Cisco VPN :: 800 Router To CheckPoint IPSEC VPN
Jul 15, 2012I am trying to get a simple IPSEC VPN between a Cisco 800 router and a CheckPoint firewall.The Phase 1 negotiation is working fine.
View 1 Replies
ADVERTISEMENT
Cisco VPN :: For VPN Between ASA5520 And Checkpoint R55
May 16, 2013we are trying to configure the vpn with our provider we are on Asa and the use Checkpoint , vpn seem to be established on phase 1 and phase 2 too.bur when i send ping packets seem to los on tunnel and other side do not see them.Asa is after a onother firewall and outside interface of this asa is nated on this perimeter firewall.
View 5 Replies View RelatedCisco VPN :: VPN Between ASA 5505 And Checkpoint
Dec 6, 2011I have set up a VPN tunnel using pre-shared keys between my ASA5505 and a Checkpoint firewall (another company).
I can initiate the tunnel from my side, but they cannot open it from their side. We get Phase2 failures.
The other company is saying:
"Your ASA is expecting my CheckPoint to negotiate the phase 2 timeouts in both seconds and kilobytes. Enabling kilobyte timeouts is not something that is currently realistically feasible on my side, so I ask that you disable/turn off kilobyte timeouts on your side"
However, I do not have a kilobyte timeout specified in the security association for the tunnel, only a seconds.
Is there a hidden default setting I have to turn off? If so, how do I do this?
Cisco VPN :: VPN L2L ASA Checkpoint R71 Cannot Make Pin
Feb 17, 2011I have a problem with a L2L VPN between ASA and Checkpoint R71 VPN I can ping it up to the network that is behind the checkpoint but they can not make me pin.
View 3 Replies View RelatedCisco Firewall :: Have Checkpoint But Want To Add ASA 5505 SSL VPN?
Dec 10, 2011I have 5 static public IP addresses at my disposal. A checkpoint firewall with VPN access provides remote access for mobile users. How would I go about integrating the ASA 5505 SSL VPN into this network so some mobile users could continue using the checkpoint VPN client while others could have SSL VPN remote access? Attached is a graphic of the network.
View 2 Replies View RelatedCisco Firewall :: R75-20 / Migrate From Checkpoint To ASA?
Sep 11, 2012what's required for the migration from Checkpoint R75-20 Splat install to the Cisco ASA firewall, links to documentation - step-by-step.
View 3 Replies View RelatedCisco VPN :: ASA Running 8.4(2) To Checkpoint R70 Tunnel
Dec 11, 2011I have an ASA running 8.4(2) code.
I have been trying to get a VPN tunnel established between this device and a Checkpoint R70 firewall, but have been getting nowehere.
The settings are:
Encap: ESP
Encryption: AES256
Hash: SHA1
DH: Group 2 (1024)
Authentication: pre-share
lifetime: 1440 min / 4096000 KB
I can open the tunnel from the ASA to the Checkpoint, but the Checkpoint cannot open a tunnel with the ASA. It looked like the issue originally was the KB timout which was turned off on the Checkpoint side. They have since added that (4096000), but we are getting Phase2 failures.
How to create a tunnel between an ASA running 8.4(2) and a Checkpoint R70?
I am beginning to think that I have incompatible systems Is it a PFS issue? If so, how do I enable that in the policy section?
Checkpoint Vpn Server For 500 Users
May 3, 2012I want the vpn device for about 320 users
View 2 Replies View RelatedCisco AAA/Identity/Nac :: Configure ACS 5.2 And Checkpoint For Firewall Admin
Aug 5, 2012how to configure ACS 5.2 for device administration of Checkpoint firewalls and security management servers?
View 4 Replies View RelatedCisco Routers :: Setting Up VPN Between RV082 And Checkpoint Device?
Jun 10, 2013We are setting up a vpn between a cisco RV082 and a checkpoint device. From the Cisco device we have set up (as remote IP) the public IP 85.xxx.xxx.xxx but when we try to start the tunnel the VPN log (from RV082) report the error "INVALID_ID_INFORMATION" as described below.
Jun 11 11:38:41 2013 VPN Log (g2gips1) #894: sending encrypted notification INVALID_ID_INFORMATION to 85.xxx.xxx.xxx:500
Jun 11 11:38:41 2013 VPN Log (g2gips1) #894: we require peer to have ID '85.xxx.xxx.xxx', but peer declares '10.yy.yy.yyy'
[code]....
