Linksys Wireless Router :: EA6500 Slows Modem Speed
Jan 26, 2013
I just installed my new EA6500 and everything works ok I think, Netflix across my PS3 is ok, laptop connects, and smartphones connect. The problem is that my Internet connection to my desktop (wired) PC is slow as mud. My ISP is a fiber optic provider and although I'm not sure exactly what my connection speeds are my Internet connection has always been blistering fast. With everything other than two smartphones turned off my desktops Internet access is slow. How to get my speed back and still use my new router?
View 2 Replies
ADVERTISEMENT
Apr 29, 2013
When I connect my modem directly to my computer I'm getting 27 MBPS speed. When I hook it up through my router, speed slows to 15 mbps.
View 2 Replies
View Related
Nov 9, 2009
I have a WRT160Nv3 router connected to a CM100 modem. I noticed that over time, perhaps a day or more, the connection speed slows. Usually, unplugging the router for a while then starting it up again restores the speed as per my cable company's speed test. I have called the cable company and their tech support reports a good signal to the house.
View 6 Replies
View Related
Jul 25, 2011
I can't get utube videos when I'm going through the router. I can get them if I'm on the modem only. The same applies to long PDFs, software updates, long virus definition updates, videos in general and graphics heavy websites. It just slows down eventually to a standstill and the download fails. As stated when the router is not connected the above items pop up or download reasonably quickly through the modem. We have moderate speed DSL.
View 1 Replies
View Related
Feb 18, 2013
I've a problem with the internet speed of my ADSL line(20Mega). Now I've the following components: D-link DSL-320 B (modem)+Cisco Linksys EA6500. If I start a Speed test the result its only 4M in download, while i remove the router and i connect my Pc directly to modem, the speed test results its 13-14M.
View 3 Replies
View Related
Nov 1, 2012
What's the point for two options, auto or 20 mhz only? there is no third option so if you choose auto its still 20 mhz am i right?BTW i had to change channel width to 20 mhz only because under auto the speed was horrible.
View 3 Replies
View Related
May 27, 2011
This issue started about 6 months ago. I have noticed the following issues:
1. I cannot download large files. It starts downloading then it stalls.
2. I cannot download videos on Youtube and other video site to stream the video. In [URL] the test shows 100% complete but the test keeps on running and upload speed goes down.while running the upload speed test on [URL] sometimes it cannot connect to server to upload the file. When it connects to the server I get error saying that it cannot read the file it uploaded.Had Comcast come out to take a look at the cable and they claim that it was the PC's fault and not the cables's fault. I have the cable coming out of the modem to a linksys router ( WRT54G), then to my PC. I connected the cable directly from the modem to the PC and still had the same proble.
I have the following:
System
Manufacturer: Velocity Micro
Model: Edge V420
Processor: Intel core 2 Quad CPU Q9550 @ 2.83 GHz
Memory(RAM): *.00 GB
[code]....
View 1 Replies
View Related
Sep 28, 2011
I'm using Cisco EPC3825 cable modem for my home network, and wondered a thing, that if I set up modem to work in router-mode, my real connection speed slows down to around 5-7Mt/s, when using modem in bridged mode, my connection speed is close to 15-20Mt/s. My serviceprovider provides 200/10M speed to my modem, and they've checked, that modem is working with 204/10M speed, and computers works also, if using modem in bridged-mode.
View 1 Replies
View Related
Jan 29, 2013
I have an EA6500 which obviously has 4 Gigabit ethernet ports for my home network, but I need a DSL modem to get it working.What's the maximum speed current modems can supply from the Internet to my router, is there such a thing as a Gigabit capable DSL modem these days or am I dreaming ? Is it possible to even get Gigabit dowload speeds via DSL or would I have to go cable to achieve something like that ?My main concern is I don't want to buy a modem that will slow down or 'throttle' the capabilities of the new router I've just purchased or have I got the wrong idea ?
