Cisco WAN :: Configuring Remote Access IPSEC VPN In IOS Router 12.4T
Apr 20, 2011
I am configuring Remote Access IPSEC VPN in IOS Router 12.4T.I am able to establish IPSEC VPN from VPN Client 4.0. But I am able to access all the LAN machines from this client connected.I want to restrict access to only one server in my LAN rather than accessing all the servers in Datacenter.For example
-Group FTP should be able to access only FTP Server with ip addess 10.1.1.21 on Port 21
-Group WEB should be able to access only WEB Server with ip address 10.1.1.80 on Port 80
View 11 Replies
ADVERTISEMENT
Dec 10, 2012
I'm configuring remote access on my cisco 881. Protocol PPTP was chosen.I've configured PPTP VPN access on my router, but there's an issue with accessing my LAN. I can access my Internet connection and open web sites, but I'm not able to access my local resources.I can only Ping my router's interfaces (192.168.2.10, 79.104.14.62) and Internet resources. For example, I can not ping switch, directly attached to the router, with address of 192.168.2.2 and other hosts on LAN.
View 1 Replies
View Related
May 2, 2011
I’m configuring a L2TP IPSEC VPN on a 5505 asa so that windows 7 clients can natively connect. It connects correctly during Phase 1 and 2, but I can’t ping anything or access resources on the internal network. This is my first time working with an ASA.
Master# sh run
: Saved
:
ASA Version 8.2(2)
!
hostname Master
domain-name service.local
[code]....
View 2 Replies
View Related
Oct 3, 2011
I have Cisco ASA 5505 and i want to create vpn remote access ...l
so i created and connected to the vpn ...my problem is to reach my Local connection of 192.168.1.0 /24 i put the WAN Connection in the FA0/0 and put my LOCAL AREA CONNECITON into FA0/1 .. so how i can route or translate my connection , and using cisco ASDM 6.1 in GUI ,,,
View 1 Replies
View Related
Jul 12, 2011
I've read on Cisco AnyConnect 3.0 Q&A that it supports IPSec remote-access VPN: url...I've downloaded and installed AnyConnect 3.0.0629 Secure Mobility Client, but I'm not able to get IPSec VPN working. There's also no option to use PCF files from the previous Cisco IPSec VPN client. How to get IPSec VPN working on AnyConnect 3.0?
View 2 Replies
View Related
May 9, 2012
I'm running FW 1.2.4 and how to setup Remote Web Access over my IPSEC vpn tunnel. I would like to be able to remotely access these routers and make configuration changes from my main office but I cannot seem to figure out how to get it to work. If I try to access the internal router IP from across the VPN, I cannot. My VPN tunnel is up and operational and I can ping various devices across the tunnel but I cannot access the web management of the router.
View 4 Replies
View Related
Feb 6, 2011
I'm trying to set up remote access IPsec VPN on a pair of ASA 5540 without much success. I can connect with a client on the outside, and when I try to ping something on the inside I can see the ping requests reach the target but the answers don't come back to the VPN client. I've tried with different NAT rules without success.
View 3 Replies
View Related
Mar 7, 2011
Is there any documents that I can use to design an IPSEC remote access solution using 2 data centers . One data center is primary and other one is secondary. The VPN is terminated in ASA 5520. End users using cisco client.
View 6 Replies
View Related
Sep 28, 2011
We have two sites connect with an IPSec L2L VPN.
-Site A: 192.168.13.0/24
-Site B: 192.168.2.0/24
On both sites we have a ASA5505(Base license) to terminate the tunnel.On Site B we also got a remote access vpn to which we can connect using the vpn client.The lan2lan tunnel works fine and so the remote access vpn.Now i want to connect to Site A using my vpn client connected to Site B. [code] There are no vpn-filters or other special policys in place..If tried to ping from my vpn client to Site A while i was debugging ipsec 255 on site B: the asa matched the l2l-tunnel for traffic sourced from 192.168.25.x to 192.168.13.x but when im doing a show crypto ipsec sa detail there are no packets getting encrypted..so of course no packets reaching my asa on site a.
View 9 Replies
View Related
May 8, 2012
I have a newly aquired asa 5505 that I just set up to the bare minimum configurations. I followed a cisco paper on how to create a "remote access vpn" setup for ipsec. I can sucessfully connect and establish a VPN, but when I try to access an inside resource from the vpn address, the asa blocks it.
Specific error is: Code...
