Some tips and trick on how to configure and sg300 for intervlan routing.
I already have the switch set up for layer 3 I already set up multiple vlans and each vlan has a ip interface setup with the desired subnet I see the local routes set up in the static routing page.
I cannot seem to get from one subnet/vlan (I am using one subnet for each VLAN) to the next.
I setup switch in layer 3 mode. I have a access port in vlan 10 and a access port in vlan 20. I am able to ping form vlan 10 client to vlan20 default gateway (192.168.20.1) I am able to ping form vlan 20 client to vlan10 default gateway (192.168.10.1) However, I am unable to ping from vlan 10 to vlan 20 client. If both the ports are in same vlan, then clients are able to ping each other. Proxy Arp in enabled.
vlan 10 client ip info
192.168.10.10
255.255.254.
[Code].....
I have an issue with correctly configuring sg300 layer 3 switch behind ASA 5505 (incl Security Plus License) The setup is as follows:
CISCO SG300 is configured as a Layer 3 Switch
Native VLAN 1: ip address 192.168.1.254, default route (inside interface ASA 192.168.1.1)
Extra VLANs on Switch defined
VLAN 100 with 192.168.100.0/24, default gateway 192.168.100.254
VLAN 110 with 192.168.110.0/24, default gateway 192.168.110.254
VLAN 120 with 172.16.0.0/16, default gateway 172.16.10.254
From the different VLANS(100,110,120) I am able to connect to all devices in the other VLANS (except for Native VLAN 1; it's not pingable)From switch cli I can ping my firewall (192.168.1.1) and all other vlan gateways and vlan devices (VLAN1,100,110,120) From asa cli I can only ping my switch port (192.168.1.254), but no other devices in the other VLANs.
What do I need to change or setup in the switch or asa configuration in order for the other vlans to access the Internet through the ASA. I will not use the ASA as intervlan routing device, because the switch is doing htis for meI tried changing the asa int e0/1 into trunkport (uplink port on switch also), to allow all vlans, but as soon as I do that I cannot ping to 192.168.1.254 from ASA cli anymore.
I'm trying to get the following running.
I have 4 Subnets
VLAN 1 172.20.0.0/16 with the default GW 172.20.200.254
VLAN 10 192.168.10.0/24 with the default GW 192.168.10.2
VLAN 59 192.168.59.0/24 with the default GW 192.168.59.254
VLAN 130 192.168.130.0/24 with the default GW 192.168.130.254
[Code]....
With absolutly the same settings I did this with an HP E4200-12G L3 Switch (which is now doing the job) so there is no routing mistake in the other components.For me it looks like, the SG300 doesn't like to be NOT the default gateway.
I have two SG300 serie switches and two Gigabit connection between them. How do I configured these two links to work toghether like a one 2 Gigabit channel?
View 2 Replies View Relatedupgrading our small office network. We currently have about 75 employees with probably 125 devices on the network. I'd like to create about 10 vlans for the different departments and then configure intervlan routing as needed. Currently we have all unmanaged switches and it's just a huge broadcast storm on the network. We are upgrading our Cisco 800 router to an ASA5505 sec. Plus license. I need some recommendations on switches. Of course, this needs to be done as cheap as possible.... Is there a way to use the ASA to configure all the vlans and intervlan routing and access lists and use a cheaper switch to provide the access layer to hosts?
View 4 Replies View Relatedi have 2960 l2 switch connected to the ASA 5505. for some or the other reason i am not able to do intervlan communication. have done trunk mode on both ends on the switch as well as on the ASA and native vlan 1 allowed. the trunk is up up i am able to ping only the vlan 1 ip from the switch to the ASA for the vlan 2 i am not and similar for vlan 3.
config on the ASA
ASA Version 8.2(1)
!
hostname ciscoasa
[Code].....
how to configure SNMP on the Cisco SG300 switches? I have the SG300-10P. I am not fully familiar with the new command line interface on this device, it was easy on the IOS but finding it a nightmare on this one.
I put the following command in but it didnt work.
snmp-server view Interfaces interfaces included
snmp-server community ACB123 ro 10.x.x.x view default
I tried to follow the guidelines on the cisco website but thats all Web interface based, i can only access the switch remotely via CLI.
i purchased 300-28 how it config for stp and trunk
View 2 Replies View RelatedI'm trying to configure intervlan routing between a cisco 2801 router and HP/Amer switches. Using int fa0/1 and subinterfaces I was sure I had it configured correctly, but I cannot ping the default gateways when I place a host in a particular vlan. Below is what I have configured.
