I have a problem when doing Apple Airplay mirroring from my iphone5. Every time it kmocks the wifi signal off so I need to reboot the router. This is only happening on the iphone 5, and not other apple devices using mirroring. Our ipad 3 mirrors perfectly without affecting the wifi. There isn't any specific settings on the iphone 5 for airplay apart from setting it on and off.
View 2 Replies
I have 2 X E4200 router, one is directly connected to the internet and the other is in the bridge mode connected to the first router. I have apple TV connected directly with the bridge router on one of the Ethernet port.I notice that when you start apple Airplay mirroring on the iPad2 both the routers will hangs with no reason and the only way to fix it is to reboot the routers. I have reset both the routers to factory default twice they both are running firmware 1.0.03 build 14 .
View 9 Replies View RelatedI am having a trouble with using iTunes, iPhones and iPads on our Wireless LAN. We have the 2112 WLC and 10 1142N WAPs. If I do a network scan, I can see the Apple TV and see that port 5353 is open, which is Apple's Bonjour service. However, if I try to play music/video in iTunes, or on an iPhone/iPad, I do not see the Airplay icon. If I plug into the LAN, the Airplay icon appears immediately. I have created an allow all rule in the ACL but still no dice.
View 26 Replies View RelatedI've got 3 WLC 4402 controllers and the wireless is working perfectly except for 1 issue. We are trying to connect an apple tv, so we can stream picture, videos etc from ipads and Macbooks to a large display for media teaching.The setup works at home, but not at work.The apple TV is on the same network as the wireless apple devices, (we use a 10.6.4.x-10.6.5.254 range), both are dhcping the addresses (have tried fixing but that made no difference). I've enabled multicasting and igmp snooping and set the multicast address as 239.0.0.0 and it still doesn't work.
View 11 Replies View RelatedI have a Comcast modem (DPC3008) and a Cicso / Linksys E900 wireless router. I can access the Internet when I plug my computer directly to the modem. When I try and setup the router, I cannot access the Internet. The router is configured for DHCP. When I go to the status page, it lists all 0's for the IP address. I have tried releasing / renewing the IP address from the modem's home page, but no luck.
View 7 Replies View RelatedI have an issue when I use Airplay through my iPhone4S, my router reboots after 30 secs or so. I have a WRT54G2 v1.5 and the receiver is a Pioneer VSX-1021-K.
However, when I used Airplay through itunes from my laptop, it works just fine. In addition, when I borrowed my neighbors router's(BELKIN) it was working fine also. So this lead me to believe that it's my router that is causing the issue.
I've just confirmed that everytime I try to stream music from my MacBook Pro (iTunes) that is connected to my WiFi network using the 5GHz mode (channel width is Auto, channel: Auto (DFS)) to a couple Airport Express cubes are connected via the 2.4 GHz WiFi (channel width: Auto, channel: 10) the E4200 router reboots. When I set the MBP to use the 2.4 GHz mode I can stream music without causing the E4200 to reboot. The E4200 is running firmware 1.0.03.
View 9 Replies View Relatedwhat Linksys routers, e.g. WAG120N, are compatible with Airplay and Bonjour?
View 9 Replies View RelatedI have a new HP lap top which I have connected to the net thro my edimax 7266 routerI also have another lap top and desktop connected via this router. This other lap top I can connect either wired or wireless so the router seems to be working perfectlyThe problem is when I enable the HP laptop wireless adaptor and try to connect to the net . As soon as I do this the orange light on the router goes solid from blinking and I cannot then access the net from any of the computers either wired or wireless. I have to disable the HP wireless adaptor and reboot the router to get a connection on the computers.
View 1 Replies View RelatedI am facing issues with my router EA4500 and my apple TV. When I am watching a video from my itunes library at my PC, sometimes stop playing waiting to receive data. Is that a way to conect my apple tv to my router to prioritize this video streaming from my PC to apple TV?