View 7 Replies
View Related
Jan 19, 2013
I just picked up a EA6500 wireless router today and I am a bit disappointed. I paid $199 for this router because I was hoping to take advantage of of fast N speeds and the advanced features it offers.When I first logged in to set up the router, I saw an amber exclamation point with a note that read "Updating Linksys Smart Wi-Fi Service". When I put my password in I was met with a "Unexpected Error" message.Also, the firmware updater doesn't work. Now on to the more bothersome issue. Wireless speed is poor. I replaced a WRT160NL router with this one. On my old router using WPA2-Personal (AES) I would see speeds of ~300 Mbps. On my EA6500, I see 120 Mbps. I have checked and double checked all wireless and security settings and don't see anything that looks wrong.
View 9 Replies
View Related
Feb 15, 2013
When I try the Speed Test on my EA6500 I am getting the following message. "The license for this Speed Test has expired. Please contact the webmaster of this site to let them now.".
View 7 Replies
View Related
Apr 8, 2013
I recently purchased an EA6500 router to replace the crappy Westell 7550 AT&T provided me with. The 7550 was easily hooked up with two cords: the Ethernet cord into the computer and the Internet/data cable hooked into the DSL filter. I thought the EA6500 would have an easy installation, but it has not gone so smoothly. I hypothesize it's one of two problems - either the Internet/data cable is incompatible with the EA6500 (the cable works; I've re-tested it on the 7550), or it is because all instructions mention plugging the Internet/data cable into a modem's port while I do not have a modem. My Internet comes from a DSL filter attached to a telephone jack in the wall.
View 1 Replies
View Related
Apr 20, 2013
I Have BT Infinity and they are pushing 70mbps to my house ....i bought an EA6500 and i had real bad internet speed but amazing conection speed with my BT Home HUB3 ... 23Mbps with Cisco EA6500 and 68Mbps with my BT Home Hub3. I found out it was the Media Prioritization so just to be safe i reset my factory settings and made sure it was turned off. Just like magic i get the same now as the BT Home HUB3 .
View 1 Replies
View Related
Nov 28, 2012
192.168.100.1 is how I access my modem using the 4100, but since buying EA6500 I can no longer find the config screen. connect to there modem from the EA6500?
View 7 Replies
View Related
Sep 26, 2012
Attempting to get EA6500 working with TWC Motorola Surfboard SBV5220 modem, which has been working just fine for the last 2 years with a Linksys E3000 router. DHCP client in the EA6500 either doesn't ask for an IP address from the cable modem or the modem just isn't supplying one. With the E3000, you could see the IP address assigned by the cable modem and the primary and secondary DNS server addresses provided, and if the DHCP request didn't work, these addresses would be all zeroes. But, with the EA6500, I can't find an equivalent screen that shows these assignments, or zeroes when the DHCP request fails.
View 1 Replies
View Related
Apr 5, 2013
I cannot access my Motorola SB6141 cable modem status page at 192.168.100.1 thru the EA6500 router. I can bypass the router and can connect to the status page with no problem. Is there a setting to change or can I possibly do port forwarding to access it?
View 9 Replies
View Related
Mar 8, 2013
I have rather huge connection at home. DL speed 80Mb, UL speed 3Mb.When I connect my PC directly to modem and configure PPPoE connection, I get 81Mbits/sec. When I connect my old ASMAX $30 router, I get 78 Mbit/sek. And I find it OK.But when I connect my EA6500 I get 28 MBits/sec. Same result on wire as on wireless connection. Of course If I enable prioritisation, I get even less, 12-15 Mbits/sec.I tried already even configuration with ASMAX as wired router and EA6500 connected to its LAN port. It gives me 50Mbits/sec.
View 5 Replies
View Related
Dec 10, 2012
Recently I upgraded my Internet speed at the ISP from 10Mbps to 25Mbps and the problem is that I am measuring only 15Mbps using [URL]On the day when the tech came out to install the new DSL modem, he noticed the difference and as part of troubleshooting, he bypassed the Linksys router and voila the net speed measured 25Mbps using speedtest.net.So, why my Linksys WRVS4400N V1.1.13 acts like a bottleneck in this case? I didn't have this problem at the speed of 10Mbps. The upload speed is OK, it is 5Mbs with or without the DSL modem.