The IP 10.yy.yy.yyy. reported in the log is the natted ip of the Checkpoint device.
Cisco Firewall :: ASA 5510 To Migrate Single Checkpoint
Dec 18, 2012I am working on a project to migrate a single Checkpoint firewall over to a single ASA 5510, no VPN, just firewall. The checkpoint firewall has 8 physical interface so the ASA 5510 also support physical 8 interfaces so thiw will be a one-to-one swap. At the moment, I don't have an ASA 5510 to test my theory so I am going to throw it out here. The checkpoint firewall is a SPLAT running on an powerfull IBM Server with 8 CPU dual cores with 32GB of RAM and it has 1200 rules with over 120,000 objects with some of the crazy NATs but it works so we will just leave it at that. There are not that much traffics going across the firewall so there are no need to put in an ASA 5585
I use the cisco conversion tool to do the policy conversion from Checkpoint to Cisco, I get about 1.5 million lines in the configuration. A lot of it has to do with Checkpoint having no concept of interface security level while ASA does. I am sure I can optimize it to cut down the number of lines in the configuration; however, that is not my main concern at the moment. The customer goal is that at the time when cutover from Checkpoint to Cisco ASA, they want everything to be perfect, meaning that it will work like magic.
My question is that can the ASA 5510 handle 1.5 million lines of configuration? Are there any limitations on this? I know there are limitations with FWSM but since I don't have an 5510 to test.
Routers / Switches :: Cannot Switch Behind Checkpoint Firewall
Mar 14, 2011Running EIGRP on network. Hub router connects to remote router via EIGRP and then I have 2 static routes getting traffic to the switch behind the checkpoint firewall(Edge-1 UTM). Some switches I can access while others I cannot.
View 1 Replies View RelatedCisco Firewall :: Migrate Checkpoint Configurations To ASA 5585 Using SCT Tool
Oct 28, 2011I am trying to migrate checkpoint configs to ASA 5585 using SCT tool, this tool asking me to feed it *.W file from checkpoint which is suppose to be a rule definition file on CP, but I cant find it
View 14 Replies View RelatedCisco Routers :: Can RV042G IPSec VPN Support Apple IOS IPSec VPN
Apr 29, 2013I tried any type of combination and just couldn't make it works. Only PPTP works well. Whether Apple iOS IPSec VPN is supported or not?
View 11 Replies View RelatedCisco VPN :: IPsec VPN On 871 Router
Sep 27, 2011I have a cisco 871 router and I have set up an IPsec vpn on it. I can connect to the vpn but once connected I can only ping the router (10.12.0.1) but nothing else on the network. I can access the router via ccp/telnet and from the router I can ping other machines on the network, so I know that they are connected, but I can't access them from the vpn connected machine. Also the vpn connected machine can't access the internet while connected to the VPN. How can I get computers that connect via the vpn to see other machines on the network, and how can they access the internet while connected to the vpn?
Here is the running config:
Building configuration...
Current configuration : 6760 bytes
version 12.4
no service pad
[Code]...
Cisco VPN :: 837 Router To ASA5510 IPsec VPN
Mar 19, 2012I have a 5510 running 8.42 code with multiple site to site tunnels coming into it. Sites vary from ASA 5505's, 1841 and 1921 routers which all work perfectly. That being said I think the ASA side is good. I have an 837 running 12.4 code, Cisco IOS Software, C837 Software (C837-K9O3SY6-M), Version 12.4(5b), I'm trying to configure it for site to site VPN back to the ASA. When I ping from the E0 interface I get the following debug output and nothing else. I've made a lot of changes to no avail in getting closer to a successful configuration. [code]
View 1 Replies View RelatedCisco :: L2L IPSec Tunnel - ASA To 3800 Router
Mar 3, 2011I have been struggling for a few days with getting site-to-site traffic working across a L2L IPSec tunnel. At this point, I have the tunnel up, and I see packets being decrypted on the correct IPSec SA's when I ping from a local network computer on the ASA side to a local network computer on the router side. I cannot ping from one side to the other, but those packets are getting through. We have another L2L tunnel that is from that ASA to another remote site's ASA, and that is functional. I have mirrored the configuration for ACLs, etc. from that site, so I believe that the issue is with the packets getting incorrectly translated by the NAT/NONAT statements/ACLs on the router side.
