D-Link DIR-615 :: Disable IPv6 Stateless Advertisement?
Sep 19, 2010
I've had my DIR-615 up for several months, and it's been faultless except for one thing. I have router in front of it and only use the 615 as a switch and AP. My main router provides IPv6 access through a 6to4, using radvd to broadcast to the rest of the network.
Whatever setting I set the 615 to for IPv6, it always sends out a default route. On rare occasion, it'll interfere with the correct route from my main router (whose router preference is set to high, instead of medium). Even in local-only mode, the 615 sends out a default route. It's an E1 with the 5.00NA firmware, which I believe is the latest.
I'd really like to disable the advertisements from the 615 altogether, while keeping L2 IPv6 support on the wireless and all. I picked this router explicitly because many routers don't work with IPv6 over WiFi, but it'd be nice to get it working perfectly. If there aren't any ways to do this, is there a place that I can download the source for the firmware?
View 4 Replies
ADVERTISEMENT
Feb 15, 2011
i tried to disable the ipv6 using the regedit and all and i restarted my pc but when i check the local network are connection and properties the ipv6 is still checked.
View 8 Replies
View Related
Jun 17, 2012
I want to learn that,on cisco switch (2950,3600,6500 series) IpV6 default open? İf It comes open on default,how to disable?
View 19 Replies
View Related
Feb 24, 2013
I have a Windows 7 64 Bit machine, and I cannot find a way to disable the IPv6 Loopback. I looked at the article at How to disable IP version 6 or its specific components in Windows and shows how to set HKEY_LOCAL_MACHINESYSTEMCurrentControlSetServicesTcpip6ParametersDisabledComponents to various values – but none of these seems to disable IPv6 Loopback. I attempted setting this value to 0xffffffff and 0x20 – restarting my computer after each change, and I still do not get this disabled.
I am using another software called Webdriver or Selenium that gives errors when debugging if IPv6 Loopback is not disabled. It seems to attempt to connect to [::1]:7055 and fails. Is there a way to force it to connect to 127.0.0.1.
View 2 Replies
View Related
Jan 14, 2013
So I've realized that my parental controls were being ignored by the computers, at first I figured my son had found a work around to by-pass. But reading through the forums today, I've found that IPv6 being enabled might be the cause of my issue. So I'm currently sitting at work and connected to my router remotely, but for the life of me, can't see where to disable this option. Using the Smart Wi-Fi interface, closest I can get is "Connectivity, Internet Settings, IPv6 but everything is grayed out and no option to edit this.
View 9 Replies
View Related
May 21, 2011
Does ASA 5500 has stateless filter to drop packet even when 3-way handshake is finished
For example,
1: 3-way handshake is done
2:client send data to server
3:I apply a statless filter to the incoming interface to drop the packet from the client
View 3 Replies
View Related
Jun 25, 2012
When I check for firmware updates for my DIR-825 I get a return that there are none.How do I update for for ipv6 then?
View 5 Replies
View Related
May 10, 2010
I am using my DIR-825 as a switch and AP. I have turned off DHCP and plugged the internet into the lan-1 port. This works perfectly for IPv4, but I cannot get IPv6 to work. On the outside there is native IPv6 running radvd. How should I configure IPv6 on my DIR-825?
View 2 Replies
View Related
Apr 17, 2012
Unfortunately I didn't discover any configuration switches concerning an IPv6 firewall! So the important question is: Is there any firewall implemented at all? And if so, does it confirm to RFC6092.
View 14 Replies
View Related
May 5, 2011
Will there be a way sometime in the future to add static IPv6 routes? I have a routed /64 and a routed /48 from a tunnel broker that terminates on my DIR-815, and I want to hang the /48 off of another router that I have attached to my LAN interface(goes to my home lab setup that I use for my job). I could just move the tunnel endpoint to the other router, but I like having IPv6 access for all my other PCs on the LAN segment.
View 1 Replies
View Related
May 17, 2012
I'm still using 2.00NA.It seems that whenever I connect to a particular www3 webpage, my modem and router end up rebooting shortly thereafter. This has happened a few times. The modem's log shows in this order1. No Ranging Response received ,2. Unicast Ranging Received Abort Respone ,3. MIMO Event.I've tried to figure this out. My search on the MIMO event revealed one post about IPv4 and IPv6. This indicates to me that I should probably be upgrading the firmware and configuring its use for IPv6 compatibility.If I upgrade to FW 2.30NA, how should I configure the IPv6, i.e., which parameters should I use?
