Linksys Wired Router :: Setup A SG300-10 With An Apple Time Capsule
Dec 2, 2011
I've brought a SG300-10 switch and would like to connect it to an Apple Time Capsule (as the base station of my wireless network), Apple Airport Extreme (to extend my wireless network) and 3 x NAS. What is the best way to connect?
Internet > SG300 > Apple TC + NAS x 4 + Apple Airport Extreme (to extended my wireless network) + Mac Pro/iMac'sInternet > Apple TC > SG300 > NAS x 4 (connect to the SG300) + Apple Airport Extreme (to extended my wireless network) + Mac Pro/iMac'sI need the SG300 because the Apple TC doesn't have enough network ports to cennect all my other devices.
View 1 Replies
ADVERTISEMENT
Aug 17, 2012
I try to connect my LinkSys wrt320n with Apple Time Capsule with mode "sahring existing wireless network" and so Time capsule doesn't work. It gets IP, but writes "isn't internet connection, WiFi network don't find" and also in the admipage of my wrt320 I can't see Time Capsule as client.
View 4 Replies
View Related
Jan 5, 2013
is it possible to setup a wired local area network using time capsule 2T as the router?
View 1 Replies
View Related
Jan 6, 2012
Briefly here is my setup Internet is supplied to my building by ISP(I have no router) => apple time capsule connected by Ethernet.I have used WIFI to connect all of my devices in the past with no problem until i moved into this place. I have 2 macbooks that can connect without any issues Every single other device in the house cannot connect and does not receive a proper IP Address. The ones being assigned are in the 169.xxxxxx range. Even if i plug my Imac (which cant connect) directly in from the wall via ethernet, it wont connect.The time capsule is setup as a bridge with DCHP set to run automatically. I have reset everything numerous times and restored the router to no avail.I called the ISP and they said it wasnt their problem. I was under the impression they werent assigning the IP Address correctly or something.
View 1 Replies
View Related
Aug 15, 2012
I'm looking to buy an EA3500. I want to hook an external drive to the USB port and use it as a Time Capsule drive with Mountain Lion. Is this supported?
View 5 Replies
View Related
Apr 24, 2012
time capsule can be the same as the router settings?
View 1 Replies
View Related
Aug 5, 2011
At home I have been trying to set up this Time Capsule as a Router. url...I am trying to set this up for both Macs and PCs. I have set it up as described in the manual and can now find it on all machines in the house and can connect to it wirelessly. I an also plug it into a desktop and get the same issues. So its not a wireless issue.The issue is here. The computers can get email, POP i believe, but no internet.I cannot ping anywhere, and have tried browsing by names, and IPs to no avail. When I ping google.com it says could not find the url.... Ive also tried Telnet. I tried Telnetting the router IP on port 80 however could not figure out what the IP is. I was looking for the 192.168 etc.
View 5 Replies
View Related
May 15, 2013
how to setup the wireless interface to forward multicast packets? Basically I cant get the ipads etc.. to see the AppleTV to control it. I connected an AP and it works fine so its got to be something with the way the router handles the packets from teh integrated wireless interface. I've been searching the forum for about 1hr and haven't founf anything other than a breif mention of broadcast forwarding and multicast setup.
View 1 Replies
View Related
Jan 29, 2011
I have set up a home network with Time Capsule as the primary router. I would like to use my WRTG54GL to connect to the network via ethernet and extend it for wireless access at the opposite end of my house. I changed the settings to disable the DHCP server, I named the network the same as the Time Capsule and duplicated security mode and password. I can connect with my laptop, but it initially connects with full internet access, but after about 10 seconds, I can see Airport searching for a network. It reconnects, but for about 45 seconds I have no internet access and then access returns and works fine. On my iPad, however, although it shows I am connected to the network, there is no signal indicator at the top of the screen, and all connectivity seems to be through 3G -- not the network. I assume there is a setting on the Linksys that needs changing, but I can't figure out what it is.
View 10 Replies
View Related
Feb 11, 2011
a colleague at my university is using an Airport Time Capsule 1TB (Model A1355) to share files with his students wirelessly. The machines are running Leopard 10.5.8 and It works well but it will only allow 20 wireless clients at a time. All the client machines log in with a password. When you remove one of the 20, another can log in.
