how do I remove this virus from my computer?
View 3 Replies
View Related
Mar 24, 2013
Recently I wanted to setup IPv6 for my home network. I signed up for tunnelbroker.net service and was provided with IPs. Then I configured the IP address in my DIR-615. But It's not working..
Screenshot of IPv6 config (router) : Screenshot of my Win 8 network Config : I also tested at [URL] but failed...
View 3 Replies
View Related
May 16, 2013
I currently have ipV4 as the setting on my DIR-825. Other posts seem to want ipV6 which is more secure but is not possible with a DIR-825 Rev A1. I have two routers, a primary router (DIR-825 Rev B1) capable of ipV6 and a secondary router (DIR-825 Rev A1). If I implement ipV6 on the Rev B1 router but keep ipV4 on the secondary router, will this improve the security, or will it just mess things up so nothing works?Certain devices (cell phones and most Tablets) don't deal with ipV6 very well at all. The ones I have tested flat don't connect to the wireless network if the router is set at ipV6. Is ipV4 adequate for a Home/Small Business Network when trying to implement Remote Access and VPN?
View 2 Replies
View Related
Mar 30, 2012
I am having trouble with a DAP-1522 in AP mode dropping IPv6 packets. It is running in AP mode to supply connectivity to a number of laptops + a 2nd DAP-1522 in bridge mode. The laptops are able to get IPv6 router advertisements from the same wired network the DAP-1522 is plugged into, but they get nothing when connection to the wireless. Tcpdump sees no router adv's coming over the wireless interfaces when sniffing.This appears to be something others have hit as well url...
View 3 Replies
View Related
Jun 9, 2011
I have a Dlink DIR-825 B1 with firmware 2.05NA. I recently reset it to factory defaults to make sure I didn't misconfigure something.
I have been struggling to get a IPv6 in IPv4 tunnel working with tunnelbroker.net. I think the issue is a problem with the router itself and i'm not sure how to get it fixed.
All of my machines were getting IPv6 addresses (both windows, mac, linux) but none of them seemed to work. All I was able to do was ping the gateway itself using the local lan address. In each case they were missing a default IPv6 route. If I added a default route then it would work.
I started looking at the packets using a network sniffer and the Router Advertisements all had a Router lifetime value of "0" which is RFC4816 speak for "don't use this router as the default router". So Windows/Linux is exactly right by not setting a default route.
The strange thing was that when I reboot the router I would briefly get a router advertisement with a lifetime of 1800s, the corrert prefix and dns server but then another router advertisement would come along 5 seconds later with a router advertisement of 0.
I have TCP' Other observations
... using 6to4 I would get working IPv6 address. The difference again seemed to be the Router Lifetime. But I want to use a permanent tunnel. I have found 6to4 unreliable.
... the router never responds to router solicitations. It only sends a router advertisement when it wants to.
... the router never responds to DHCPv6 when that is configured.
View 1 Replies
View Related
Dec 30, 2012
I tried using mac changing programs and tried to change it from the registry but none of the methods worked for me.
View 3 Replies
View Related
Oct 11, 2011
I have a TP-Link device TL-WR340G Wifi Device. I connect a PC through one of the LAN ports.Mow my WiFi router's MAC address has not been registered at my ISP system. I need to find a way to 'change' my Routers MAC address to another MAC address. The cloning doesn't work. I need to change my Router's LAN MAC address.
View 6 Replies
View Related
Jun 21, 2012
How to change my routing address 192.168.1.1 to 192.168.0.1?
View 1 Replies
View Related
Jul 24, 2012
i always get ban i czero due to high ping is there any way i can change my ip address so i can get in server again
View 8 Replies
View Related
Jun 20, 2012
I'd like to register another account in a forum to comment anonymously so I need a different IP address for browsing.I remember that I had been trying this long time before but it was not easy to make it. Using proxy website is useless because the speed is very very slow. Is there any way to painlessly, easily change IP to browse websites?
View 4 Replies
View Related
