Cisco Wireless :: 1142N Works With AirPlay But Not AirPrint?
Sep 30, 2012
I am currently switching out our Cisco 1130 APs and Cisco Small Bussiness APs for Cisco 1142Ns (I will NOT be using a WLC),
I have setup the AP, and read about some issues with Multicast and Apple Bon. Services.
I ran the "no ip igmp snooping" command and it allowed be to access our AirPlay Devices (Apple TV, AirPort Express, Etc), however our 2 AirPrint devices (Xerox 6125N, & Canon IR3220 via AirPrint Activator) are not showing up at all when connected to the 1142 (they work everywhere else).
Everything is on the same subnet, and 1142 is connected to the same switch has the airprint devices, and one Apple TV.
Both our 3500 Series switches are connected via fiber, AP and AirPrint/AirPlay devices are in the same VLAN.
View 10 Replies
ADVERTISEMENT
Jan 21, 2013
Recently i converted a customer's APs to LWAP and installed a 2504 WLC. Everything came up and is acting good, but the printer is no longer printing. It can neither be discovered using windows networking, nor bonjour. It worked until LWAPP conversion.
It is an AirPrint device, a Canon mx892. Trying to print using an IP port fails, AirPrint fails, and sharing it through the attached Mac also fails. I dont know enough about printers or AirPrint to effectively troubleshoot. The customer opened a case with Canon, who says its a network issue. I cannot get it configured on the wire, apparently setting up a printer isnt as easy as it used to be.
View 1 Replies
View Related
Jan 24, 2011
My WAG120N does not allow airprint from ipad/ipod to HP photosmart wireless printer. When i replace the linksys router with an old netgear one all works well and the ipad can find the printer and print. Enable the Linksys router and the printer is no longer found on the ipad. other forums suggest this relates to handling of the Bonjour protocol ... any resolution for this so i dont have to go back to legacy speed on my home wifi?
View 3 Replies
View Related
Dec 31, 2012
I bought a Canon Pixma mg3220 all in one printer/scanner today. I specifically picked it for the Airprint feature for my IPhone, which I can't get to work. Is it a problem with my F5D7234-4 v5 router? I have updated the firmware and it still won't print. The Iphone sees the printer, but that's as far as I get.
View 2 Replies
View Related
Dec 27, 2012
I cannot airprint. Contacted email support. Followed instructions to reset router. I did and I was able to print from my iPhone. ONCE. Then I installed my SSID and passwords and WIFI setup again and now I can't print. I have a brand-new airprint equipped HP 7520, an iPhone and 2 iPads.that I want to print from....the router is a N750 AV bought in July.
View 1 Replies
View Related
Jul 19, 2011
I know Airplay isn't meant to be done across vlans, but surely it should work with things on the same vlan.The 541N's are clustered and have WDS enabled. The wireless VAP's are on the same VLAN, and intervlan routing works. Airplay works if the iDevice and the Apple TV are connected to the same access point, but not across the network.
View 1 Replies
View Related
Jan 2, 2012
I am having a trouble with using iTunes, iPhones and iPads on our Wireless LAN. We have the 2112 WLC and 10 1142N WAPs. If I do a network scan, I can see the Apple TV and see that port 5353 is open, which is Apple's Bonjour service. However, if I try to play music/video in iTunes, or on an iPhone/iPad, I do not see the Airplay icon. If I plug into the LAN, the Airplay icon appears immediately. I have created an allow all rule in the ACL but still no dice.
View 26 Replies
View Related
Oct 16, 2012
I have a Cisco Wlc 4402 , denon 3312 & AP 1142 all three devices are same subnet . But Airpaly not showing in Iphone. But if i put a Airport express in on these subnet then i find airplay option. How without Airport express i can enable airplay...