View 8 Replies View RelatedCisco WAN :: Adding IPSec To 1941 Router?
Jan 17, 2013I need to unlock IPSec to my 1941 router but I'm not sure which license(s) to purchase.
View 1 Replies View RelatedCisco VPN :: 2600 Router As IPSec Client
Jan 16, 2013Currently I'm using Cisco VPN client software to connect to a remote IPSec server on the workstations. I want to to configure IPSec client on Cisco 2600 router which connects to the remote IPSec server so the workstations can access VPN subnet without using VPN software. how to configure IPSec client on the router?
View 20 Replies View RelatedCisco VPN :: Need IPSEC VPN Capability On 1941W Router
Oct 27, 2011I recently purchased a 1941W Router and upgraded it to IOS15.2T. After upgrading I was disapointed to see that it didn't have IPSEC VPN capability. What do I have to do to get this support activated/installed on this device?
View 1 Replies View RelatedCisco VPN :: 1841 Router - How To Create IPSEC
Feb 10, 2011I need support regarding IPSEC - VPN in 1841 Router? I had purchsed 1841 Router and i dont know how to check, whether supported for VPN or not?
View 4 Replies View RelatedCisco VPN :: IPSEC Between Pix 515E And 1841 Router
Aug 4, 2012We have set up a site to site IPSEC VPN between a Pix 515E running 8.0 (4) and an 1841 using static IP addresses at both ends. We used CCP on the router and ASDM on the pix to build the initial tunnels. Now the site with the router is changing to a Dynamic IP address from the ISP so we have set up Dynamic DNS to update the dynamic IP address.
The problem we have is that ASDM will not allow us to set a domain as the peer address, it will only accept an IP address. We think the solution will be to remove the static Crypto Map and replace with a Dynamic Crypto map on the Pix side. Our questions are simply; is this the best solution? can we edit the original static list or is it better to delete and make a new dynamic crypto map? Is there a short cut to change the config in command line? This is a live network so just want to check before we make changes on live kit.
Cisco Firewall :: Make IPSec VPN Between ASA And 877 Router?
Jan 22, 2013I want to make ipsec vpn between ASA and Cisco 877 Router,crypto isakmp and crypto ipsec ACTIVE state its works fine but Cisco 877 can not ping ASA internet interface but can ping behind ASA PC,PC can ping 192.168.2.1 but Cisco877 can ping only behind ASA PC thats ip 172.20.1.18
Ex:
192.168.2.0(Cisco877) =====ASA(172.20.1.0)-------172.20.1.18 PC
ASA IP : 172.20.1.2.54
C877 IP 192.168.2.1
[code]....
Cisco VPN :: L2L IPSec Tunnel - ASA To 3800 Router?
Mar 2, 2011I have been struggling for a few days with getting site-to-site traffic working across a L2L IPSec tunnel. At this point, I have the tunnel up, and I see packets being decrypted on the correct IPSec SA's when I ping from a local network computer on the ASA side to a local network computer on the router side. I cannot ping from one side to the other, but those packets are getting through. We have another L2L tunnel that is from that ASA to another remote site's ASA, and that is functional. I have mirrored the configuration for ACLs, etc. from that site, so I believe that the issue is with the packets getting incorrectly translated by the NAT/NONAT statements/ACLs on the router side.
The ASA is: Cisco Adaptive Security Appliance Software Version 8.2(2)Hardware:
ASA5520, 512 MB RAM, CPU Pentium 4 Celeron 2000 MHz The router is:Cisco IOS Software, 3800 Software (C3845-ADVENTERPRISEK9_SNA-M), Version 12.4(20)YA3, RELEASE SOFTWARE (fc2) Router Config:!version 12.4!card type t1 0 0!no ip cef!ip multicast-routing no ipv6 cef!crypto isakmp policy 10 encr 3des authentication pre-share group 2crypto isakmp key xxxxxxx address nn.nn.12.130!crypto ipsec security-association lifetime seconds 86400!crypto ipsec transform-set 3DES-SHA esp-3des esp-sha-hmac !crypto map NOLA 11 ipsec-isakmp set peer nn.nn.12.130 set transform-set 3DES-SHA set pfs group2 match address VPN-ACL!controller T1 0/0/0 fdl both cablelength long 0db channel-group 1 timeslots 1-24!interface Loopback0 ip address 1.1.1.1 255.255.255.252 ip virtual-reassembly no ip route-cache crypto map NOLA!interface GigabitEthernet0/0 no ip address duplex auto speed auto media-type rj45!interface
[code]....
