Cisco Wireless :: OEAP-600 AP Backup Connectivity To WLC
May 20, 2013
Here's the list of equipments:
Pool of oeap 600 aps
1x 2504WLC as OEAP WLC (@DMZ)
1x ASA 5515
Scenario:
My OEAP WLC located at ASA - DMZ is NATted to a public ip (primary internet ISP), then my pool of OEAP-600 were configured to communicate with this OEAP WLC.
My question is:
I want to automate the failover of OEAP-600 (I don't know if this is possible) to the secondary internet ISP whenever the primary internet ISP fails. The secondary ISP is terminated on the same ASA 5515-X doing PBR and IP SLA stuff.
I know that OEAP 600 can only be pointed to one WLC ip address I know that the WLC can only be NATted to one public IP address.
What would be the best solution to perform the OEAP backup connectivity? Or just buy another set of WLC/ASA then just manually configure the OEAP-600 APs to point to the secondary ISP.
View 6 Replies
ADVERTISEMENT
Jun 13, 2011
I have configured Cisco 2811 and 3825 routers to connect the main and remote sites as per the attached topology. At the main site, the Cisco 3825 router is equipped with SFP ports (HWIC-1GE-SFP with GLC-LH-SM=) for fiber optic connectivity and also has a HWIC-1CE1T1-PRI installed The Cisco 2811 routers at the remote sites are each equipped with a WIC-1SHDSL-V3 module for SHDSL connectivity and with a WIC-1B-S/T-V3 for backup ISDN connectitivty.
In normal time the routers are using the SHDSL to Fiber optic connectitivty for communication. This has already been configured and is working. Now, there is a need to implement a backup connection between these sites such that in case the SHDSL or fiber optic connectivity fails, the routers should automatically dial up the backup ISDN connectivity so as to ensure business continuity.
View 3 Replies
View Related
Feb 18, 2013
We have cisco 5508 office extend in dmz running code 7.3.112. 1132 AP seems to register and authenticate fine but OEAP 600 series dont seem to authenticate. they seem to join the controller and download the SSID but just wont authenticate ? not even registering on the AAA server
View 9 Replies
View Related
Aug 20, 2012
I have found that there are only few configuration to the Cisco Aironet 600 OEAP. The settings are just for basic configuration for a wireless network when it is in autonomous mode.
A need for a Wireless LAN Controller to perform advance settings.
Also, there are no firmware available in Cisco. No upgrade/downgrade firmware avalaible for download.
View 4 Replies
View Related
Sep 23, 2012
I have a customer looking to deploy OEAP & wants to know if it possible to disable the local ports 1-3? Reason being, they don't want the home user connecting devices & causing more support tickets to troubleshoot an Xbox or Google TV just b/c it's connected to a company provide AP/Switch. I have read all the docs & it makes no mention of this.... I can see in 7.2 the ability to disable the local SSID but no mention of the ability to shutdown ports 1-3..Also see support in 7.2 for Dual RLAN... but that still leaves 2 local ports.
View 5 Replies
View Related
Oct 1, 2011
I have some trouble with the setup of an oeap 600 ap. The ap has joined the controller as it should and the remote-lan connection to my corporate network works well, but i can't connect to the corporate wlan.
When i check the event log on the ap it says:
"
*Oct 02 07:36:56.662: (Re)Assoc-Req from 00:1a:73:d2:82:8c forwarded to WLC, wired: no
*Oct 02 07:36:56.665: received assoc-rsp for wireless client, status=0011
*Oct 02 07:37:11.712: DisAssoc-Req/DeAUTH from 00:1a:73:d2:82:8c forwarded to WLC, wired: no
*Oct 02 07:37:11.713: WTP Event: Delete Mobile sent to wlc00:1a:73:d2:82:8c"
and a debug on the controller gives me:
apfMsConnTask_6: Oct 02 08:52:05.034: 00:1a:73:d2:82:7f Adding mobile
on LWAPP AP ec:c8:82:c2:3a:20(0)
*apfMsConnTask_6: Oct 02 08:52:05.034: 00:1a:73:d2:82:7f Association received from mobile on AP ec:c8:82:c2:3a:20
*apfMsConnTask_6: Oct 02 08:52:05.034: 00:1a:73:d2:82:7f Sending Assoc Response to station on BSSID ec:c8:82:c2:3a:20 (s
tatus 17) ApVapId 1 Slot 0
[code]....
View 3 Replies
View Related
Apr 17, 2012
Possible to assign reslient WLCs to an OEAP 600?
The web GUI of the OEAP itself only has a single field to enter the address of a single controller.