The tech specs on the Apple website just say that it accepts Wireless guest access and there is no mention of a 20 client limit. I looked right through Airport Utility and couldn't find where the number of wireless clients could be configured.Does anybody know if this is the hard limit for the number of wireless clients for an Airport Time Capsule 1TB (Model A1355)? If it is not a hard limit does anybody know how to change it?
View 3 Replies
View Related
Mar 14, 2012
I have a Time Capsule current generation, as my primary router connected to my ISP. I'm using a Linksys E4200 as my slave router connected to the Time Capsule via lan to lan. I noticed the TC Internet Connection TCP/IP via DHCP shows a Subnet Mask of 255.255.248.0 and the Surewest IP of 74.222.246.23
Is the 248 setting one I will need on the slave?
The TC IP Address is 10.0.1.1 the DHCP Beginning Address is 10.0.1.3 to allow for the slave to have 10.0.1.2.
The E4200 is set as follows on the routers setup page, Internet Section to Automatic DHCP, Network Section to IP 10.0.1.2 Subnet Mask 255.255.255.0 and DHCP is Disabled.
Both routers have a SSID set to the same name.
Are all these settings correct? I've noticed that a device iPhone or iPad etc has a different IP address assigned by the TC depending on which router it is actually connected. I've also noticed difficulty of a device on one router communicating with one on the other.
View 1 Replies
View Related
Jun 26, 2011
On the BEFSR41 v1 series and WRT54G series, what is the maximum value for the DHCP "Client Lease Time (in minutes)?" It seems that 2^16 -1 (65535) minutes is the max. This is about 45 days. has the max value changed with newer versions of these devices?
View 1 Replies
View Related
Jan 24, 2013
We share a common fibre connection to the internet. In the basement we have a modem/router(zyxel) which is in "bridge mode". Therefore not acting as DHCP.Behind this zyxel we have a Cisco RVS4000 router. Ports 1 and 2 go to family A, and Ports 3 and 4 go to family B.Family A and B have separate routers which are both set to "access point mode". Family A has an ASUS RT-N66U router while family B has a dlink DIR-615. The asus has an "access point mode" while the dlink needs to be set up manually to achieve this. The dlink must also have a static IP adress. The asus can receive ip adress.
View 1 Replies
View Related
Mar 16, 2011
We have a Network set up with a RV042 router. Router is hooked up to Cox Cable and ATT DSL. Currently have 20 computers hooked up to the router all using Static IP addresses. Setup has been in place for over 7 years. I want to set up a Wireless Access point on this network. The problem is, I can't seem to get DHCP to work right even WITHOUT the Wireless Access Point. I have taken one of the computers that works great with a static IP and changed it to be DHCP, I have enabled DHCP on the router and set the from and thru parameters for the IP assignment. The computer will connect and get an IP address and it allows me to see all the INTERNAL servers on the network but going to the Internet is REAL FLAKY. I usually have to refresh 5 or 6 times to get a web page and sometimes even that don't work. If I do get a page to come up there is about a 10% chance that it will bring up a subpage of that page without doing a refresh 5 or 6 times. Its like it won't hold the connection to the Internet. I did notice one thing different in the User Manual of the RV042 that is different than all the other Linksys routers I have worked with. It says that when you enable the DHCP on the router, you then make sure ALL computers hooked to it are set for DHCP. All other routers I have worked with do NOT use that word ALL. Am I missing some setting or is this a binding thing where you are either ALL static or ALL DHCP?
View 1 Replies
View Related
Dec 19, 2012
How to setup the quickvpn.... I am getting the message Servers certificate doesnt exist on your local computer..... and the the window fail to establish the connection
View 1 Replies
View Related
May 1, 2012
I'm trying to setup 2 subnet with two RV042 routers. One router will act as a gateway and both WAN ports will be used by two different isp connection. The first router (gateway) LAN IP will be 192.168.0.1/24.I would also like to set up another router behind the gateway with with separate subnet 192.168.1.X/24. And I would like clients on the 192.168.1.x subnet to use the internet through the gateway router and clients on the 192.168.0.x subnet to access resources on the 192.168.1.x subnet. Am I able to do this with two RV042?
