Cisco Firewall :: Tell If PIX515e Image Is Genuine?
Aug 28, 2011
I just bought a used PIX515e. It is running version 8.0(3) and ASDM 6.1.5 Because I do not know the history of the unit, how can I tell if the image used came from cisco and not some download site? I guess I should've thought about this before buying it but hindsight is...you know. Worse case is that the person who had it before me dl the software that was infected with a backdoor or something else. I don't have a service contract so I'm kinda stuck.
Can I download the image from the firewall flash and compare a MD5SUM?
View 12 Replies
ADVERTISEMENT
Feb 9, 2012
I'm have upgraded our ASA5510's from 7.0.8 to 8.4.3 and now I just need to do the ASDM, but get this error? The bin file has been uploaded: [code] Device Manager image set, but not a valid image file disk0:/asdm-647.bin.
View 3 Replies
View Related
Mar 27, 2013
I have a PIX 515E UR which I would like to activate the VPN-3DES-AES license. I did find a link to register the license, but after following the link and logging into my old CCO account i found that as I didn't have access to anything, so couldn't complete the procedure.Is there any way that I can get the license activated? I bought the unit from a Cisco partner quite some time ago, but never needed the 3DES license. Now I do.
View 3 Replies
View Related
Jun 27, 2012
I need configuring a newly reinstated PIX515E with IOS 6.3 to test the configuration of a load balancer.I would like to setup with two Inside interfaces (or simply two interfaces) for testing. I just need it to pass traffic (basically HTTP and HTTPS) between these two interfaces without using NAT.The older IOS is causing me some problems. I don't have an outside interface configured for Internet access,but trying to connect via IP address does't work either. I may be able to configure a second DNS server for the 192.168.12.X network for testing purposes if needed. I even tried to set the default route to the Interface of the production ASA's inside interface (3.1), but that did not work either.
View 6 Replies
View Related
Feb 12, 2012
I just added a PIX515E to my lab (since this is a lab, if I need to change IP address, that is not a problem)....I thought I configured it right, but I am not able to ping any of my other routers/PCs.I have EIGRP on the other three routers, but not sure if I configured it right on the PIX.The diagram below shows my current network topology....(right now the PIX is connected vai Ethernet 1 to the switch, not the router itself) [code]
View 13 Replies
View Related
Feb 16, 2012
We are planning to upgrade the PIX515e (128 MB, 16 MB flash) adaptive software from 7.2(4) to 8.0.3(ED). In our environment the two PIXes are working in active-standby mode and experiencing high memory utilization.
1) What are the bug fixes(like memory leak fix) and new configuration options in the 8.0.3(ED)?
2) Is there any issues to upgrade 7.2 to 8.0.3(ED)?
3) Is the upgrade to new version software fix the memory utilization issue?
View 1 Replies
View Related
Sep 8, 2012
why the ethernet 3,4,5 is not licensed here ?
View 3 Replies
View Related
Mar 17, 2012
i wounder why i'm getting such log message whenever i'm trying to reach my remote site: No translation group found for tcp src outside XXXX dst dmz ZZZZ, i have a Cisco PIX515E firewall and that message is captured there, the traffic is going through a VPN tunnel (the VPN are up on both ends)
View 2 Replies
View Related
Jun 28, 2012
We have two PIX515E ( 6.3), one is Primary( Active) and second one is Standby. after configuration of Secondary Firewall as Standby. getting problem.
1. Configuration part everything is fine
2.we have done failover text also .
Aster Some time , we are not able see Standby Firewall its going down .
View 2 Replies
View Related
Nov 28, 2011
Quick question. I have a site - site tunnel that is up and running between a Pix 515E and a 3050 appliance.Tunnel is up and running but on the pix side I dont see traffic from a couple of subnets behind the inside interface.On the vpnallow access list there are no hits So I setup a capture on the inside interface to see if the packets is making it to the inside interface and nothing. There is some traffic making it thru the tunnel that would have to hit the inside int first and even that doesnt showup in the capture.
View 1 Replies
View Related
Sep 15, 2011
I have a PIX515E. I need to create a vpn to my clients office. PIX is alerady having two VPN, among two one is a dynamic VPN to a dynamic IP of netgear router.
