Cisco Wireless :: VWLC - 1142N AP Not Broadcasting SSID?
Apr 7, 2013
I am running the demo of the virtual WLC and have one 1142N AP connected to it. I have two WLAN's created and they are configured to broadcast their SSID's. However, when I look on my laptop or Android, I cannot see either of them. I checked the AP to see if it has the WLAN's on it and it does. I did this by going to Wireless -> Access Points -> Radios -> 802.11a/n AP Interfaces -> Details. Under Station Configuration Parameters -> Number of WLAN's, there are 2, which is correct. I had this demo running on VMware workstation and had some bridging issues with it and thought that was the issue. I now have it running on ESX5.1 and am still having this issue. I am at a loss as to what is causing this problem.
View 2 Replies
ADVERTISEMENT
Sep 6, 2012
I'm facing a problem on vWLC. I configured the vWLC and Aironet 1252, I created 2 SSID with below settings.
1. WPA2 Auth 802.1X
2. Web-Auth
Inside Wireless, I configured this AP Mode as "Local", but all of the client device such as iPhone, Laptop can't find these SSID.
View 3 Replies
View Related
Jul 16, 2011
Several days ago I had to change my router. The new one works OK except that I can't get the PC to link into the wireless while the SSID isn't being broadcast. Having read that it is a good idea not to broadcast the SSID for security reasons, I thought I would try it!
I am running Windows 7 home Premium and the router is a Draytek Vigor 2710 using WPA2. I can see the network when the SSID isn't being broadcast, it just refuses to connect to it. As soon as I switch on the SSID it connects like a dream.
View 3 Replies
View Related
May 9, 2013
We've had a Cisco 881W set up in one of our remote offices for a while and the wireless has been fine. Yesterday I got a call saying that the wireless was no longer working.
I went over and it's true, the SSID is no longer broadcasting. I reloaded the router but it's still the same. I tried to get access to the embedded ap and I get this
RTR#service-module wlan-ap 0 session
% telnet connections not permitted from this terminal
RTR#
Now I've not changed anything on the configuration since it went in and it was working before. Has the embedded ap died? The embedded ap is still showing as a component in show hardware.
View 15 Replies
View Related
Sep 28, 2012
I configured the device manually, not even using Express Setup or Express Security setup so... it is possible I missed something.Anyway, here's the problem. Although the SSID is configured as "AP1", this SSID does not appear among available networks on the client laptop.
The connection, configured in Group Policy for the client, should actually happen automatically, based on the SSID, but since the SSID is not being broadcast, that connection is failing as well.
The Aironet does appear among the available networks as "Other Network" and if I click on "connect" I am prompted to enter the SSID -> AP1
Although, unexplicably, an error message displays (Windows cannot connect to the network, or something to that effect), the laptop *does* connect once I close that window. Network access is complete and functional - I can ping other hosts, etc..
I'd post screenshots but not knowing what setting is missing or incorrect, I'd have to print dozens. So here's the sh run output of the AP obtained via telnet (just below). This is a test network so all information is "real" (nothing changed for privacy):
Note: I even changed the hostname to "AP1" (it's still LAB1 below) but that did not resolve the problem (did not think it would).
LAB1#sh runBuilding configuration...
Current configuration : 2321 bytes!version 12.4no service padservice timestamps debug datetime msecservice timestamps log datetime msecservice password-encryption!hostname LAB1!logging rate-limit console 9enable secret 5 $1$9EWD$kxrbg8KxikRFypOieKiZh/!aaa new-model!!
[Code]....
View 5 Replies
View Related
Jan 28, 2013
I have Build a 5508-HA Cluster (7.4.100.0) , hat to reboot this cluster due to Licens install.After the reboot atleast one of the SSIDs was not broadcasting anymore, even the checkbox was checked.
What did I do:
Installed the Licenses @ Freiday 12:00
@17:15 reload active WLC, wait till controller is up again (a few minutes pingable)
@17:25 force failover to first controller.
check a few SSIDs but not all, those who where check are ok.
@monday 07:00 clients complaining not seeing the SSID (some where connected)
View 6 Replies
View Related
Oct 12, 2011
I have two 1142n LWP ap converted into standalone, as client doesn't have any controller there. They just want to extend their network via wireless.
L3 switch (trunk port gig 1/48) -----> connected to AP1
L3 switch (trunk port 2/48) -----------> connected to AP2
client is looking for 3 vlans on the floor ( users might multiple vlans might associated same AP ). They have a dedicated DHCP/DNS server and he will be configuring 3 vlans on L3 switch with correct ip helper address on SVI interfaces.
I'm i allowed to created 3 SSID's on 1142n standalone AP ?