HP switch - port 9 connects to fa0/1 on 2801
ip default-gateway 10.1.100.1
trunk 9 Trk1 trunk
trunk 10 Trk2 trunk - to another switch
[code].....
I am using a 3750 as a default gateway for multiple Vlans on a few 2960 switches. The trunk lines are configured and working and I have assigned ip addresses to each of the Vlan interfaces on the 3750. My issue is that I can only ping the ip address on the Vlan interface of the 3750 if I have a working computer plugged directly into the Vlan on the 3750. I only have 3 vlans on the 3750 that have hosts directly connected (vlans 2, 10 and 40) the other vlans ( 20 and 70) don't have any clients plugged into them on the 3750 but the hosts reside on 2 different 2960s that connect via trunk ports. How do I keep the vlan interface on the 3750 switch pingable when I don't have hosts directly connected in that vlan on the 3750? (yes, I have enabled ip routing on the 3750)
View 5 Replies View Relatedconfigure Line Telnet on a Cisco SG300-10P switch.I am in config mode and enters line telnet,but when I do a show line,telnet still are disabled..
View 1 Replies View RelatedI have a Cisco SG300-20. I have read the documentation and cannot seem to locate the instructions for port forwarding. I need to forward TCP port 8088 to IP address 192.168.14.110 on the switch.
View 5 Replies View RelatedI have a Cisco SG300 small business switch and 541 APs. There are 2 VLANs in our network. One must be limited by bandwidth. How to configure vlan rate-limiting on SG300? And describe CIR & CBS.
View 1 Replies View Relatedwhy i can not found ip router setting by main menu? the sg300-28 can not support ip router command?mor informations,see my img. If sg300-28 can not support ip router command,what i can do it that communicate by multi-Vlan ?
View 2 Replies View RelatedI have a test setup of a C3750 stack as a core and some 2960's as access switches.[URL] - The switches at the bottom is the new network (VLANNED). The switches on the left is the current production network (10.1.1.0/24) From the C3750 to the router is a /30 network.
There will be 6 VLANs but at the moment I have one configured. VLAN50 - 10.5.1.0/24 From the C3750 I can ping my current production network, internet, other VLANs in the testsetup, ... Everything.From the C2960 I can ping other VLAN's, reach the gateway, reach the router, reacht the currenct production network. But I can't reach internet. I've configured "ip default-gateway 10.5.1.254" on the C2960. C3750 relevant config is down below.How is it that I can reach other networks connected to the router and not internet from the access switches? I'm just trying to ping 8.8.8.8.
!
ip routing
!
!
interface GigabitEthernet1/0/1
no switchport
ip address 172.16.1.2 255.255.255.252
[code]....
I am trying get inter vlan routing to work on a DF 300 - 24 port switch. I have an existing company network on 192.168.111.0 and want to create a vlan on 192.168.1.1 that can talk to 192.168.111.0. I have enabled layer 3 routing on the switch via console and also provided the ip routing command. I have the following VLAN's:
VLAN1 - Default 192.168.111.0
VLAN2 - 192.168.1.0
I have enabled DNS and provided my two DNS servers 192.168.111.82 & 192.168.111.212. I have set the VLAN1 interface to 192.168.111.217 and VLAN2 interface to 192.168.1.1.
Ports FE1 - FE15 are set to access ports and assigned to VLAN1 (untagged)
Ports FE16 - FE24 are set to access ports and assigned to VLAN2 (untagged)
I have set a default route for the switch to 0.0.0.0 0.0.0.0 192.168.111.254 (Draytek 2600 router). I have connected a computer (A) to VLAN1 port FE3 and a computer (B) to VLAN2 port FE16. I have set Computer A default gateway to 192.168.111.217 and its IP address to 192.168.111.94. I have set Computer B default gateway to 192.168.1.1 and IP to 192.168.1.2.
Computer A has access to Mdaemon, file server via network drives but no internet (cannot ping google) and can ping computer B and RDP onto computer B.
