I try to connect my LinkSys wrt320n with Apple Time Capsule with mode "sahring existing wireless network" and so Time capsule doesn't work. It gets IP, but writes "isn't internet connection, WiFi network don't find" and also in the admipage of my wrt320 I can't see Time Capsule as client.
View 4 RepliesI've brought a SG300-10 switch and would like to connect it to an Apple Time Capsule (as the base station of my wireless network), Apple Airport Extreme (to extend my wireless network) and 3 x NAS. What is the best way to connect?
Internet > SG300 > Apple TC + NAS x 4 + Apple Airport Extreme (to extended my wireless network) + Mac Pro/iMac'sInternet > Apple TC > SG300 > NAS x 4 (connect to the SG300) + Apple Airport Extreme (to extended my wireless network) + Mac Pro/iMac'sI need the SG300 because the Apple TC doesn't have enough network ports to cennect all my other devices.
Briefly here is my setup Internet is supplied to my building by ISP(I have no router) => apple time capsule connected by Ethernet.I have used WIFI to connect all of my devices in the past with no problem until i moved into this place. I have 2 macbooks that can connect without any issues Every single other device in the house cannot connect and does not receive a proper IP Address. The ones being assigned are in the 169.xxxxxx range. Even if i plug my Imac (which cant connect) directly in from the wall via ethernet, it wont connect.The time capsule is setup as a bridge with DCHP set to run automatically. I have reset everything numerous times and restored the router to no avail.I called the ISP and they said it wasnt their problem. I was under the impression they werent assigning the IP Address correctly or something.
View 1 Replies View RelatedI'm looking to buy an EA3500. I want to hook an external drive to the USB port and use it as a Time Capsule drive with Mountain Lion. Is this supported?
View 5 Replies View RelatedI've just signed up to a local Irish Internet provider and was supplied with a Cisco router EPC3925. Wireless is working fine for laptop and iPad. However I cannot share my iTunes library with Apple TV. I connected the Ethernet cable and it worked perfectly. However as soon as I disconnect, so too does the home sharing. I've disabled windows firewall and completely uninstalled macafee firewall. Im using windows vista and have the latest version of iTunes installed.
View 1 Replies View Relatedtime capsule can be the same as the router settings?
View 1 Replies View RelatedAt home I have been trying to set up this Time Capsule as a Router. url...I am trying to set this up for both Macs and PCs. I have set it up as described in the manual and can now find it on all machines in the house and can connect to it wirelessly. I an also plug it into a desktop and get the same issues. So its not a wireless issue.The issue is here. The computers can get email, POP i believe, but no internet.I cannot ping anywhere, and have tried browsing by names, and IPs to no avail. When I ping google.com it says could not find the url.... Ive also tried Telnet. I tried Telnetting the router IP on port 80 however could not figure out what the IP is. I was looking for the 192.168 etc.
View 5 Replies View RelatedHow do I disable the wireless?
View 9 Replies View RelatedI no longer have a software disc, but setup via the 192.168.1.1 page has worked out fine...until the last reset. After the last reset/reboot of the wifi, I was unable to set up the wifi beyond use with my laptop. This is, no doubt, user error.WRT320N.No hard wire, wifi is connected to the cable modem. Everything in the house was on the wireless.
Issue: Laptop finds and connects to wifi just fine, password works just fine.iPhone cannot even detect the wifi in the house (but finds every other wifi in the neighborhood)iPad cannot detect the wifi in the house (but finds every other wifi in the neighborhood)Desktop cannot detect the wifi in the house (but finds every other wifi in the neighborhood)What do I need to tweek in the admin page 192.168.1.1 to allow other computers to jack into my wifi?
is it possible to setup a wired local area network using time capsule 2T as the router?
View 1 Replies View RelatedI have had my router for at approx. a year and a half and it has worked flawlessly. Now my PC which is plugged into the router still works fine, I'm just not able to connect wirelessly anymore. I've tried the basic things like unplugging and rebooting, nothing changes. The lights still say it is transmitting.