Cisco VPN :: 891 Router With Two Internet Feeds Both Doing IPSec VPN
Apr 12, 2012We are trying to setup a router with two internet feeds both of them doing IPSec VPNs back to a single peer...one of these VPNs is for VOICE traffic and the other is for DATA traffic...we have a default route set out one Internet feed which is the primary feed used for outbound browsing and the data vpn. The only other routes on this router are two static routes for the destination private subnets at the remote end but pointing to each feeds respective default gateway...I would have thought this would work, but only the data vpn is coming up and the voice seems to stay down due to not having a proper route?
If I set a static route for the remote peer out the voice internet feed, then the data vpn would drop...should I apply a policy based route on each of the inside interfaces, voice and data, setting the ip default next hop to their respective default gateways?
Cisco VPN :: Can 881 Router Create L2TP / IPsec Tunnel Via NAT
Feb 23, 2011Successfull in setting up an L2TP/IPsec tunnel through NAT-T against a Windows 2008/ R2 RRAS server? I am using an 881 router and the layout is someting like this:Client -> 881 -> NAT -> internet -> Windows 2008 RRAS.The tunnel goes form the 881 to the Windows server (not from the client...).
View 4 Replies View RelatedCisco VPN :: 1921 Router Q - How Many IPsec Tunnels Will It Support
Nov 8, 2011I need to know how many IPsec VPN tunnels one Cisco1921 can support reliably. Haven't had any luck sifting through documentation on the web.
View 2 Replies View RelatedCisco VPN :: 7301 - Multiple L2L IPSec Sources On One Router
Feb 4, 2012I'm trying to make a redundantish office/datacentre connection on the cheap. At the datacentre, we've got a 7301 (12.2(24)T5) and at the office we've got a Mikrotik RB1200 (5.12).The office router has two ADSL connections to two different ISPs, the datacentre router a single GigE to a colo provider. I'm trying to build an IPSec encrypted IPIP tunnel over each ADSL service to a separate loopback interface on the datacentre router, so I can run OSPF over the top for route exchange. I need to use two different loopbacks on the datacentre router so the office router can have a static route for each out each ISP ADSL. But I'm running into issues making encryption work on two different source addresses.Using the 'crypto map xxx local-address Loopback12' command, I can specify the outbound interface for one of the tunnels just fine, traffic moves as expected - while the other tunnel fails to encrypt. But is there a way of having two peers use two different local addresses, or applying two crypto maps to a single physical interface?
View 1 Replies View RelatedCisco WAN :: Configuring Remote Access IPSEC VPN In IOS Router 12.4T
Apr 20, 2011I am configuring Remote Access IPSEC VPN in IOS Router 12.4T.I am able to establish IPSEC VPN from VPN Client 4.0. But I am able to access all the LAN machines from this client connected.I want to restrict access to only one server in my LAN rather than accessing all the servers in Datacenter.For example
-Group FTP should be able to access only FTP Server with ip addess 10.1.1.21 on Port 21
-Group WEB should be able to access only WEB Server with ip address 10.1.1.80 on Port 80
Cisco WAN :: Does Router 887va K9 Support EIGRP And IPsec
May 12, 2013does a router Cisco 887 va k9 support EIGRP and IPsec ?
View 2 Replies View RelatedCisco VPN :: Configure Remote Vpn Ipsec Tunnel On 800 Router?
Mar 19, 2012how can you configure remote vpn ipsec tunnel on a Cisco 800 router?
View 12 Replies View RelatedCisco Switching/Routing :: Router 1941 But Can't Do Ipsec
Oct 10, 2012I did have a router cisco 1941 but can not do ipsec with it,i did take a smart net.
View 3 Replies View RelatedCisco Security :: Configuring IPSec VPN On 7200 Router
Apr 5, 2013I am facing a problem when configuring the ipsec vpn on my 7200 router. [code]
View 5 Replies View Related