I have 8 2504 controllers and each needs to have a minimum of 20 MAC addresses added. I would rather not add them one at a time but I don't see any features that allow for an import. Any way to do the import?
View 2 Replies
I have wlc AIR-CT2504-K9. After save config and power down, wlc cannot start. In console I see:
WLCNG Boot Loader Version 1.0.16 (Built on Feb 28 2011 at 13:14:54 by cisco)
Board Revision 0.0 (SN: PSZ163201YR, Type: AIR-CT2504-K9) (P)
Verifying boot loader integrity... OK.
OCTEON CN5230C-SCP pass 2.0, Core clock: 750 MHz, DDR clock: 330 MHz (660 Mhz da ta rate)
CPU Cores: 4
[Code].....
We have 1 WLC + 17 AP's on our main site and thats working fine... we just buyed a new AP for a new site of us. Its the same domain, same ip range nothing special at all... Somehow the AP on the site keeps rebooting and the users getting nervous of it there
Specs:
WLC: AIR-CT2504-K9
Software Version: 7.2.110.0
AP:AIR-LAP1042N-E-K9
Software version: 7.2.110.0
[code]....
AIR-CT2504-25-K9 will support AIR LAP1142N-E-K9
View 3 Replies View RelatedI configured a 2504 controller with two LWAPP Access Points, and I'm using two SSID's on the same controller, the problem is when the user tries to switch between SSID's he gets an error message saying that the other network is unavailable but if he disconnects from the first network and then connects to the other it works fine !.
View 5 Replies View Relatedsome computers is connecting to AP that is farthest, But there are two APS closer and the signal gets too low, the computer only connects to the closest AP if I disconnect and reconnect.I have 2 controllers series 2500 model AIR-CT2504-K9.
View 5 Replies View RelatedOn the WLC I've set DHCP address pool, everything seems fine after ap download image -> reboot -> hit "Enter" to start blar blar blar... however, after a few second the WLC will initial upgrade image again and again. it's like a non-stop process.
Attached is the start up message, as you can see, i captured it after the ap successfully boot up, and WLC initial another cycle of image upgrade.
btw, my network is flat, WLC & AP all in the same network.
*Nov 3 06:28:30.788: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
examining image...!
extracting info (292 bytes)
[Code].....
I have bought 2504 LAN Controller and my old 1142 wants to configure to accept that Controller instead of old controller. These APs and controllers in far away site and before I go there I want to figure out how can I do following.
1. How can I configure old 1142(Previously connected with another LAN Controller) to accept New 2504 Controller instead of old controller ?
2. What are the concerns do I need to consider?
City A is the data center with 2 WLC (CT2504-K9) and a number of AP. City B is a branch with MPLS between A and B. Right now the APs at City B has joined the controller. Users at B is getting ip's assigned from DHCP at City A. How do I configure the WLC so users can get ip's assigned from DHCP server present at B. Option 43 is enabled.
View 2 Replies View Relatedtell me when is available for order the High Availability for AIR-CT2504, like:
AIR-CT7510-HA-K9 Cisco 7500 Series High Availability Wireless Controller
AIR-CT5508-HA-K9 Cisco 5508 Series Wireless Controller for High Availability
I've just been tasked with setting up 19 AIR-CT2504 WLCs with AIR-CAP3502E APs. The primary objective is to maximize throughput from clients uploading LARGE files over the air.
I need to make sure I config HT 802.11n properly with no support for legacy clients in the 5Ghz band.
I have inherited a site where the builders have installed a 2504 controller with 8 access points. Unfortunately they have not created an ap-manager interface when they did the set up. Is there any way I can do this via GUI or command line without going back to defaults?
View 7 Replies View RelatedI have AIR-CT2504-5-K9, with 5 access point license support. I buy capacity adder license LIC-CT2504-5A for add 5 access points more. When i try download licence file from tftp server on WLC system i see message "License 1 Failed 1" on WLC. TFTP server message downloading OK.
View 4 Replies View Relatedi have AIR-CT2504-5-K9, with 5 access point license support. I buy capacity adder license LIC-CT2504-5A for add 5 access points more. When i try download licence file from tftp server on WLC system i see message "License 1 Failed 1" on WLC. TFTP server message downloading OK.