It has two gateway(public IP). Configuration in MH2001 is pretty simple. and i have completed it.I have also completed configuration in PIX using ASDM. But the VPN is not up till now.
[code]...
View 1 Replies
View Related
May 20, 2012
I am trying to veiw my PIX515e via the ASDM, but I am unable to...Can you review my config and make sure I have everything setup the way it is supposed to?
PIX Version 8.0(4)32
!
hostname pixfirewall
domain-name jkkcc.com
enable password DQucN59Njn0OjpJL encrypted
passwd DQucN59Njn0OjpJL encrypted(code)
View 1 Replies
View Related
May 20, 2012
I am trying to veiw my PIX515e via the ASDM, but I am unable to...Can you review my config and make sure I have everything setup the way it is supposed to?
PIX Version 8.0(4)32
!
hostname pixfirewall
[Code].....
View 3 Replies
View Related
Jan 13, 2013
The infrastructure has PIX515E as the Firewall and few Web Servers and Database Servers inside. Is it possible to retreieve information regarding the bandwidth available at the outside interface of PIX (Internet link utilization ) utilized by each of the nodes seperately? I could use SNMP to get the overall data transfer at the Outside interface of PIX but isit possible to get utilization details of individual nodes ? Is Netflow an option ?
View 10 Replies
View Related
Oct 18, 2012
Is there a way to find out if I have purchased a genuine wusb100 adapter? Can I find out by looking at the hardware. I bought from ebay.
View 1 Replies
View Related
Sep 27, 2012
i just installed a pix515e ( ios ver 6.2) in my network. and the vpn users can connect to it from the internet successfully but they aren't able to connect to any of the internal resources. some other informaion: i configured nating between the internal network (10.0.0.0/24) and the internet and another static nat policy between an internal resource through another public ip address on outside interface. but right now i need to let the vpn clients to connect to my internal resources.
View 5 Replies
View Related
Jul 18, 2011
I am in the process of migrating my config from my PIX running 8.0(4) to my ASA5520 running 8.2(1). I have converted the config so that it is ready for the ASA. I noticed the "boot system flash:" and "asdm image flash:" command references the old PIX files. Do I need to update these or will they be updated when the ASA reboots with the new config?
View 2 Replies
View Related
Aug 4, 2011
i have an ASA 5510. it was running asa708-k8.bin and i have attempted to install asa821-k8.bin. i have done this on many ASAs before effortlessly.this time i have had an issue. the ASA will not load the new image, and for some reason will not even load the old.the ASA seems to just keep crashing. i have erased disk0 (advised in forum): and attempted to load the image from tftp. please see below. i know i need to re-formaet the flash, but cannot get into the ASA at all to complete this. [code]
View 2 Replies
View Related
Mar 29, 2011
I got a PIX 501 off ebay and im trying to upgrade it to have an ASDM image on it.Ive downloaded every copy of the ASDM image i can get my hands on, and when i transfer it to the PIX when its up and running i get out of memory, If i do it through monitor mode, i get the error "bad magic number" no matter what i transfer to itI can transfer a new image to the PIX (a non asdm one through monitor mode.
View 3 Replies
View Related
Aug 28, 2011
I have a pix 515, time to time the firewall start rebooting with invalid flash error I found erasedisk.bin in internet, after that i cant load pix532.bin ios file and others pix***.bin are not workingThe only file i am able to load is pix508.bin it,s start asking me activatin number before install I have a previous activation number ios version 5.3.2 but this number is not correct.
View 1 Replies
View Related
Apr 3, 2012
We are now using image 8.0(4) for my ASA 5510. Later on, I would like to upgrade the image to 8.4(3).May I have to know what difference for those images, what should I take care of the script?
View 1 Replies
View Related
May 16, 2011
I upgraded my ASA 5520 with the latest image. Now I get an error upon launching ASDM.Your ASA image has a version number 7.2(4) which is not supported by ASDM 6.4(1), use Device Manager version 5.2(x)Continue Anyway?
What are the newest, recomended image versions of ASA and ASDM I should be using?I will also be using the SSM-20 module with this setup, so I would like to stay with a working version of ASDM.
