My boss asked me to disable access to Facebook since most of the employees are just spending time with it instead of working. I have done this by means of Website Filter and it works. However, some people have found a way by installing Digsby on their machine, tho they're not really able to go the facebook page, they are actually able to chat with their facebook buddies. Is there a way for me to block access to the facebook API or anything Facebook related?
Region : NewZealand Model : TD-W8960N Hardware Version : V3 Firmware Version : 1.4.0 Build 111130 Rel.56405n ISP :
Just installed my new 8960 and it's working fine. However, I'd like to disable admin access from wireless, and only have that available via the LAN. I can't find anything that looks like it'll do that in any of the setup pages, is it possible? All previous wireless routers I've had have been able to do this.
So i can't access my Facebook page i log on it fine at school & I used google chrome & safari, & internet explorer and every time i log on it says SSL Error & it also says that "you attempted to reach www.facebook.com, but instead you actually reached a server identifying itself as *.vkontakte.ru this may be cause by a misconfiguration on the server", idk what to do. I did everything, cleaned it for viruses and checked the proxy & everything.
i cant get access to facebook from my server i download another browser that did not work, it keep saying that, well a matter of fact it don't load at all, it very slow when it click to start the page,. i did have facebook access about a week ago but i dont know hat happen why i cant access it here and said the client on the server can access facebook but i cant how is that possible?
I cannot access the desktop version of Facebook. Whenever I try it says that the connection has timed out. I can get on all other sites without any problems. I tried to figure out what was wrong. I went on Cmd and pinged facebook and it said the connection was timed out. So I did tracert and after the 8th hop it said connection timed out. I tried on 2 computers and a tablet and the same thing happens. When I turn off my router and computer and turn both back on then I can get on the site once with no problems.
I've been having this problem for about a month. When I first start my computer, all three sites load fine. After a few hours, the error page comes up stating that Google Chrome (my primary browser) can't load the page. A few weeks ago if I switched over to Internet Explorer, the sites would still be able to load. Now the sites don't load after these few hours in any of my browsers. I've done malware, spyware and antivirus scans and threats did come up, but now there are none and this keeps happening. I also did a DNS flush and it didn't work. This is my log, but my host files are being blocked[CODE]
I have fiber optic net, going into a TP Link 1043 ND router out in my garage.All of the 4 lan ports go into one of the rooms in the house. I also have two more routers of the same kind, one downstairs and one upstairs.They are configured in a way, that DHCP server is only turned on, on the one in the garage, the other two act as switches.My problem is that 50 % of the time I can't acces facebook, and some other random sites.The interesting bit is that when I chat with someone on FB, I can see what they write, but my message doesn't go through.The way it goes, is that I can browse on facebook for like 5 minutes, after that its unavailable for another 5 minutes.I can still access the site from my smartphone, but only if its not connected to the wifi network, meaning the problem is somewhere within my setup.I've already tried turning the router firewall off, but that doesn't make any difference.
It works on the mobile site at times maybe twice a day but only able to access for 10 minutes maximum. I tried the command prompt and ping facebookm and noticed that I didnt recieve files back and it was just timing out is that whats causing it?
I have been trying to resolve this issue with only allow facebook access throug the content filter between 12pm and 1 pm. However The settings never seem to take. Is this a bug in the system? If I start the filtering from 1300 to 1200 that should allow facebook to be accessible only on lunch.
This problem started happening a few days ago. Whenever I try to access [URL] on my computer that's not physically connected to the router and modem, I keep getting a 403 error:
You don't have permission to access / on this server.
Additionally, a 404 Not Found error was encountered while trying to use an ErrorDocument to handle the request.
Apache/2.2.22 (Unix) mod_ssl/2.2.22 OpenSSL/0.9.8e-fips-rhel5 mod_auth_passthrough/2.1 mod_bwlimited/1.4 FrontPage/5.0.2.2635 Server at www.facebook.com Port 80 --
but I can access touch.facebook.com and m.facebook.com. If I use the computer that is physically connected to the router and modem, I can access Facebook fine. I've tried using CMDPrompt and releasing/renewing IP to no avail. I use the belkin n150 router with updated firmware and the linksys wireless-g pci adapter with v3 drivers. Never had an issue before up until now.
I've been using my WRT310Nv2 Cisco wireless Gigabit N router for 2 weeks now, and sometimes, it's blocking access to Facebook.comI am not aware if it does the same thing with other websites, but my guess is that if I fix this one, I'll fix them all. So here I go, I click on my Facebook icon in my bookmarks and all goes well. Then, a while after, Facebook doesn't respond anymore and I'm send to a page that says "this is probably not the webpage you are looking for!" and it goes on about someone probably trying to hack my Internet and so on. But it's impossible: my network is under a solid WPA/WPA 2 security access. So I try again and click on the FB icon, and it shows me this:
"Invalid URL The requested URL "/", is invalid. Reference #9.c2c28f18.1352263449.304a8c9"
On E4200 Firmware Version: 1.0.03, I managed to successfully set up "Internet Access Policy" (not the "Parental Controls") to set up the times when internet access is disabled for various IPs on my network.