But, I wonder if once the OEAP is talking to your WLC across the Internet, you can allocate HA settings to the OEAP so that it can fall back to a secondary WLC if your main WLC fails.
This is sort of hinted at in the docs I have read, but I have not been able to find it explicitly stated anywhere.
It would be nice to have 2 DMZ-based WLCs at two different data centres to allow remote users to have a fail-over solution, but I need to be sure that this is supported before implementing.
View 7 Replies
View Related
Mar 7, 2013
I have a TAC case open, but it doesn't seem to be making any progress.I upgraded my 5508 controller from 7.2.111.3 up to 7.4.100.0..Most of my APs are fine. 3500s, 1100s etc.except for 602i APs. The APs associate, they update software etc, but they won't broadcast the WLAN.An interesting thing, on the 602 AP, in the log, I see this:*Mar 06 15:08:12.667: SSID remote, WLAN Profile Name: RemoteOEAP, added to the slot[0], disabled..So the AP is definately talking to the WLC and being pushed the correct WLAN profile.On the controller, the AP shows the the Admin status of the radios is showing DOWN, but the Admin status on the AP itself shows UP
I've done a factory reset on the APs to no avail. I have a 2504 WLC as well that i'm in the process of implementing in a DMZ specificially for these APs, and for testing purposes, I associated the 602 Ap to that WLC as well. This one is running 7.4.100.0 too, same results. It would appear to be a problem with this version of software?
View 6 Replies
View Related
Sep 12, 2011
Only fifteen users are allowed to connect on the WLAN Controller WLANs provided on the 600 series at any one time. A sixteenth user cannot authenticate until one of the first clients de-authenticates or a timeout occurred on the controller. Note: This number is cumulative across the controller WLANs on the 600 series. For example, if two controller WLANs are configured and there are fifteen users on one of the WLANs, no users will be able to join the other WLAN on the 600 series at that time. This limit does not apply to the local private WLANs that the end user configures on the 600 series designed for personal use and clients connected on these private WLANs or on the wired ports do not affect these limits. This is from the Configuration Guide for teh 600 series Office Extend AP. Is this count per AP or total per WLC? If I have 10 APs deployed to our remote users, can each AP support two simultaneous users? Would I need to use separate WLANs for each OEAP?
View 8 Replies
View Related
Mar 17, 2012
I've got a strange problem here. In the office, my OEAP 600 can join WLC if there is no MAC authentication. When i enable MAC authentication at WLC, AP will fail to register. However, I try it at home and it works with both MAC authentication enable or disable. I suspect it is because of firewall in my office, but there shouldn't have any different in discovery and joining procedure for AP with MAC authentication enable or disable.
View 18 Replies
View Related
Jun 17, 2012
Flex 7500
Software Version: 7.2.103.0
I have a Flex 7500 with 200 1142AP's working fine in remote office and local setup. We have since purchased 3 OEAP 602's and looking to distribute to teleworkers.
I have configured the OEAP to point to the NAT'd IP of the WLC, the OEAP does connect and is listed briefly in the WLC wireless listing but I am not able to make any configuration changes, it will then dissassociate and try the join process all over again. I have attached below the OEAP 600 event log. I see that the WLC does not support data DTLS encryption and looking to make this work.
I have tried to install the DTLS license file from the Cisco website, but says license failed to install, with no other errors.
*Jun 18 15:18:43.938: Build version 7.0.112.72 (compiled Feb 3 2012 at 01:56:39, [L]).
*Jun 18 15:18:47.859: CAPWAP State: Init.
*Jun 18 15:18:47.860: CAPWAP State: Discovery.
[Code]....
View 2 Replies
View Related
May 21, 2012
I have established dual-rlans on different segments.I have a 2960g switch. I created vl2 (management) and vl3 (data).I connected rlan1 (port4) to vl2 and rlan2 (port3) to vl3.My laptop receives a dhcp address on vl3 and the switch (in dhcp mode) receives it's proper address on vl2.Unfortunately a MAC is assigned to each vl and to the management interface. Thats 3 out of the 2 sets of 4.
So a managed switch is NOT the desired device to have on the back side of an OEAP600.In any case doing a show mac address-table revealed that all the vl2 MAC addresses were duplicated on vl3.To the tune of 216 addresses. 108 in each vlan. Which is a close match to the current host counts for each segment 98 + 18.Obviously this application is not what was envisioned by the OEAP team during work-up.The goal of 4 host devices on the rlan is proving difficult to achieve.The client wants 2 pc's and 2 digi-port servers.