View 1 Replies View Relateda colleague at my university is using an Airport Time Capsule 1TB (Model A1355) to share files with his students wirelessly. The machines are running Leopard 10.5.8 and It works well but it will only allow 20 wireless clients at a time. All the client machines log in with a password. When you remove one of the 20, another can log in.
The tech specs on the Apple website just say that it accepts Wireless guest access and there is no mention of a 20 client limit. I looked right through Airport Utility and couldn't find where the number of wireless clients could be configured.Does anybody know if this is the hard limit for the number of wireless clients for an Airport Time Capsule 1TB (Model A1355)? If it is not a hard limit does anybody know how to change it?
I have WRT54G2 router. All settings are more-less default and the behavior is following.You start up the router. If you do not connect wireless device within 10 minutes, then you have to restart the router.You have assigned IP via wifi, and when you connect cable device to the router, the wifi PCs are disconnected.
View 3 Replies View RelatedHow do I set up my iPad2 to use my home WiFi using WRT320N Cicsco router?
View 9 Replies View RelatedI have experienced some strange behavior of WiFi connection using WRT320N router. ISP provides me the internet in 2 modes (day and night). During day mode max speed is 24 Mb/s and during night 60 MB/s. Modem ADSL (Cisco EPC3010) is connected to Linksys WRT320N and on router is configured WiFi.Now issue. In the day mode everything is perfect. Cable connection gives me 24 MB/s and WiFi connection around 22 MB/s so not so bad. However when my internet speeds up to 60 Mb/s (cable connection via router gives exactly 60), WiFi connection instead speed up as well, just drop to max 17 Mb/s. I have tied several different settings on the router including changes in WiFi band, channel width, different channels (now channel is setup to 1 which is maybe not totally free but no so occupied) and others but unfortunately without significant improvement (in many cases connection just slowed down more).
And some details:
Wireless configuration (now)
Band: 2.4GHz
Mode: Wireless-N only
Channel Width: Auto (20MHz or 40 MHz)
Channel: 1
Wireless adaptor: Intel Centrino Advanced-N 6230 (I know that this doesn’t mean anything but Win7 shows that connection is established with speed 144MB/s)Router firmware and WiFi card updated to the newest version.
I live in a new apartment building which means a lot of concrete. The internet (fiber) enters the house at the beginning where the modem is hooked up to my Linksys WRT320N. From there two cables run through the house:1 to the home office, where two computers are connected through a switch.1 to the living room, where the Xbox, blue-ray player are connected through a switch.I also have a wifi network running from my WRT320N, but as it is at the beginning of the house, there are some black spots in other parts of the house. I tried to fix this with a Netgear repeater, but that keeps disconnecting.
What I want to do know is place a second linksys device in the living room at the end of the already existing cable that will also broadcast a wifi network, but I want this to be exactly the same Wi-Fi network as I already have. What I want to achieve is that I can walk from one end of the house with my iPad, streaming a video, to the other end of the house and that I always stay connected to the internet and that my tabled just picks up the strongest broadcaster, basically the same as with a mobile phone.
I am using a EA4500 and use Linksys Smart Wi-Fi to manage the device. In the household we have multiple Apple i devices. Somehow the Linksys Smart Wi-Fi combined two separte i devices (iPhone 5 and a 4th generation iTouch) to one user.The devices actually have different names, but the Smart Wi-Fi is combining them into one device. So I can't use Parental Controls on one of the devices.
View 8 Replies View RelatedI have set up a home network with Time Capsule as the primary router. I would like to use my WRTG54GL to connect to the network via ethernet and extend it for wireless access at the opposite end of my house. I changed the settings to disable the DHCP server, I named the network the same as the Time Capsule and duplicated security mode and password. I can connect with my laptop, but it initially connects with full internet access, but after about 10 seconds, I can see Airport searching for a network. It reconnects, but for about 45 seconds I have no internet access and then access returns and works fine. On my iPad, however, although it shows I am connected to the network, there is no signal indicator at the top of the screen, and all connectivity seems to be through 3G -- not the network. I assume there is a setting on the Linksys that needs changing, but I can't figure out what it is.