View 7 Replies View RelatedI am using two AIR-CT2504-K9 controllers
Product Version.................................. 7.4.100.0
Bootloader Version............................... 1.0.16
Field Recovery Image Version..................... 1.0.0
Firmware Version................................. PIC 16.0
and 20 access points AIR-CAP2602I-E-K9 Cisco IOS Software, C2600 Software Version 15.2(2)JA, RELEASE SOFTWARE (fc1) LWAPP image version 7.4.100.0
I created 3 SSID:
1. [WPA2][Auth(PSK)]
2. Web-Passthrough
3. [WPA2][Auth(PSK)]
Configuration on controllers is identical. High Availability is configured on all APs. First controller controls only those APs witch have SSIDs with [WPA2][Auth(PSK)], second controller is basically for APs with Web-Passthrough SSID. From the start I have problem, some clients who try to connect to SSID with PSK are dropped or can’t connect entirely, but when they go to the next AP they connect successfully. For example I have Android smartphone and Lenovo laptop, smartphone connects successfully but laptop fails connection to the same AP, but when I take it to other AP it connects successfully. Sometimes smartphones can’t connect too. When devise can’t connect to one SSID it can’t connect to other SSID either. Sometimes there are up to 20 clients tying to connect to the same AP.
When I look into logs, I get these two messages:
Jun 3 08:58:58 192.168.224.1 WLC1: *dot1xMsgTask: Jun 03 08:58:51.176: #DOT1X-4-MAX_EAPOL_KEY_RETRANS: 1x_ptsm.c:456 Max EAPOL-key M1 retransmissions exceeded for client 7c:e9:d3:f4:74:4d
[Code].....
I've got a new CT2504 controller with software version 7.0.220.0 Regarding to [URL]I've tried to configure the internal DHCP on a dynamic-interface, but this is not possible:(Cisco Controller) >config interface dhcp dynamic-interface vlan401 primary 172.16.x.3 vlan401 Interface IP can not be used as internal DHCP server IP It works, if I use another IP (aka DHCP server) in the same subnet or in another subnet. It works also for the management interface.
(Cisco Controller) >show interface detailed management
Interface Name................................... management
MAC Address...................................... d0:c2:82:xx:xx:xx
IP Address....................................... 10.2.x.135
IP Netmask....................................... 255.255.255.240
IP Gateway....................................... 10.2.x.129
[code].....
We have just installed our first CT2504.After install I have found a dramatic drop in signal strength compared to the wireless survey result obtained.All of our site surveys include real world testing using an AP, in this case a AP1041N.In doubt I retested a section using an AP1041N in the same location as one of the recently deployed LAP1041N.
In the same location a LAP1041N has between -10 and -20dbi difference in SNR compared to the test AP1041N.For example locations that tested with -60dbi using an AP1041N have little to no coverage using the LAP1041N installed.This applies irrespective of the WLC automatic control over Tx power or manually setting the LAP TX to the highest level.
I have a CT2504 at a customer site which does not load the captive portal page correctly nor will it load via HTTP as opposed to HTTPS.So for starters I did what I do with all my CT2504's (which work fine), I configured my Guest network to authenticate via the default captive portal. I then disabled HTTPS and SSH and enabled HTTP managment followed by rebooting the controller. On boot, logging into the WLC management GUI is automatically presented via HTTP as expected.However when clients access the Guest network they are redirected to the Web Authorisation via HTTPS instead of HTTP?In addtion to the above the captive portal page does not display correctly.The preview via the controller works fine, but the client is presented with a page with broken links to the images i.e. the blue strip at the top and the Cisco logo on the right.
View 3 Replies View RelatedI´m trying to connect them to my WLAN, for throubleshoot I create a new WLAN with WPA2-TKIP and a PSK, the devices didin´t connect to the WLAN.I also change the security to WPA2-AES with TKIP, it didn´t work too.
My best choice was to disable every security configuration in order to began the throubleshooting from zero, but even with no Layer 2 and 3 security, the devices didn´t connect to my Test WLAN.
I´m using a AIR-CT2504-K9 WLC with two AIR-CAP3502I-A-K9 AP, all the PCs and other brand cellphones and tablets work well.
Also I have a SOHO router on the office, and the IPad connect without a problem with that WLAN, but I need them to connect to my Cisco AP.
I was wondering if there was a way to import a large number of mac addresses into the MAC filtering of a Cisco WLC 4400. We recently purchased 150 new Mac laptops and I need to add them to the Mac filtering. I have 5 WLC's to do this to.I already have the MAC addresses and names in a spreadsheet.