Computer B can ping computer A and RDP onto computer A but does not have access to the company network i.e MDaemon, file server etc. It also cannot access the internet.
From the console I can ping [URL]and all ip addresses in the company network i.e. 192.168.111.82 (DNS server). If I scan computer A wirh wireshark the internet starts working weird!
Configuration show below:
switch7c0a71#show run
vlan database
vlan 2
exit
voice vlan oui-table add 0001e3 Siemens_AG_phone________
voice vlan oui-table add 00036b Cisco_phone_____________
voice vlan oui-table add 00096e Avaya___________________
[code]....
I have my network with severals SG300 switches.I have one of them like my core switch working in layer 3 mode. With 2 vlans and vlan interfaces to each vlan.Everything is working ok.But now i have to connect one 3com unmanage switch that have host from vlan 1 and 2. How should i connect this switch to my Cisco sg300 switch?
[code]...
I'm looking to configure the QOS for VOIP on my network.I have a switch SG300 and several no Cisco VOIP phone. What are the parameters to be taken to implement the QOS?
What is the procedure for installing the QOS? I need to create a VLAN for the data and one for VOIP?I read in the quick start guide that there is auto-QOS for VOIP?This can be done from the GUI? what are the options to put?
I have a cisco L2 SG300-10p Managed switch . I want to configure one port as a turn but cant find the command Encapsulation dot1q . Its a poe switch i want to use for both internet and voip in separate vlans.
View 1 Replies View RelatedThese are our first switches and seems like GUI is lot different than the online. Out intervlan routing is o not working. I am absolutely sure that I setup the switch in L3 mode since it allows me to create mutiple interfaces. I am hoping that this GUI issue is related to interVLAN routing.
Below is the blog I started for InterVlan issue [URL]
This is the link for online simulator and what I see in its IP tab. I know this switch is not SG300. [URL]
This is what I see on our switch.
Our switch version
switchd64684#show version
SW version 1.1.0.73 ( date 19-Jun-2011 time 18:10:49 )
Boot version 1.0.0.4 ( date 08-Apr-2010 time 16:37:57 )
HW version V01
1) I have a Cisco SG300-28P. I plan to add a SG300-52. Would it be possible to manage the new switch through the SG300-28P web browser ?
2) There are 2 fans in the POE model SG300-28P. How many fans are they in the non POE switch SG300-52 ?
We have recently purchased a SG300 to break up our network which most consists of virtual machines via Bridged networking on network machines. I have created successfully Vlans and the physical machines are capable of communicating across the different subnets that I have created via the SG300 however the Virtual machines can no longer be reached.
View 2 Replies View RelatedCan I connect a single Cat5e cable between two SG300-28 and link them? If so what must I configure?
View 1 Replies View RelatedI have SG300-28P that I am using as layer-3 switch. Recently I ran in to SG300-52 switch and even though loading same firmware doesn't give me option to do layer-3 switching. For SG-300 I see options in GUI to create vlan interfaces under IP information section, while SG300-52 has IP information option only under the management section.let me know if these are 2 different hardware types and L3 is not possible on SG300-52. If its possible to enable L3 switching on SG300-52?
View 2 Replies View RelatedI have a connection on IP 192.168.1.21, Subnet 255.255.255.0 - this is on the default VLAN1 on the switch. I need to route this to IP 10.0.3.101, Subnet 255.255.252.0 - which is set up on VLAN2 on the switch. I have set the switch to Layer 3 via console.
how I setup this route? I am use the Browser based interface.
I have a project I am working on that will require routing over a MetroE circuit to connect a few sites together back to HQ. Although, I know this can be accomplished several ways, I have come up with a solution that I think will work, but would like you all's input as to whether this is adequate and if my thoughts on how to properly "organize" the network are right.
I have been working with the SG300 line in Layer 3 mode and have not had any issues in a test setup I have here in the office. Basically my thought is to have a single VLAN/subnet allocated for each physical site. That will handle the basic interoffice connectivity etc. I also have a need to prioritize voice/video traffic throughout the entire network. My plan was to create an additional VLAN/subnet to house the teleconferencing equipment. Thats pretty much the jist of the setup. My only question is how to properly prioritize the voice/video VLAN.