View 10 Replies View RelatedI have a Time Capsule current generation, as my primary router connected to my ISP. I'm using a Linksys E4200 as my slave router connected to the Time Capsule via lan to lan. I noticed the TC Internet Connection TCP/IP via DHCP shows a Subnet Mask of 255.255.248.0 and the Surewest IP of 74.222.246.23
Is the 248 setting one I will need on the slave?
The TC IP Address is 10.0.1.1 the DHCP Beginning Address is 10.0.1.3 to allow for the slave to have 10.0.1.2.
The E4200 is set as follows on the routers setup page, Internet Section to Automatic DHCP, Network Section to IP 10.0.1.2 Subnet Mask 255.255.255.0 and DHCP is Disabled.
Both routers have a SSID set to the same name.
Are all these settings correct? I've noticed that a device iPhone or iPad etc has a different IP address assigned by the TC depending on which router it is actually connected. I've also noticed difficulty of a device on one router communicating with one on the other.
I have 3 computers, all Macs. Two are hooked into my WRT54GP2 via ethernet cables, and one is using WiFi (Airport Extreme). All get an IP number from the router via DCHP (no hard numbers). The router is also hooked up to a Motorola Surfboard cable modem.The two Macs using ethernet have no problems at all, and can access the internet and share files and printers. The WiFi Mac, however, can access the Internet fine, but cannot mount the other machines as file servers. It doesn't even ping them. What is going on in the setup of the router that is preventing the ethernet machines from being seen properly by the WiFi Mac?
View 6 Replies View RelatedSet up a Smart Wi-Fi yesterday. Linksys Smart Wi-Fi Router N600. Have 2 computers side by side. Connected my computer seamlessly. Works perfect. Went to set up my husbands computer (both computer are desk top HP Pavillion running windows 7) and the way I was doing it thru the network sharing center on his computer I was not able to get the computer to see the wi-fi. I tried both the router p/w and the p/w that was supplied by the smart wi-fi help center. So I wired it directly to the Linksys router with a new cat-5 ethernet cable. VOILA..internet connection! Question..is his computer secure even tho it doesn't have it's own p/w and is wired directly to the router? My thought is "yes" since the router is p/w protected.
View 8 Replies View RelatedI am trying to set up WRT on my WRT320N access point so I can connect it to my other access point that also doubles as my DSL router.Where can I find the WDS on the WRT320N?
View 1 Replies View RelatedI have a WRT320N, firmware version 1.0.05., Windows 7 Home Premium SP1, and a Hewlett Packard laptop.I would like to utilize both bands on my router at the same time for internet access, so that I can have the one my kids use shut down at a certain time but mine stay up.If not, what's the closest I can get, even if I have to purchase additional items to do so? Do I have to manually turn their band off when I want it off? And can I even have both bands in use at the same time?
I looked at my Cisco online info by access the IP address. I see the Access Restrictions tab. Can I even set usage by specific computer? If so how do I do that?
After playing around I cannot get the router to get into the wide 40 MHz mode any more (2.4 GHz)
View 5 Replies View RelatedI've purchased this router a few weeks ago, but I can't use it as I can't get on the internet with it plus my laptop which as wifi will not recognize it.
I would really like get it going, I've tried live chat but I guess the techy didn't have the patience, I am a slow typer for lack of a better word.
Just installed linksys wrt320n. Desktop and one laptop (wireless) connect. Both windows 7. A second laptop (Vista) errors out with message "the selected data rate is not correct". This laptop sees the router (since I see the router name and it validates the passphrase) but I cannot ping the router. I saw two messages on this site suggesting to enable WMM and use security WPA2. I have verified that both of these are so set.