View 9 Replies View RelatedI got an Apple TV a few weeks back and we've been using it a lot, especially to stream Netflix. However, another application that I got it for was for streaming iPhoto slideshows and iMovie stuff to the Apple TV with Airplay's screen sharing. This event scenario has played out several times..... Screen sharing is up and going and it'll be working great. All of a sudden the TV will go back to the main Apple TV menu on its own. Upon further review at this point, NONE of my WiFi (iPhone, iPad, etc.) devices will connect to the network and I have to power cycle the router. Router lights are on, but no one's home. At this point, it'll boot back up and then everything will be fine, at least for a while.Tonight, I was showing vacation pictures to some family and this same process happened twice. Since I can't seem to figure out how to stop playing a slideshow in iPhoto and then start it again in the middle, it's very annoying. Here are some relevant troubleshooting points to consider:
1. This network problem (or something similar to it) has happened in the past, but whatever it is, streaming a slideshow really seems to aggravate it. This seems to be the only scenario that I can do to actually INDUCE the issue. Periods of long uploads or downloads are fine. Streaming audio from one device and similar usage seems to be fine, but this scenario fails pretty much every time, and not necessarily right away.
2. After having this issue tonight multiple times, I stopped trying to stream an actual iPhoto slideshow and just went into the album and scrolled through the pics one by one. I did this for at least an hour with no issue. But with an actual slideshow, it failed twice in 30 minutes or less. And it's happened before tonight as well.
3. It doesn't appear to make a difference what application I'm streaming from on the Mac. Whether it's iPhoto, iMovie, or even Facetime.
-MacBook Pro Specs - OS X 10.8.2 - Late 2011 Model
-Apple TV - MD199LL/A, v5.0.2
-Router - Linksys/Cisci E1000 - Firmware v2.1.02
I've got a fair amount of devices in my home that use WiFi, but there was nothing irregular going on in the house to generate an excessive amount of internal network traffic or anything like that. My gut says the problem is with the router, but it's only a few months old, and I've updated the firmware to no avail.
A customer of ours has the following access points and wireless lan controllers on site. They want to use the Apple Bonjour service with Apple TV's and iPads. I have enabled multicast feature of the 5508 globally and one the SSID.The Apple TV has an ethernet connection and the iPads connect over the wifi. The Apple tv is on the same subnet as the iPad's - the Bonjour features do work for approx 5/10 minutes then it stops working for some reason. The Access Points plug into a Cisco 2960 Layer 2 switch, the 5508 controllers plug are in LAG mode and plug into a Nortel Layer 3 stack which I have enabled IGMP snooping.I've read that the Apple Bonjour service isnt designed to work on a multi subnet network - but both the Apple TV and iPad are connected on the same subnet. Sounds like some kind of timeout but not too sure.
View 5 Replies View Relatedhow to setup the wireless interface to forward multicast packets? Basically I cant get the ipads etc.. to see the AppleTV to control it. I connected an AP and it works fine so its got to be something with the way the router handles the packets from teh integrated wireless interface. I've been searching the forum for about 1hr and haven't founf anything other than a breif mention of broadcast forwarding and multicast setup.
View 1 Replies View RelatedI've just signed up to a local Irish Internet provider and was supplied with a Cisco router EPC3925. Wireless is working fine for laptop and iPad. However I cannot share my iTunes library with Apple TV. I connected the Ethernet cable and it worked perfectly. However as soon as I disconnect, so too does the home sharing. I've disabled windows firewall and completely uninstalled macafee firewall. Im using windows vista and have the latest version of iTunes installed.
View 1 Replies View RelatedI'm about to return my E3000 because I can't figure this problem out. As you know a new Apple TV was released and along with it you now have the capability to send music and photos from iTunes on your laptop to your Apple TV which you can then play on your TV. These two components communicate through your wireless router. However this is not happening because (I believe) that the E3000 is blocking something (a port, some rouge firewall setting, etc.). I would be happy opening every frigging port this thing has and blocking all it's internal firewalls just to see if I can get these two devices working correctly. The software that allows this to all occur is called Airplay via your homeshare g network. Any success in getting your Apple TV and your iTunes and perhaps your iPhone to call communicate together or how the E3000 works.
