I have a WRT54GL v1.1 that has firmware version 4.30.14 build 5 installed(according to the device). The latest version listed on your website is 4.30.13. What does this mean? How do I get a backup of my current version?The device seems to be working fine and the manual I downloaded seems to cover it. I'm on a Mac so I have to set it up manually.
View 1 RepliesIt appears that there is no firmware I can download for my WRT54GL Version 1.1. While it may never have been updated from what the router came with from the factory, it would still be useful to have it available. In my case, I would like to revert the router from the DD-WRT firmware to factory specs.
View 3 Replies View RelatedI have what I believe is an original (V1) version of the BEFSR41 gateway/router. The label underneath the device only shows the model number with no version information. Current firmware version on the device is 1.46.02, dated Aug 03 2004.
Can I confirm (1) that I indeed this router is at hardware version 1? If that is the case it appears from your web site that version 1.46.02 is in fact the current and only firmware version for the device and that there are no firmware version upgrades available.
The DHCP software current does not have IP address reservation, which I am interested in adding if possible via firmware upgrade. If not then I have to consider whether I want this feature bad enough to replace the router.
I would upgrade the firmware before deciding to replace router with a new one. I noticed there have been several updates to the firmware since I originally installed the router with the current available firmware version of 1.35NA.
View 12 Replies View RelatedWe are close to receiving our new 6513E chassis which I will be running Sup720 cards in. This will be replacing our existing 6509 Sup2 setup in production. What current IOS version should I run on the Sup720 ? I would like to support SSH. The chassis will be populated with a couple of 6724 SFP cards, 2 6704 10 gig cards and a few 6748 line cards.Is there a good intitial config guide ?
View 6 Replies View Relatedupgrade experience with the 6509E on what IOS version to use. This is a new install, so I want the most current version that supports SSH and works with dual supervisors.
Here is some information:
WS-C5609-E with 983008K/65536K bytes of memory
Current version 12.2(18)SXF17b
Slot 5 Supervisor 720 (Active)
Slot 6 Supervisor 720 (Hot)
Just need a strong base code, no advanced services. Let me know if you any additional information.
My router password is "55xxxxx"
But when I want to change the router password in CCC, it warns me "Current password is not match"
I have an old WRT54G and the access restrictions really don't work. it's sloppy and ineffective.
i'm thinking about upgrading... perhaps to the E2500. Do the access restrictions now work properly? Am I able to allow access to a specific site only during certain times?
For instance, am I able to provide access to [URL] only during 6:00pm-9:00pm and block it otherwise?
how to change the time zone, the current time always show Firmware Version:1.01.6Current Time:Sat, 1-Jan-2000 00:08:40 and can't connect PPPOE
View 1 Replies View RelatedComcast service went down in our neighborhood and when it came back up my internet was down and all five LED lights on my Linksys router are solid green. Tech support tells me that I have to reset the unit to get it to function again.It's been a very long time since I set up the home network and while I'm pretty sure I can make my way through setting up from scratch (I'm assuming resetting goes back to factory settings) I was hoping there was a way to reconnect the router to the modem while retaining all the current security and settings.
View 2 Replies View RelatedI have both a Sony XBR52HX909 and a Sony BDP-S580 connected to my router (WRT54GL)via ethernet. When I try to connect to the internet, both show the wired connection as good but neither can connect to the internet. The BDP-S580 also has wireless connectivity, but it can’t connect to the internet wirelessly. I have two desktop computers connected via ethernet and two laptops connected wirelessly to the same router and all have internet connectivity. I have tried the “auto” settings on the TV and Blu-Ray player and also tried entering the network information in manually. I still can’t connect to the internet.
View 5 Replies View RelatedLast week suddenly my internet connection failed. I have tried several times to establish the wireless internet connection. Everytime when i tried to do this, i get the message 'can not get IP address'. Already tried to upgrade the firmware but still same message appears.
View 4 Replies View RelatedI want to use my router to boost the signal to the 2nd floor of my house, and Im having some problems.When I connect my router to the web application to change restore it to manufaturer setting the router keeps broadcasting my old SSID. The laptops in the house pick up that signal. I want to reset my router so it can broadcast my new network.
View 2 Replies View RelatedI have Wireless-G Broadband router Model WRT54GL. Everything is all setup correct but consoles and handhelds can't get the IP address even if there connected to the router. It isn't intill I turn off and then it back on does it get the ip address.
