Cisco Switching/Routing :: VISIO Icon For WS-X45-SUP7-E And 4507R+E?
Mar 21, 2011I´m looking for the VISIO icon for WS-X45-SUP7-E and 4507R+E.
View 13 Replies
ADVERTISEMENT
Cisco Switching/Routing :: Difference Between WS-X45-SUP7-E/2 And WS-X45-SUP7-E
Nov 7, 2011I see there are two different part numbers for Sup7-E. One has /2 at the end. So what's the difference between them?
View 2 Replies View RelatedCisco Switching/Routing :: Get Visio Stencil For C3KX-NM-1G Module
Dec 19, 2012I was trying to get a visio stencil for C3KX-NM-1G module but it doesn't seem to exist. It indeed does not exists or I just can't find it.
View 2 Replies View RelatedCisco Switching/Routing :: C6509-E And VS-S720-10G Visio Stencils?
Sep 9, 2009I need those two stencils.I have checked here [URL] but:
- the one for the C6509-E is not there
- the one for the supervisor does not work properly (misaligned anchor points).
Cisco Switching/Routing :: QOS On 4500E With Sup7-E?
Mar 25, 2012I was contacted by a customer today who is trying to configure QoS on a 4500E with Sup7-E. They are running:
cat4500e-universalk9.SPA.03.02.00.SG.150-2.SG.bin
And the 4500 is licensed for enterprise Services. I don't have access to the switch and am looking for configuration documentation and I am not finding the necessary configuration guides.
Cisco Switching/Routing :: What MIB ID For 4500 SUP7-E
Apr 22, 2013How to know 4500 SUP7-E's MIB ?Our customer use MS SCOM 2012 SP1 get the OID are 1.3.6.1.4.1.9.1.1286, but we use IOS MIB locator, we can not find this MIB id.
below are the IOS sh version information :
Cisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500e-UNIVERSAL-M), Version 03.02.00.SG RELEASE SOFTWARE (fc4)
Technical Support: [URL]
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Tue 26-Apr-11 18:09 by prod_rel_team
[code]....
Cisco Switching/Routing :: Visio Icons For 3508 / 3524 And 3548 Switches?
May 13, 2012Where I can find the visio icons for the cisco 3508, 3524 and 3548. They are NOT on the cisco visio icon download site.
View 3 Replies View RelatedCisco Switching/Routing :: Enable All 4 10G Ports On WS-X45-Sup7-e Supervisor Module?
Dec 7, 2011How do I enable ports 3 and 4 on this supervisor module? I can only get ports 1 and 2 to work by default. I have a standby Supervisor in SSO mode. I'm running IOS 15.0.2SG
View 2 Replies View RelatedCisco Switching/Routing :: Core 4506 / Difference Between Sup7 And Sup7L?
Aug 17, 2012I will go to buy a core 4506 but I'm comfusing about the Sup engines and the Fiber module. What is the different between the Sup7 and Sup7L?in the fiber module that I will go to buy is it contain the SFP inside or I have to buy the SFP ( WS-X4612-SFP-E ). also what is the different between the SFP and GBIC?
View 4 Replies View RelatedCisco Switching/Routing :: 4500 Internal Virtual Interface On SUP7
Jul 22, 2012We recently had a contractor deploy a 4500 catalyst switch with a WS-x45-SUP7-E. After installation and configurations, HP openview is detecting a "downed" interface on the 4500 chassis that is not in the configuration. I have attached an image with the interface circled. We assumed that it may be a configuration issue with openview, however after running diagnostics with a network analyzer, the same ip address for the down interface is still detected. Is this some sort of internal virtual interface on the SUP7?
View 4 Replies View RelatedCisco Switching/Routing :: Unable To Enable Netflow On Cat 4503-E (Sup7-E)
Dec 17, 2011I am working with a Catalyst 4503-E with a Sup7-E. I'm trying to enable Netflow, and I have read the following guides: Catalyst 4500 Series Switch SW Configuration Guide, Release IOS ...