View 2 Replies
View Related
Feb 18, 2011
When I connect directly to my dsl modem, I am getting better than 5 megabits/sec. which is what I should be getting for download speed.When connected thru the router, I am getting about half of that.My wireless connection speed is 54 megabits/sec, so that is ok. I cannot get any connection when I hardwire the connection from the pc to the router too.
View 4 Replies
View Related
Jan 16, 2012
I am on a point to point internet connection that is rated at 2mbps. With my PC connected directly to the modem or through an old Airlink101 (model AR680W) router typical DL speeds are 1.9 to 2.4 mbps. However the Airlink router has to be reset 2 to 3 times per day.
I am trying to replace this router, however every router I've tried cuts the download speed in half (about 0.9 to 1.3 mbps). So far I've tried two Ultra Speed wireless N routers; two D-Link DIR 615's; and one Linksys E1200. When I talk to their tech support after testing they say that the routers must be faulty, but what are the odds of getting 5 bad routers from 3 different manufactures.
My IP does not know of any compatability issues with any routers.
View 3 Replies
View Related
Sep 1, 2012
I have an EA3500, I have 30 Mbps download when I connect my pc directly to the modem. When I add in the EA3500 router it drops to only 10 Mbps download on both wired and wireless devices.
View 9 Replies
View Related
Jan 4, 2013
My laptop connects and has excellent strength throughout my whole home but my internet slows down when i move only three meters away from my modem. I have been sent a new modem, changed wireless channels and troubleshooted with my network provider but still no luck.
View 8 Replies
View Related
Dec 21, 2011
I have a d-link dsl modem that reports it's getting the full 6 meg download speed from AT&T. I put the dsl modem in bridge mode so the E4200 will do the logon to AT&T with my credentials. If i do a speed check using CNET internet speed test, from both a desktop (wired 1gb card) and any laptop in the house (all draft n 2.4 or 5.0), it ranges anywhere from 3 meg to 4.3 meg. I have 6 cat-e ethernet cords everywhere. I do have 2 switches but have tried to unplug those to see if any difference
View 1 Replies
View Related
Aug 6, 2011
I am having a problem with my newly purchased Linksys E1000 router, I am having terribly slow network speeds while on that network.
Here are my network speeds with The e1000: (wireless) And here are the speeds with my old wrt54g: (Wireless) Here are the results directly hooked up to the modem: (wired)
I've tried setting the MTU to 1500, did a RMA with Linksys to see if it was a hardware problem, did a firmware update to the e1000, disabled DHCP and SPI, reseted my router and my modem....none of those things have worked
My ISP is comcast and I have a Arris TM502G modem
View 4 Replies
View Related
Jul 23, 2011
Ever since I started using iPads at the house I have had to reboot the router about once a week because the download speeds drops by approximately 90%. As soon as the reboot completes all is right with the world for about another week. During the course of the week, but not all at once, we will have 4 iPads, 3 iPhones, 2 laptops and one desktop(wired), a Verizon signal booster and house guests. I have updated the firmware.
View 1 Replies
View Related
Feb 22, 2011
I have FiOS and their supplied wireless router Actiontec #: MI424WR. I have equipment that uses the newer N signal so I purchased a Linksys E3000 Wireless-N Router. This is working great for my wireless home theater equipment but I am having problems with my wired speed. It has gone from 20 to 30 mbps to around 10 mbps. I have one of the LAN outputs on the Actiontec feeding the Linksys input, I have my computers plugged directly into the Linksys verses the Actiontec. This makes it easier to program the Linksys router. Since I am no longer using the wireless part of the Actiontec there really is no need to be plugged into it. Is there anything I can do get my speed back or will I have to plug the computer back into the Actiontec and move it every time I may need to make a change to the Linksys
View 3 Replies
View Related
Mar 17, 2012
Facing some troubles with my internet speeds, firstly the set-up is very simple, its just about 4 devices connected to a regular home router, 2 devices are connected via wireless and i am having trouble with my desktop PC.