View 17 Replies
View Related
Apr 29, 2013
We have dns server(only Internal IP) inside our network, right now we have configured Remote Access VPN using Public IP and we connect it using the same Public IP. I need to use FQDN instead using Public IP. What is the configuration for this.
-Device : ASA 5520
-Configuration Type : IPSec
View 1 Replies
View Related
Jul 9, 2012
I had IPAD setup IPSEC Remote Access VPN to try to conect to ASA5540 and Cat65 VPN service module(V1).I works fine on Cat65 VPN service module using IPAD client, but it is fail on IPAD client connect to ASA5540.THe message should be "VPN server is no response".My laptop Cisco VPN client(Windows 7) works fine on both (Cat65 VPN module and ASA5540).There is any special setting for IPAD client on ASA5540 ? The IPAD ios version 5.1.1.The ASA5540 version 8.4(4)1 ADSM 6.4(9) The Cat65 version is quit old binding with CatOS V12.2 etc.
View 2 Replies
View Related
May 29, 2011
In my Cisco PIX-515E Version 6.3(5), I have a IPSec VPN tunnel and also to the same firewall home users connect through VPN client. I am unable to find a solution that allows my home users to connect to office network and again access the remote network through the IPSec tunnel.
View 1 Replies
View Related
Mar 16, 2012
I cannot get this to work properly and I've even had a Cisco engineer from TAC set-this up... and it literally broke my inside network. I have a VPN range of addresses..x.x.x.x on the Outside that needs access to a server on the Inside at y.y.y.y. HTTPS/443 connectivity. I need to NAT my VPN subnet/pool in order to talk to the inside host, as that host will not accept traffic from my VPN subnet, but obviously, will accept traffic from Inside my private network.
The Cisco tech entered the following static NAT statement to "fix" the problem - nat (outside,inside) source static VPN Inside-Network destination static Host-y.y.y.y Host-y.y.y.y For whatever reason, whenever this is configured on my ASA 5550 v8.3(2)25 the Inside interface starts proxy arping and assigns all IP addresses on my private network with the MAC address of the Inside interface.
The y.y.y.y is on a remote, routed network within my private, corporate MPLS network. My Inside private network (Inside-network shown in the static NAT above) is x.x.x.x. Not sure why this happens, but it kills my entire network and I have to jump through hoops to quiesce the network and get everything back to normal.I've tried to Dynamic-PAT/hide the VPN range behind the Inside interface through ASDM and that seems to do nothing.The NAT statement above will break my network. How to NAT this connection without killing my Inside network? Or, on how to properly hide my VPN subnet/pool behind my Inside interface and back to the VPN subnet/pool.
View 1 Replies
View Related
Apr 5, 2013
I am facing a problem when configuring the ipsec vpn on my 7200 router. [code]
View 5 Replies
View Related
Mar 6, 2011
We have ASA5500's deployed for remote access concentration.We use Cisco IPsec vpn client with a group policy the chacks for Network ICE BlackIce ersonal firewall.The powers-that-be wish to change to McAfee presonal Firewall ok..Now the Group Policy allows you to check for several pre- configured Firewalls, Cisco Integrated, Sygate, Zone Labs etc.So as McAfee are no listed then I am to assume we go for "Custom Firewall" and this is where I am struggling.To configure checking for a Custom Firewall I must have the Vendor ID and the Product ID.McAfee haven't the faintest idea what we're talking about when we ask them for these details.Or is there a way to extract them from the registry of a machine with the McAfee product installed?
View 3 Replies
View Related
Aug 28, 2012
I am configuring a vpn ipsec tunnel with cisco isr 2921 router and Watchguard edge 1250e. I have the watchguard configured so I just need to make sure I have everything setup on the cisco side. At this point, there is no communication as I am not sure if I configured it correctly. Should I do the crypto map on g 0/0 or dialer 1?
aaa new-model
!
!
!
!
!
!
!
aaa session-id common
!
!
no ipv6 cef
[code]......
View 4 Replies
View Related
Sep 12, 2012
We have two ASA 5500 series Firewalls running 8.4(1). One in New York, another in Atlanta.They are configured identically for simple IPSecV1 remote access for clients. Authentication is performed by an Radius server local to each site.
There are multiple IPSec Site-to-Site tunnels on these ASA's as well but those are not affected by the issues we're having.First, let me start with the famous last words, NOTHING WAS CHANGED.