View 9 Replies View RelatedCan the WRT110 forward Bonjour packets? I have one WRT110 running my home wifi network with firmware version 1.0.07. I've spent hours trying to get my iPad to print to a wireless printer (HP D110a). I can print and scan from several wireless PC's on the same network but cannot see the HP printer. I started with the WEP 128-bit and then switched to WPA for a while but no luck so I switched back to WEP. I've read that other's have had similar problems with this and other Linksys routers.
From the iPad point of view I have iOS version 4.3.3. When I try to Airprint, for example through the Safari web browser, I see no printers available. I've tried many apps all with the same problem.
I recently upgraded my Linksys wrt120n router firmware & had to reconfigure settings. Subsequently, some (but not all) of my apple devices are having intermittent wireless connection problems. Specifically, my ipad1 & ipad2 never lose their connection but a mac book pro (~ 2 years old), iPhone 3g, iPhone 4, older iPod touch & very old i book g4 all work for a period of time (usually 1/2 day) & then lose their connection. When I attempt to reconnect these devices I receive the following error..."unable to join the network xxxxxx....". I also have a Dell laptop (1 1/2 yrs old) that generally does not have the connection problem. Finally, when the devices do lose their network connection all I have to do to reconnect is go to the Linkys router setup webpage & click on save & the wireless connection works again (almost like this is just refreshing the connection for these specific apple devices). I was not having any problem prior to the firmware upgrade & from what I have read the older firmware version is no longer available so going back to the old firmware does not appear to be an option.
View 1 Replies View RelatedHad an E4200 for a couple of months now and have not been able to resolve an issue with the router dropping an Apple iPad 2 at random times.The E4200 is replacing a Cisco Aironet 1200, which never dropped any clients, iPad 2 or others, and never displayed any of the issues below.
TECH DETAILS:The E4200 is being used purely as an access point. All extras are not in use and are disabled.
Firmware 1.0.03
Hardware version 1.
BASIC ISSUE:The E4200 drops an Apple iPad 2 off the 2.4 Ghz Mixed (B, G, N) network. The user must then select the network to rejoin. Rejoining occurs without incident. The same issue occurs when the network is restricted to B, G. The drops occur at what appears to be random intervals - sometimes 10 minutes apart, sometimes hours apart. We can have as many as 6 drops in an hour. A ping to the apple ipad shows the device stops responding to pings about 10 seconds before the user is prompted to rejoin a network. Meanwhile, a ping to the E4200 itself from a laptop connected via the E4200 on the same radio as the ipad continues to work without fail during this incident.
1. The iPad 2's cannot connect to the 5Ghz radio. I believe iPad 2's are supposed to support 5Ghz.
2. Both our Apple TVs do not connect to the 5Ghz radio: they fail with a "There was an error connecting to the network. Check your settings and try again. (-3914)" error. Apple TV supports 5Ghz.
3. The admin interface for the E4200 is very slow sometimes. Probably over 20 seconds to render some pages when it gets really bad. As a comparison, Internet-based pages on fast sites that delivered via the E4200 itself load in less than 2 seconds.
4. The HTTPS version of the admin interface can only be connected to via Safari browers. Both Internet Explorer 9 and Chrome 16 fail to connect with a "Connection reset" error. In Chome, it says "Error 101 (net::ERR_CONNECTION_RESET): The connection was reset." This is across multiple devices. There is no issue with straight HTTP.
All other devices - including Macs and PCs - connect fine with the E4200 on both 5Ghz and 2.4 Ghz radios, even if they cannot access its admin interface via HTTPS.I've presented quite a few issues above, but the main one is the drop outs for the iPad 2 devices. I'd present logs on drops, but the thing doesn't record any useful logs.
Basic wireless config:
5Ghz:
Network Mode: Wireless-N Only
Channel width: Auto (20 or 40 Mhz)
Channel: Auto (DFS)
SSID Broadcast: Enabled
[URL]
I've recently purchased an E4200, and while it works great, I'd like to use my Apple Airport Extreme (2nd generation) to extend my network to another part of the house that doesn't get as great of a signal. I've become very frustrated trying to accomplish it, and I'm not sure if the problem is more from the Linksys end, the Airport end, or if it's just me.