View 1 Replies
View Related
Dec 9, 2012
Does the AP is able to configure 2 public ip address of the DMZ-WLCs?
like ip 1.1.1.1 in my US data center, whereas a second ip 2.2.2.2 in my EU data center?
View 5 Replies
View Related
Mar 15, 2012
I have two 5508 and a few hundred 1142 in our internal net. Now I bought some OEAP 600 to do tests in some small branch offices, but I would like to enable AP policies with MAC filtering to block that anyone else can connect an OEAP through our firewall. If I enable 'Accept Self Signed Certificates (SSC)' and 'Authorize MIC APs against auth-list or AAA' as suggested in Cisco document 'Aironet 600 Series OfficeExtend Access Point Configuration Guide', will that effect only my OEAP 600 or will I have to also include the MAc addresses of my internal 1142?
View 2 Replies
View Related
Feb 18, 2011
want to connect three networks with each other via two media one ethernet/fiber optic and other through wireless as backup link.how can i connect these three networks so that if my ethernet/ fiber optic connection fails than computer on networks can still communcate via wireless link (i mean if ethernet/fiber optic fails then wireless link should automatically be established/
View 1 Replies
View Related
Jan 29, 2013
Currently we have 20 remote sites, each with 2-5 AP's each. They all connect back to our Main Data Site in the US and register on a single WLC5508.
We do not have a backup WLC, but are looking to purchase one. What I would like to know is, are there any problems with the secondary WLC being installed in our Main Data Site in Europe? These two main sites are connected via a 10M MPLS WAN.
So all the remote sites could still connect to the WLC in the US, but in the event of a WLC failure in the US, they would need to fail over to the site in Europe
View 5 Replies
View Related
Feb 5, 2013
how to backup a Cisco Wireless Access Point Controller 5508.
View 2 Replies
View Related
Jun 12, 2012
My customer has a 4402-25-K9 and need a backup (failover) controller to avoid data transmision break when primary controller goes down.4402 are end of sale so I have a question can I use 5508 to get Controller Failover Protection with 4402 ?
View 3 Replies
View Related
Nov 6, 2011
In my WCS v7.0.172.0, I recently configured the Controller Configuration Backup task. Backups seem to be working fine for the past few days. How do I tell it how far back I want to keep logs, or how many log files to keep before deleting the older ones? Seems like it will just keep on saving the config backups with a date stamp until the TFTP server runs out of disk space.
View 3 Replies
View Related
Oct 23, 2012
I just turned on 2 Wirelless LAN Controllers 5508 and I am getting this message on both of them:
Loading primary image (Image not found)
** Unable to read "linux.pri.img" from ide 0:2 **
Loading backup image (Image not found)
** Unable to read "linux.bak.img" from ide 0:2 **
And it is taking me to the BootMenu. I selected option 4 to Clear Configuration and the controller seems to restart the system but I still get the same error. I checked the LEDs status and Sys is Amber and Alarm is OFF which according to the documentation is a System Crash.
View 1 Replies
View Related
Jun 20, 2012
I have a facility, where all the access points almost 250 of them are connected to two WisM's (One in each core switch ) . They are running in 6.0.199 firmware . These two WisM's are managed by WCS , which is running 6.0.188.
As i need to add more access points and to make fully redundant , 5500 controller was ordered and it has with firmware 7.0 installed. Couple of queries related with it .
1. Can 5500 be added in the WLC group, so that existing Access Points can be configured to use primary controller as 5500 and secondary / tertiary controller as WISM ?
2. Will 5500 be able to be detected by WCS , as the version of 5500 is 7.0 and WCS version is 6.0.188 ?
3. As WCS was already deployed and live, is it possible to upgrade, if the client has support contract like SUSA ?
View 4 Replies
View Related
Oct 10, 2012
we have a AP cisco AIR-AP1131G-E-K9 Version 12.4(10b)JA, and we would like to do automatic backup of CLI configuration to one server, and we dont know how to do.
For example: On router and switch we use this kind of configuration to do automatic backup: [code]
View 1 Replies
View Related
Sep 8, 2012
Since WLC5508 MGMT interface is configured a AP-Mgr at the same time, can I set a Backup Port to WLC5508 MGMT interface? Refer to WLC configuration Guide:
In the Backup Port text box, enter the number of the backup port assigned to the management interface. If the primary port for the management interface fails, the interface automatically moves to the backup port.
Note Do not define a backup port for an AP-manager interface. Port redundancy is not supported for AP-manager interfaces. If the AP-manager interface fails, all of the access points connected to the controller through that interface are evenly distributed among the other configured AP-manager interfaces
if I need to configure the backup port for MGMT interface, i need to remove the AP-manager on MGMT interface and create a network dynamic interface for AP-Manager ?