All of a sudden, we were getting reports of remote users to the Atlanta ASA timing out when trying to bring up the tunnel. They would get prompted for their ID/Password, then nothing until it times out.Sames users going to the NY ASA are fine.After extensive troubleshooting, here is what I've discovered. Remote clients will authenticate fine to the Atlanta Firewall ONLY IF THEY ARE USING A WIRED CONNECTION.
If they are using the wireless adapter for their client machine, they will get stuck trying to login to Atlanta.These same clients will get into the New York ASA with no problems using wired or wireless connections.Windows 7 clients use the Shrewsoft VPN client and Mac clients use the Cisco VPN client. They BOTH BEHAVE the same way and fail to connect to the Atlanta ASA if they use their wireless adapter to initiate the connection.
Using myself as an example.
1. On my home Win 7 laptop using wireless, I can connect to the NY ASA with no issues.
2. The same creditials USED to work for Atlanta as well but have now stopped working. I get stuck until it times out.
3. I run a wire from my laptop to the FiOS router, then try again using the same credentials to Atlanta and I get RIGHT IN.
This makes absolutely no sense to me. Why would the far end of the cloud care if I have a wired or wireless network adapter? I should just be an IP address right? Again, this is beyond my scope of knowledge.We've rebuilt and moved the Radius server to another host in Atlanta in our attempts to troubleshoot to no avail. We've also rebooted the Atlanta Firewall and nothing changed.
We've tried all sorts of remote client combinations. Wireless Internet access points from different carriers (Clear, Verizon, Sprint) all exhibit the same behavior. Once I plug the laptops into a wired connection, BAM, they work connecting to Atlanta. The New York ASA is fine for wired and wireless connections. Same with some other remote office locations that we have.
Below I've detailed the syslog sequence on the Atlanta ASA for both a working wired remote connection and a failed wireless connection. At first we thought the AAA/Radius server was rejecting us but is shows the same reject message for the working connection. Again, both MAC and Windows clients show the same sequence.Where the connection fails is the "IKE Phase 1" process.
-------------------------------------------------------------------------------------------------------------------------
WORKING CONNECTION
-------------------------------------------------------------------------------------------------------------------------
%ASA-6-713172: Automatic NAT Detection Status: Remote end is|is not behind a NAT device This end is|is not behind a NAT device
NAT-Traversal auto-detected NAT.
%ASA-6-113004: AAA user aaa_type Successful: server = server_IP_address, User = user
%ASA-6-113005: AAA user authentication Rejected: reason = string: server = server_IP_address, User = user
[code]...
View 1 Replies
View Related
Mar 19, 2012
how can you configure remote vpn ipsec tunnel on a Cisco 800 router?
View 12 Replies
View Related
Mar 15, 2011
I have a Cisco 2911 router and a Cisco RV 120W router and i would like to establish a VPN tunnel between theese two. I have defined the settings on the Cisco RV 120W router and i just want the Cisco 2911 to follow those. setting up a connection with Cisco IOS.
View 1 Replies
View Related
Aug 9, 2012
I'm having trouble configuring an ASA5505 on version 8.31 code for an IPSec tunnel. I've done this multiple times on 8.2.5 but can't seem to get my tunnel to even attempt to come up on this ASA. Not sure if it's relevent or not, but this remote ASA has never been used for another VPN tunnel before. When I attempt to ping a host on the other side of my tunnel, I just see the following: 8108# sho crypto isa sa
There are no isakmp sas
My local network is 10.1.1.X/24 and my remote peer network contains 66.37.227.X/24. I've been working on this for the better part of the day and would love to get it resolved.
View 8 Replies
View Related
Oct 28, 2012
I am trying to configure RemoteDesktop on a home lab ASA5505 with IOS 8.4.1 and no matter what I tried, I am unable to remote into a local server behind the firewall. I've searched online and found several threads with solutions online including here at Cisco Support Community forum and have tried them all, but have no success. I'm sure it may be something very simple that I've missed.
