is there any way to interact with wan port like LAN?i have connected a rocket m5 as a bridge to my Dir-615 wan port but i cant see the AirOS login page (rocket m5 configuration page) nor brige's ip address on my LAN...is there any way to interact with the ip address that connected to wan port?
View 1 RepliesI've got three Cisco 1721's and a 2610, two of the 1721's are 32f's, the other one is a bit older but is still the same model. The two Cisco 1721 32f's have 1-dsu-t1-v2 wics in them, and the older 1721 has a 1-dsu-t1 wic in it. Now no matter how i have configured it the old t1 wic will not talk to the v2 wic. I've tried putting the old wic into a 1721 32f and it doesn't work at all!
What i have working:
router DCE (1721 32f with v2 wic) can talk to router DTE (1721 32f with v2 wic) no problem with this configuration.
Router DCE:
-service-module t1 clock source internal
-service-module t1 data-coding normal
[ code].....
Router DTE:
-service-module t1 clock source line
-service-module t1 data-coding normal
[ code]....
Router OLD (1721 with v2 wic) can talk to router DTE (1721 32f with v2 wic) no problem with same config. What doesn't work: Any router with 1-dsu-t1 (old) wic to router DTE (1721 32f with v2 wic). again same configuration as before, so whats going on that i cant get this to work? Is the old t1 wic not compatible with the new t1 wic?
Wan goes down when transferring files between pcs connected to the lan port.It looks like it's running out of resources or something. Passing more than 10GB of data to other pc is a pain in the ass because nobody else can access internet (lan and wireless clients).Filled a support request in local dlink site. No response so far.
Model Dir-600 B2
Firmware 2.05
2 pcs transferring lan data.3rd pc (doing nothing) can't access router config at 192.168.0.1.
During an installation, we plugged a Ruckus wireless bridge (powered by a PoE injector) into G0/0 on the 1941. The port status remained down/down. We then tried connecting it to G0/1. Again, the port status remained down/down. We took another wireless bridge, plugged it into G0/0 and the port changed to up/up status within a few seconds. The same happened when connected to G0/1. Both ports are have speed/duplex set to auto/auto.We took the cable from the first wireless bridge and connected it a 3550 switch, the FastEthernet port went up/up. We then took the cable and connected it to a switchport card (HWIC-4ESW) that was installed in the 1941 router. The port came up/up.We connected to wireless bridge back to G0/0 in the 1941 and manually set the speed/duplex to 1000/full. The link light on the router became illuminated after a few seconds but no console message was displayed (nor did any events appear in the log) and a "show int g0/0" showed the port status as down/down. This was could not be duplicated as this only happened one time The wireless bridges sit atop of a water tower and are connected each via a shielded ethernet cable. The cable that we're having trouble with is cat5e STP and about 310feet in length. I should note that we have not yet swapped the PoE injector but it seams to be functioning properly as power is getting to the wireless bridge and its accessible. Also because if the wireless bridge for some reason didn't come back up after a power cycle it would potentially mean climbing the tower to perform a hard reset. We tried another 1941 with same results however we have not tried another router model to rule out a potential platform issue. Can you recommend any troubleshooting steps to determine why the port status of the gig interfaces on the 1941 don't come up?
View 4 Replies View RelatedI am facing low relaiblity issue in one of the ethernet port even no link is connected to that port.
Router model : cisco 3660
IOS - c3660-ik8s-mz.122-24a.bin
Ethernet1/2 is up, line protocol is down
Hardware is AmdP2, address is 0007.85fb.c312 (bia 0007.85fb.c312)
MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec,
[Code]...
I have the DIR-655, Rev. B running 2.07NA firmware, and have a strange problem with my wired clients. I have my primary computer/desktop PC connected via wired connection. I also have several wireless clients (laptop, iPad, iPhones, etc.). All have been performing normally. However, in December I connected a wired weather internet bridge to another ethernet port on the DIR-655.