View 1 Replies
View Related
Nov 24, 2009
I have a RV042 router and we are trying to set-up our OWA for outside access. I can't figure out which ports or which page those ports are on to open them. We are a small company and we do not have IT except for ourselves. The internal network works fine but i can't get the Exchange access from outside.
View 2 Replies
View Related
May 21, 2011
Currently, I have 2 Apple Airport Extremes, and 1 Wireless Netgear ADSL Router. The 2 AAEs are connected separately to the router, and this allows us to get coverage in most part of the house (it's a large house with concrete and granite walls). I also have a HP Officejet 8500 'wireless printer' that is wired to the router as you can only print to the printer when it's in standby with a physical connection to the router (that's a different story). So my goal is to replace everything as the router is slowly dying and as a result of this, I want to be able to access the Internet wirelessly throughout the house, and be able to print from any where in the house without anything connected via cables. And as a bonus, I would like the Internet to be accessible 100 yards/metres down the garden (workshop is there). Basically, blanket coverage!
View 3 Replies
View Related
Nov 5, 2009
I have two PCs hooked up to the same router, a BEFSR41. Both connect to the internet fine. One can access the router setup/admin page fine. On the other one, though, the router asks for a user name and p/w, but the setup screen never loads. I get the eternal "Loading" message but it never gets there.
[code]....
View 8 Replies
View Related
Feb 23, 2011
I'm trying to setup a VPN Tunnel between RV082 and WRV200.The RV082 has an static IP, the WRV200 has a dynamic IP. I have to Dyndns.org in the WRV200.I have setup the RV082 tunel auth like: Dynamic IP + email.In the WRV200 I setup the hostname with the username, and the domain with the domain part of domain entered in the RV082.In the RV082 VPN Log I got: Initial Aggressive Mode message from 11.22.33.44 but no (wildcard) connection has been configured.It seems to be working the IPSEC setup but the RV082 does not accept the connection because of a missmatch in the Remote Security Gateway Type parameter in the RV082.
View 1 Replies
View Related
Sep 1, 2011
On a BEFVP41, I disabled snmp for testing (because it was sending some strange alarms), and now I can't login to the web setup pages. The username and password no longer work. I thought maybe it reset itself to default (blank/admin) but it didn't.
View 1 Replies
View Related
Jan 22, 2013
Recently lost the setup for my newly installed ea6500 for no apparent reason. had to restart from the ground.I have the latest upgrade but wonder about the differences between the linksys coonect to the online version vs stand along versions. DO nor like expensive software that losses its setup for no good reason.I also irritated that I am unable to access my cable box. I own it and cable box and lynkiys has no right to block me from it. 192.168.100.1. I was able to accessed it with my Belkin router and I should be able to access with this expensive ea6500 box!!
We NEED a non-gui version. The gui is great for simple networks and people who do not want to know anything about their network. it's ment to be use to deliver additional services to us at a cost. duplicated or generates random users with ip or mac addresses complicating the parental control.
View 1 Replies
View Related
Aug 11, 2011
I have just setup a E2000 at home. All the wireless connections work and also my NAS server who i wired. But when i try to setup my wired media server it will not connect.
View 6 Replies
View Related
Jan 10, 2012
I have the Linksys BEFSX41 wired Firewall router. My ISP is Verizon DSL. The DSL modem is a Westell 6100G. I have the wall phone line connected to my modem. The output of the modem is going to the input of my Linksys router. I have two computers connected to the router outputs. In order for me to see the output or configuration of my Westall modem, I have to go http://192.168.1.1. In order for me to see the configuration of my Linksys router, I have to enter http://10.10.10.1. When I look at the instructions for setting up and configuring my Linksys router, it never mentions the above 10.10.10.1 address, but instead it tells me to enter the 192.168.1.1 address. I have never done this because when I powered both units for the first time, and it worked, I noticed then that my Linksys address was the 10.10.10.1. Why is it then that none of the settings or instructions for the Linksys router never mention to enter the 10.10.10.1 address as oppose to the one the do call out to enter which is the address for the Westell modem? What would happen if both addresses on both devices were the same?
