we are trying to configure the vpn with our provider we are on Asa and the use Checkpoint , vpn seem to be established on phase 1 and phase 2 too.bur when i send ping packets seem to los on tunnel and other side do not see them.Asa is after a onother firewall and outside interface of this asa is nated on this perimeter firewall.
View 5 RepliesI have set up a VPN tunnel using pre-shared keys between my ASA5505 and a Checkpoint firewall (another company).
I can initiate the tunnel from my side, but they cannot open it from their side. We get Phase2 failures.
The other company is saying:
"Your ASA is expecting my CheckPoint to negotiate the phase 2 timeouts in both seconds and kilobytes. Enabling kilobyte timeouts is not something that is currently realistically feasible on my side, so I ask that you disable/turn off kilobyte timeouts on your side"
However, I do not have a kilobyte timeout specified in the security association for the tunnel, only a seconds.
Is there a hidden default setting I have to turn off? If so, how do I do this?
I have a problem with a L2L VPN between ASA and Checkpoint R71 VPN I can ping it up to the network that is behind the checkpoint but they can not make me pin.
View 3 Replies View RelatedI am trying to get a simple IPSEC VPN between a Cisco 800 router and a CheckPoint firewall.The Phase 1 negotiation is working fine.
View 1 Replies View RelatedI have 5 static public IP addresses at my disposal. A checkpoint firewall with VPN access provides remote access for mobile users. How would I go about integrating the ASA 5505 SSL VPN into this network so some mobile users could continue using the checkpoint VPN client while others could have SSL VPN remote access? Attached is a graphic of the network.
View 2 Replies View Relatedwhat's required for the migration from Checkpoint R75-20 Splat install to the Cisco ASA firewall, links to documentation - step-by-step.
View 3 Replies View RelatedI have an ASA running 8.4(2) code.
I have been trying to get a VPN tunnel established between this device and a Checkpoint R70 firewall, but have been getting nowehere.
The settings are:
Encap: ESP
Encryption: AES256
Hash: SHA1
DH: Group 2 (1024)
Authentication: pre-share
lifetime: 1440 min / 4096000 KB
I can open the tunnel from the ASA to the Checkpoint, but the Checkpoint cannot open a tunnel with the ASA. It looked like the issue originally was the KB timout which was turned off on the Checkpoint side. They have since added that (4096000), but we are getting Phase2 failures.
How to create a tunnel between an ASA running 8.4(2) and a Checkpoint R70?
I am beginning to think that I have incompatible systems Is it a PFS issue? If so, how do I enable that in the policy section?
I want the vpn device for about 320 users
View 2 Replies View RelatedOur firewall expert has gone off on long term illness leave and I am trying to pick up the pieces :-(
We have an ASA 5520 (local office) talking to another ASA (remote office) via a VPN Tunnel.
My 1st problem is that I cannot ping from my inside network (local) to the outside interface of my remote ASA.
My 2nd is that I have debug enabled on my rules but am not logging anything.
how to configure ACS 5.2 for device administration of Checkpoint firewalls and security management servers?
View 4 Replies View RelatedWe are setting up a vpn between a cisco RV082 and a checkpoint device. From the Cisco device we have set up (as remote IP) the public IP 85.xxx.xxx.xxx but when we try to start the tunnel the VPN log (from RV082) report the error "INVALID_ID_INFORMATION" as described below.
Jun 11 11:38:41 2013 VPN Log (g2gips1) #894: sending encrypted notification INVALID_ID_INFORMATION to 85.xxx.xxx.xxx:500
Jun 11 11:38:41 2013 VPN Log (g2gips1) #894: we require peer to have ID '85.xxx.xxx.xxx', but peer declares '10.yy.yy.yyy'
[code]....
The IP 10.yy.yy.yyy. reported in the log is the natted ip of the Checkpoint device.
I am working on a project to migrate a single Checkpoint firewall over to a single ASA 5510, no VPN, just firewall. The checkpoint firewall has 8 physical interface so the ASA 5510 also support physical 8 interfaces so thiw will be a one-to-one swap. At the moment, I don't have an ASA 5510 to test my theory so I am going to throw it out here. The checkpoint firewall is a SPLAT running on an powerfull IBM Server with 8 CPU dual cores with 32GB of RAM and it has 1200 rules with over 120,000 objects with some of the crazy NATs but it works so we will just leave it at that. There are not that much traffics going across the firewall so there are no need to put in an ASA 5585
I use the cisco conversion tool to do the policy conversion from Checkpoint to Cisco, I get about 1.5 million lines in the configuration. A lot of it has to do with Checkpoint having no concept of interface security level while ASA does. I am sure I can optimize it to cut down the number of lines in the configuration; however, that is not my main concern at the moment. The customer goal is that at the time when cutover from Checkpoint to Cisco ASA, they want everything to be perfect, meaning that it will work like magic.