View 2 Replies View RelatedI'm trying to use a WRT54GL with U-Verse. The problem is that the router does not get a connection to the modem. It can't ping the modem, and it doesn't show up on on the list of devices connected to the modem. DHCP assigns an IP address of 127.0.0.1, which is outside the range of the modem [192.168.1.1 ... 192.168.1.253]. The router is also showing a default gateway of 0.0.0.0, and a subnet mask of 255.0.0.0. (And yes, I have released and renewed the lease, rebooted the modem, and reconnected the modem.) The router WAN side is set to DHCP, and the operating mode was changed from gateway to router (the gateway setting doesn't work either, for that matter).
View 9 Replies View RelatedI currently own a LinkSys-WRT54GL 802.11a/b/g wireless router, and my ISP is Comcast Cable providing me with 15 Mbps (that's bits per second, I believe) download speed. I am wondering if there is any benefit with using an 802.11n wireless router to access the Internet? The maximum theoretical speed of the WRT54GL router is 54 Mbps (802.11g), which is faster than the 15 Mbps provided by my ISP.
I know that 802.11n has a max bandwidth of 300 Mbps, and it would work for intra- house transfers, such as streaming video from one computer to another.
But is there any benefit to 802.11n for Internet activity, such as web browsing, gaming, and streaming video from Netflix.
I had configured the AAA server on CoovaAP and was able to access the internet.I had configured the user name and password as a "testuser" and "password" respectively. With that user id i used to access the Coova AP router and internet.Now i want restore the WRT54GL firmware on Lynksys router. But with the used id and password which i had configured the router is not at all accessible. So i did 30-30-30 reset on the router 2-3 times. Now i can see openwrt login page with 192.168.1.1 IP address. It is asking for user id and password. I tried all the combinations of user id and password, but no luck. I browsed some link on the internet and some people have recommended that default user id as a "root" and blank password. But with that also the router is not accessible. I cant to do much on the router untill i will log in to router. I have spent lot of time on this. How to restore back the original WRAT54GL firmware on my router. Anyhow i want WRAT54GL firmware on Lynksys router
View 4 Replies View RelatedI recently had to unplug my Linksys WRT54GL wireless router when doing some rearranging and now i'm unable to get a internet connection. I've confirmed the modem is actually working by connecting my laptop directly (which worked), but when I connect the Linksys WRT54GL wireless router to my modem the internet connection goes away. The connection is lost when connected via wireless and hardwired to one of the back ports. I've tried resetting the modem, router and computer and read every forum out there trying to find something, but i'm still stuck.
View 5 Replies View RelatedI have a problem with my linksys WRT54GL router. I entered here [URL] and i set it up, i can connect to internet on my PC and wireless works great but i can't set wireless password and name. When i go to the wireless tab, i write the new name but when i hit seve setting i get disconnected from internet. I try to go to status and click on Connect tab, when is connected internet works but the name and the password of the wireless that i set earlier is reset to default. What do i have to do to set name and password and have internet at the same time.
View 7 Replies View RelatedI would like to connect my old WRT54G3G router to my new WRT54GL (connect to dsl modem) and have wireless on both activated.I have set both on different channels with same SSID and same passwords on WPA2 Personal AES.I have also made the network IP different WRT54G3G 192.168.0.99 and WRT54GL 192.168.0.98.I have also deactivated network DHCP on 192.168.0.99. and Operating mode to router and still not working.
View 1 Replies View Relatednot being able to block websites like facebook and youtube on the router.
View 4 Replies View RelatedI am using a WRT54GL for the free wifi service at my business. Is there any way to set it so that when someone accesses the internet they are directed to my business home page first?
View 1 Replies View RelatedI want to use a linksys router with a 3com switch. 3Com model 3CGSU08A.i have two routers to choose from a E2000 and a WRT54GL which one is better and settings to use.
View 1 Replies View RelatedWe have received from a customer of us an WRT54GL box configured with a Coova software. This Wifi router was supposed to be a Wifi hotspot, but was not configured by us. This box is able, on startup, to get an IP by DHCP, to touch a remote Radius server, and so on (we "tcpdump" the Internet traffic, and we saw DNS requests, radius requests, ...)...
But, we are unable to connect to this box,by SSH or by HTTP, either by plug-in PC to the Internet RJ45 or the LAN RJ45. It has no IP as 192.168.1.1. Instead, it was configured to have 192.168.1.1 as gateway.
Of course, we have no doc on previous install, but only the admin/root password for SSH.We are afraid to lose the config (coova, ...) if we perform a hard reset.What is the best way for connecting on this box ?