View 2 Replies
View Related
Feb 7, 2013
I am having issues figuring out how i can make AppleTV,Airprint, Airplay, etc show up on Ipads that are connected to the wireless network. The controller is at a main site which is seperated by 2800 series routers at the remote sites over 100Mbs links. Ipads connect and tunnell back to the main site. I've tried enabling FlexConnect but the devices still get the main site's addressing so i'm guessing they are still tunneling unless the AP loses connectivity to the controller. I have two SSIDs (staff and students). I have tested with just setting the staff to FlexConnect. Do I need to set both SSIDs to FlexConnect to make them dump data locally? AppleTVs are connected wired to the local networks and get addressing associated with that building.
View 8 Replies
View Related
Apr 10, 2012
I have to put cd in and run setup every time I want to get online. WHY
View 2 Replies
View Related
Oct 26, 2011
I have WRT54G2 router. All settings are more-less default and the behavior is following.You start up the router. If you do not connect wireless device within 10 minutes, then you have to restart the router.You have assigned IP via wifi, and when you connect cable device to the router, the wifi PCs are disconnected.
View 3 Replies
View Related
Nov 7, 2011
I finally decided to go with a e3200 yesterday and picked up one at Walmart. Last night I went to hook it up and had no luck setting it up. Now I have able Internet with a phone VoIP service. After trying to connect several ways, all the router wants to do is sit with a flashing power light. I cannot access the setup page wireless or wired and have tried several methods I found last night.
View 1 Replies
View Related
Apr 6, 2013
i am trying to setup a vpn Gateway To Gateway when i setup the vpn i can ping the 2 rv042 i cant see any computer in the network places when there comect we need to see the computer in the network places so are pos will run?
View 1 Replies
View Related
Aug 13, 2011
I just received a new Cisco SG300-10 and am configuring it in Layer 3 mode. I am trying to setup multiple routed VLANs going back to a FiOS Actiontec router. My configuration is as follows.
Fios Router: 192.168.1.1
Assigning DHCP 192.168.1.2 through 100.
SG300-10 has VLan 1 ip 192.168.1.5 used for Mgmt.
VLAN2 is 10.0.2.1
VLAN3 is 10.0.3.1.
I have a static route set on the fios router for both subnets setup as follows.
Destination 10.0.3.0 Gateway 192.168.1.5 Netmask 255.255.255.0 Metric 1
Destination 10.0.2.0 Gateway 192.168.1.5 Netmask 255.255.255.0 Metric 1
I have a laptop connected to Gi8 on the Cisco (Vlan 3) and statically assigned 10.0.3.3, with a gateway of 10.0.3.1. DNS set to the fios router (192.168.1.1).
Everything pretty much works EXCEPT, I cannot get out to the internet from either vlan. Traffic routes between vlans/and the default subnet on the fios without issue.
When I ping out, DNS resolves, but will not go past the fios router. Am I missing a setting somewhere?
View 3 Replies
View Related
Jan 27, 2011
I am trying to set up a d-link router with a modem provided by time warner cable. I've powered down, reset the router, and I've put it on dynamic settings (sorry if that's incorrect terminology... not a comp. buff). I can't get my wireless to connect to internet.
View 1 Replies
View Related
Jun 20, 2012
I've just installed an SG300-28 (v01) switch configured in layer 3 mode with 1.0.0.27 firmware. It's working just fine except that when running a traceroute across the switch, it does not respond with an ICMP-11 time exceeded packet. Does this behavior persist in the current 1.2.5 firmware?
View 1 Replies
View Related
May 3, 2012
I’m having issues with enabling Apple’s AirPlay services on a relatively simple network consisting of a Cisco 881 (Advanced IP Services) and an autonomous Cisco 1142 AP. I’ve attached a diagram explaining the connectivity. I believe I have to enable IP Multicast at the router, but I’m not really sure the best/right way to do it. Also I’m not sure what/if any commands would be needed at the AP.All of the wireless clients are confirmed to be in the same subnet, so no real routing is happening etc. Also regular Internet connectivity/routing from the wireless clients is fine.
View 5 Replies
View Related
