Cisco Wireless :: 1142 Keeps Downloading Image From WLC CT2504
Nov 2, 2012
On the WLC I've set DHCP address pool, everything seems fine after ap download image -> reboot -> hit "Enter" to start blar blar blar... however, after a few second the WLC will initial upgrade image again and again. it's like a non-stop process.
Attached is the start up message, as you can see, i captured it after the ap successfully boot up, and WLC initial another cycle of image upgrade.
btw, my network is flat, WLC & AP all in the same network.
*Nov 3 06:28:30.788: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
examining image...!
extracting info (292 bytes)
[Code].....
View 19 Replies
ADVERTISEMENT
Jan 19, 2013
trying to join an 1142 on a WLC_SRE version 7.4.
the AP can ping the controller and vice versa. In the controllers GUI: Monitor>Statisticc>AP join, I can find the mac of the AP that I am trying to get joined.
the details of this mac show:
Last error occurred: Lwapp discovery request rejected
last occurred error reason: Too many concurrent AP image downloads
Last Join Timestamp:
View 6 Replies
View Related
Jun 5, 2013
I have wlc AIR-CT2504-K9. After save config and power down, wlc cannot start. In console I see:
WLCNG Boot Loader Version 1.0.16 (Built on Feb 28 2011 at 13:14:54 by cisco)
Board Revision 0.0 (SN: PSZ163201YR, Type: AIR-CT2504-K9) (P)
Verifying boot loader integrity... OK.
OCTEON CN5230C-SCP pass 2.0, Core clock: 750 MHz, DDR clock: 330 MHz (660 Mhz da ta rate)
CPU Cores: 4
[Code].....
View 2 Replies
View Related
Aug 8, 2012
I have 8 2504 controllers and each needs to have a minimum of 20 MAC addresses added. I would rather not add them one at a time but I don't see any features that allow for an import. Any way to do the import?
View 2 Replies
View Related
Nov 4, 2012
We have 1 WLC + 17 AP's on our main site and thats working fine... we just buyed a new AP for a new site of us. Its the same domain, same ip range nothing special at all... Somehow the AP on the site keeps rebooting and the users getting nervous of it there
Specs:
WLC: AIR-CT2504-K9
Software Version: 7.2.110.0
AP:AIR-LAP1042N-E-K9
Software version: 7.2.110.0
[code]....
View 4 Replies
View Related
Apr 4, 2012
AIR-CT2504-25-K9 will support AIR LAP1142N-E-K9
View 3 Replies
View Related
Sep 6, 2012
I configured a 2504 controller with two LWAPP Access Points, and I'm using two SSID's on the same controller, the problem is when the user tries to switch between SSID's he gets an error message saying that the other network is unavailable but if he disconnects from the first network and then connects to the other it works fine !.
View 5 Replies
View Related
Apr 9, 2013
some computers is connecting to AP that is farthest, But there are two APS closer and the signal gets too low, the computer only connects to the closest AP if I disconnect and reconnect.I have 2 controllers series 2500 model AIR-CT2504-K9.
View 5 Replies
View Related
Jan 8, 2013
I have bought 2504 LAN Controller and my old 1142 wants to configure to accept that Controller instead of old controller. These APs and controllers in far away site and before I go there I want to figure out how can I do following.
1. How can I configure old 1142(Previously connected with another LAN Controller) to accept New 2504 Controller instead of old controller ?
2. What are the concerns do I need to consider?
View 19 Replies
View Related
Apr 16, 2012
City A is the data center with 2 WLC (CT2504-K9) and a number of AP. City B is a branch with MPLS between A and B. Right now the APs at City B has joined the controller. Users at B is getting ip's assigned from DHCP at City A. How do I configure the WLC so users can get ip's assigned from DHCP server present at B. Option 43 is enabled.