Why this router have DHCP server and Port forwarding features and many LAN ports, but does not have DHCP reserve feature? If I can plug many computers, each one get own IP address, but how I can't fix it? I need to port forwarding of course, but if lease time ended, next time my computer got other IP address, so I need to reconfigure port forwarding each time! Of course I can do it, but try to explain it for your wife? Yes, I can use static IP addresses, but for what this box have DHCP server?
View 9 Replies View RelatedI accidentally pressed the front panel button labeled "Cisco Systems" on my WRT54GL wireless router. The button turned to a flashing white which I understand means that it entered SecureEasySetup mode. I then power cycled the router and the front panel button turned back to solid orange. However, now the "WLAN" lamp flashes a lot more often than before even when there are no wireless clients connected. It doesn't seem to be affecting connectivity or performance of my Ethernet connected devices or wireless connected devices. I re-entered my SSID and security key. That didn't curtail the increased flashing of the WLAN lamp. I also tried pressing the front panel button for 5 seconds. This only cleared my wireless settings.
View 2 Replies View RelatedI have a 16mbps (megabits) cable modem that is connected to WRT54GL. Desktop is located next to router and is connected with a cable, Laptop is connected on Wi-Fi. Both PCs achieve maximum speed when downloading from the internet but when I try to copy something from one PC to another over the local network I get stuck on max 2.5-3MBps (megabytes).
View 4 Replies View RelatedI'm using a WRT54GL(4.30.14) Router with a Charter Cable Modem running 5 computers on the network with 1 being wired and the rest are wireless. When my family comes over they can connect with their iPads and laptops but for some reason I can not get this iPhone 4G to connect. We put in the password and it says unable to connect. Are there any special settings that need to be made to the router to let the IPhone connect?
View 3 Replies View RelatedConnect my linksys WRT54GL router to the proxpn vpn privacy service as a client? (or any other vpn privacy service for that matter) I already have an internet connection up and live with a cisco router so I would need to connect the linksys to the cisco and use the linksys as a vpn gateway kind of thing, so that any computer connected to the linksys will automatically be in the vpn tunnel without needing any cleint software installed on it. The vpn service I use is proxpn but they won't support the settings of individual routers (understandable). The only setting they give for a PPTP connection is here
[url]...
I've had a WRT54GL ( for about a week now ) with no real issues. Today my wife mentioned that the net's been flaky ( wireless nto hard wired ). I originally noticed what seemed like minutes for my desktop of laptop to connect to any web pages. Loads were extremely slow. According to the computer I had a 1 mbps connection. I did the standard resetting of the modem and router.babble babble babble. Eventually, I ran a wifi analyzer from my phone to determine an ideal channel. However, while running the frequency scanner I also noticed that my broadcasting would continue to drop off the radar for a quick moment then return. This seemed to be true no matter what channel I set. What's interesting is that the signal would read as extremely strong for 45 sec - 1 minute, then completely drop the signal, then another strong broadcast. Other neighboring signals don't exhibit this behavior....well I would see the weaker signals coming in and off the radar from time to time. I'm guessing it's some type of interference? However if that's the case I can't explain why my signal seems so strong. I'm assuming I'd see a lot of fluctuation in my signal before dropping off ( instead of going from 100 to 0 in the blink of an eye ).
View 1 Replies View RelatedI have a wireless router and I'm trying to user UPnP feature. of course it is enble in the router.
It's working one and after it stop working, looks like the router is not responding anymore. If I got on the web interface of the router, I loging, on the first web page I press save changes, even if I didn't change anything, the UPnP feature work again.
Looks like a timeout occure or something like that. Is there a way to wake up the router without having to go on the web interface? Why it's stop working?
Firmware Version: v4.30.15
Router is setup as DHCP and only allows 7 IP address leases that expire daily. Lease time is set to 0. I have the latest firmware. Until recently when our family started using Apple iPhones (2 of them), I didn't have this issue.
Now I'm having a problem where my clients table will show leased IP's with no devices attached to them. I have to clear those no-name addresses so that the iPhones and other non-Apple wireless devices in the house can re-establish a connection.
How can I get those IP's to be removed without having to constantly log into the router and clear them?
I have two WRT54GL wireless routers. I have a computer and printer in my office connected to one of them. I'd like to add a computer and printer back in the shop to my network without using a wired connection. Can I use the 2nd wirelss router so that all computers and printers are on one network?
View 6 Replies View Related