View 2 Replies
View Related
Dec 6, 2011
I've got 3 WLC 4402 controllers and the wireless is working perfectly except for 1 issue. We are trying to connect an apple tv, so we can stream picture, videos etc from ipads and Macbooks to a large display for media teaching.The setup works at home, but not at work.The apple TV is on the same network as the wireless apple devices, (we use a 10.6.4.x-10.6.5.254 range), both are dhcping the addresses (have tried fixing but that made no difference). I've enabled multicasting and igmp snooping and set the multicast address as 239.0.0.0 and it still doesn't work.
View 11 Replies
View Related
Dec 22, 2011
I have an issue when I use Airplay through my iPhone4S, my router reboots after 30 secs or so. I have a WRT54G2 v1.5 and the receiver is a Pioneer VSX-1021-K.
However, when I used Airplay through itunes from my laptop, it works just fine. In addition, when I borrowed my neighbors router's(BELKIN) it was working fine also. So this lead me to believe that it's my router that is causing the issue.
View 7 Replies
View Related
Oct 13, 2011
I have 2 X E4200 router, one is directly connected to the internet and the other is in the bridge mode connected to the first router. I have apple TV connected directly with the bridge router on one of the Ethernet port.I notice that when you start apple Airplay mirroring on the iPad2 both the routers will hangs with no reason and the only way to fix it is to reboot the routers. I have reset both the routers to factory default twice they both are running firmware 1.0.03 build 14 .
View 9 Replies
View Related
May 10, 2012
I have a DIR-665 and I'm trying to install a B&W zeppelin air speaker, the speaker detects the wireless network but I cant see the airplay logo in the PC, mac, ipad or iPhone. Try with another router and ir works. try with a wired cable but still the same problem. IS there any issue with this routers and airplay, ATV or similar items? [code]
View 3 Replies
View Related
Oct 16, 2011
I've just confirmed that everytime I try to stream music from my MacBook Pro (iTunes) that is connected to my WiFi network using the 5GHz mode (channel width is Auto, channel: Auto (DFS)) to a couple Airport Express cubes are connected via the 2.4 GHz WiFi (channel width: Auto, channel: 10) the E4200 router reboots. When I set the MBP to use the 2.4 GHz mode I can stream music without causing the E4200 to reboot. The E4200 is running firmware 1.0.03.
View 9 Replies
View Related
Feb 20, 2012
what Linksys routers, e.g. WAG120N, are compatible with Airplay and Bonjour?
View 9 Replies
View Related
Nov 13, 2011
My problem is this: Randomly, the DIR-825 will prohibit streaming to my AirPort Express via AirTunes. It'll also disappear from Bonjour Browser and AirPort Utility. I can connect directly to it, if I enter the IP into the AirPort utility directly.The only way to get it to come back is to either reboot the DIR-825, reboot the AE, or unplug the ethernet to the AE.
View 3 Replies
View Related
Apr 8, 2013
I have a problem running Airplay through the wireless on my W881. It runs okay if the computer i run it from, does nothing else, but if i try to do light browsing or anything like that it starts to fall out and lag. Its like it is not prioritizing the stream at all.
My setup is a w881 running as edge router and i got an Airport express running through a 2950 switch. Airplay runs perfect if i run it through the Airport express or my previous Edge router (Linksys WRT54g). Ofcourse it also runs perfect through the wired network. I shut down all other wireless networks but my w881, because i only want one wireless. And no i dont want to run wireless on the Airport express.
i played around with the Dot11Radio0 interface setting "packet retries 128 drop-packet" and the packet "max-retries". I thought that maybe if i set max-retries to something low, it wouldnt fall out if it has some problems with one packet, it would just continue...
View 0 Replies
View Related
Mar 5, 2013
I have a problem when doing Apple Airplay mirroring from my iphone5. Every time it kmocks the wifi signal off so I need to reboot the router. This is only happening on the iphone 5, and not other apple devices using mirroring. Our ipad 3 mirrors perfectly without affecting the wifi. There isn't any specific settings on the iphone 5 for airplay apart from setting it on and off.