View 2 Replies
View Related
Jun 2, 2013
tell me when is available for order the High Availability for AIR-CT2504, like:
AIR-CT7510-HA-K9 Cisco 7500 Series High Availability Wireless Controller
AIR-CT5508-HA-K9 Cisco 5508 Series Wireless Controller for High Availability
View 1 Replies
View Related
Apr 7, 2013
I've just been tasked with setting up 19 AIR-CT2504 WLCs with AIR-CAP3502E APs. The primary objective is to maximize throughput from clients uploading LARGE files over the air.
I need to make sure I config HT 802.11n properly with no support for legacy clients in the 5Ghz band.
View 22 Replies
View Related
Jan 23, 2013
I have inherited a site where the builders have installed a 2504 controller with 8 access points. Unfortunately they have not created an ap-manager interface when they did the set up. Is there any way I can do this via GUI or command line without going back to defaults?
View 7 Replies
View Related
Apr 3, 2012
I have AIR-CT2504-5-K9, with 5 access point license support. I buy capacity adder license LIC-CT2504-5A for add 5 access points more. When i try download licence file from tftp server on WLC system i see message "License 1 Failed 1" on WLC. TFTP server message downloading OK.
View 4 Replies
View Related
Jan 8, 2013
i have AIR-CT2504-5-K9, with 5 access point license support. I buy capacity adder license LIC-CT2504-5A for add 5 access points more. When i try download licence file from tftp server on WLC system i see message "License 1 Failed 1" on WLC. TFTP server message downloading OK.
View 7 Replies
View Related
Jun 2, 2013
I am using two AIR-CT2504-K9 controllers
Product Version.................................. 7.4.100.0
Bootloader Version............................... 1.0.16
Field Recovery Image Version..................... 1.0.0
Firmware Version................................. PIC 16.0
and 20 access points AIR-CAP2602I-E-K9 Cisco IOS Software, C2600 Software Version 15.2(2)JA, RELEASE SOFTWARE (fc1) LWAPP image version 7.4.100.0
I created 3 SSID:
1. [WPA2][Auth(PSK)]
2. Web-Passthrough
3. [WPA2][Auth(PSK)]
Configuration on controllers is identical. High Availability is configured on all APs. First controller controls only those APs witch have SSIDs with [WPA2][Auth(PSK)], second controller is basically for APs with Web-Passthrough SSID. From the start I have problem, some clients who try to connect to SSID with PSK are dropped or can’t connect entirely, but when they go to the next AP they connect successfully. For example I have Android smartphone and Lenovo laptop, smartphone connects successfully but laptop fails connection to the same AP, but when I take it to other AP it connects successfully. Sometimes smartphones can’t connect too. When devise can’t connect to one SSID it can’t connect to other SSID either. Sometimes there are up to 20 clients tying to connect to the same AP.
When I look into logs, I get these two messages:
Jun 3 08:58:58 192.168.224.1 WLC1: *dot1xMsgTask: Jun 03 08:58:51.176: #DOT1X-4-MAX_EAPOL_KEY_RETRANS: 1x_ptsm.c:456 Max EAPOL-key M1 retransmissions exceeded for client 7c:e9:d3:f4:74:4d
[Code].....
View 2 Replies
View Related
Apr 5, 2012
I've got a new CT2504 controller with software version 7.0.220.0 Regarding to [URL]I've tried to configure the internal DHCP on a dynamic-interface, but this is not possible:(Cisco Controller) >config interface dhcp dynamic-interface vlan401 primary 172.16.x.3 vlan401 Interface IP can not be used as internal DHCP server IP It works, if I use another IP (aka DHCP server) in the same subnet or in another subnet. It works also for the management interface.
(Cisco Controller) >show interface detailed management
Interface Name................................... management
MAC Address...................................... d0:c2:82:xx:xx:xx
IP Address....................................... 10.2.x.135
IP Netmask....................................... 255.255.255.240
IP Gateway....................................... 10.2.x.129
[code].....
View 1 Replies
View Related
Feb 9, 2012
I'm have upgraded our ASA5510's from 7.0.8 to 8.4.3 and now I just need to do the ASDM, but get this error? The bin file has been uploaded: [code] Device Manager image set, but not a valid image file disk0:/asdm-647.bin.
