Disable The Ipv6 Using The Regedit?
Feb 15, 2011i tried to disable the ipv6 using the regedit and all and i restarted my pc but when i check the local network are connection and properties the ipv6 is still checked.
View 8 Replies
ADVERTISEMENT
D-Link DIR-615 :: Disable IPv6 Stateless Advertisement?
Sep 19, 2010I've had my DIR-615 up for several months, and it's been faultless except for one thing. I have router in front of it and only use the 615 as a switch and AP. My main router provides IPv6 access through a 6to4, using radvd to broadcast to the rest of the network.
Whatever setting I set the 615 to for IPv6, it always sends out a default route. On rare occasion, it'll interfere with the correct route from my main router (whose router preference is set to high, instead of medium). Even in local-only mode, the 615 sends out a default route. It's an E1 with the 5.00NA firmware, which I believe is the latest.
I'd really like to disable the advertisements from the 615 altogether, while keeping L2 IPv6 support on the wireless and all. I picked this router explicitly because many routers don't work with IPv6 over WiFi, but it'd be nice to get it working perfectly. If there aren't any ways to do this, is there a place that I can download the source for the firmware?
Cisco WAN :: How To Disable IPV6 On 6500 Switch
Jun 17, 2012I want to learn that,on cisco switch (2950,3600,6500 series) IpV6 default open? İf It comes open on default,how to disable?
View 19 Replies View RelatedDisable IPv6 Loopback On Windows 7 64Bit?
Feb 24, 2013I have a Windows 7 64 Bit machine, and I cannot find a way to disable the IPv6 Loopback. I looked at the article at How to disable IP version 6 or its specific components in Windows and shows how to set HKEY_LOCAL_MACHINESYSTEMCurrentControlSetServicesTcpip6ParametersDisabledComponents to various values – but none of these seems to disable IPv6 Loopback. I attempted setting this value to 0xffffffff and 0x20 – restarting my computer after each change, and I still do not get this disabled.
I am using another software called Webdriver or Selenium that gives errors when debugging if IPv6 Loopback is not disabled. It seems to attempt to connect to [::1]:7055 and fails. Is there a way to force it to connect to 127.0.0.1.
Linksys Wireless Router :: Disable IPv6 For Parental Controls?
Jan 14, 2013So I've realized that my parental controls were being ignored by the computers, at first I figured my son had found a work around to by-pass. But reading through the forums today, I've found that IPv6 being enabled might be the cause of my issue. So I'm currently sitting at work and connected to my router remotely, but for the life of me, can't see where to disable this option. Using the Smart Wi-Fi interface, closest I can get is "Connectivity, Internet Settings, IPv6 but everything is grayed out and no option to edit this.
View 9 Replies View RelatedDisabling NIC With Regedit?
Aug 27, 2012I have a friend who is in need of a laptop or netbook only for word processing.
The device cannot have any possibility of connecting to the internet, and also cannot have a webcam. I may be able to find one without a webcam, but I think the possibility of finding one without a NIC wouldn't be easy, if at all possible.
I can only think that disabling the network adapter in registry edit will be something she won't be able to undo (she's not majorly tech savvy).
I've not purchased the laptop/netbook yet, but I would like to know if it's possible and/or how to do it before I buy it.
Optimizing Internet Connection With Regedit (EXE File)?
Dec 25, 2012I've been reading about optimizing my internet connection by editing and creating keys in the regedit program. I'm not sure if I've tried everything, which keys I should edit and what I should set the value as.
View 2 Replies View RelatedHow To Enable Ipv6 On Pc
Oct 25, 2011how to enable ipv6 on pc?
View 1 Replies View RelatedHow To Use Remote IPv6 Over Ssh
Jun 15, 2013I have a cheap VPS with 1 IPv4 and 5 IPv6.
I want to use 1 of the unused IPv6 connections on my computer so I can start using IPv6
Cisco :: Why Can't Set An IPv6 Address
May 2, 2012Why can't I set an IPv6 address here (WS-2960-48TC-L latest IOS)
View 7 Replies View RelatedIPv6 - No DNS Query When Using Firefox And IE?
Feb 8, 2011I am setting up a Linux apache and bind server to test the behaviour of Windows XP,Vista, 7 and Mac OS X.I have setup a apache and bind already and they were tested individually. I used Firefox and IE to access the apache page by type in the IPv6 address and the page was showed correctly. And I have tried to query the AAAA record of a local zone "testing.com" in my Bind server using nslookup and the result is good too.However, it is strange that I cannot get it work if I type in the FQDN "http://testing.com" in Firefox and IE. I tried to capture the IPv6 traffic in Wireshark (Attached in this post) and there are no DNS query when I try to access the page. Is there anything that I have to set to get it work properly?(Actually I have tested the same thing on Mac OS X and Vista too but the result is the same)Below is my Windows 7 network setting and some nslookup query:
C:Usersvmware>ipconfig /all
Windows IP Configuration"
Host Name . . . . . . . . . . . . : vmware-PC
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
[code]....