What would the various optiosn to achieve this requirement ? Is there any simplest way to achieve this ? Do i need to go for 802.1x ? I remember client told their users are authenticating by using AD for wired network. This is their first request for wireless environment
View 2 Replies
View Related
Apr 18, 2012
SSID is not being broadcast from an e3200. I split the wireless networks and assigned a new name for the 5Ghz band. The broadcast SSID button is enabled for both networks. (2.4 & 5). The idea is I want to stream video on the 5Ghz band. Nothing seems to see it though, TV other PCs, etc.
View 1 Replies
View Related
Apr 2, 2013
I have around 60 , 1142 N APs . As of now i have only management VLAN ( for IP ) & one user vlan 350 configured on the access point . All the users connect to VLAN 350 and they get IP as required.However in our new set up there are couple of requirements have come up were in SSID will be the same however we have created many VLANs for different kind of user group and all these VLANs should be mapped to this single SSID and pick the IPs from their respective VLANs .
We have done configuration on the RADIUS server side were in we have mapped the users in their respective VLANs and they are getting authenticated via AD . Now how do i map my these 4-5 VLANs in a single SSID in Access Point.
View 16 Replies
View Related
Oct 9, 2012
I just set up my new Linksys 3200 router and wanted to know if i should turn SSID boradcasting feature off?
View 2 Replies
View Related
Aug 20, 2011
I changed the 5 GHZ SSID name using Cisco connect on my E3200 router as was expecting to see 2 available wireless networks on my laptop, but it seems that only the 2.4 GHZ is still broadcasting as it was before. When I connect to it with my laptop it shows it connecting with 802.11n, so I would think that my laptop would see the 5 GHz SSID if it was broadcasting. I am trying to take advantage of the dual band feature and connect the 5 GHZ to my blue ray player for real time video streaming.
View 9 Replies
View Related
Nov 10, 2011
So I have this E1500 Router that worked fine for the past 5 months, then out of the blue, the wireless feature ceased to function... laptops were not being able to connect to the wireless, the router was also not broadcasting the SSID.So, here's what I have done so far:
1. Check the router software settings, all was good there.
2. Did a "hardware reset" pushing the red button. (now this solved the problem, BUT only for a day, when power is turned off for the night, the next day it's non-functional again. The cycle can be repeated daily, but its a pain to reset and set it up everyday)
3. Updated the Firmware, and this somehow solved the problem for 3 Days... and now it's back to non-functional, again out of the Blue.
Is the Router just busted and it's not remembering the settings?
View 2 Replies
View Related
Oct 1, 2011
i have 2 DIR 615 routers which both stop broadcasting SSIDS. Ive had only one connected at a time, thinking it was a bad router, but both behave the same way. Is this a known issue or something ? What happens is, after some time (it varies..sometimes 3hours..sometimes longer), the router stops broadcasting the ssid, and I can no longer connect any of my wireless devices to it. The hardwired connection does work (I have a server connected to it, and it appears to work).The only settings I have changed is my SSID name, and wpa2 password. I've set up one virtual server to port forward requests to the server. Thats it. Nothing complex or anything. And both routers behave the exact same way, meaing they stop broadcasting the SSID.
View 8 Replies
View Related
Aug 2, 2011
I have a Cisco 5500 Series Wireless LAN Controller Model No. AIR-CT5508-K9
I have HREAP groups in Boulder, CO, Boston, MA, and Amsterdam, NL.
The LWAPPS act perfectly in the states (all AIR-LAP1142N-A-K9). The unit AIR-LAP1142N-E-K9 in Amsterdam will not allow any clients to attach unless the SSID broadcasting. I don't want to broadcast SSID. I have used iPhones and Intel 5100 series wlan cards. I don't get it. I have been working with Cisco for weeks. We have even replaced the LWAPP.
I am getting this from the ASA in Amsterdam:
6 Aug 03 2011 20:20:22 PMTU-D packet 1485 bytes greater than effective mtu 1426, dest_addr=wificontroller, src_addr=LWAP, prot=UDP
I don't understand because the mtu on the outside interface is 1500 I guess "effective" is the key word which I missing here.
View 16 Replies
View Related
Jan 31, 2012
I have a "standart" settings of Cisco Aironet 1240AG with ENABLED broadcasting SSID, encryption is WPA2 (AES). I can see the wifi network (ssid) with windows system but with MAC OS 10.5 and MAC OS 10.7 also with iPhone the wifi is acting like hidden. But If I manually enter the wifi ssid and set the proper encryption the connection work normally. Also I have a separete windows partition on one MACbook and this windows 7 have no problem to see the SSID of my network. But If i Boot to the MAC OS the WIFI is "hidden" until the manually connection. (same problem on iphone, manuall connect with manually entered SSID is working well).
