I know Airplay isn't meant to be done across vlans, but surely it should work with things on the same vlan.The 541N's are clustered and have WDS enabled. The wireless VAP's are on the same VLAN, and intervlan routing works. Airplay works if the iDevice and the Apple TV are connected to the same access point, but not across the network.
View 1 Replies
I am currently switching out our Cisco 1130 APs and Cisco Small Bussiness APs for Cisco 1142Ns (I will NOT be using a WLC),
I have setup the AP, and read about some issues with Multicast and Apple Bon. Services.
I ran the "no ip igmp snooping" command and it allowed be to access our AirPlay Devices (Apple TV, AirPort Express, Etc), however our 2 AirPrint devices (Xerox 6125N, & Canon IR3220 via AirPrint Activator) are not showing up at all when connected to the 1142 (they work everywhere else).
Everything is on the same subnet, and 1142 is connected to the same switch has the airprint devices, and one Apple TV.
Both our 3500 Series switches are connected via fiber, AP and AirPrint/AirPlay devices are in the same VLAN.
I am having a trouble with using iTunes, iPhones and iPads on our Wireless LAN. We have the 2112 WLC and 10 1142N WAPs. If I do a network scan, I can see the Apple TV and see that port 5353 is open, which is Apple's Bonjour service. However, if I try to play music/video in iTunes, or on an iPhone/iPad, I do not see the Airplay icon. If I plug into the LAN, the Airplay icon appears immediately. I have created an allow all rule in the ACL but still no dice.
View 26 Replies View RelatedI have a Cisco Wlc 4402 , denon 3312 & AP 1142 all three devices are same subnet . But Airpaly not showing in Iphone. But if i put a Airport express in on these subnet then i find airplay option. How without Airport express i can enable airplay...
View 2 Replies View RelatedI've got 3 WLC 4402 controllers and the wireless is working perfectly except for 1 issue. We are trying to connect an apple tv, so we can stream picture, videos etc from ipads and Macbooks to a large display for media teaching.The setup works at home, but not at work.The apple TV is on the same network as the wireless apple devices, (we use a 10.6.4.x-10.6.5.254 range), both are dhcping the addresses (have tried fixing but that made no difference). I've enabled multicasting and igmp snooping and set the multicast address as 239.0.0.0 and it still doesn't work.
View 11 Replies View RelatedI have an issue when I use Airplay through my iPhone4S, my router reboots after 30 secs or so. I have a WRT54G2 v1.5 and the receiver is a Pioneer VSX-1021-K.
However, when I used Airplay through itunes from my laptop, it works just fine. In addition, when I borrowed my neighbors router's(BELKIN) it was working fine also. So this lead me to believe that it's my router that is causing the issue.
I have 2 X E4200 router, one is directly connected to the internet and the other is in the bridge mode connected to the first router. I have apple TV connected directly with the bridge router on one of the Ethernet port.I notice that when you start apple Airplay mirroring on the iPad2 both the routers will hangs with no reason and the only way to fix it is to reboot the routers. I have reset both the routers to factory default twice they both are running firmware 1.0.03 build 14 .
View 9 Replies View RelatedI have a DIR-665 and I'm trying to install a B&W zeppelin air speaker, the speaker detects the wireless network but I cant see the airplay logo in the PC, mac, ipad or iPhone. Try with another router and ir works. try with a wired cable but still the same problem. IS there any issue with this routers and airplay, ATV or similar items? [code]
View 3 Replies View RelatedI've just confirmed that everytime I try to stream music from my MacBook Pro (iTunes) that is connected to my WiFi network using the 5GHz mode (channel width is Auto, channel: Auto (DFS)) to a couple Airport Express cubes are connected via the 2.4 GHz WiFi (channel width: Auto, channel: 10) the E4200 router reboots. When I set the MBP to use the 2.4 GHz mode I can stream music without causing the E4200 to reboot. The E4200 is running firmware 1.0.03.
View 9 Replies View Relatedwhat Linksys routers, e.g. WAG120N, are compatible with Airplay and Bonjour?
View 9 Replies View RelatedMy problem is this: Randomly, the DIR-825 will prohibit streaming to my AirPort Express via AirTunes. It'll also disappear from Bonjour Browser and AirPort Utility. I can connect directly to it, if I enter the IP into the AirPort utility directly.The only way to get it to come back is to either reboot the DIR-825, reboot the AE, or unplug the ethernet to the AE.
