D-Link DIR-655 :: FW 2.30NA - Way To Configure IPv6?
May 17, 2012
I'm still using 2.00NA.It seems that whenever I connect to a particular www3 webpage, my modem and router end up rebooting shortly thereafter. This has happened a few times. The modem's log shows in this order1. No Ranging Response received ,2. Unicast Ranging Received Abort Respone ,3. MIMO Event.I've tried to figure this out. My search on the MIMO event revealed one post about IPv4 and IPv6. This indicates to me that I should probably be upgrading the firmware and configuring its use for IPv6 compatibility.If I upgrade to FW 2.30NA, how should I configure the IPv6, i.e., which parameters should I use?
View 6 Replies
ADVERTISEMENT
Nov 23, 2011
I am using 3550 with c3550-ipservicesk9-mz.122-44.SE6.bin. Have successfully run ipv6 commands on global and interface, however getting below error while configuring "ipv6 router ospf 1" :SW1(config)#ipv6 router ospf 1 % Failed to create routing protocol ospf
Command syntax help says its configurable but its not configuring ipv6 OSPF.
View 3 Replies
View Related
Jul 12, 2011
To show up the ASA as a hop in a traceroute, one can use the 'set connection decrement-ttl' feature in a policy map.During my tests I recognized, that this behaviour only affects IPv4 traffic.
An IPv6 traceroute still does not show the ASA as a hop.How can I configure the ASA to show up as a hop in an IPv6 traceroute?The ASA is a 5520 with v8.4(1) installed.
View 7 Replies
View Related
Jul 9, 2012
Do you know when will be possible to manual configure ipv6 settings? I have all parameters from my ISP but the settings on the router are only automatic and 6rd. Is it possible to enable this in future firmwares?
View 1 Replies
View Related
Jun 25, 2012
When I check for firmware updates for my DIR-825 I get a return that there are none.How do I update for for ipv6 then?
View 5 Replies
View Related
May 10, 2010
I am using my DIR-825 as a switch and AP. I have turned off DHCP and plugged the internet into the lan-1 port. This works perfectly for IPv4, but I cannot get IPv6 to work. On the outside there is native IPv6 running radvd. How should I configure IPv6 on my DIR-825?
View 2 Replies
View Related
Apr 17, 2012
Unfortunately I didn't discover any configuration switches concerning an IPv6 firewall! So the important question is: Is there any firewall implemented at all? And if so, does it confirm to RFC6092.
View 14 Replies
View Related
May 5, 2011
Will there be a way sometime in the future to add static IPv6 routes? I have a routed /64 and a routed /48 from a tunnel broker that terminates on my DIR-815, and I want to hang the /48 off of another router that I have attached to my LAN interface(goes to my home lab setup that I use for my job). I could just move the tunnel endpoint to the other router, but I like having IPv6 access for all my other PCs on the LAN segment.
View 1 Replies
View Related
Sep 19, 2010
I've had my DIR-615 up for several months, and it's been faultless except for one thing. I have router in front of it and only use the 615 as a switch and AP. My main router provides IPv6 access through a 6to4, using radvd to broadcast to the rest of the network.
Whatever setting I set the 615 to for IPv6, it always sends out a default route. On rare occasion, it'll interfere with the correct route from my main router (whose router preference is set to high, instead of medium). Even in local-only mode, the 615 sends out a default route. It's an E1 with the 5.00NA firmware, which I believe is the latest.
I'd really like to disable the advertisements from the 615 altogether, while keeping L2 IPv6 support on the wireless and all. I picked this router explicitly because many routers don't work with IPv6 over WiFi, but it'd be nice to get it working perfectly. If there aren't any ways to do this, is there a place that I can download the source for the firmware?
View 4 Replies
View Related
Jun 23, 2012
I am having a problem which I can't seem to find a way around. I have a DIR-615 E3 that I'm unable to get IPv6 to work properly on.I'm connecting to IPv6 over PPPoE, and I'm unable to change the 'IPv6 LAN Address' to an IP my provider has given me. They've provided a native address in the 2607:: range, however on the router it's stuck at a 6to4 IP which is NOT what they've given me (2002:CEF8:8B79:: IP).
I'm thinking of buying a new router that either has better IPv6 support, or one that supports OpenWRT and working my way through that.
View 1 Replies
View Related
Jul 19, 2012
We have some technical issue with IPv6 router configuration[DLINK 655] when we try to connect it with ISP provided static IPv6 connection.
[Code]...