View 2 Replies
View Related
Sep 30, 2011
I have a linksys WRT54G that has been bugging out a lot. It stops broadcasting the SSID briefly and won't start again until it reboots. Annoying enough problem on it's own, but not my primary concern.My concern now is that when I tried to upgrade the firmware to the latest version (which I presume was causing the problems) the router now is essentiallyunresponsive. The upgrade was successful according to the control panel site, but ever since the required reboot as part of the upgrade process the router hasn't worked properly. 1) The power light blinks constantly rather than staying lit.2) When I plug directly into it sometimes I get access to local networks and other times I don't (limited connectivity). But I never get access to the internet if it's plugged into it as well.3) When I try to go to the control panel site (through the 192.168.1.1) the site wont loadGranted this router is old, but it was working fine other than dropping the broadcast every once in a while. It did need a firmware upgrade, but the upgrade seems to have been a bad choice
View 3 Replies
View Related
Mar 6, 2013
Does the Cisco vWLC support the cisco AIR-AP1231G-A-K9 platform?
View 4 Replies
View Related
Mar 7, 2013
Below are the errors that i am getting while trying to register AP (2606e) with vWLC (7.3.112) .
That is the error on vwlc
[code]....
But in wlc statistis we are able to see the ap join mac, screen shot is attached
View 6 Replies
View Related
Feb 17, 2013
i have installed ISE1.1 on VM and other hand vWLC7.4 also there in VM i am using 1130AG APs in flexconnect mode and using central auth and central switch.i wan to configure it for CWA(central web Auth) from ISE but a little a bit confuse about ACLs.
View 2 Replies
View Related
Mar 13, 2013
I am looking at deploying a Cisco Virtual Wireless LAN Controller (vWLC 7.3).
Do I need Prime Infrastructure to manage the environment, or can I manage my AP's (1200 series) using the vWLC alone?
View 1 Replies
View Related
Sep 9, 2012
Im using 1131AG AP.Locally switched WLAN don't have problem.Authentication used: open/wpa-psk/wpa2-psk.Pinging the IP Address of the vWLC dynamic interface (WLAN-SSID Mapping) is ok, but with the gateway failed.
View 12 Replies
View Related
Jan 24, 2012
I have run into a major issue with an autonomous Cisco 1142AP. We were in the midst of a firmware upgrade when something went wrong and caused the AP to reboot in an error mode. Basically the unit was flashing Blue, amber, red. We unmounted the unit from the wall, connected to the console, and it would now only flash red over and over. We pulled out the cisco guides and performed a factory reset on the unit. This still does not work. and the contents of our flash directory is empty. All we get is a ROMMON AP prompt on the unit. If I issue a set command, I can see the default settings for IP, netmask, etc.
I cannot access the unit via the network, even after setting IP info and matching it up to my laptop. Since I have no network connectivity, I can't TFTP a new IOS file to the unit. I am stumped. How to get the config as if it was out of the box, or an alternate way to TFTP to the unit? [code]Notice the lines in red, I must have typed someting incorrectly.Now once the unit boots after being reset, I cannot even type in the CLI. Someting majorly screwed up here. Can the bootstrap be reinitialized?
View 3 Replies
View Related
Dec 6, 2011
Now, with all the unified communications, voice, video and data are in the same device, and I try to give priority to voice and some applications, but in the WLC I can not find the way to mark all that kind of packets.
Is it possible to do that? like in a LAN making the marking as voice, signaling and any kind of application? as I marked in all the LAN.
the equipment:
WLC 5508 v7.0.116
AP 1142N
View 5 Replies
View Related
Jul 10, 2012
I been using 1142n Autonomous several times.Now i have new requirement to setup 12 LAP 1142n, using a WLC.Can suggest what model of WLC should i choose?? About 30 users, in a cargo warehouse invironment.Now it is a good time for me to learn & play around with WLC.What else should i need in order for LAP & WLC to work??
View 7 Replies
View Related
Apr 30, 2013
Need to configure Cisco 1142 N access Point togetherwith the Cisco Switch . I have a POE Switch 4510 and Cisco 1142 N Cisco AP . I have one management vlan 5 & User VLAN for WIFI VLAN 10 . The problem is when i make the POE port which is connected to the AP as trunk port means : [code]I am not able to ping the management IP allotted from VLAN 5 . However when i make it as access i am able to ping the managament IP . But for both the VLANs to work it should be in trunk mode & in cisco i can either assign the port as access or trunk .Post this i would configure the 1142 N with Cisco SG300-10P POE Switch . I guess if issue with my 4510 gets resolved the same way i can configure SG300-10P as well .