View 3 Replies
View Related
Jun 13, 2012
We have just installed our first CT2504.After install I have found a dramatic drop in signal strength compared to the wireless survey result obtained.All of our site surveys include real world testing using an AP, in this case a AP1041N.In doubt I retested a section using an AP1041N in the same location as one of the recently deployed LAP1041N.
In the same location a LAP1041N has between -10 and -20dbi difference in SNR compared to the test AP1041N.For example locations that tested with -60dbi using an AP1041N have little to no coverage using the LAP1041N installed.This applies irrespective of the WLC automatic control over Tx power or manually setting the LAP TX to the highest level.
View 5 Replies
View Related
Dec 11, 2012
I have a CT2504 at a customer site which does not load the captive portal page correctly nor will it load via HTTP as opposed to HTTPS.So for starters I did what I do with all my CT2504's (which work fine), I configured my Guest network to authenticate via the default captive portal. I then disabled HTTPS and SSH and enabled HTTP managment followed by rebooting the controller. On boot, logging into the WLC management GUI is automatically presented via HTTP as expected.However when clients access the Guest network they are redirected to the Web Authorisation via HTTPS instead of HTTP?In addtion to the above the captive portal page does not display correctly.The preview via the controller works fine, but the client is presented with a page with broken links to the images i.e. the blue strip at the top and the Cisco logo on the right.
View 3 Replies
View Related
May 22, 2013
I´m trying to connect them to my WLAN, for throubleshoot I create a new WLAN with WPA2-TKIP and a PSK, the devices didin´t connect to the WLAN.I also change the security to WPA2-AES with TKIP, it didn´t work too.
My best choice was to disable every security configuration in order to began the throubleshooting from zero, but even with no Layer 2 and 3 security, the devices didn´t connect to my Test WLAN.
I´m using a AIR-CT2504-K9 WLC with two AIR-CAP3502I-A-K9 AP, all the PCs and other brand cellphones and tablets work well.
Also I have a SOHO router on the office, and the IPad connect without a problem with that WLAN, but I need them to connect to my Cisco AP.
View 7 Replies
View Related
Oct 10, 2011
I'm looking at adding a Cisco 3750-X switch running c3750e-universalk9-mz.122-55.SE1 (IP base license) into a stack of 3750-G switches running c3750-ipbasek9-mz.122-55.SE1.bin Given that the version and feature sets are the same I don't forsee any compatibility issues. Would there be any reason why a universal image wouldn't stack correctly with other switches running the single .bin file?
View 9 Replies
View Related
Jul 8, 2012
I have Cisco AP 1142 standalone and I want this one to operate with WLC.
I have searched in Google, they said I need to upgrade AP1142.
I don't know how to upgrade it.
View 6 Replies
View Related
Aug 26, 2012
i have a problem using my usb to serial cable connection, i can connect to one router on my work, but i can't connect to AP 1142, (i have tested also con AP 1231).i have a laptop running windows 7 64 bits, before i use a win xp 32 bits, and i didn't have problems.i am using putty, and have installed tera term 4.74 but the same.connection details, 9600, 8, 1, N, N.
View 5 Replies
View Related
Apr 29, 2013
I can't get connectivity from laptop to AP using cross over or straight through cable to do a tftp transfer from tftp server on laptop to ap.
I held the mode button on ap and powered on to get to rommon. The ap has no ios so it goes to rommon anyway. ap light is blinking red.
ap: set
DEFAULT_ROUTER=10.0.0.1
IP_ADDR=10.0.0.1
NETMASK=255.255.255.224
[Code].....
View 3 Replies
View Related
Feb 28, 2013
After AP is booted it shows the following message and cannot able to join in WLC:
*Mar 1 07:13:37.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.71.16 peer_port: 5246
*Mar 1 07:13:37.000: %CAPWAP-5-CHANGED: CAPWAP changed state to
[Code].....