View 2 Replies
View Related
Jan 24, 2012
I have run into a major issue with an autonomous Cisco 1142AP. We were in the midst of a firmware upgrade when something went wrong and caused the AP to reboot in an error mode. Basically the unit was flashing Blue, amber, red. We unmounted the unit from the wall, connected to the console, and it would now only flash red over and over. We pulled out the cisco guides and performed a factory reset on the unit. This still does not work. and the contents of our flash directory is empty. All we get is a ROMMON AP prompt on the unit. If I issue a set command, I can see the default settings for IP, netmask, etc.
I cannot access the unit via the network, even after setting IP info and matching it up to my laptop. Since I have no network connectivity, I can't TFTP a new IOS file to the unit. I am stumped. How to get the config as if it was out of the box, or an alternate way to TFTP to the unit? [code]Notice the lines in red, I must have typed someting incorrectly.Now once the unit boots after being reset, I cannot even type in the CLI. Someting majorly screwed up here. Can the bootstrap be reinitialized?
View 3 Replies
View Related
Dec 6, 2011
Now, with all the unified communications, voice, video and data are in the same device, and I try to give priority to voice and some applications, but in the WLC I can not find the way to mark all that kind of packets.
Is it possible to do that? like in a LAN making the marking as voice, signaling and any kind of application? as I marked in all the LAN.
the equipment:
WLC 5508 v7.0.116
AP 1142N
View 5 Replies
View Related
Jul 10, 2012
I been using 1142n Autonomous several times.Now i have new requirement to setup 12 LAP 1142n, using a WLC.Can suggest what model of WLC should i choose?? About 30 users, in a cargo warehouse invironment.Now it is a good time for me to learn & play around with WLC.What else should i need in order for LAP & WLC to work??
View 7 Replies
View Related
Apr 30, 2013
Need to configure Cisco 1142 N access Point togetherwith the Cisco Switch . I have a POE Switch 4510 and Cisco 1142 N Cisco AP . I have one management vlan 5 & User VLAN for WIFI VLAN 10 . The problem is when i make the POE port which is connected to the AP as trunk port means : [code]I am not able to ping the management IP allotted from VLAN 5 . However when i make it as access i am able to ping the managament IP . But for both the VLANs to work it should be in trunk mode & in cisco i can either assign the port as access or trunk .Post this i would configure the 1142 N with Cisco SG300-10P POE Switch . I guess if issue with my 4510 gets resolved the same way i can configure SG300-10P as well .
View 6 Replies
View Related
Apr 16, 2013
I just purchased an Aironet 1142n and need to configure/set it on one subnet in our WAN and ship it to another subnet on the WAN.
I have not been able to access the unit using a network cable from a pc direct connected to the Aironet. The pc's ip address is set to 10.0.0.2 I can not get to the access point thru the web interface using 10.0.0.1.
When I attempted to access it using a Hyper terminal connected to serial port and console port it loaded a list of software and updates and then reported that it shut down and I could not do any thing with it.
What must I do to be able to configuer a static IP and assign it an SSID and Security settings? How can I access the web interface? I have reset it by uplugging the power cord and holding down the Mode button while I plugged back in the power cord and holding it until the light turned amber/orange. Currently the light is solid green with the ethernet port direct connected to the nic card on a desktop.
View 4 Replies
View Related
Jun 6, 2012
I have a question with the CAPWAP command. Typically, when I get 1142N from our provider, they have no configuration on them and all I need to do is enter 4 lines of code all starting with CAPWAP and then I have them join the controller and finish the config. This one I just received looks like it has an IOS image or configuration on it. (You can do a show run). I can: show CAPWAP - but I can not enter any CAPWAP commands. They are invalid input detected at marker. How to I get to the point where I can enter my CAPWAP commands ??
View 3 Replies
View Related
Apr 30, 2013
I have two SSID's configured and I want them both on G and N but it looks like the speed is some way limited to 54mbps. I guess the encryption is not the problem as it's ciphers aes-ccm which support higher N-speeds.
my running config attached, that should be lovely as 54mpbs is too slow
View 11 Replies
View Related
Feb 9, 2012
How can I have access to the cisco "AP#" prompt? When I try to acees the AP through hyperterminal, it gives me the attached messages. The message keeps looping and not letting me access the AP# command prompt to assign an IP address so that I can control it in mode HTTP.