View 3 Replies View RelatedIn one week I need to import the config from my 4404 WLC to my new 5508, then I just want to change the mgnt IP address of the 5508 and then bring it into the same mobility group.How do I import the config when the 5508 is straight out of the box?
View 13 Replies View Relatedwe need to be required to import MAC filter databse from Cisco Wireless LAN Controller (4400) to Cisco ACS Server (v4.2).
View 2 Replies View RelatedI would like to use the NCS 1.2 to monitor Juniper SRX 210 firewall. When I try to import the MIB File from NCS, which show "Error: Failed to load MIB File "mib-802" because it is not in the resource path.what I can upload the MIB File from Juniper. [code]
View 0 Replies View RelatedDo you know the procedure of import SSL certificate from Godaddy to ASA 5510? attached is the drop-down list that I have to choose from.
View 5 Replies View RelatedCan I import a self signed certificate from a Cisco 871 router to a Cisco ASA 5505? The 5505 replaced the 871 and I have a VPN that goes to another company that we have a connect to. The device on the other end is a VPN concentrator ( I do not have access to modify this device without going through multiple channels.) I only need to mimic this device for the site to site VPN tunnel only. It appears that there are no pre-shared keys only a self signed certificate.
View 1 Replies View RelatedI'm trying the csv file import and getting some errors.
010-12-07 14:23:47: File Format Validation Completed2010-12-07 14:23:47: Import Started
2010-12-07 14:23:47: Record number: 1, Host 01-02-03-04-05-06: Import Failed2010-12-07 14:23:47: null Import process failed for unexpected reason: Unknown error has accurred.2010-12-07 14:23:47: Import Completed With errors
-------- Summary --------Total Number of Records Processed:1Number of Records Failed:1Number of Records Imported:1---------- End ----------Please refresh the table to see the changes.
On some other tries I get null field or missing fields.
It actually creates the host, but on editing it I get the following message:
An unexpected error has occurred. To continue your work, reselect the option in the left navigation bar.If you continue to receive the unexpected error message, close your browser and log in to ACS again.If you still receive the unexpected error message, contact your system administrator or technical assistance.
MACAddress:String(64):Required,description:String(1024),"enabled:Boolean(true,false):Required",HostIdentityGroup:String(256),VLAN:String(256):Required,attr-Expiration Date:Date(yyyy-Mmm-dd)01-02-03-04-05-06,AAATest,true,,Guest,2010-Dec-08
i tried to import a IOS from a network device into the software repository but the job fails with the following line in the log:
sw-10-ed24#
sw-10-ed24#dir /all flash:
Directory of flash:/
[Code].....
The chosen protocol ist SCP and the option "Use SSH for software image upgrade and software image import through CLI(with fallback to TELNET)." is enabled.
I have an SG200 switch and am trying to import a certificate signed by my own CA. I generate the CSR and sign it using Java's key tool with my own root cert. When I attempt to import the resulting cert, the switch blanks out the certificate text box and deletes all of my d name data (CN, etc) from the switch. What am I missing?
View 2 Replies View RelatedI'm currently in the process of the setting up a new wireless network and I want to test out our 7925 phones on it. When I try uploading the certificate to the phone it fails and I find the following error in the trace logs
[code]...
I created this certificate using using Windows Server 2003 and it is 2048 bits. This certificate works fine with my laptop but I'm unable to upload it to the phone. The app load currently on the phone is CP7925-MFG-D.8.LOADS. Are there any specific guidelines out there when creating a certificate for a Cisco 7925 phone?
I have 2 PIX 525, which one of them, step and active failover mode the other PIX 525, leaving this off, do not know what happened may have been a power outage, but in any case I can turn it back on? And the other question I have is if I can import a configuration that I have saved on my computer. i have the PIX device manager.
View 11 Replies View RelatedI am migrating WCS to PI 1.3. I read from the guide that we need to migrate to NCS 1.1.1 first and we can get the demo license from Cisco.but the demo license is only 100 unit, but my WCS has 300 license units.How can I import the wcs data to NCS? Besides, I also read from the guide that I need to install patch in NCS before migrating the data to PI 1.3.can I install the patch before i import the data from WCS?
View 2 Replies View RelatedI cannot import certificate from CA (Certificate Authority). When I attempt to install the certificate to CSACS SE 4.2, the following error occurs during installation: "Unsupported private key file format".
View 7 Replies View Relatedon ACSv5.2...are there any limitations on the number of users that can be imported via CSV file...i.e. will the ACS handle 250,000 internal users for example?
View 1 Replies View Related