View 9 Replies
View Related
Oct 14, 2011
I have a d link dir 615 "ipv6 ready". My internet provider give tome a native ipv6 /48. I configure the router with my ipv6 /48 address the internal propagation of the address is good.
On the status ipv6 page all seems OK marked "connected" but I can't have an ipv6real connection and my provider say to me that i am not connected.
Is there a known problem of connection between an public /48 and the internal /64 and if so could it be corrected.
View 12 Replies
View Related
Mar 24, 2013
Recently I wanted to setup IPv6 for my home network. I signed up for tunnelbroker.net service and was provided with IPs. Then I configured the IP address in my DIR-615. But It's not working..
Screenshot of IPv6 config (router) : Screenshot of my Win 8 network Config : I also tested at [URL] but failed...
View 3 Replies
View Related
May 16, 2013
I currently have ipV4 as the setting on my DIR-825. Other posts seem to want ipV6 which is more secure but is not possible with a DIR-825 Rev A1. I have two routers, a primary router (DIR-825 Rev B1) capable of ipV6 and a secondary router (DIR-825 Rev A1). If I implement ipV6 on the Rev B1 router but keep ipV4 on the secondary router, will this improve the security, or will it just mess things up so nothing works?Certain devices (cell phones and most Tablets) don't deal with ipV6 very well at all. The ones I have tested flat don't connect to the wireless network if the router is set at ipV6. Is ipV4 adequate for a Home/Small Business Network when trying to implement Remote Access and VPN?
View 2 Replies
View Related
Mar 30, 2012
I am having trouble with a DAP-1522 in AP mode dropping IPv6 packets. It is running in AP mode to supply connectivity to a number of laptops + a 2nd DAP-1522 in bridge mode. The laptops are able to get IPv6 router advertisements from the same wired network the DAP-1522 is plugged into, but they get nothing when connection to the wireless. Tcpdump sees no router adv's coming over the wireless interfaces when sniffing.This appears to be something others have hit as well url...
View 3 Replies
View Related
Jun 9, 2011
I have a Dlink DIR-825 B1 with firmware 2.05NA. I recently reset it to factory defaults to make sure I didn't misconfigure something.
I have been struggling to get a IPv6 in IPv4 tunnel working with tunnelbroker.net. I think the issue is a problem with the router itself and i'm not sure how to get it fixed.
All of my machines were getting IPv6 addresses (both windows, mac, linux) but none of them seemed to work. All I was able to do was ping the gateway itself using the local lan address. In each case they were missing a default IPv6 route. If I added a default route then it would work.
I started looking at the packets using a network sniffer and the Router Advertisements all had a Router lifetime value of "0" which is RFC4816 speak for "don't use this router as the default router". So Windows/Linux is exactly right by not setting a default route.
The strange thing was that when I reboot the router I would briefly get a router advertisement with a lifetime of 1800s, the corrert prefix and dns server but then another router advertisement would come along 5 seconds later with a router advertisement of 0.
I have TCP' Other observations
... using 6to4 I would get working IPv6 address. The difference again seemed to be the Router Lifetime. But I want to use a permanent tunnel. I have found 6to4 unreliable.
... the router never responds to router solicitations. It only sends a router advertisement when it wants to.
... the router never responds to DHCPv6 when that is configured.
View 1 Replies
View Related
Apr 20, 2013
Region : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 121225 Rel.37950n
ISP : Comcast
just upgrade to the latest firmware and was checking to see if I had IPv6 going with the router but it seems like it's not enabled?I went into my local area network properties and it shows checked and obtain automatically.went into the router ipv6 support tab and it shows:
IPv6 Status
WAN
Connection Type:
DHCPv6
IPv6 Address:
[code].....
View 1 Replies
View Related
Sep 1, 2011
got the DIR-655 for gaming not knowing about LAN and WAN can any tell me if i can config this router to work properly with my broadband i have ONT that the router connects to
View 1 Replies
View Related
Aug 22, 2012
I have prolem with Dir615 I doesn't know how to configure it to use for file sharing outside Lan. The problem with Dir615 I'm sure because when I swicth Dir615 to Dir100 it's works perfectly. Is there any magic box where should I mark tick?
View 3 Replies
View Related
Jan 4, 2013
Region : Others
Model : TL-MR3040
Hardware Version : V1
Firmware Version : 3.12.11 Build 120328 Rel.63398n
ISP : CityCell Zoom (in Bangladesh)
I bought a MR3040 Router & I have a ZTE AC682 (EVDO) Modem. I found my modem's model in Modem Compatibility List (Other Country, Indonesia & Singapore).