View 2 Replies
View Related
Apr 6, 2011
this computer was working on this router no problem. computer crashed and noiw computer is fine i connected it to my cable from ny desk top comutyer and works fine. It just cannot hook up to the wireless connection?
View 1 Replies
View Related
Jul 31, 2012
10 Access Pointd 1142N setup on vlan 10 and the controller management is in vlan 10.
They get DHCP IP addreses from the controller itself!! I do not have another DHCP server.
Here is what I get wich debug capwap event and debug capwap packet
(Cisco Controller) >*spamReceiveTask: Jul 31 12:21:41.283: <<<< Start of CAPWAP Packet >>>>*spamReceiveTask: Jul 31 12:21:41.283: CAPWAP Control mesg Recd from 10.128.186.104, Port 51743*spamReceiveTask: Jul 31 12:21:41.283: HLEN 4,
[Code].....
View 9 Replies
View Related
Jun 19, 2012
I am testing our new wireless network using 1 Cisco 2504 wireless controller with 5 licenses 4 Cisco Air LAP 1142N Access Point I configured it very simple for testing There is only one interface and vlan is untaggetd There is also only one WLAN with one SSID Currently security setting is WPA + WPA2 + PSK (I also tested with no security setup) Wlan session time is diabled and controller user idle timeout is set to 1000000 (Max)AP boot version is 12.4.23.3 and ISO version is 12.4(23c)JA3 Problem is clinet(iphone) does not automatically associate with 1142N Access Point even after it learned network. Phone has to be authenticated again to connect to network same iphone can automatically associate with old 1220 Access point but not with New AP if I urn off and turn back on wifi from iphone, it does see the network but does not connect but I have to manually reconnect to it with password I want iphone to connect known network without reauthentication process after iphone's wifi function is turn on?
View 24 Replies
View Related
Oct 8, 2012
Need simple configuration for the Aironet 1142N? Optimally, I would like to place 802.11b/g traffic on the 2.4 GHz band and 802.11n traffic on the 5 GHz band.
View 2 Replies
View Related
Apr 30, 2012
My co-workers and I have been trying to diagnose a problem that recently started occuring on our AP1141N and AP1142N units. I have found a handful of posts that talk about this issue, but none with a solid solution. It seems that as often as every 24 hours, the radio interfaces change state to down, for seemingly no reason. Once this occurs, the only way to bring the radio interface back up is to reboot the AP. As far as we know, this wasn't happening until recently, when we enabled the "N" speeds. Things were working correctly for a year or two while the APs were configured just for b/g operation. The following is the only seeminlg-relevant thing that shows up in the logs:
*Nov 12 00:53:02.508: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Nov 12 00:53:03.507: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
Some additional info:
- All of the APs are connected to PoE Cisco c2960 switches
- We have tried both hard-coded radio channels, and non hard-coded
- We have tried various ways setting power inline negotiation
- We are not using a WLC
- System Software Version: 12.4(21a)JA1
- Bootloader Version: 12.4(18a)JA3
I have attached output of sh run, sh log and sh controlers dot11Radio0. (Another oddiy - the line %DOT11-2-RESET_RADIO hasn't shown up in the other logs I have viewed after this issue occurs...)
View 8 Replies
View Related
Aug 1, 2012
I would like to enable "client isolation" on an autonomous, standalone 1142N AP but I don't see that option anywhere in the web interface. how to keep associated clients from passing traffic to one another on this AP?
View 6 Replies
View Related
Jun 7, 2012
I'm looking for a way to monitor client authentication failures with our 3 standalone 1142N APs. I know that I can see failures under the log viewer of each AP
View 4 Replies
View Related
Jun 18, 2012
I have 14 unit of Air-AP1142n. No controller. All unit were in a warehouse, each of the AP distance each other around 40mI would like to use only 4 SSID instead of 14 SSID.
View 5 Replies
View Related