ASA Version 8.4(1)!interface Vlan1nameif insidesecurity-level 100ip address 192.168.148.5 255.255.255.0!interface Vlan2nameif outsidesecurity-level 0ip address 67.x.x.75 255.255.255.128!interface Ethernet0/0switchport access vlan 2!interface Ethernet0/1!interface Ethernet0/2shutdown!interface Ethernet0/3shutdown!interface Ethernet0/4shutdown!interface Ethernet0/5shutdown!interface Ethernet0/6shutdown!interface Ethernet0/7shutdown!ftp mode passivedns domain-lookup outsidedns server-group DefaultDNSname-server 67.x.x.75domain-name demo.localobject network insidesubnet 192.168.148.0 255.255.255.0object network rdp-serverhost 192.168.148.105object service rdpservice tcp source eq 3389access-list outside_in extended permit tcp any object rdp-server eq 3389pager lines 24mtu inside 1500mtu outside 1500icmp unreachable rate-limit 1 burst-size 1no asdm history enablearp timeout 14400nat (inside,outside) source static rdp-server interface service rdp rdpnat (inside,outside) source dynamic inside interfaceaccess-group outside_in in interface outsideroute outside 0.0.0.0 0.0.0.0 67.x.x.75 1
View 7 Replies
View Related
Mar 18, 2012
i want to create Remote IP Sec VPN on Cisco ASA5510.Problem is this 5510ASA is behind another 5520ASA and it dont have any public IP address on any of 5510 interface.if i do static NAT of ASA 5510 Private IP on internet facing 5520 IP Public POOL, then will VPN work on 5510 ASA? and what ports need to forward on 5520 for 5510 to become IPSEC VPN head end
View 1 Replies
View Related
Jan 25, 2012
I have a old server that has custom apps developed by a bankrupt company that we can't replace yet. We are being tasked with upgrading the Operating System and security patches, while preserving the existing live server. I was able to accomplish this by virtualizing it, then cloning the virtual machine. Where I got stuck was, the custom app requires a specific host name. So, I got the idea to have the two servers live on different sides of the firewall until the test platform is accepted and the old live one can be retired.
My problem is that I have no experience with configuring a real firewall like this asa5510.
Servers are:
CM1 live server
CM2 test platform
ADS Active Directory and File and Print
[code]....
I've started to carefully poke around in the Cisco ASDM-IDM, but haven't figured out how to access the DMZ from the outside (so far just testing with http as I don't have my certificate to setup https just yet). Am I missing something to get through to the DMZ from the WAN side?
View 2 Replies
View Related
Sep 30, 2012
I have a 6 month old RV042 with the newest firmware (v4.2.1.02). Over the weekend I configured the DMZ which after a lot of trial and error, was able to get working. Prior to configuring DMZ, I was able to log in with remote management. However now remote management no longer works. I've tried:
- Rebooting the router
- Turning the firewall off/on
- Turning remote management off/on
- Changing the remote management port
The only step I haven't taken is resetting the router back to factory defaults and trying to reconfigure it all again. This router is so finicky I have no faith I'd be able to get my current functionality back again.
View 2 Replies
View Related
Jan 22, 2013
I have a Cisco ASA 5512 device. I'm using both clientless SSL vpn. And also IPSEC which is used for our external users who connect using an IPAD and then a remote client to remote desktop into our terminal server.I created the connection using the IPSEC wizard in the ASDM software. Usually the connection works fine, but intermittently it fails to allow the user to connect using RDP.I'm able to initiate the VPN connection, and it says connected and can confirm the connection is up, however when trying to connect to the RDP server, it eventually times out. It was working fine most of the time as I say, however now I can't connect at-all.I've viewed the lgo as I try and connect and can see that my evice tries to initiate the connection, but can't quite figure out what it's trying to do. If I look at the connection in the monitoring page it says that its connected. But it's RX traffic has a value, but the TX value is 0.The interesting thing is, I can't connect, but at present have a user that is connected fine and working properly.
View 1 Replies
View Related
Apr 5, 2012
I just made a VPN on my ASA 5505 at home, I can connect successfully to it, but I can't contact anything in the network, nothing respond to ping or to anything else (include the ASA inside IP).
View 3 Replies
View Related
Feb 29, 2012
I configured my cisco client with the info from the vpn wizard and get the following error :
error in the cisco vpn client when enabling the log : Invalid SPI size (log) + reason 412 the remote peer is no longer responding (application) message I see via the ASDM-IDM : Built inbound UDP connection for interface WAN
I'll explain briefly what I'm trying to do here :
* Remote vpn with windows users having cisco clients
* Group authentication and in the asa5510 LOCAL authentication
My WAN interface contains a public ip/29 I also defined a LAN interface with security level 100 in 10.0.60.0 255.255.252.0 range the vpn dhcp range I want to attribute to vpn users : 10.0.69.0/24
Basically I want users to initiate the vpn tunnel to the public IP and be able only to access the LAN range with the 10.0.60.0/22 range
ASA Version 8.2(5)
!
hostname xxxx
domain-name xxxx
[Code].....