View 6 Replies
View Related
Apr 16, 2013
I just purchased an Aironet 1142n and need to configure/set it on one subnet in our WAN and ship it to another subnet on the WAN.
I have not been able to access the unit using a network cable from a pc direct connected to the Aironet. The pc's ip address is set to 10.0.0.2 I can not get to the access point thru the web interface using 10.0.0.1.
When I attempted to access it using a Hyper terminal connected to serial port and console port it loaded a list of software and updates and then reported that it shut down and I could not do any thing with it.
What must I do to be able to configuer a static IP and assign it an SSID and Security settings? How can I access the web interface? I have reset it by uplugging the power cord and holding down the Mode button while I plugged back in the power cord and holding it until the light turned amber/orange. Currently the light is solid green with the ethernet port direct connected to the nic card on a desktop.
View 4 Replies
View Related
Jun 6, 2012
I have a question with the CAPWAP command. Typically, when I get 1142N from our provider, they have no configuration on them and all I need to do is enter 4 lines of code all starting with CAPWAP and then I have them join the controller and finish the config. This one I just received looks like it has an IOS image or configuration on it. (You can do a show run). I can: show CAPWAP - but I can not enter any CAPWAP commands. They are invalid input detected at marker. How to I get to the point where I can enter my CAPWAP commands ??
View 3 Replies
View Related
Apr 30, 2013
I have two SSID's configured and I want them both on G and N but it looks like the speed is some way limited to 54mbps. I guess the encryption is not the problem as it's ciphers aes-ccm which support higher N-speeds.
my running config attached, that should be lovely as 54mpbs is too slow
View 11 Replies
View Related
Feb 9, 2012
How can I have access to the cisco "AP#" prompt? When I try to acees the AP through hyperterminal, it gives me the attached messages. The message keeps looping and not letting me access the AP# command prompt to assign an IP address so that I can control it in mode HTTP.
View 2 Replies
View Related
Sep 30, 2012
I am currently switching out our Cisco 1130 APs and Cisco Small Bussiness APs for Cisco 1142Ns (I will NOT be using a WLC),
I have setup the AP, and read about some issues with Multicast and Apple Bon. Services.
I ran the "no ip igmp snooping" command and it allowed be to access our AirPlay Devices (Apple TV, AirPort Express, Etc), however our 2 AirPrint devices (Xerox 6125N, & Canon IR3220 via AirPrint Activator) are not showing up at all when connected to the 1142 (they work everywhere else).
Everything is on the same subnet, and 1142 is connected to the same switch has the airprint devices, and one Apple TV.
Both our 3500 Series switches are connected via fiber, AP and AirPrint/AirPlay devices are in the same VLAN.
View 10 Replies
View Related
Jul 31, 2012
10 Access Pointd 1142N setup on vlan 10 and the controller management is in vlan 10.
They get DHCP IP addreses from the controller itself!! I do not have another DHCP server.
Here is what I get wich debug capwap event and debug capwap packet
(Cisco Controller) >*spamReceiveTask: Jul 31 12:21:41.283: <<<< Start of CAPWAP Packet >>>>*spamReceiveTask: Jul 31 12:21:41.283: CAPWAP Control mesg Recd from 10.128.186.104, Port 51743*spamReceiveTask: Jul 31 12:21:41.283: HLEN 4,
[Code].....
View 9 Replies
View Related
Jun 19, 2012
I am testing our new wireless network using 1 Cisco 2504 wireless controller with 5 licenses 4 Cisco Air LAP 1142N Access Point I configured it very simple for testing There is only one interface and vlan is untaggetd There is also only one WLAN with one SSID Currently security setting is WPA + WPA2 + PSK (I also tested with no security setup) Wlan session time is diabled and controller user idle timeout is set to 1000000 (Max)AP boot version is 12.4.23.3 and ISO version is 12.4(23c)JA3 Problem is clinet(iphone) does not automatically associate with 1142N Access Point even after it learned network. Phone has to be authenticated again to connect to network same iphone can automatically associate with old 1220 Access point but not with New AP if I urn off and turn back on wifi from iphone, it does see the network but does not connect but I have to manually reconnect to it with password I want iphone to connect known network without reauthentication process after iphone's wifi function is turn on?
View 24 Replies
View Related
Oct 8, 2012
Need simple configuration for the Aironet 1142N? Optimally, I would like to place 802.11b/g traffic on the 2.4 GHz band and 802.11n traffic on the 5 GHz band.
View 2 Replies
View Related