Local Only Ipv6 Connectivity?
Jul 24, 2012My internet is really slow and i keep getting disconnected. the ipv6 box says local only. when i uncheck it it goes to limited my pc is running vista home premium
Windows IP Configuration
Host Name . . . . . . . . . . . . : anthony-PC
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : Yes
WINS Proxy Enabled. . . . . . . . : No
[code]....
when i do netsh int ipv4 reset reset.log AND netsh int ipv6 reset reset.log - the command prompt says Reseting Echo Request,Failed.Access is denied.There's no user specified settings to be reset.
Cisco :: Possible To Connect Ipv6 Over 4
Oct 23, 2011So I've got a IPv6 tunnel with Hurricane Electric and it's currently physically segmented off of my home network. A 1841 terminates the tunnel and if I want to use it I need to plug into a port thats on a VLAN with no SVI and connect outbound to test IPv6 stuff. I'd like to give access to some other users and Im wondering if 6 over 4 tunneling with AnyConnect will work for that. My thought was that they could terminate on my main firewall (5505) and then terminate their VPN session in another vlan which was connected to the IPv6 router. I have this config working right now with IPv4 and I can browse out but Im struggling with the IPv6 support piece. The admin guides from Cisco seem to indicate that I'll need to configure IPv6 addressing on the ASA which makes sense, but doesnt fit my current design.
View 2 Replies View RelatedD-Link DIR-825 :: How To Update For Ipv6
Jun 25, 2012When I check for firmware updates for my DIR-825 I get a return that there are none.How do I update for for ipv6 then?
View 5 Replies View RelatedCisco WAN :: IPv6 ISG On ASR1000
May 5, 2013We use ISG on asr1000 (l3 routed subscriber). Now we are trying to implement ipv6 isg sessions. so.. for ipv4 sessions we have
radius-server attribute 8 include-in-access-req
radius-server attribute 32 include-in-access-req but for ipv6 there is no such attribute#radius-server attribute ?
11 Filter-Id attribute configuration
188 Num-In-Multilink attribute configuration
218 Address-Pool attribute
25 Class attribute
30 DNIS attribute
31 Calling Station ID
32 NAS-Identifier attribute
4 NAS IP address attribute
44 Acct-Session-Id attribute
55 Event-Timestamp attribute
6 Service-Type attribute
60 CHAP-Challenge attribute
61 NAS-Port-Type attribute configuration
66 Tunnel-Client-Endpoint attribute
67 Tunnel-Server-Endpoint attribute
69 Tunnel-Password attribute
77 Connect-Info attribute
8 Framed IP address attribute
95 NAS IPv6 address attribute
list List of Attribute Types
nas-port NAS-Port attribute configuration
nas-port-id Nas-Port-Id attribute configuration
what is best practice for authorize ipv6 l3 subscribers ?
Cisco WAN :: Can't Get IPv6 To Work On 877
Feb 23, 2010I can't get IPv6 to work on my Cisco 877:Do I need to do something to enable it? I have a /56 from our ISP that I would need to configure.
View 12 Replies View RelatedRouters / Switches :: What Is Protocol 41 With Ipv6
Aug 26, 2011Protocol 41 with ipv6
View 1 Replies View RelatedWhich Is Ipv6 Driver In Windows 7 Ultimate
Aug 18, 2011when i tried to install ipv6 using dail up connection ,right click on properties scrolling networking tab checked internet protocol version 6(tcp/ipv6) and click install then select network features type is protocol selected . add - i have to choose from have disk- A: - browse- local file - system 32 here i donot know which .inf should i select .
View 1 Replies View RelatedCisco :: IPv6 EUI-64 On Serial Interfaces
Sep 9, 2012I understand that IPv6 uses the MAC address of a LAN interface to make up the EUI-64 of a serial interface since serial interfaces don't have MACs. What happens when there is no LAN interface available? What if the switch has only serial interface cards?
View 2 Replies View RelatedPing IPV6 General Failure
Jan 18, 2012When ping ipv4 is succeeded.
C:Documents and SettingsLW>ping 10.1.1.1Pinging 10.1.1.1 with 32 bytes of data:Reply from 10.1.1.1: bytes=32 time=2ms TTL=64
Reply from 10.1.1.1: bytes=32 time=1ms TTL=64
Reply from 10.1.1.1: bytes=32 time=1ms TTL=64
Reply from 10.1.1.1: bytes=32 time=1ms TTL=64Ping statistics for 10.1.1.1:
Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
[code].....
DNS Not Working IPV4 IPV6 Not Connected?
Jan 11, 2013has quite frankly gotten me absolutely annoyed . I've tried just about everything, from using the netsh commands to changing the dns to 8.8.8.8 or that other one or the other. Nothing is working, I unplugged the router, problem persists, I disabled IPV6 problem persists, I restore, problem persists. The only clue I have is my router, and mysteriously, there are TWO of my computer on it. It might be nothing but most certainly has caught my attention. Also, it gives me this info about my media being disconnected
View 14 Replies View RelatedRouters / Switches :: How To Format IPv6
Feb 6, 2011want to know how to format IPv6
View 1 Replies View RelatedD-Link DIR-825 :: IPv6 Not Working When Using It As Switch And AP?
