I am reading up on the ACS VMware appliance installation instructions and am a bit confused on the disk space requirements. It says 60Gb is required and then goes on to talk about 500GB for the secondary instance. Do I need more than 60gb? Is the secondary instance a separate machine or part of the same one?URL
View 5 RepliesWhat are the VMware requirements to run ACS4.1.4? Im trying to use a VM this as the migration server. According to the cisco docs, it states that: "ACS 4.1 has been tested on the VMWare ESX server with the following configuration:
•VMWare ESX Server 3.0.0
•16 GB of RAM
•AMD Opteron Dual Core processor
•300 GB hard drive
•Four virtual machines
•Windows 2003 Standard Edition
•3 GB of RAM for the guest operating system"
I understand it will work as it "has been tested" with those specs, but the doc does not state the minimum requirements for the virtual machine. I dont want to use/find 300GB of space if I only need 20GB(as an example) to make it work.
We need to move from ESX 3.5 to ESX 4.0 a virtual machine running Cisco Secure ACS per Windows version 4.2.
View 10 Replies View Relatedis it possible to install cisco acs 5.4 on vmware 8 workstation ?
View 1 Replies View RelatedAre there any recommendations for configuring the VM for the ACS 5.x? What are the required minimum CPU-Cycles to dedicate and also the minimum RAM to dedicate?
View 1 Replies View RelatedI'm with problems to migrate the ACS 5.1 hardware to ACS 5.1 vmware. In my infraestructure I have a appliance with ACS 5.1 and I need to migrate to vmware to do HA. I installed vmware as the Cisco ACS recommendations. I made a backup of the ACS hardware and copied the local disk vmware ACS.
When I start the restore process after a few minutes an error occurs:
UMA/admin# dir
Directory of disk:/
33293306 Jun 08 2011 16:51:38 bkp-production-110608-1433.tar.gpg
5862 Nov 07 2009 01:06:32 favicon.ico.1
16384 Jun 06 2011 17:54:34 lost+found/
[Code]....
I am trying to install ACS 5.0 on workstation, however once the install finsihes it reboots and I enter the Linux bash command line rather than the Cisco CLI.
Note - this is now fixed. I followed the steps here to install ACS 5.0 on VMware Workstation 7: url...
I have a client that is running ACS 5.3 as a VM in ESX 4.1. The client wants their VMWare admins to have the ability to shut down the ACS server during maintenance etc... I know I could create a CLI user with admin priviliges, however, assigning full admin priviliges is beyond the scope of what the user requires. They simply want a user account with the added privilige of performing a halt from the CLI. In the CLI Reference Guide for ACS.
So is it possible to create an account with user priviliges, then modify its permissions to allow for a halt?
it's possible to install ACS Remote Agent 4.2.1 on VMWare server. Is it supported by Cisco?Do you have any experience with running the remote agent on VMWare servers?
View 2 Replies View Relatedto backup an ACS 5.3 vm running on ESXi 5.0 our backup admin requested to install vmware tools on the acs server.
View 2 Replies View Relatedin LMS (4.1) installing guide, table 'Software and Hardware Requirements for Soft Appliance', it is stated Memory and CPURequirement:
• 4 GB, 2 virtual CPU (< = 500 devices)Host CPU Core clock speed:
• Minimum 2.26 GHz Minimum Virtual CPU Reservations: Number of recommended virtual CPUs x 2.26 GHz:
• 4520 MHz (< = 500 devices)
I have HP server with 6 core CPU 2.0GHz - does it mean it does not meet the minimum system requirements (2.26Ghz)? Will I be able to go pass the installation?
According to the Installation notes for ACS 5.3 we need 500GB of storage for a working installation - if not it defaults to taking 60 GB of disk space for an eval version.
View 1 Replies View Relatedhow to setup 802.1x on the Cisco 500 Series Switches.I have done the whole implamentation in the past with Catalysts and ACS.But would like to see a guide for the 500 series.Do we need the Cisco ACS or can we use RADIUS on Windows?
View 1 Replies View RelatedI am planning to implement SSL-VPN (Any Connect) on an ASR 1002 router running IOS-XE Software Version 15.1(3)S2. I need to use LDAP for user authentication, and need to understand what are RADIUS/ TACACS requirements to use LDAP. Do I need to use Cisco ACS or can I use something like Microsoft IAS or Free Radius?
View 6 Replies View Relatedregarding the power requirements. I have this Cisco 6503-E switch and I need to know what I need in terms of power.
The manual says if using 120VAC, I will need 16A. If using 230VAC, the unit will require 8A.
I have 2 dedicated 20amps circuits both at 120V. Am I correct on plugging each of the power supplies of the cisco unit to each of these circuits?
Another question will be, do I really need to dedicated 2 dedicated 20amps circuits for the unit? Can't I just use one dedicated 20amps circtuis and connect both power supplies to it?
In Cisco ASDM 7.1(1), webvpn configuration, it is possible to configure bookmarks with "vdi://" links to Citrix's or Vmware's Virtual Desktop Infrastructures, but we couldn't find any configuration resource (conf guide) on official Cisco site: if it is actually possible to integrate Vmware View Client into ASA 9.1 WebVpn solution?