View 5 Replies
View Related
May 2, 2012
I'm trying to "resurect" an old wireless network made with Cisco Aironet 1100. One of the AP has lost its IOS (due to an error while trying to upgrade it through the web interface)
I tried to reload it with the "mode button". I can see in my TFTP server logs that the AP is downloading the IOS but nothing happens and the AP keep being stuck (leds are : red/green/red)
View 7 Replies
View Related
Jan 22, 2012
I just converted AP 1142 to LAP using the image "c1140-rcvk9w8-tar.124-21a.JA2.tar".
The WLC is a 5500 with 2 NIC : one on 192.168.0/24, one on a specific vlan 10.20/16
The main management interface is on 192.168/24 but we defined as management the interface on the 10.20/16 network.
For the access points, we use ports on a native VLAN on 10.20/16 with other available VLANS which are used for the wlan networks
We have 1152 APs which work fine on this config but that needed to be registered on the 192.168/24 network, then we moved them in their VLAN 10/20/16 and they work fine.
We also have 1142 APs which have been upgraded to LAP. These AP do not work with our architecture. They register correctly on the 192.168/24 network, but do not give access to the wlan VLANs. If they are moved in the 10.20/16 network, they don't register to the WLC (message : Timed out while waiting for ECHO repsonse from the AP). The AP do not get an IP.
is there a restriction with VALNs on these AP ? or is something false ?
View 11 Replies
View Related
Aug 28, 2011
I have an 1142 AP that I am unable to set back to factory defaults.Here is what I have done so far:
- boot AP while holding down the mode button
- ap: delete flash:private-multiple-fs
- yes
- ap: boot
- when the AP boots fully I try and enter any lwap ap commands and get "ERROR!!! Command is disabled"
- the AP name and password were reset to defaults but I am unable to get the IP address cleared.
I've also tried "clear lwapp private-config" and get an error saying the command is disabled.
View 4 Replies
View Related
Dec 9, 2012
I need to convert some 1142 APs to lightweight mode. They will connect to controllers running 7.3.101.0. I noticed there's two options of Lightweight IOS code available c1140-k9w8-tar.152-2.JA.tar and c1140-rcvk9w8-tar.152-2.JA.tar. Whats the difference between the two versions of code?
View 4 Replies
View Related
Aug 13, 2012
When we take a look at the internal antennas on the 1142 AP, we notice the 5ghz pointed all the same way, but for the 2.4ghz we can see each offset by 45/120 degrees. It was my understanding that all antennas are omnidirectionals on the 1142, why are those 2.4ghz antennas not all pointed the same way? onfiguration advantage and that each antenna is indeed omnicadirectional? Example, if I shut just one antenna off, do I lose a sector (120degree)?
View 5 Replies
View Related
Jul 27, 2011
I recently purchased another 1142 AP to expand out our current wireless infrastructure, my question is, what exactly needs to be done for this to work so that users can roam freely and auto-connect to the closet AP with the best connection without getting disconnected?
I have set all the settings the exact same on the new AP to match the existing AP. (How to save the configs into a file would be great, I am not sure how to do that)... But anyhow, before I launch it, I would like to be sure I am correct so I do not bring down the existing network. Of course, the only difference between the 2 are the IP addresses. AP1 is 192.168.2.2 and AP2 is 192.168.2.3
All computers are using Linksys Wireless-N cards.
View 2 Replies
View Related
Nov 1, 2012
The last three new APs I have received from our supplier (official Cisco 1142 LAPs) have all successfully connected to our 4400 series WLCs but are all reporting as being in an Operational Status of 'Down' ie their A/B/G/N radios are not broadcasting even though the APs are all in an enabled state. Furthermore, there is no steady green light showing on the APs - there is no light showing whatsoever (although they were displaying the familiar red-orange-green lights while they were pulling down the IOS images from the WLCs).
The only strange thing I have noticed is that in the AP config screen, the ‘Mini IOS version’ is shown as being v7.3.x. The other – working APs – we have of the 1142 series show v3.x. I know that controller code v7.2 and above only work with the newer 5500 and 7500 series WLCs. Could this be the issue and have any of you seen this issue previously? I am running WLC code v7.0.230.0.
View 34 Replies
View Related