1st time The router showing Unknown Modem.
Then I tried with .bin file upgrade. The Router Showing Identifying .... Then I tried with firmware Upgrade. But Still Showing Identifying ....
My Systems Log as below
code...
View 5 Replies
View Related
Jul 28, 2012
I am replacing an A3 that's slowing dying with a B1. I understand the Firmware versions are different but I was curious if I can save the config file from the A3 and load it into the B1 ? I don't know if the config file includes the Firmware....
View 2 Replies
View Related
May 16, 2013
I updated my dir-655 firmware to 1.36WW after the update I the router has been restored to factory settings and every time I try to change any setting it gives me: "ap should not be locked before configuring". I cant change set any configuration, cant change even the router time!I logged in to the router as admin and left the password blank.
View 2 Replies
View Related
Jul 10, 2011
I would like to know how to configure my DIR-600s firewall UDP Endpoint Filtering. I ve read some guides and I ve got to configure this to Endpoint Independent in order to play League of Legends. The problem is that I can see the option Firewall & DMZ but then I don't see the UDP or TCP Endpoint Filtering options.
View 1 Replies
View Related
Oct 11, 2011
I had got a internet connection from ISP.
The etho mode is 10 mbps half duplex.
i have a router of dlink DES-1008D (wired switch ).
I want to configure a home wired network so I can connect my multiple system .
My ISP requires to configure me static ip in the ip configuration .
They have given us
IP address x.y.z.a
subnet mask 255.255.255.0
Default Gateway x.y.z.1
and DNS server name's
Now what settings I need to done to use my router ?
View 1 Replies
View Related
Apr 2, 2013
I have Dlink DWL - 2000AP+.
What I want to do is, to reproduce WiFi signal (from TP-LINK modem) by repeating with D-Link Wireless Access Point.
Here is how web interface looks. There is an option for repeating:
After clicking Site Survey I see all list of available networks. When I select one of them, the D-link saves changes then reboots. After that, Windows shows me something like that on available WiFi networks list:
<Repeated network name> 2
The problem is, when I connect to this network, Windows connects directly into root source, not to my WAP (I see this with inSSIDer utility).
View 1 Replies
View Related
Mar 13, 2012
I found out that I cant access my modem (TP-Link W8901G) config page at 192.168.1.1. I was pretty sure my ID and password is correct since I never changed them. It is also unlikely that the password got changed by other people who are stealing my Wi-Fi as I turned my WLAN on only when I requires the connection then it get turned off afterwards.
View 5 Replies
View Related
Aug 23, 2011
My apartment already has internet provided to all of the rooms, but I'm trying to set up my router as a wireless access point. I tried disabling DHCP on the router, but then I wasn't able to get any internet access at all. Does this device not support bridge mode?
View 5 Replies
View Related
Oct 7, 2011
How can I configure DCS 910 webcam if I don't have the software CD?
View 4 Replies
View Related
May 15, 2012
We have 6 sites which are connected through E1 links.All sites connected from HQs.
Site A is HQs.
Sited B, C, D, E, and F are Branches.
Site A is directly connected with site B, C, D and E.
Site D is connected with Site F.
Now we have another redundant E1 link for site C and Site F.we are using Static Routes.i have configured Qualified-next-hope on Juniper Router but i am unable to configure IP SLA on Site C Cisco 2951 with IOS 15.0 router.is there another solution for my scenario plz share with me for Redundant Link.
View 1 Replies
View Related
Jul 11, 2012
I've got a 881 working with a 3G Card. Even the Cisco 7965 phone is working well off it. Looking for good doc for configuring the 3G interface as a backup link to Comcast?
View 2 Replies
View Related
Nov 20, 2011
How can I configure my TP-Link router TD-W8950ND act as an access point? I'll be connecting it to a main router which is connected to the ISP.
View 1 Replies
View Related
Jan 29, 2011
I'd like to give my DIR-655 (rev. A4, firmware 1.32) to my brother for use as a repeater, to work with the weak signal in his apartment. But I don't see any way to configure the device to join an existing wireless network. Am I wasting my time?
View 7 Replies
View Related
Feb 3, 2013
Region : France
Model : TD-W8151N
Hardware Version : V3
Firmware Version : latest
ISP : OrangeF
Received today my modem, configured it with some effort but it works... Now i'm trying to save ma config file (rom-0) using web interface, and when clicking on Maintenance > Firmware, i'm always getting:bug.jpg Seems to be a big bug
View 4 Replies
View Related