My question is that can the ASA 5510 handle 1.5 million lines of configuration? Are there any limitations on this? I know there are limitations with FWSM but since I don't have an 5510 to test.
Running EIGRP on network. Hub router connects to remote router via EIGRP and then I have 2 static routes getting traffic to the switch behind the checkpoint firewall(Edge-1 UTM). Some switches I can access while others I cannot.
View 1 Replies View RelatedI am trying to migrate checkpoint configs to ASA 5585 using SCT tool, this tool asking me to feed it *.W file from checkpoint which is suppose to be a rule definition file on CP, but I cant find it
View 14 Replies View RelatedI have configured SSL-clientless vpn on asa5520(8.2-asdm-6.4)It is working.Only problem is how to add pcs to the vpn.That mean like someone need to access pcs via vpn.Servers with url can add without any problem.is there anyway to add pc/servers with ip addresses?
View 2 Replies View RelatedI'm trying to use a 5520 to test something but the bandwidth seems pretty low for the product I'm testing over it. Can anyone tell me if there is a bandwidth limitation by default? I'm seeing 1.5mb/s average with spikes to 6mb/s or so. On the ASA5550 I was seeing usage up to 80mb/s.
View 5 Replies View RelatedI'm trying to setup the SSL VPN portal:When I connect via HTTPS to the ASA5520 outside interface I get the login prompt and after successfully login it takes me directly to the Anyconnect client download (starts Anyconnect immediately) even though in the group policy is configured to not prompt the use to chose the post login and the post login is ste to go to Clientless SSL VPN Portal?
View 7 Replies View RelatedWe have a several SonicWall TZ 190 establishing VPN tunnels with a ASA5520. Pericodically random VPN tunnels will drop and can not re-establish a connection. In order to re-establish the dropped VPN tunnel, our firewall folks manually drop all VPN tunnels connected to the ASA (they use to physically power cycle the ASA). They claim this is the only way to resolve the problem and since the SonicWall Life Time seconds for Phase 1 and 2 are set to 28800, they reset the tunnels every 8 hours. Additionally, they claim that SonicWall IPSEC is different that Cisco IPSEC which is the main problem. Hence they are requesting a SONICWAll VPN concentrator..
View 4 Replies View RelatedI have a Cisco ASA5520 that we are going to use to allow users to connect to our network via the Anyconnect client, I have authentication set up to validate against AD via LDAP, but was wondering if there were any way to set up the profile to check the PC before they log in....we do not want users using their home PCs to attach to our corporate network, only PCs that were issued to them by the company. Nothing is jumping out at me in the config, we are running some fairly old sofware on the boxes (ASA - v8.2(2), Anyconnect - v2.5.3046) I plan on upgrading the Anyconnect to v3.1 but will probably need to keep running the 8.2(2) version on the ASA due to support issues.
View 2 Replies View RelatedI have a asa5520 with five Internet IP.One for the internet interface and the others are static maped to dmz hosts. It runs rightly until yesterday.Now it will lose the connection to the gateway many times everyday and the dmz hosts can not connect to internet any time. configuration(simplified):
!
interface GigabitEthernet0/0
nameif internet
security-level 0
[Code]....
I called ISP to check,when ISP clear their router's ARP, the asa will lose the connection at the same time and then the ISP's router couldn't learn the ASA's MAC. After I 'clear arp' manually,The ISP's router can learn the ASA's MAC and the connection recovered,but the DMZ's cann't access internet still (of course,There is no problem between DMZ and ASA ,I ping the internet gateway from DMZ host and can not get any reply.).
I have a location where I have 2 WAN links, but without a dynamic routing protocol in between. I want to implement a kind of hub to 2 spokes VPN. But the spokes will actualy be on one single ASA firewall, each spoke on a different interface. One hub-spoke will be primary, the other one the secondary. When the WAN link for the primary VPN fails the secondary should be started on the hub to the other spoke.