View 1 Replies View RelatedAm currently running BT Voyager 2091 wireless ADSL router with BT Voyager 1055 wireless USB adapter. What system requirements does one need to upgrade to 802.11n. The OS is XP Pro x32 bit x86 based PC
View 1 Replies View RelatedWe have a 7604 chassis with the following equipments:
1. RSP720-3C-10GE
2. 7600-SIP-400
3. SPA-1X10GE-L-V2
We would like our SPA to support XFP transceiver having part number XFP-10GZR-OC192LR.
Got a question regarding 2921 modules. Can I use VWIC2-2MFT-T1/E1 along with NM-HDV2-2T1/E1 on 2921 and what is the minimum requirements for IOS image?
As I understand, NM-HDV2-2T1/E1 is supported on 2921, however VWIC2-2MFT-T1/E1 is not, VWIC-2MFT-T1/E1 only. But VWIC-2MFT-T1/E1 is not supported on 2921.
I need to choose router for my network. I don't have any special need, besides Internet connection and DHCP for some guest clients.There are around 30 IP phones (static IP), 30 PCs (static IP), and 10 wireless APs (users get dynamic IP). Maximum load is 5 phones, 5 PCs and 20 phones/laptops connected via wi-fi.
I guess I should go for Cisco 800 series. Would model 861 be good or I will need 881 or even 891?
I have a Cisco SG500-52P along with an older SGE-2010P, am I correct that in order to stack they must be the same series?
View 1 Replies View RelatedWhat vmware i have to use to install cucm 7. vmware workstation 7 or vmware server or exsi 4 or 5. Any correct link to download and vmware config settings.
View 2 Replies View RelatedOne of our clients is going to install WCS on a Vmware machine and uninstall it from the physical server. He wants to know if he can use the same license or get another one; since he will get a new Mac address with the new VmWare machine.
View 1 Replies View Relatedis it possible to install cisco acs 5.4 on vmware 8 workstation ?
View 1 Replies View RelatedI'm currently trying to install the Cisco LMS 4.2 Appliance on a VMware vSphere 4.0 environment.I'm following the [URL]. I downloaded the Cisco_Prime_LAN_Management_Solution_4_2.iso and I started the server.I get this screen and I choose option 1:
View 3 Replies View RelatedI have just installed Cisco Prime LMS 4.1 from .ova file on a VMware architecture. My customer wants to know if the server is compatible with vmware tools.
View 7 Replies View RelatedWe have a scheduled office move where we are consolidating 2 remote offices into one. I’ve been asked to spec out the correct size UPS to support all of the network equipment for this new office.I went to the Cisco website and I see on the datasheet for the switches and router where they talk about the wattages and BTU’s but how can I go about deciphering from that information what my total wattage and BTU will be for each switch and router?What numbers should I be looking at? For instance, we have 3 3750 48 port PoE switches. So if I look at the datasheet for that switch they have 4 different columns, one for 100% throughput power consumption, one for 5% throughput, another one for 100% throughput for max PoE load and one for 5% throughput with 50% PoE loads?Is there a common method for deremining UPS requipments? For the switches I pretty sure I need to assume max PoE load in the event every port has a phone plugged into each port.
View 3 Replies View RelatedI am trying to set a little network in vmware (for do some testing on GP)in a vmware installed server2008 and win7 both are in one team Both has only one network adapter which is set to LAN1 Segment Both can ping each other Installed AD and configured DNS configured dhcp with scope 192.168.2.100 to 192.168.2.200 Set domain - [URL]Assign static to server 2008 192.168.2.101 Windows 7 can connect to domain no problem both machine got no external connectivity means cant open any webpage Do i need to add another network adapter in server2008 and set as NAT so it can connect to external network as well Can i set static IP address to 192.168.2.2 to server2008 or its has to be only within the loop basically need to setup a netwrok within a team that should be able to connect internally and externally as well ( Wont be able to connect to my host machine as need to set up VLAN for that but atleast access to internet) So wt type of vmware connection should i use
Host
NAt
LAN segment
or custom
And how many network adapter i need in each machine and which connect to which one?
If I have linux or another machine inside of a VM and I perform tasks across the network, does any of the packets ever expose my hardware MAC address?
View 2 Replies View RelatedI was planning to buy 7204 VXR for my site's router for the following requirements:
- support for ATM, Serial, ISDN
- support for 3 10/100/1000 ethernet interface
- support for 2 WAN interface
However, I realized that the 7200 series will not be available for sale after September of this year!! Any "reasonable" replacement for 7204 VXR that meets the above requirements?
To check if this is enough to built point-point MPLS between 2811 abd 3745Maybe some other technology should to be used for point-to-point connection?Basically, there should be transparent connection between routers.Also, it's possible to use ISP routers as MPLS endpoints for MPLS, so seems just etherenet connection required
View 7 Replies View RelatedWe implemented WLC 5508 software version 7.3, with 8 Aironet devices, most of them are AIR-LAP1131AG-E-K9, and two AIR-LAP1242AG-E-K9.I could really have benefits of VLAN select feature, but I noticed that it's not working like it should. Two interfaces are in Interface group, but from 45 clients only few of them has IP address from one subnet, others have from second sub.I see requirements for this to work is 32 MB of flash on LWAP devices..I only have 16 MB.. upgrade of flash on devices or something ?
View 12 Replies View RelatedI have a pair of 6509-E Switches running VS-720 Supervisors. We are planning to add Ace Module onto the 6509-E. Will IP Base Image suffice the requirement? Will Ace Module work with only IP Base Image?
View 1 Replies View Related