I have also enabled Netflow in IOS 12.1/12.2 and figured the process was similar (It seems to be). CEF is enabled, and I have all the pre-reqs according to the document above, however, the flow commands don't exist, they simply say "command unrecognized". I have included my sh version below.
sh version (edited):
Cisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500e-UNIVERSAL-M), Version 03.01.01.SG RELEASE SOFTWARE (fc1)
[Code].....
Cisco Switching/Routing :: Possible To Configure QoS On 4500 Sup7 On Layer 3 Routed Port
Apr 26, 2013I want to know if is it possible to configure QoS on a 4500 Sup7 on a Layer 3 routed port like the following example (Similar to CBWFQ on IOS Router)?
View 3 Replies View RelatedCisco Switching/Routing :: Interface Numbering Plan On CAT4500E With SUP7-E Or SUP7L-E
Feb 1, 2013We are planning for the first installation of 4500 switches containing these supervisor modules. I'm trying to determine the interface numbering convention for ports on the supervisors. Our existing 4500E all have SUP6 modules with twin-gig converters - so I am familiar with the numbering conventions used on those supervisors. How does this change with the software based selection command "hw-module uplink select" used in SUP7?
View 2 Replies View RelatedCisco Switching/Routing :: Cat4500 Sup7 How To Limit Rendezvous Points Connecting To Bootstrap Routers
May 21, 2013In testlab we use pim-sm with bootstrap router on sup7 with IOS-XE 03.04.00.SG. Any possibility to prevent non authorized rp from connecting to the candidate bootstrap routers? We found several security recommendations concerning limiting registering of sources at the rp, rate-limits etc, but no possibility to control rp connecting to the bsr.
View 4 Replies View RelatedCisco Switching/Routing :: LLDP-MED TLV Commands - Cat45010+E Sup7 And Polycom CX600 Lync Phones
Oct 15, 2012I'm trying to configure LLDP-MED between a Cat45010+E Sup7 (IOS 15.1) and Polycom CX600 Lync phones. I have created and applied the correct network policy for the interfaces.
From these sites, I need to send all the correct TLVs or the phones won't respond: {URL}.
When a scour the config of the switch, I can't find any related configuration commands relating to the specific LLDP-MED TLV components which are enabled/disabled. Where are they hiding? I would like to confirm which TLVs are being sent by my switch and if they are matched to the phone. I can always use the DHCP method, put this is not preferred.
Cisco Switching/Routing :: Auto QoS On 4507R-E?
Mar 15, 2010I have a 4507R-E chassis with Supervisor IV running IOS 12.2(50)SG. I am trying to configure "auto qos voip trust" on some of the uplink ports. When I try to configure it on a port that is in a channel group, I get the error "AutoQoS Error: AutoQoS can not be configured on member port(s) of a port-channel". I have also tried configuring it on the channel interface, but it is not an available command under the channel interface. Is there a way to do auto qos on the channel interfaces or their member ports or does it have to be configured manually?
View 12 Replies View RelatedCisco Switching/Routing :: 4507R - CPU Utilization 90%?
Dec 15, 2011I am facing high CPU utilzation for cisco4507R,
sup:
WS-X4516-V
ios version:
cat4500-entservices-mz.122-54.SG.bin
!
show process cpu
CPU utilization for five seconds: 97%/1%; one minute: 97%; five minutes: 97%
[code]....
Cisco Switching/Routing :: 4507R Switch SUP Cards
Apr 19, 2013I have two types of 4507 switches
1. 4507R
2. 4507R-E
and SUP-V and SUP-6-E.So I want to test both SUP cards on both switches which SUP card support which switch?
Cisco Switching/Routing :: Are Cat 4507R Supervisors Hot Swappable
Feb 19, 2013I received an replacement supervisor from Cisco to swap out the failed standby supervisor. I wanted to check if I can pull out the failed supervisor supervisor and insert the replacement supervisor while the switch is still on. In other words, is it hot swappable? Also, will this operation cause interruption of switching inside the 4507R switch?