View 1 Replies View RelatedWe have 2 x ASA5520 and I upgraded this to 8.2.2 last year, I see 8.2.5 and now 8.4 is out. If we are having no issues, is it best just to leave it as it is? I can see a couple of features I may find useful in 8.2.5, but 8.4 seems like a huge jump and a risky one too.
View 1 Replies View RelatedI have a problem with RME 4.2 from CWLMS 3.1. I have configured SSH in my asa 5520 device but RME can't get the configuration file. I ran a job to sync archive but i get this message error:
*** Device Details for ASA_5520_VOZ_01 *** Protocol ==> Unknown / Not Applicable Selected Protocols with order ==> Telnet,TFTP,SSH Execution Result: CM0062 Polling ASA_5520_VOZ_01 for changes to configuration. CM00 Polling not supported on
[Code].....
I have one firewall ASA5520, are very slow
View 3 Replies View RelatedI have a cisco 3750 switch connected to the ASA5520 which is connected to the internet
LAN ----> Catalyst -----> ASA5520 ------> INTERNET
10.1.4.0 ---10.0.0.1 ----10.0.0.2 ------- 203.98.227.3
On my switch I have VLANs configured. From the 10.1.4.0 network, I'm able to ping switch gateway. I can ping insde of ASA .. See my ASA config below. I have allowed http and dns traffic outside but cannot browse internet from the 10.1.4.0 network.
interface GigabitEthernet0/0
nameif outside
security-level 0
ip address 203.98.227.254 255.255.255.0
!
interface GigabitEthernet0/1
[code]....
I am trying to introduce an ASA5520 to my network based on the following diagram: ISP Internet ------> ASA5520 ------- > Cisco Router ------> LAN. The problem is I cannot ping the ASA from the LAN. I can ping it from inside the router. I already allow ICMP within ASA. If i remove the cisco router and replace it by a swich, I can ping the ASA with NO problem.
View 5 Replies View RelatedWe want to use ASA5520 but both Firewall have different CPU. One has CPU Pentium 4 2400 MHz and another has Pentium 4 Celeron 2000 MHz. Can it be configured for replica / failover?
View 5 Replies View RelatedWe have 2 firewalls on PIX facing the Internet and connected to interface e1 (behind it) an ASA version 8.3 Both the PIX (Firewall facing) and the ASA are on the same subnet.
By using Routing statements and statics I have been able to reroute specific traffic to the ASA5520 version 8.3 Now I need to inverse the 2 devices. The ASA5520 will be facing the Internet and the PIX will be behind it.Unfortunately the ASA5520 is refusing to route the traffic to the PIX. The access-lists are open accordingly and a NAT on the ASA has been created.
i have my router connected to ISP then my router directly connected to my ASA5520....i use also ASA5520 as my DHCP Server and i was wondering with the DHCP Server function of ASA 5520 because if i use the ASA 5520 LAN ip ...all workstation will not be able to browse anything from the internet unless i use my ISP DNS IP which they gave me?
View 3 Replies View RelatedGet the following log message on secondary ASA console output when turning on the ASA failover function?
"Mate's service module (CSC SSM 6.6.1125.0) on slot 1 is different from mine (CSC SSM 6.6.1125.0)"
After that the secondary cannot join as a failover unit and shows in disabled status.We have the same model ASA & CSC module and each pair of them are in same firmware (CSC 6.6.1125.0 with ASA5520 8.4(4)1), when I shutdown both the csc modules, the ASA failover works fine.
I am using a squid proxy behind an ASA5520 firewall to collect the users to the internet. Squid is just necessary to log what is going on in order to find a quick solution when the internet slows down.
Considering that I have unlimited licenses and I would like to get rid of squid, I wonder if the ASA has some functionalities to track which websites are being used and how much traffic is generated. If there is not, I would like to know if Cisco offers a good product to replace Squid.
I have installed and setup cisco anyconnect on a win2008 server. It is able to authenticate successfully but upon trying to establish the vpn connection to the asa5520, it shows "unable to establish vpn". Other servers and pc from the same remote site is able to establish the vpn.
View 1 Replies View RelatedUpgraded an ASA5520 from 7.x to 8.4 in one step? Release notes for 8.4 state that you can "...upgrade from any previous release directly to 8.4..." I've read the previous version release notes and see the various changes in NAT etc that 8.3 made.
View 3 Replies View Related