It functions as it is supposed to, and all other connected devices do as well. But here's the problem - whenever I use the desktop PC (the only other wired connection) to do anything on the internet (mostly just web browsing ... I don't stream media from the internet on it, I don't do torrents....nothing out of the ordinary, and nothing really of high bandwidth), the wired weather bridge cannot communicate with its associated website. This continues as long as I'm using the desktop PC. When I stop using the desktop, the weather bridge resumes normally.
I have researched the weather bridge, and it is simply doing POST transactions (or so I'm told) to the website listening to it. It doesn't wait for acknowledgements or anything...just keeps POSTing updates. I tried reserving an IP for the weather bridge and the desktop, enabling QoS, and prioritizing the weather bridge (100 vs. desktop at 125), but it didn't work. I've tried moving the weather bridge into the DMZ. I'm totally baffled how just using the desktop to browse the internet could completely block the traffic from the weather bridge.
On the weather bridge support site, they suggested that I insure I'm not connected in gigabit speeds from my computer to the router, because in the past that has been known to cause issues on clients not running that speed, but I don't think my desktop is connected in that fashion. According to the settings, it can do 10 or 100, full or half. I have it set to AUTO.
Region : Philippines
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 120810 Rel.44064n
I have a PROLiNK H5001N ADSL Wireless Modem using bridge mode to my TL-WDR4300. I login to my ISP using the TL-WDR4300 with secondary connection to my modem so that I can open the modem setup page.
1.) My question is can the Prolink get DHCP address from the Wan Port of TL-WDR4300?
2.) Can I still use the Wifi of the modem to get internet?
3.) If I connect my ISP to Prolink then connect TL-WDR4300 thru static connection, will the NAT and Hardware NAT still work in the TL-WDR4300?
NOTE: the latest firmware built TL-WDR4300_V1_121225 seams to have internet connection lost problem after a few minutes. I reverted back to 3.12.23 and the problem is gone.
I've been using a WRT120N on a local area connection.The WRT120N acts as a gateway and also to connect to the PPOE connection, via a bridged adsl modem.I've noticed that the LAN port 1 was flashing although the network cable was disconnected from the physical port. I've restarted a few times but to no avail as well. Ever since that, I've noticed that connection through cable are unstable and hard.Now, I'm not able to reset or upgrade the router's firmware.Is there any other way to be done so that I can get this router working as normal again.
View 6 Replies View RelatedIs it possible to create a service which will forward public port 9010 to an internal IP address with port 23?First of all, I do not like to open the public Telnet port to the inside so I would use another public port and second my ISP does not allow some public ports beneath port 80?
View 1 Replies View RelatedI have 2002 dell not sure that's relevant but I have Verizon as my Internet provider and after I downloaded an ip address hider it seems that I no longer have an ip address after I turned off my computer and turned it back on and can't load any Internet page. I've tried doing ipconfig /all and nothing comes up
View 9 Replies View RelatedI recently switched routers to the DIR-615 and I'm trying to troubleshoot why one of our laptops keeps losing the IP address and gets a self-assigned IP address. I see the following messages in the log, I am wondering if the reason codes are listed and explained somewhere? I tried searching the manual but could not find any information.
View 9 Replies View RelatedIt says im connected to the internet but I cannot get any websites.I aquired ip address fine my laptop connects,right now im on my lap top.like I said ip address and gateway,says im connected but im using a public network.
View 3 Replies View Relatedat my home i have a d-link router i have configure the modem to set it to be the same ip address in my old file server ip..and now my wifi can't auto connect for my phone and laptop..they has to insert a static ip address to connect the wifi...
View 14 Replies View RelatedI'm trying to configure a 3com 5500 switch with default ports for each vlan.The default ports are connected to IPS/IDS and do not have an IP address. I have a trunked esx host coming in and want to send traffic to specific ports based on vlan id - one port per vlan (10 total). Right now all I'm getting on the ips/ids is stp and arp traffic.
View 2 Replies View RelatedIf i need to know others IP address of internet connected computer, what would be the better and best steps to be done.