May 10, 2010I am using my DIR-825 as a switch and AP. I have turned off DHCP and plugged the internet into the lan-1 port. This works perfectly for IPv4, but I cannot get IPv6 to work. On the outside there is native IPv6 running radvd. How should I configure IPv6 on my DIR-825?
View 2 Replies View RelatedD-Link DIR-825 :: IPv6 Firewall Implementation
Apr 17, 2012Unfortunately I didn't discover any configuration switches concerning an IPv6 firewall! So the important question is: Is there any firewall implemented at all? And if so, does it confirm to RFC6092.
View 14 Replies View RelatedD-Link DIR-615 :: IPv6 Static Routes
May 5, 2011Will there be a way sometime in the future to add static IPv6 routes? I have a routed /64 and a routed /48 from a tunnel broker that terminates on my DIR-815, and I want to hang the /48 off of another router that I have attached to my LAN interface(goes to my home lab setup that I use for my job). I could just move the tunnel endpoint to the other router, but I like having IPv6 access for all my other PCs on the LAN segment.
View 1 Replies View RelatedD-Link DIR-655 :: FW 2.30NA - Way To Configure IPv6?
May 17, 2012I'm still using 2.00NA.It seems that whenever I connect to a particular www3 webpage, my modem and router end up rebooting shortly thereafter. This has happened a few times. The modem's log shows in this order1. No Ranging Response received ,2. Unicast Ranging Received Abort Respone ,3. MIMO Event.I've tried to figure this out. My search on the MIMO event revealed one post about IPv4 and IPv6. This indicates to me that I should probably be upgrading the firmware and configuring its use for IPv6 compatibility.If I upgrade to FW 2.30NA, how should I configure the IPv6, i.e., which parameters should I use?
View 6 Replies View RelatedCisco :: IPv6 Netflow Support On PI1.2?
Jan 9, 2013i just came to know Assurance feature license doesn't come for free when upgrading from LMS4.2 or NCS1.1. It has to be purchased. Before buying this license, i would like to know if IPv6 netflow is supported.
View 0 Replies View RelatedCisco VPN :: IPv6 Support On ASA 8.4 IPSEC
May 7, 2011I need to implement IPv6 for ASA VPN. According to the ASA_8.4_cli_cfg.pdf , IPv6 is not supported on ASA IPSEC vpn and remote client vpn. I do not have a ASA 8.4, any way to verify on ASA8.4 whether the crypto command support ipv6 address ? If the crypto command do support ipv6 address then probably there is chance it will work.what i mean is eg. crypto map xxx set peer <ipv6 address| ipv4 addres> able to set ipv6 address.
View 4 Replies View RelatedCisco :: Does LMS V3.2 Support IPV6 In All Modules
May 1, 2013Does cisco LMS v3.2 Support IPV6 in all modules ? We will be migrating from V4 to V6 in some time from now
View 1 Replies View RelatedCisco VPN :: IPSec VPN IPv6 Between ASA 5550 And 881?
Sep 6, 2011Currently on internship in a multi-site company, I am studying the IPv6 transition.I have to perform several tests and i was wondering if is it was possible to make a Site-to-Site IPSec VPN with IPv6 between a Cisco Asa 5550 and a Cisco 881 router.
View 17 Replies View RelatedCisco WAN :: IPv6 Support On ASR 9000
Jun 10, 2013According to the url below, i could find that there is a separate module required for asr 9k, is it so; doesnt it sufficient to have the 4.3.0 Ios-xr version for the cgnat supoort features of nat 44, nat64, ds-lite.. like things?URL
View 1 Replies View RelatedCisco :: WLC 5508 And IPv6 Not Joining With Each Other
Apr 3, 2013recently migrated APs from a 4400 to 5508 which had the 7.4 code and encountered an issue that I haven't see before, in short the APs would never join the 5508 even when the selction rules said it should.The AP would get a discovery response from both controllers and even though the 4400 had 98 APs attached and the 5508 just 1 and a factory reset was made on the AP, it would always join the 4400.
A packet capture showed that the first CAPWAP address from the 5508 was always an IPv6 whilst the 4400 always sent IPv4 CAPWAP control adressess, disabling the global IPv6 option on the 5508 ensured that the the first CAPWAP control address was now an IPv4 and the AP then happily joined the controller, IPv6 addresses were still showing up in the discovery responses but since it was no longer the first one in the packet the AP didn't mind.
Cisco :: Can't Generate Pre-shared Key For Ipv6 Tunnel
Jan 18, 2013I'm playing with ipv6 and trying to get a tunnel between two sites working (basically following this example url...
View 6 Replies View Related