View 3 Replies View RelatedI try to connect my LinkSys wrt320n with Apple Time Capsule with mode "sahring existing wireless network" and so Time capsule doesn't work. It gets IP, but writes "isn't internet connection, WiFi network don't find" and also in the admipage of my wrt320 I can't see Time Capsule as client.
View 4 Replies View RelatedI am using a EA4500 and use Linksys Smart Wi-Fi to manage the device. In the household we have multiple Apple i devices. Somehow the Linksys Smart Wi-Fi combined two separte i devices (iPhone 5 and a 4th generation iTouch) to one user.The devices actually have different names, but the Smart Wi-Fi is combining them into one device. So I can't use Parental Controls on one of the devices.
View 8 Replies View RelatedIs it possible to configure the apple airport express to extend a linksys wrt120N wireless network? if so how?
View 2 Replies View RelatedI'm currently setting the MAC address filtering for my Linksys E2500 router. I have about 20 devices which i'm allowing to access my router, so i keyed in the MAC addresses into the config page and save setting. But only 16 addresses are registered, the rest refused to register no matter how many times i key in, it just reset back to 00:00:00:00:00:00 after i click on save setting.
View 4 Replies View RelatedI previously entered in settings for the "Static DNS" 1 through 3 (using ip addresses from OpenDNS and one from Google DNS).
I want to remove these so the router reverts to using the DNS allocated to it by the ADSL modem (which will likely be the IP of the modem, which then forwards the requests to the DNS from the ISP).But I can't clear the Static DNS settings. I have to put in 0.0.0.0 but the last zero is not accessed. I get the error: The value is out of range [1 - 254].So I end up with 0.0.0.1 and then all Internet access is lost on the computers because they are being given a bad DNS IP.
How can I reset the static DNS ip address back to 0.0.0.0 ?
I am trying to connect to a new VPN using my E2500 router. As soon as I connect, the connection breaks.
View 1 Replies View Relatedi buy a new e2500 from staples. but when i try to register the product. it shows me "Serial Number you entered is invalid.". i am sure i choose the right product and number to register.. so is that mean some one used it..
View 3 Replies View RelatedI want to add my E2500 as a second wireless router to cover my entire house.I have a Motorola Surfboard SBG6580 cable modem (Time-Warner) at one end of the house.I added via powerline Ethernet connection a new E2500 wireless router at the other end of the house.The E2500 set-up with all defaults and has the same SSID and Password as the Surfboard cable modem.It seems to work OK, but I wonder about network confusion/interference.Do I have to configure the E2500 in some manner to allow seamless roaming of my wireless devices (iPad, Cell Phones, Netbook)?I had an RE1000 with just the Surfboard, but it did not quite do the trick, and does not like both routers connected at either end.
View 9 Replies View RelatedHow To Reset E2500 Router
View 1 Replies View RelatedI am trying to setup a WAP with my linksys 2500. I am currently using a Gateway connected to my DSL and am looking to set up the access point through the E2500.
View 1 Replies View RelatedSo, i have a e2500 router and find that every so often, I have to unplug it and reset it because I am losing my internet connection.
View 7 Replies View RelatedHow to set router to use as Slind Box Pro?
View 3 Replies View RelatedI currently have my E2500 connected via wired LAN (not WAN) port on another router. The E2500 has an LAN IP of 10.0.0.2 and the router has 10.0.0.1 and a dhcp range outside of these. DHCP is disabled on the E2500. I can use my E2500 as a wired access point with no difficulty I plug something in and it calls the router and gets an address, but I can not get DHCP through the wireless of the E2500.
View 2 Replies View RelatedI have Time Warner as my internet company. I recently purchased a new Linksys Router Mode E2500 because I have been having issues with my old router. My internet was disconnecting sporadically. After connecting the new router, a started getting the same issue. I replaced my internet cable modem to a Cisco 2100 modem (provided by Time Warner). I noticed that the issue keeps happening sporadically which makes me believe it is my Linksys router. Every time a new wireless connection is connected, my modem circuit dies. This happens sporadically.
View 4 Replies View Related