View 2 Replies View RelatedHow to track all the MAC address of all the modems connected to a network .
View 2 Replies View RelatedCan an ip address be NAT'ed to an ip address on a PIX 515 which isn't an ip address of a network directly connected to an interface on the PIX?
Specifically, can a host with an ip address of 150.140.102.3/26 which is connected to a network whose PIX firewall interface is 150.140.102.1/26 be NAT'ed to an ip address of 150.90.70.1/24 which is not a ip address of an interface that is directly connected to that same PIX 515?
I've attached a PDF depicting the network topology and describing the above.My first response to this question is that it can't be configured to do this, but need either a confirmation or correction to this.
i did a fresh install of windows Xp on my sisters old laptop i had to transfer the drivers for it from my computer via usb drive since she didnt know where the original discs for it where at. Anyways my problem is exactly as the title says, i was able to connect it to the wifi router it recieves and sends packets just no problem but i cannot get an ip address or subnet mask. i checked ipconfig /all and it shows 0.0.0.0 for both the address and subnet mask with the defualt gateway being nothing, i tried using ipconfig /renew and the doesnt work it just times out. the DHCP client has started and is runnig on automatic. I am using my computer to type this since the laptop does not work, i only know so much about networking i can get by with normal problems this is beyond me though. internet provider is AT&T the laptop connects via linksys mini pci card I ran the set up for the router still nothing and after runnig the internet setup in the control panel i was able to get it connected and send/recieve packets but still no ip and not able to use the internet at all.
View 11 Replies View RelatedServer 2008 has two Nics one connected to outside switch and has internet, other Nic is connected to local siwtches which has 20 systems connected locally but does not have internet. Local systems were getting IP from server, but there was not internet on the lan systems, I restarted the server and local systems lost IP address. earlier everyting was fine.
View 2 Replies View RelatedRegion : Italy
Model : TD-W8968
Hardware Version : V1
Firmwae Version : latest
ISP : telecom italia business on ipatm
How to Forward an external wan port like 49150 to lan ip on port 22?In the control pannel I can set only one port , and this port will be the same where the connection will be router to the lan ip ,therefore If I set the port 22 , the connection will be natted to the 22, but how to set a different external port to a specified different lan ip port?
Region : UnitedKingdom
Model : TD-W8970
Hardware Version : V1
Firmware Version : 0.6.0 0.11 v000c.0 Build 121203 Rel.46289n
ISP : Virgin Media
Is there any way of forwarding an external port to a different internal port on the TD-8970 ?I saw a question posed on an Australian forum implying that it might be provided in a later firmware release.Our TD- 8970 has replaced a previous NetGear WAG 320N which had this facility, and is useful to provide access to multiple machines without having to modify each individually to use a different port.
I have an Amilo Pa1510 (Windows XP) and I can connect to the router but not surfing (browser doesnt load any website). I have tried the commands "ping" to my IP address and it works but ping to the default gateway IP address doesnt work either.I am using the same wireless connection right now with my smartphone. I have downloaded an app that executes the ipconfig command in my Android. I have used the same gateway IP address in my laptop but it didnt work either. I have tried to set automatically the IP addresses in my laptop without success too. I have turned off and on both laptop and router and also checked in the system window that all the processes such as DHCP and DNS servers are automatic and enabled.
View 4 Replies View RelatedHOW do I find the password connected to my IP address on the Actiontec router m1424wr?
View 1 Replies View RelatedI have a PC with Windows 7 connected wirelessly to a EA3500 router. How do I change the IP address on my PC ?
View 6 Replies View Relatedhow do I MANUALLY assign ip address to devices connected to my n300
View 1 Replies View RelatedI am having an issue opening a port (4040) on the 655 for my Fedora-based subsonic server. Inside the LAN, I can see the device from other peer machines, so I am confident the port is open and listening. However, I can't seem to get to the machine-port from outside/internet.