View 6 Replies
View Related
Jun 23, 2012
I am having a problem which I can't seem to find a way around. I have a DIR-615 E3 that I'm unable to get IPv6 to work properly on.I'm connecting to IPv6 over PPPoE, and I'm unable to change the 'IPv6 LAN Address' to an IP my provider has given me. They've provided a native address in the 2607:: range, however on the router it's stuck at a 6to4 IP which is NOT what they've given me (2002:CEF8:8B79:: IP).
I'm thinking of buying a new router that either has better IPv6 support, or one that supports OpenWRT and working my way through that.
View 1 Replies
View Related
Jul 19, 2012
We have some technical issue with IPv6 router configuration[DLINK 655] when we try to connect it with ISP provided static IPv6 connection.
[Code]...
View 9 Replies
View Related
Oct 14, 2011
I have a d link dir 615 "ipv6 ready". My internet provider give tome a native ipv6 /48. I configure the router with my ipv6 /48 address the internal propagation of the address is good.
On the status ipv6 page all seems OK marked "connected" but I can't have an ipv6real connection and my provider say to me that i am not connected.
Is there a known problem of connection between an public /48 and the internal /64 and if so could it be corrected.
View 12 Replies
View Related
Jun 4, 2012
disable NAT on my Dir-655.I have another Firewall which NAT all my requiests and I do not want that my Dir-655 do this work.
View 14 Replies
View Related
Mar 24, 2013
Recently I wanted to setup IPv6 for my home network. I signed up for tunnelbroker.net service and was provided with IPs. Then I configured the IP address in my DIR-615. But It's not working..
Screenshot of IPv6 config (router) : Screenshot of my Win 8 network Config : I also tested at [URL] but failed...
View 3 Replies
View Related
May 16, 2013
I currently have ipV4 as the setting on my DIR-825. Other posts seem to want ipV6 which is more secure but is not possible with a DIR-825 Rev A1. I have two routers, a primary router (DIR-825 Rev B1) capable of ipV6 and a secondary router (DIR-825 Rev A1). If I implement ipV6 on the Rev B1 router but keep ipV4 on the secondary router, will this improve the security, or will it just mess things up so nothing works?Certain devices (cell phones and most Tablets) don't deal with ipV6 very well at all. The ones I have tested flat don't connect to the wireless network if the router is set at ipV6. Is ipV4 adequate for a Home/Small Business Network when trying to implement Remote Access and VPN?
View 2 Replies
View Related
Mar 30, 2012
I am having trouble with a DAP-1522 in AP mode dropping IPv6 packets. It is running in AP mode to supply connectivity to a number of laptops + a 2nd DAP-1522 in bridge mode. The laptops are able to get IPv6 router advertisements from the same wired network the DAP-1522 is plugged into, but they get nothing when connection to the wireless. Tcpdump sees no router adv's coming over the wireless interfaces when sniffing.This appears to be something others have hit as well url...
View 3 Replies
View Related
Jun 9, 2011
I have a Dlink DIR-825 B1 with firmware 2.05NA. I recently reset it to factory defaults to make sure I didn't misconfigure something.
I have been struggling to get a IPv6 in IPv4 tunnel working with tunnelbroker.net. I think the issue is a problem with the router itself and i'm not sure how to get it fixed.
All of my machines were getting IPv6 addresses (both windows, mac, linux) but none of them seemed to work. All I was able to do was ping the gateway itself using the local lan address. In each case they were missing a default IPv6 route. If I added a default route then it would work.
I started looking at the packets using a network sniffer and the Router Advertisements all had a Router lifetime value of "0" which is RFC4816 speak for "don't use this router as the default router". So Windows/Linux is exactly right by not setting a default route.
The strange thing was that when I reboot the router I would briefly get a router advertisement with a lifetime of 1800s, the corrert prefix and dns server but then another router advertisement would come along 5 seconds later with a router advertisement of 0.
I have TCP' Other observations
... using 6to4 I would get working IPv6 address. The difference again seemed to be the Router Lifetime. But I want to use a permanent tunnel. I have found 6to4 unreliable.
... the router never responds to router solicitations. It only sends a router advertisement when it wants to.