Basically what keeps happening is that it fluctuates between 10Mb/s and as low as 0.8Mb/s, right now its at about 4Mb/s but i cant understand why this keeps happening, I am using a G wireless USB NIC and the laptop (the other wireless device) is fairly new so it should be an N wireless NIC, also it doesn't change my speed when it is being used for browsing and my neighbors wireless devices are also laptops with N cards. I believe that the router is G, having 3Mb/s at best which is far worse than normal.
View 3 Replies
View Related
Apr 19, 2010
When connecting wirelessly (5GHz) to the E3000 after a day or so the wireless connection starts loosing speed. I have Comcast and usually get 20-30 MB download connections. After a day or so I start to lose speed (down to 5MB) until I reboot the E3000. Then I resume 20-30MB download connections. My wired connections appear fine and don’t experience the slow down. I'm doing my speed test with [URL]
The wireless slow down seems similar to the old memory leak condition of old Windows OS’s. Called Cisco and they don’t have an idea. They had me change a few settings (channel info) but I’m pretty technical and don’t feel that will fix it.
View 9 Replies
View Related
Jul 13, 2011
Why my internet was so slow .90mbps. They got on my mac and changed the Ethernet setting to "manually" instead of "Automatic", then changed the speed to 10mbps instead of "autoselect". Now the internet is going at the 10mbps im supposed to be getting, but when i plug it into my router (wall>router>laptop) i get the .90mbps again. So do i how do i change the same setting on the router?
View 1 Replies
View Related
Jan 5, 2012
My WiFi is working, but only to about 20 feet then it slows down to almost nothing...
View 1 Replies
View Related
Aug 11, 2010
I have just bought an E3000 router when my old router died last week. I am having two problems:
1. The data rate slows down after a period of time (long message trail elsewhere)
2. I cannot see everything on the network.
I have several Win 7 computers, two win xp computers, three NAS devices (linux based), and a printer sitting on the network, along with two switches to cope with all the traffic (not to mention iPods, iphones etc.)With my old router, I couold see everything plugged into the network from my main Win 7 computer. (note: the win 7 network map does not always work, but the windows explorer window of the network always showed everything).With the E3000 router, I can only see 1 or 2 of the devices on the network. If I reboot the router, then sometimes all of the devices appear on the windows explorer window (sometimes not)I am running a workgroup (not a domain) and i am not using win 7's homegroup because that will not work with the non-win 7 devices.Is there a setting that will see all of the devices in Win 7 (either on the router or on the computers). I suspect it is a router issue as it worked with my old Zyxel router.
View 9 Replies
View Related
Mar 22, 2011
So I've had this problem before and normally I solve it by simply unplugging everything from my modem and router but ive tried that this time several times to no avail. The internet suddenly cut out one day and when I did my usual unplugging thing it came back unbearably slow.Right now I'm running off a motorola SB5100 Surboard modem and a linksys WRT54G2 router and its not my computer, everyone in the house is getting terrible speed.
View 10 Replies
View Related
Dec 28, 2010
I just discovered that my wireless download speeds are 5Mbps, compared to 16Mbps if my laptop is connected directly to the modem or wired through the router. Uploads are 2Mbps either way. I have a WRT54GS v.6 with firmware version v1.52.8 which I updated today, completed by setting factory default through the router webpage after I discovered this discrepancy. The firmware update did not improve the download speed appreciably, if at all.Should the wireless connection be that much slower than the wired connection through the router? If not, what sort of issues could I be having to account for this?
I did just replace my modem when I discovered I was having erratic speedtests and that corrected that problem. That is when I became aware of the wireless issue, so not sure how long that has been the case. I have Charter's 16/2 HSI, living in a sparsely populated area with solid internet service. There is no external nor internal interference on this 2.4Ghz band.
View 8 Replies
View Related