I have tried Virtual Server and Port Forwarding with single port. The server has a stactic IP which I've included in the DHCP range and outside the range. I have a DSL connection (AT&T), modem only. I have updated firmware. I have exhausted the Subsonic community's knowledge, everything points to the router, but all the settings seem correct. What am I missing? Is if possible there is a defect in the router? (don't laugh). Is there a way to trace a request to that port to see where it is hanging?
(yes, I've STFA, but don't know what else to do).
Ok, so with my WLC2504 implementation, I use the 4 ports to physically segment my wireless networks. Here is my setup:
Port 1 (Management) - Internal IP so I can manage the WLC from our internal network (Untagged)
Port 2 - Connected to our core stack and tagged with VLAN 14
Port 1 and 2 are both connected to the same core stack
Port 3 - Connected to a RV016 Linksys which is connected to our fiber connection to the outside (Untagged) - External connection for laptops
Port 4 - Connected to a Linksys wireless router (with wireless disabled) (Untagged) - External connection for smartphones
The TAC engineer I talked to just told me that I can only have one untagged interface on the WLC. If they are physically connected to different switches, thus physically segmenting the network, should it matter?
The wireless works just fine. What I am having issues with is getting a client that is hard-wire connected to the RV016 to get a DHCP address from the WLC.
I want to setup wireless on laptop with USB Stick connected to usb port.
View 2 Replies View RelatedEverything in our small network worked until today when I had to manually reset the router. We run a application through a provider which requires that we view it from the same IP address for access. We have a statis IP assigned by our ISP solely for this purpose. For simplicity, lets us 23.11.23.176 as the statis assigned by our ISP and 23.11.23.175 as the gateway also assigned by our ISP. The application we need to browse requires that we use the 23.11.23.175 address else it is blocked from viewing. When we hard line into the modem, we are able to browse it fine. When I connect the CISCO router and do it wirelessly, it shows our address as 23.11.23.176 what are the required steps in order to set the CISCO router to use the Gateway address as the browsing IP for computers connected to it. We had set it up about a year ago, and i completely forgot how.
View 2 Replies View RelatedOk on my new PC,,OS is windows xp..I works fine..connect to pppoe and can surf internet perfectly.But on my old pc,,it can only succesfully connect to wan miniport pppoe but cant surf the internet..its OS is Windows Vista home Prem.The old pc was my first pc(notebook) and last time I used it was on 2009..it was using Atheros AR8131 PCI-E Gigabit Ethernet Controller connection and I forgot what modem I used..but now I bought TP-link TD-W8901G and I use for ADSL connection.My new pc works fine because it was setup proffesionaly by my friend..it also still needs Atheros AR8131 PCI-E Gigabit Ethernet Controller connection to connect ADSL Wan Miniport PPPoE..but I repaired my old pc too late..and he didnt configured it..so I setup myself..all the PPPoE adsl connections.And so its succesfully connected to WAN miniport PPPoE..but I can surf the internet..The old pc also needs Atheros AR8131 PCI-E Gigabit Ethernet Controller connection for me to connect ADSL Wan Miniport PPPoE..but all that was succesfull.
View 6 Replies View RelatedOne of our Cisco 6500's fitted with a WS-X6704-10GE line card is showing a large number of Rcv-Err's on port 3. The port is disabled and no optic is even plugged in.Upon clearing counters, after every refresh the counters increment by 131070 -- so 131070 > 262140 > 393210 and so on. Seems a little strange that the buffer is full when nothing is connected.
View 3 Replies View RelatedI have internet line came from my neighbor throught his hub directly connected to my laptop.. My problem is, i buy wireless ADSL model router but when i check the DSL line port its rj14 which i can not connect my RJ45 internet line. Addtional information, my wireless router have another 4 port LAN. Can i connect my internet line to LAN port,if it so how will i configure the router..
View 1 Replies View RelatedI need a small number of computers connected to the Internet through the E4200.E4200 must be connected to the switch via the LAN port.The basic network is a network of class A - 10.xxx/255.0.0.0.How do I do?E4200 can not enter a mask of 255.0.0.0.
View 1 Replies View Related