View 9 Replies View RelatedI'm currently using my WRT320N router as an access point (connected to another linksys router), but I've lost my username and password to access the web-based utility. So I need to press the reset button and set it up again. Currently everything is working fine, but I've forgotten how to configure the router for this purpose, and I can't find instructions in the user's guide online. I seem to remember it being troublesome. I know I have to assign a different IP address (currently I'm using 192.168.1.113.) What other settings (if any) need to be changed?
View 2 Replies View RelatedI want to setup the following:
Internet through DSL-Thompson TG 789 VN router ---> several yards --> Linksys WRT320N --> wired computer netwerk | |with printer
| |
---> Wireless Netwerk --> laptops / phones <--- (WAN depending on strongest signal)
|
---> several servers
The Thompson does the DHCP and routing. It is the gateway through the internet, IP 192.168.2.254 (mask 255.255.255.0).I can't replace the thompson since it is delivered by my provider. SSID = BertB I want to achieve that all the compuers / laptops / phone and printer are in one network and can communicate with each other So the only possibility, as far as I can see, is to set up the Linksys as a bridge.
I have to do the following at the Linksys but have some questions as mentioned below:
SSID = BertB (the same)
channel = different from the channel used by Thompson
DHCP = off
IP = fixed (192.168.2.253)
gateway = 192.168.2.254
[code]....
how the thompson and the Linksys will build a connection with each other, or will this happen automatically through the above setup?Do I have to put the mac address of the thompson in the Linksys and/or vice versa?
I just bought a Linksys 320N router to replace another competitors router. I am trying to connect to my VPN server from outside my network. I have the external ip to my network. I setup the new 320N router just like the old router. set dmz ip to internal ip of vpn server, set port forwarding to 1723, both, internal ip of vpn server, I have a way to test the vpn while i am inside my network. So, I can watch the VPN server log and see the request come into the server and it times out with the Linksys 320 N hooked up. If I have the old router hooked up, the vpn establishes a connection.
View 9 Replies View RelatedI have a WRT320N router with firmware version 1.0.01 build 008. I just got an iPad and while it can find my router, I can't access the WiFi when I enter my password. I can use the router with my laptop so I know the connection and password are ok.I've seen two administrators on here suggest the same thing. And one person responded that it worked. The identical directions were:
Try changing some advanced wireless settings on the router.Connect the computer to the router with the Ethernet cable. Open the setup page of the router.Click on wireless tab and set the configuration view to manual. Change the wireless channel to 11. Save the settings.Go to wireless tab and click on Advanced wireless settings.Change Beacon interval to 75, RTS threshold to 2307 and fragmentation threshold to 2306. Save the settings.Try to connect to the wireless network again and see if that works.
1 - I think my computer already is connected to the router with the Ethernet cable - I mean there is an Ethernet cable attached to both my computer and my router - in slot 1 on the router
2 - the only thing I know how to access is the Linksys EasyLink Advisor. What and where is the setup page of the router?
I am running a WRT320N with Firmware 1.0.04Trying to Upgrade the Firmware to 1.0.05 it always fails at about 24% progress with a message saying an invalid value has been entered.I downloaded the firmware from your homepage twice so that the file is not corrupted
View 4 Replies View RelatedI have some major problem with my WRT320 router. For some reasonit won't let me connect to Age of Empires 2 (other, newer games work fine) via Hamachi. When i want to connect i can see the game but when i want to join it tries to connect but fails telling me i'm unable to join... I know the problem is in the router because when I connect my modem directly to my computer Age of Empires connects fine!
View 8 Replies View RelatedWe have WRT320N (Model No.) and when I moved i notice that my wirelss network does not have internet connection. Even after I hook everything up it doesn't work, my computer does not recognize the network but the laptop does. I have prior knowledge about computers and the internet but I don't know why I am having a problem. Is it because I moved and the data in my previous home does not match the data here?
View 3 Replies View Related