... the router never responds to DHCPv6 when that is configured.
View 1 Replies
View Related
Mar 25, 2013
How do I disable both WPA, and WPS on the DIR-815 router, so I would be able to use WPA2 only which is the strongest encryption?
View 14 Replies
View Related
Mar 13, 2013
I have a n Ipad 4 with bad Wifi when connecting through a DL835, Firmware Version: 1.02. Other devices are fine and apparently i should try disabling WMM. I can see WMM but it's grayed out and i cannot disable.
View 1 Replies
View Related
Apr 20, 2013
Region : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 121225 Rel.37950n
ISP : Comcast
just upgrade to the latest firmware and was checking to see if I had IPv6 going with the router but it seems like it's not enabled?I went into my local area network properties and it shows checked and obtain automatically.went into the router ipv6 support tab and it shows:
IPv6 Status
WAN
Connection Type:
DHCPv6
IPv6 Address:
[code].....
View 1 Replies
View Related
Apr 3, 2011
My boss asked me to disable access to Facebook since most of the employees are just spending time with it instead of working. I have done this by means of Website Filter and it works. However, some people have found a way by installing Digsby on their machine, tho they're not really able to go the facebook page, they are actually able to chat with their facebook buddies. Is there a way for me to block access to the facebook API or anything Facebook related?
View 6 Replies
View Related
Oct 18, 2011
I have a DIR-651 Router (I could not find one for the 651) and I would like to use it as a router only.Is there a way to disable the wireless functionality.
View 2 Replies
View Related
May 3, 2012
I want know if it's possible with a script enable disable wifi, without every time login to router.
View 1 Replies
View Related
May 14, 2011
Is there any way to disable internet access for selected PCs, while still allowing them to access the LAN?
View 2 Replies
View Related
Apr 16, 2013
Region : Others
Model : TL-WR843ND
Hardware Version : Not Clear
Firmware Version :
ISP :
I buy TL-WR843ND router to provide a better signal upstairs. Router is in wisp mode with statick ip. Everyting work good. I have routed home network with mikrotik. And everyting was setup with priority on mikrotik for each user separately. With this router every user connercted on it was hidden behind TL-WR843ND. How to disable NAT on TL-WR843ND to use routed network?
View 5 Replies
View Related
Dec 15, 2012
Region : NewZealand
Model : TD-W8960N
Hardware Version : V3
Firmware Version : 1.4.0 Build 111130 Rel.56405n
ISP :
According to the manual, when I go to edit my WAN connection, I should be able to enable/disable the SPI firewall. However, on my firmware I get no such option. My SPI firewall is always enabled.
I would like to be able to completely disable it when I'm testing so that I can ensure the firewall is not interfering with my tests.
View 1 Replies
View Related
Feb 28, 2013
Region : UnitedStates
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version : 3.13.12 Build 120405 Rel.33996n
ISP : Comcast
Why am I unable to "disable" the UPnP in my TP-LINK TL-WR1043ND wireless router? When I click on the "disable" button nothing changes. I click on the "disable" button that then click of "refresh" and it still doesn't change to disabled.
View 3 Replies
View Related
Apr 3, 2013
Region : UnitedStatesModel : TL-WDR4300Hardware Version : V1Firmware Version : ISP :Is there a way to disable the router DLNA media server? Media service is stopped in the config page. I've never used it so ideally it wouldn't appear in a PS3, Smart TV, etc.
View 1 Replies
View Related
Nov 21, 2012
Region : NewZealand
Model : TD-W8960N
Hardware Version : V3
Firmware Version : 1.4.0 Build 111130 Rel.56405n
ISP :
Just installed my new 8960 and it's working fine. However, I'd like to disable admin access from wireless, and only have that available via the LAN. I can't find anything that looks like it'll do that in any of the setup pages, is it possible? All previous wireless routers I've had have been able to do this.
View 4 Replies
View Related
May 29, 2013
After reboot WLC , the switch port was err-disable , the cause is link flap after we reboot 3 times , the switch port link flap err-disable every time? We don't know why the WLC rebboot will cause it , it just normal action on device the WLC version is 7.4.100.0 link switch with access port , no port channel , no portfast.
View 11 Replies
View Related
Oct 25, 2011
how to enable ipv6 on pc?
View 1 Replies
View Related