View 6 Replies View RelatedCisco Switching/Routing :: Power Consumption On 4507R
Aug 2, 2010We are planning for the office move and I need to estimate how much power we need to run a fully populated Cat4507R switch. The chassis include 2 Sups, one 6-port fiber line card, two 48-port Gig and two 48-port FastEthernet line cards. The switch also has redundant power supply (4200ACV 1400W). According to Cisco Power Calculator [URL], I need 49.5 amp 110-120V circuit. It seems to be too much higher than real world. How many 20amp circuit we would need when all the ports are fully utilized?
View 3 Replies View RelatedCisco Switching/Routing :: Upgrade On 4507R+E Single SUP?
Mar 3, 2013how to upgrade firmware on 4507 6L-E Sup. There is only 1 Sup on the switch. is there any special requirement to update the firmware when switch not running on redundancy mode?
-core-1#show redundancy states my state = 13 -ACTIVE peer state = 1 -DISABLED Mode = Simplex Unit = Primary Unit ID = 3
Redundancy Mode (Operational) = Stateful Switchover Redundancy Mode (Configured) = Stateful SwitchoverRedundancy State = Non Redundant
[Code] ......
Cisco Switching/Routing :: 4507R Bootflash Memory
Dec 28, 2011I have a bootflash in 4507R with the size of 60MB. I upgraded the ios from cat4500-ipbasek9-mz.122-37.SG1.bin (12.8MB Size) to cat4500-entservices-mz.122-37.SG1.bin (13.8 MB SIZE) and deleted the previous IOS.But previous IOS is still getting shown in sh bootflash: command. Furthermore, dir bootflash: commands shows there is only one IOS , which is running. How I can free the space from bootflash , as I again have to upgrade the another new IOS ( of 16MB), which I tried through solarwinds tftp and couldn't upload successfully because of its limitation. Now, If I try to upload the new IOS through FTP, it gives me memory space error. How I can free the space captured by old IOS and also how I can delete the 3rd unknown entry of IOS (shown below output of commands)?
View 4 Replies View RelatedCisco Switching/Routing :: Config Register On 4507R
Jun 5, 2012Need to confirm on 4507 R switch should i set config reg to 0x2102 or 0x2101?
View 4 Replies View RelatedCisco Switching/Routing :: Is 4507R FAN Tray Hot Swappable
May 27, 2012We have a Cisco 4507R switch with sup V. This switch fan tray has partial problem .No light in fan tray. We got another fan tray. Can any one tells me is it hot swappable?
What procedure should I flow without any interruption our live network?
Cisco Switching/Routing :: Getting 4507R+E FE0 Management Port?
Nov 1, 2012Is there some kind of trick to getting the fastethernet 0 management port to come up? My adjacent switch is up/up, but fe0 is down/down. I dont' see how this could be possible. I am getting all my info remotely, but I am pretty sure it's wired up correctly.
View 2 Replies View RelatedCisco Switching/Routing :: 4507R Classic Chassis With Sup 6L-E
Jan 4, 2012Configuring a 4507R classic chassis with redundant Sup 6L-E? TAC told me the Supervisor 6LE was only supported on the 4507R+E or 4507R-E chassis but I have found in Cisco documentation several places that indicate that the Sup 6LE is supported in the classic chassis.
View 1 Replies View RelatedCisco Switching/Routing :: 4507R-E - Configuration For VLans
Mar 4, 2013I'm unable to pass the required vlans networks to my firewall I have different vlans configured for each floor of the building, All these floors have Nortel switches which are connected to the core switch through fiber link.
I have a Cisco 4507R-E core switch. Config for the core switch below: what else has to be done in order to pass the vlans to my firewalls.
Current configuration : 18527 bytes
hostname HQ_Prim_Core_Swt
boot-start-marker
boot-end-marker
enable secret 5 $1$xj2Z$TmV9chRtQWCuXYMsCtBVW/
enable password 7 13521317135C0729
[code]....