View 3 Replies View RelatedI have a problem running Airplay through the wireless on my W881. It runs okay if the computer i run it from, does nothing else, but if i try to do light browsing or anything like that it starts to fall out and lag. Its like it is not prioritizing the stream at all.
My setup is a w881 running as edge router and i got an Airport express running through a 2950 switch. Airplay runs perfect if i run it through the Airport express or my previous Edge router (Linksys WRT54g). Ofcourse it also runs perfect through the wired network. I shut down all other wireless networks but my w881, because i only want one wireless. And no i dont want to run wireless on the Airport express.
i played around with the Dot11Radio0 interface setting "packet retries 128 drop-packet" and the packet "max-retries". I thought that maybe if i set max-retries to something low, it wouldnt fall out if it has some problems with one packet, it would just continue...
I have a problem when doing Apple Airplay mirroring from my iphone5. Every time it kmocks the wifi signal off so I need to reboot the router. This is only happening on the iphone 5, and not other apple devices using mirroring. Our ipad 3 mirrors perfectly without affecting the wifi. There isn't any specific settings on the iphone 5 for airplay apart from setting it on and off.
View 2 Replies View RelatedI just installed a WLC 5508, running 7.4 code. I can not seem to get the Airplay to work with apple TVs. The iPads and Airplay are on the same wireless network. What can I do to get it to work? Is there any documentation on how to get Airplay to work?
View 1 Replies View RelatedApple AirPlay won't work on AppleTV (from neither computer nor iPhone) with my new Cisco small busines router WRVS4400N. It was working just fine on old consumer level linksys router. I have spent 3 hours with Apple support to no avail. Apple TV works fine on internet functions (netflix, YouTube, etc.) and I can play music and videos from the cloud, but iPhone and computer can't connect to AppleTV even though the icons appear in iPhone and Computer... just can't establish a connection.
View 2 Replies View RelatedI just purchased an Apple TV 2 and am trying to use it with Airplay at my business. We have a WLC526 controller and three 521 access points.
We have a guest VLAN on our network which spans both the wired and wireless networks. The guest VLAN is VLAN # 100 and the numbering is 172.16.1.0/24. On this network, 172.16.1.1 is an interface on our ASA which clients on the guest VLAN use as a default gateway. On the wireless side, there is an SSID configured in the controller called LPGA-Guest which is bound to VLAN # 100. Clients that connect to this VLAN get addresses in 172.16.1.0/24 and can access the Internet through the ASA without any trouble. This has all been set up and working for quite some time.
What I have done is attached both the Apple TV and an iPhone 5 to the LPGA-Guest wireless network. I verified that they both have IP addresses in the same subnet, but when I try to bring up a list of airplay devices on the iPhone, nothing shows up. From what I gather, this is because multicast traffic is not being handled properly.
The following two threads have some info that I was looking at:
URL
URL
This is how I have the multicast options configured in my controller. I don't see an option to enable IGMP snooping.
Unable to use AirPlay on a D-Link network. Disable WMM in the Advanced->Advanced Wireless tab.I struggled for weeks with this. AirPlay worked fine on an all Apple network but when I switched to the DIR-655 as the router/ap AirPlay became invisible. I could see the Airport Express in the list of connected devices with an IP address but the AirPort utility and AirPlay enabled apps were unable to see it. Disabling WMM fixed it immediately and I am now back to streaming music.
View 14 Replies View RelatedWe have been successfully using our Aironet 1140 AP in standalone mode with mainly Windows pcs & laptop users, and now, iPads and iPhones. All seem to connect happily through the 1140.
Recently we have a requirent to be able to use Apple's Airplay. Basically, it is not working through the 1140, it works ok via wired ethernet. Can the 1140 support Airplay? - If yes, what precisely must be enabled/configured?
We have a single Class C network without any Vlans. I understand multicast must be enabled, I can't see where to enable this. How to get this working if it is at all possible.
Struggling to enable Airplay using a WAG160N. Any settings I need on the router? Looking on forums, came across suggestion to disable WMM support. This seemed to work and i had Airplay but now I've lost it again.