View 7 Replies
View Related
Nov 2, 2011
I have a 2911 router where I was configuring the device to allow remote desktops connections. Everything is working properly, but for some reason my ACL has disappeared.
View 5 Replies
View Related
Mar 26, 2012
We have network that uses a Cisco router and use a WAP54G to access the network wirelessly.
We use static IP address so if someone wants to use the wireless an IP address has to be assigned to it and be manually configured for IP Address, Gateway, Sub Net Mask and DNS.
This is becoming unwieldly, but it is safe. Is there any way to config the WAP54G as a router that would automatically assign an IP address in a range just for wireless devices.
Therefore the wireless devices could be set up as DHCP and we would use WPA/WPA2 encryption with a passkey, instead of just assigning static IP addresses.
View 1 Replies
View Related
Oct 12, 2012
I am setting up a simple remote IPsec VPN with a ASA 8.4. All I want to do is the remote user can VPN into the ASA, from there, he can browse the outside Web pages in the internet. and we'd like not to use split-tunneling. The outside infterface is 192.168.1.155/24, which is inside our network and this subnet works fine to outside. The pool for vpn is 192.168.0.0./24 (please pay attention to the 3r octet)
I configured and the remote user can vpn in and get an IP from the pool. but it seems that he cannot do anything. he cannot ping anything.I suspected the NATTing that i use. What is configured wrong? What traffic need to be natted and what need not.
======:ASA Version 8.4(2) !
!interface GigabitEthernet0description VPN interfacenameif outsidesecurity-level 0ip address 192.168.1.156 255.255.255.0 !interface GigabitEthernet1description VPN interfacenameif insidesecurity-level 100ip address 192.168.0.1 255.255.255.0
!ftp mode passiveobject network obj-192.168.0.0subnet 192.168.0.0 255.255.255.0object network obj-192.168.1.155host 192.168.1.155access-list EXTERNAL extended permit ip any any access-list EXTERNAL extended permit icmp any any access-list vpn extended permit ip 192.168.1.0 255.255.255.0 192.168.0.0 255.255.255.0 pager lines 24mtu outside 1500mtu inside 1500ip local pool testpool 192.168.0.10-192.168.0.15ip verify reverse-path interface outsideicmp unreachable rate-limit 1 burst-size 1icmp permit any outsideicmp permit any insideno asdm history enablearp timeout
[code]....
View 17 Replies
View Related
Dec 20, 2011
I have difficulties with configuring Remote IPSec VPN with Cisco ASA 5505 and Windows 7 native VPN client. My client PC gets VPN pool IP address, and can access remote network behind ASA, but then I lose my internet connectivity. I have read that this should be an issue with split tunneling, but I did as it is told here and no luck.On Windows VPN Client settings, if I uncheck "use default gateway on remote network" I have internet connectivity (since client is using local gateway), but then, I cannot ping remote network.In log, I see this warnings of this type:Teardown TCP connection 256 for outside:192.168.150.1/49562 to outside:213.199.181.90/80 duration 0:00:00 bytes 0 Flow is a loopback (cisco)I have attached my configuration file (without split-tunneling configuration I tried). If you need additional logs I'll send them right away.
View 4 Replies
View Related
Mar 18, 2012
We are trying to add an additional LAN-to-LAN IPsec VPN to our network. We currently have one remote office connected, when we configure the second VPN matching the first the tunnel never begins to establish. There is an ACL that is dening the static IP for our remote office.
The layout is as follows:
Main office = ASA 5520
Remote Office A = ASA (Unknown Model)
Remote Office B = Adtran Router
All devices have static IP addresses.
We used the ASDM VPN wizard to create both VPN's.
We have created a rule allowing all traffic from our remote office IP, and that had no effect on the VPN aside from eliminating the following message from our logging:
4 Mar 19 2012 15:18:01 106023 67.50.19.230 50234 TWT-hq-e 31326 Deny udp src TWT-outside:67.50.19.230/50234 dst inside:TWT-hq-e/31326 by access-group "outside-in" [0x0, 0x0]
We have verified that both sides are configured the same however the VPN never is initiated so as of right now the ASA is simply blocking all attempts from our remote office to connect.
View 1 Replies
View Related