But I could't setup a policy to block facebook.com. What I am doing wrong? See the attached screen shot. I did click the "Edit List" and apply this polity to the IP Address Range 192.168.1.2 to 192.168.1.254.
I have a n Ipad 4 with bad Wifi when connecting through a DL835, Firmware Version: 1.02. Other devices are fine and apparently i should try disabling WMM. I can see WMM but it's grayed out and i cannot disable.
I have a DIR-651 Router (I could not find one for the 651) and I would like to use it as a router only.Is there a way to disable the wireless functionality.
I've had my DIR-615 up for several months, and it's been faultless except for one thing. I have router in front of it and only use the 615 as a switch and AP. My main router provides IPv6 access through a 6to4, using radvd to broadcast to the rest of the network.
Whatever setting I set the 615 to for IPv6, it always sends out a default route. On rare occasion, it'll interfere with the correct route from my main router (whose router preference is set to high, instead of medium). Even in local-only mode, the 615 sends out a default route. It's an E1 with the 5.00NA firmware, which I believe is the latest.
I'd really like to disable the advertisements from the 615 altogether, while keeping L2 IPv6 support on the wireless and all. I picked this router explicitly because many routers don't work with IPv6 over WiFi, but it'd be nice to get it working perfectly. If there aren't any ways to do this, is there a place that I can download the source for the firmware?
Region : Others Model : TL-WR843ND Hardware Version : Not Clear Firmware Version : ISP :
I buy TL-WR843ND router to provide a better signal upstairs. Router is in wisp mode with statick ip. Everyting work good. I have routed home network with mikrotik. And everyting was setup with priority on mikrotik for each user separately. With this router every user connercted on it was hidden behind TL-WR843ND. How to disable NAT on TL-WR843ND to use routed network?
Region : NewZealand Model : TD-W8960N Hardware Version : V3 Firmware Version : 1.4.0 Build 111130 Rel.56405n ISP :
According to the manual, when I go to edit my WAN connection, I should be able to enable/disable the SPI firewall. However, on my firmware I get no such option. My SPI firewall is always enabled.
I would like to be able to completely disable it when I'm testing so that I can ensure the firewall is not interfering with my tests.
I have a MI-FI dongle which i use to connect to the internet (small wireless router) It does not support a wireless printer though. So I figured IU would use the old BT Home hub I had to connect my computer and the printer.
This worked for a few minuites untill the computer decided that the home hub should be dominent and instead of accesing the internet the browser would show the bt cannot conect to the internet page.
Region : UnitedStates Model : TL-WR1043ND Hardware Version : V1 Firmware Version : 3.13.12 Build 120405 Rel.33996n ISP : Comcast
Why am I unable to "disable" the UPnP in my TP-LINK TL-WR1043ND wireless router? When I click on the "disable" button nothing changes. I click on the "disable" button that then click of "refresh" and it still doesn't change to disabled.
Is it possible to disable network access until a reboot under Linux? I am interested in creating a Freedom equivalent for Linux (currently only available on Windows/Mac)
Region : UnitedStatesModel : TL-WDR4300Hardware Version : V1Firmware Version : ISP :Is there a way to disable the router DLNA media server? Media service is stopped in the config page. I've never used it so ideally it wouldn't appear in a PS3, Smart TV, etc.
I recently had my Internet disconnected, and decided to share my iPhone's Internet connection (tether) with my PC. Now, the iPhone connection works, but for some reason my PC prefers to use my original Internet connection thus no connection. The only way I can access the Internet is by going into adapter settings and disabling my router, but I do not want to do this as I have other computers on the network and I often share files.
I have a question about managing the Access Point:
-WLC2504 -AIR-LAP1262N-A-K9
First: I need the access point works by period, example: 08:00AM - 06:00PM after that disable the radio and return work next day at 08:00AM
Second: Also, if the radio no activity for a long period (e.g 60 or 120 minutes), disable the radio interface.It's possible with the WLC? Or maybe need implement one NCS?EnergyWise Technology - but, I only need "shutdown" the radio not the Access Point completely.
I would like to disable NAC policy control from my ACS 4.0.I would like only 802.1x AAA on my switch ports.Also I'd like to assign a different VLAN to different MAB devices by RADIUS user attribute, in order to differentiate vlan for printers, clocks and so on. Any document for ACS 4.0?
I want to disable the guest access connection on E1000 wireless router but this option is not in the firmware menu. So, now I read that I need to use Cisco Connect on the CD to change this feature. When I run the Cisco Connect software, it says it can't configure the router (probably because I already have it configured). Why doesn't the Cisco Connect software simply take me to the settings where I can change the guest access feature? Why does it try to re-configure the router? Whoever designed this at Cisco was probably smokin some medical MJ because it doesn't make any sense that I have to go through so many hoops to do something so simple.
After reboot WLC , the switch port was err-disable , the cause is link flap after we reboot 3 times , the switch port link flap err-disable every time? We don't know why the WLC rebboot will cause it , it just normal action on device the WLC version is 7.4.100.0 link switch with access port , no port channel , no portfast.