View 2 Replies
View Related
Aug 4, 2011
I am a day trader using Microsoft 7.I need to combine cable (comcast) and a wireless connection (AT&T) as backup into one access point.
View 1 Replies
View Related
Jun 22, 2012
I have 5500 controller with firmware 7.0 installed from the factory. Due to some reasons, I understood that other existing wireless infrastructure runs on firmware 6.0, and hance i need to downgrade the 5500 series to 6.0 . During the bootup, i could see there is another image called backup recovery image, which is running on version 6.0. How can i reboot controller to use the older image , which is from backup recovery image. I couldnt find it in the configuration guide.
View 4 Replies
View Related
Nov 4, 2012
I need to take the backup of configuration file for WLAN Controller 4420, I tried all the possibilities given in the documentation but the backup fails, I have main confusion with the file name to be backedup, i am not able to findout the configuration filename any where even when i use CLI?
View 1 Replies
View Related
Jul 7, 2012
use PAGP as backup for wireless link with another wireless link.
__WiFi________
PC-------Switch 1 Switch2---------- PC
__WiFi________
We are using 2960 series and from this reason we cant use L3 PAGP I dont know how is PAGP working. If it is checkung port status (UP/Down) or there are some specific L2 packet between etherchannel ports in group?
View 5 Replies
View Related
Aug 9, 2012
I have a E1550 with a corrupt config that is acting very wonky lately (shows wrong info in some of the settings and doesn't always save changes). Since it may be the config that is at issue, I don't want to do a backup/resote, rather I plan to do a full factory reset and manully type everything back in.What would be nice is, creating a text based, human readable printout of the config for reference so that I don't have to manually type it all twice (once to save it, once for reentry). PS3 ports, MAC filters, etc. have several entries, and they way the pages are designed it doesn't allow for easy, whole entry, cut and paste.
View 5 Replies
View Related
Jan 10, 2012
I have a 1.5 TB USB hard drive attached to me E4200. Configuring it so that multiple computers have access and can read and write their files is quite simple. I've followed the instructions and had no difficulty.
My problem is this, after about a week's time has passed any file that has been on the hard drive for more than a week become undeletable. Any attempt to modify it or remove it pops up a message saying I need permission from a specific user (always the user that I am currently logged in as!) to perform the operation on the file.
When this starts to happen, the device is, otherwise, perfectly functional. I will still be able to create new files and delete any newly created files from the drive without difficulty even when those files are in the same directory as the files that the device will no longer let me edit. Examination of the file properties dialog shows that the files that the device refuses to allow me to delete are identical in every way to any new file that I create. Yet newly created files are removable but these older files ... are not.
I'm quickly coming to the conclusion that the HDD mounting feature of the device just doesn't actually work as advertised.
FWIW: all my computers are using Windows 7 with the latest build. I do access the device from these computers wirelessly.
View 9 Replies
View Related
Feb 15, 2013
Region : United Kingdom
Model : TL-WR940N
Hardware Version : Not Clear
Firmware Version :
ISP : BT
I've been having some issues with my BT Broadband for a while, so decided to switch to a new router, a TP TD-W8960N, however setting up QOS isn't as easy as I had anticipated (I'm fairly new to this!).
My main issue is that we have a fairly limited broadband connection, but I need to backup work using backblaze. This is a pain because as soon as it starts to backup it eats what bandwidth we have. What I want to know is can I just limit the range of ip-addresses which they use for their backup?Is there a simpler auto-QOS approach I could use? The router is currently running the latest firmware that isn't in beta. Also - do these routers auto-update firmware?
View 2 Replies
View Related
Jul 6, 2011
why Windows Backup in Windows 7 pro 64 would not backup over the network to a drive I have connected to the 4200s USB port? Everytime I run it I get a Access Denied error at the end, even though data has been transfered. After about 5 hours of searching both here and Microsoft's website, I just get lots of people with the same issue that hasnt been resolved anywhere consistantly.
View 1 Replies
View Related
Mar 7, 2012
I have a WRT54GL v1.1 that has firmware version 4.30.14 build 5 installed(according to the device). The latest version listed on your website is 4.30.13. What does this mean? How do I get a backup of my current version?The device seems to be working fine and the manual I downloaded seems to cover it. I'm on a Mac so I have to set it up manually.
View 1 Replies
View Related
Dec 21, 2011
Since lion is there for a while, it is still not possible to make a time machine backup on an USB hdd that's connected to the router. is Cisco coming with an firmware update?
View 9 Replies
View Related