Cisco Switching/Routing :: Multicast Hogging 4507R
May 30, 2013i tried a stab and multicasting a FOG image to 4 machines the other day, and i had experienced odd and strange issues.
here is what i encountered:,100% cpu usage on our core switch,core4507#sh processes cpu hist
9999999999999999999999999999999999999999999999999999999999
7777888888888877777888888888888887777788888888888888888887
100 **********************************************************
[Code]...
pinging the SVI on the core and or pinging on the core to other devices resulted in MAJOR latencies, packet loss due to the cpu usage, etc.... no other network operations were affected, i could communicate with the rest of the network, and under 1-2ms latencies. i noticed it due to my opsview server flagging the core as down (SNMP OID's wouldnt return a value)
it lasted the whole time i was multicasting, i kept a close eye on it. i highly considered canceling my job, but everything ran smooth.when i looked at the cpu sorted history i saw 2 processes, IP Input, and cat4k mgmnt hipri
Cisco Switching/Routing :: Configuring 4507R For LACP And Trunking?
Apr 3, 2008We're trying to configure our Cisco 4507 (Supervisor Engine IV) to allow a new Dell server with a pair of Broadcom 5708 GigE NIC's to aggregate its NIC's to give us a 2gbps link to the switch.
So far we seem to have got the team and LACP up and enabled, but the adaptor that the Broadcom Admin Util creates for the team is only showing a 1gbps connection where I would have expected it to show as 2gbps.
The individual NICs show as connected at 1gbps. We're not Cisco experts so are struggling on how to get the 2 NICs to aggregate.
On the server side we've done nothing other than create a team using 802.3ad LINk Aggregation using LACP.
This is what I think the relevent output from "sho conf" is, more available if needed.
version 12.2
boot system flash bootflash:cat4000-i9s-mz.122-18.EW1.bin
!
interface Port-channel2
[Code].....
Cisco Switching/Routing :: Shutdown 4507r-e And Just Swap Out Blade?
Apr 2, 2012If i replace a card of the same type in the same slot will I lose the configuration for that card or does it live in the backplane of the device?Is there any special command I need to run to replace the card or can i shutdown the 4507r-e and just swap out the blade?
View 3 Replies View RelatedCisco Switching/Routing :: 4507r / Format Of Flash Caused 100% CPU?
Jul 21, 2012I had an issue today on a 4507r today where when I formatted the compact flash in slot0: (512mb) it caused the CPU to spike to 100% this took about 1.5 hours and did not cause adjacency loss or any thing, but was worrisome. This was a sup IV is this normal and should u let it complete like I did? Also when I copied the os to it from boot flash it caused the same behavior. I have done this a bunch in 6500 sup 720 without this issue?
View 3 Replies View RelatedCisco Switching/Routing :: 4507R+E / SSO Not Available As Redundancy Mode Option
Oct 31, 2012Why rpr is the only available redundancy mode option available to me. I'm running a 4507R+E with twin SUP7-E's.
Abbreviated show ver Cisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500e-UNIVERSALK9-M), Version 03.03.01.SG RELEASE SOFTWARE (fc2)Technical Support: [URL]/techsupportCopyright (c) 1986-2012 by Cisco Systems, Inc.Compiled Sun 26-Aug-12 13:45 by prod_rel_team
ROM: 15.0(1r)SG2gp08401 uptime is 6 weeks, 6 days, 4 hours, 59 minutesUptime for this control processor is 6 weeks, 3 days, 2 hours, 21 minutesSystem returned to ROM by RPR SwitchoverSystem image file is "bootflash:/cat4500e-universalk9.SPA.03.03.01.SG.151-1.SG1.bin"Jawa Revision 7, Snowtrooper Revision 0x0.0x1C
[code]....
Cisco Switching/Routing :: Secon SUP Engine On 4507R Switch?
Mar 8, 2012I need to add another SUP engine on Cat 4507R switch, with a new one. I have old SUP engine running in this switch. Sometime this switch is reloaded without any reason. So we want to add another sup engine for redundancy. What is the procedure to do this & also how much outage time would it cause? Which sup engine will be run as primary and which one should be redundancy?
SWITCH-4507#sh ver
Cisco IOS Software, Catalyst 4000 L3 Switch Software (cat4000-I9K91S-M), Version
12.2(25)EWA8, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Wed 24-Jan-07 15:28 by pwade
[code]....