View 1 Replies View RelatedWhy does my belkin f7d4401 playmax router: allow iTunes and iPad/iPhone to see my Airplay B&W zeppelin Air when connected wireless but will not allow iTunes or my iPad/iPhone to see my Airplay Marantz NR1603 when connected via cat 5 cable. (I know the connection is fine on the NR1603, as it streams from internet radio with no problem at all)It seems to be just airplay that is not operational through the router.
View 2 Replies View RelatedI've got an apple Airport Express and have managed to set it into my network. Airplay works on both Itunes and my phone. However after 10-15minutes the Airplay drops out and the network map shows that the airport express is 'offline'. however the airport express LED remains showing it still have connection to the network. The only way to get it back is to reset the AE. The apple forum has lots of people stating the same problem with WAG120n routers.
-Router Firmware V 1.00.16
-Airport Express firmware version 7.6.1
-windows Vista
I need my security key
View 1 Replies View RelatedWe have a problem with AIR-LAP1142N access points.
AIR-LAP1142N-E-K9
Version 12.4(21a)JA
LAP's are not assotiated with controller yet. They get the ip address via dhcp, they are reachable by icmp.When I try to telnet, I get Password required, but none set? Is there any chance to get access to them without using serial port?
as the subject .. All those who have the WAP4410N ...want the new firmware 2.0.4.1 and solve the AP problems of stops an repeat. believe in CISCO.
View 28 Replies View RelatedWhat is the required power by WAP321 ? There's no information about IEEE 802.3af class at the datasheet.
View 1 Replies View RelatedHow can I have access to the cisco "AP#" prompt? When I try to acees the AP through hyperterminal, it gives me the attached messages. The message keeps looping and not letting me access the AP# command prompt to assign an IP address so that I can control it in mode HTTP.
View 2 Replies View RelatedI recently purchased a new Cisco 881w router (last Friday).I have configured the 'wired' part of the router with little trouble, but the wireless side is proving a little challenging.I have read a number of posts complaining about the firmware version installed on my device being very buggy.The version of the firmware on the wired part is: Version 15.0(1)M8, however, the firmware on the wireless side seems to be: Version 12.4(21a)JA1 - the version reported as buggy. The former has a version date of 2012, with the latter being 2009.I have tried to download a newer version, but the site is asking me to provide a support contract.I wouldn't mind buying a support contract if the thing worked in the first place and I was trying to add some feature after it had been working for a while.
View 1 Replies View RelatedI need some manual about how to use AIR-ACCRMK1300=.Is there any offical manual?
View 4 Replies View RelatedI am replacing a cisco linksys router with a 1941w.
I have the 0/0 accepting a DHCP from the ISP then I have 0/1 going to a switch and hosting a dhcp server.
Where I have an issue is:
A) Finding a way to turn on the wireless and make it use the same DHCP as wired and setting up a user name/wep password
B) Turning on the GUI that is supposed to be embedded on this.
C) Finding a way to make the DNS point to the default gateway so that I don't have to set the address everytime we move the box.
Here is my current configuration, and with it I can get onto the wired network and get to the internet.
Current configuration : 4712 bytes
!
! No configuration change since last restart
version 15.1
[Code]...
I have Wi-Fi on my smartphone and I want to set up another lap-top and it is asking for a security key, where do I find it ?I already have one lap-top set up !
View 1 Replies View Relatedwhere can i dwld the driver for wifi for my dell inspiron m5010, i cant use the wifi n i lost my cd drivers.
View 2 Replies View RelatedI want to start implementing a small outdoor mesh network of 3 APs Aironet 1550 in order to grow afterward with more APs. Is there any way to configure those 3 APs in an outdoor mesh configuration (for example, only one RAP and two MAPs) without a Wireless LAN Controller or I have to have at least, one WLC? My idea is to have a WLC 5508, but at the very beginning I don't know if my budget is gonna allow me to cost the WLC.
View 7 Replies View RelatedWe have implemented VSS on Cisco 6504-E switches using the 10GE links on the Sup-720-10GE. Two Cisco WLC 5508 controllers are planned to be connected in a LAG configuration, (consisting of eight links per LAG bundle) to each of the 6504-E chassis( Total of four WLC, two for primary and two for secondary). WLC HA feature may be implemented on the primary and secondary WLC controllers using the 7.3 latest code release.
View 9 Replies View Related