View 1 Replies
View Related
Jan 11, 2010
I need to upgrade the fwsm image from 3.1(10) to 4.0(8). Can i do it directly from 3.1(10) to 4.0(8) ?Do i need to upgrade other image also along with Firewall version 4.0(8)?
[code]....
View 5 Replies
View Related
Mar 17, 2012
I downloaded a new image to my ASA 5510 and found out up on reboot that the ASA doesn't have enough memory so I am booting to the "ciscoasa" prompt with no config. I still have my old image in disk0:. How do I roll back to this old image?
View 1 Replies
View Related
Nov 30, 2011
I have a pair of asa5520's in active/standby configuration. I plan on ugrading the asa/asdm images to 8.4 shortly (currently on 8.0) and would like to do this with zero downtime. Specifically, I would like to upload the new software to the standby unit, upgrade it, swap standby/active units and then upgrade what will become the standby after the swap.The problem I'm having is getting the new images uploaded onto the standby unit. I've read that the routing table is not shared from the primary and the USB ports are "for future use". I have no problem uploading the new images to the active unit via tftp...but can't do the same to the standby.
View 5 Replies
View Related
Feb 28, 2012
i am using asa821-k8.bin image, in my cisco 5520, How can i check if my IOS is vulnerable ?
View 4 Replies
View Related
Mar 18, 2011
I am wondering how to change which image is loaded by default on an ASA5510. I have two image files stored in the flash memory on disk0:/ but need to change which one is loaded on boot. I used the command "boot system disk0:/asa722-12-k8.bin" which completed successfully, but when the system starts it says two images exist and the default is 1, loading the previous file. Is there a command to change the order that is used?
View 2 Replies
View Related
May 1, 2011
I have an ASA 5505 that I was updating from frimware 8.04 to 8.41. Anyway, I went through the update procedure half-asleep and accidentally deleted the boot image right after I installed it (I used the CLI and put in the command del asa8*.bin then just hit enter a bunch of times, which of course means I deleted the old firmware too).
So now whenever I power up the ASA, I get the "Could not find boot file" error. Is there a guide somewhere that tells me how can upload another boot image to the ASA and set the ASA to boot it from teh ROMMON prompt?
View 1 Replies
View Related
Mar 22, 2011
I have a Cisco 5505 that had its disk erased (erase:disk0) and now I am trying to load a new image (822 or 813) from a tftp server.
From the ROMMON prompt I have configured the relevant parameters and run a tftp command.
The tftp transfer seems to complete successfully but then it gets stuck on "...loading".
I have tried different versions of IOS and I always experience the same problem, even though, with older versions of IOS (7.x), the device manages to reboot itself but then it crashes with the following error:
"Error : Uncompression of the image failed. invalid compressed data--format violated"
Could it be an hardware related-issue or a licensing problem maybe? or am I missing anything obvious?
also, with regards to the license: once restored, how do I get my 50 users license back?
View 5 Replies
View Related
Jan 13, 2013
May I have to know how to check functions included for asa image NCI-ASA5520-BUN-K9?
View 2 Replies
View Related
Feb 16, 2013
we have an ASA5520 need upgrade new anyconnect client, but the new version is too big, so it's no enough space. I want to delete the ASDM image to free the more space. My question is when I delete the ASDM image,if I could manage the ASA from web browser?
View 5 Replies
View Related
Dec 15, 2012
Firmware asa805-k8 was installed and saved on an ASA5505. Upon power failure the ASA5505 reverts to an older firmware, asa724-k8. 1) Is it normal for ASA5505's to revert to older version upon power failure. 2) ASDM/web browser doesn't work using IE--username and password brings to empty screen. how to revert back to later image.
"
# sh ver
Cisco Adaptive Security Appliance Software Version 7.2(4)
Device Manager Version 5.2(4)
[Code]......
View 3 Replies
View Related
Jun 17, 2012
I've been trying to configure this Cisco ASA 5505 for days now. I used to be able to use the ASDM gui application, but i've since transitioned into using the CLI. Trying to go back to ASDM, it won't let me get back in, and when i try show asdm image, it says Device Manager image file not set. I have no CD for this device and I need that image file for the ASDM. How can I locate the file and install it on the router so I can use it?
View 2 Replies
View Related