What does "ip routing" do on the CLI on the SG300? When I do this, I see it enables ip forwarding, but there is no mention of this in the CLI manual. I'm just trying to figure out what I would use this for, and if I should leave it enabled, or disable it. I have several different SG300 switches in L3 mode, and they are set up in a multi-vlan environment...
View 2 Replies View RelatedA brief background on the setup: I recently switched out my switch. It was a Cisco 3750 10/100 switch and I wanted to upgrade to Gig. The cost of a Gig+POE 3750 is too much to bite so I opted for the SG300. My router is a Cisco 891. Here is the setup:
Cisco 891:
two SVI's: vlan1 and vlan 100
Vlan1 = 10.0.1.1/24
[Code].....
With the 891+3750, I was able to add "ip pim sparse-dense-mode" on all the SVI's and hosts could join any multicast group, irregardless of which vlan the host was a member of.
Now I've changed switches, and I dont get the same love. I have the PIM statement on both SVI's on the 891, but Im unsure of what I need to configure on the SG300. I have enabled "Bridge multicast filtering" + "IGMP snooping". What can I do to get similar functionality using the SG300 + 891? I assume this is my lack of understanding IGMP in general, but was able to get away with it using the PIM statements on the 891+3750 stack.
I have a SG300-28P that is our Main VLAN Switch. Though the VLANs that I have on it are there mostly because of our Edge Router and our AP541Ns.We have the Following VLANs defined (Subnets Changed to conseal Piblic IPs) [code]
VLAN200 and VLAN201 come into Our Edge Router and out on a Single GE Port via VLAN Tagged to thje SG300.The SG 300 Splits them out to Untagged Ports and they are connected to Two Firewalls, each with a IP in the 200 and 201 Subnets. The AP510 has the VLAN200, VLAN192 and VLA101 tagged Subnets sent to it. The AP521 has three SSID, each associated with a Paticular VLAN.
This all works fine, though there are a few hidden flaws. Since all of the VLANs are present, both Internal and Public IPs, one could craft packets form one network and use the SG300 as its gateway to the other subnet and Gain Access. How can I isolate the Subnets, so that I can still use the SG300 as a Default Gateway for the 10.1.0.0/16 Network Make it so if someone from the 10.1.0.0/16 netwok accesses the 201.201.201.0/24 Subnet it uses the SG300's 0.0.0.0 0.0.0.0 default router (the Firewall IP) and not the VLAN InterfaceIf somone in the 201, 200, 192 Subnets uses the SG300 as a Gateway and tries to access a 10.1.0.0/16 address it gets blocked.
configure my new SG300-28P. When I have started the switch, I have specified a new password and enabled telnet in order to setup the switch in Layer 3 mode.
After a restart, the switch took its IP address from a DHCP server. When I try to set a static IP address (192.168.2.1), I receive the following error message: Duplicated IP interface on the same subnet.
The IP address 192.168.2.1 is not used by any device within the network. For information, the message doesn't appear when the switch is in Layer 2 mode.
why I can't change the IP address of default vlan in Layer 3 mode ? All I can do is set the IP address to static or dynamic.
For test purpose, I have added 2 vlans. But I wasn't able to route traffic between vlan. how to configure the switch to route traffic between vlan?
find below details informations about my VLANs.
- Default (VLAN ID 1)
IP Address : 192.168.2.1
Subnet : 255.255.255.0
[Code].....
I've seen lots of posts from people having problems routing traffic between two vlans with some complicated examples. Any simple step-by-step example for an SG300 switch (in layer 3 mode) to configure two vlans and sending traffic between the two vlans without an external router?
-VLAN1 10.10.10.0
-VLAN2 10.10.20.0
I've tried to do this through the GUI and can't seem to make it work. I'm missing something in the GUI.
I just purchased a SG300-10 switch and loaded the newest 1.27 firmware on it. Setup my VLANS and trunks but I have this weird issue. My setup:
I have the SG300-10 as my main switch and changed it over to L3 so it can be my main core in my small network. On port 1, vlan 200 is setup as my native PVID untagged and I have it set to trunk vlan's 210(LAN network), 220 (management vlan) tagged over to a Dell powerconnect 5224 24port switch. On port 1 of the Dell switch, I have it setup as a trunk there as well with the same setup (native PVID vlan set to 200 untagged, trunking 210 and 220 tagged).