Cisco Firewall :: Pix515e Ethernet 3 / 4 And 5 Not Licensed
Sep 8, 2012why the ethernet 3,4,5 is not licensed here ?
View 3 Replies
ADVERTISEMENT
Cisco Firewall :: Getting VPN-3DES-AES Key For PIX515E?
Mar 27, 2013I have a PIX 515E UR which I would like to activate the VPN-3DES-AES license. I did find a link to register the license, but after following the link and logging into my old CCO account i found that as I didn't have access to anything, so couldn't complete the procedure.Is there any way that I can get the license activated? I bought the unit from a Cisco partner quite some time ago, but never needed the 3DES license. Now I do.
View 3 Replies View RelatedCisco Firewall :: Need Test Configuration With PIX515E
Jun 27, 2012I need configuring a newly reinstated PIX515E with IOS 6.3 to test the configuration of a load balancer.I would like to setup with two Inside interfaces (or simply two interfaces) for testing. I just need it to pass traffic (basically HTTP and HTTPS) between these two interfaces without using NAT.The older IOS is causing me some problems. I don't have an outside interface configured for Internet access,but trying to connect via IP address does't work either. I may be able to configure a second DNS server for the 192.168.12.X network for testing purposes if needed. I even tried to set the default route to the Interface of the production ASA's inside interface (3.1), but that did not work either.
View 6 Replies View RelatedCisco Firewall :: PIX515E Change IP Address
Feb 12, 2012I just added a PIX515E to my lab (since this is a lab, if I need to change IP address, that is not a problem)....I thought I configured it right, but I am not able to ping any of my other routers/PCs.I have EIGRP on the other three routers, but not sure if I configured it right on the PIX.The diagram below shows my current network topology....(right now the PIX is connected vai Ethernet 1 to the switch, not the router itself) [code]
View 13 Replies View RelatedCisco Firewall :: Tell If PIX515e Image Is Genuine?
Aug 28, 2011I just bought a used PIX515e. It is running version 8.0(3) and ASDM 6.1.5 Because I do not know the history of the unit, how can I tell if the image used came from cisco and not some download site? I guess I should've thought about this before buying it but hindsight is...you know. Worse case is that the person who had it before me dl the software that was infected with a backdoor or something else. I don't have a service contract so I'm kinda stuck.
Can I download the image from the firewall flash and compare a MD5SUM?
Cisco Firewall :: PIX515e Software Upgrade From 7.2 To 8.0.3 (ED)?
Feb 16, 2012We are planning to upgrade the PIX515e (128 MB, 16 MB flash) adaptive software from 7.2(4) to 8.0.3(ED). In our environment the two PIXes are working in active-standby mode and experiencing high memory utilization.
1) What are the bug fixes(like memory leak fix) and new configuration options in the 8.0.3(ED)?
2) Is there any issues to upgrade 7.2 to 8.0.3(ED)?
3) Is the upgrade to new version software fix the memory utilization issue?
Cisco Firewall :: PIX515E - No Translation Group Found For TCP
Mar 17, 2012i wounder why i'm getting such log message whenever i'm trying to reach my remote site: No translation group found for tcp src outside XXXX dst dmz ZZZZ, i have a Cisco PIX515E firewall and that message is captured there, the traffic is going through a VPN tunnel (the VPN are up on both ends)
View 2 Replies View RelatedCisco Firewall :: Standby PIX515E Not Working After 1 Hour?
Jun 28, 2012We have two PIX515E ( 6.3), one is Primary( Active) and second one is Standby. after configuration of Secondary Firewall as Standby. getting problem.
1. Configuration part everything is fine
2.we have done failover text also .
Aster Some time , we are not able see Standby Firewall its going down .
Cisco Firewall :: Pix515E 6.3.5 Capturing VPN Traffic On Inside INT
Nov 28, 2011Quick question. I have a site - site tunnel that is up and running between a Pix 515E and a 3050 appliance.Tunnel is up and running but on the pix side I dont see traffic from a couple of subnets behind the inside interface.On the vpnallow access list there are no hits So I setup a capture on the inside interface to see if the packets is making it to the inside interface and nothing. There is some traffic making it thru the tunnel that would have to hit the inside int first and even that doesnt showup in the capture.
View 1 Replies View RelatedCisco Firewall :: PIX515E - Create VPN To Clients Office
Sep 15, 2011I have a PIX515E. I need to create a vpn to my clients office. PIX is alerady having two VPN, among two one is a dynamic VPN to a dynamic IP of netgear router.
It has two gateway(public IP). Configuration in MH2001 is pretty simple. and i have completed it.I have also completed configuration in PIX using ASDM. But the VPN is not up till now.
[code]...
Cisco Firewall :: Unable To View PIX515e Via ADSM
May 20, 2012I am trying to veiw my PIX515e via the ASDM, but I am unable to...Can you review my config and make sure I have everything setup the way it is supposed to?
PIX Version 8.0(4)32
!
hostname pixfirewall
domain-name jkkcc.com
enable password DQucN59Njn0OjpJL encrypted
passwd DQucN59Njn0OjpJL encrypted(code)
Cisco Firewall :: Unable To View PIX515e Via ASDM?
May 20, 2012I am trying to veiw my PIX515e via the ASDM, but I am unable to...Can you review my config and make sure I have everything setup the way it is supposed to?
PIX Version 8.0(4)32
!
hostname pixfirewall
[Code].....
Cisco Firewall :: PIX515E - Internal Nodes / Bandwidth Utilization?
Jan 13, 2013The infrastructure has PIX515E as the Firewall and few Web Servers and Database Servers inside. Is it possible to retreieve information regarding the bandwidth available at the outside interface of PIX (Internet link utilization ) utilized by each of the nodes seperately? I could use SNMP to get the overall data transfer at the Outside interface of PIX but isit possible to get utilization details of individual nodes ? Is Netflow an option ?
View 10 Replies View RelatedCisco Firewall :: Connect Internet VPN Clients (on Pix515e) To Internal Resources
Sep 27, 2012i just installed a pix515e ( ios ver 6.2) in my network. and the vpn users can connect to it from the internet successfully but they aren't able to connect to any of the internal resources. some other informaion: i configured nating between the internal network (10.0.0.0/24) and the internet and another static nat policy between an internal resource through another public ip address on outside interface. but right now i need to let the vpn clients to connect to my internal resources.
View 5 Replies View RelatedCisco Firewall :: Migrating PIX515E To ASA5520 - Update BIN Files In Configuration For ASA?
Jul 18, 2011I am in the process of migrating my config from my PIX running 8.0(4) to my ASA5520 running 8.2(1). I have converted the config so that it is ready for the ASA. I noticed the "boot system flash:" and "asdm image flash:" command references the old PIX files. Do I need to update these or will they be updated when the ASA reboots with the new config?
View 2 Replies View RelatedCisco :: Licensed Host Limit Of 10 Exceeded?
Sep 28, 2011I thought that in the past I had problems with my ASA5505 because I had to reboot a number of times, now that I have logging enabled I can see the following: -Deny traffic for protocol 17 src inside, licensed host limit of 10 exceeded.Does this mean that I can not have any more than 10 inside host going out of the outside interface at any time, if not what this means and how I can solve it.
View 16 Replies View RelatedCisco :: ASA 5505 Licensed Limit For SSH Sessions?
Sep 11, 2011I have the default license for a ASA 5505 and this last Friday I received the attached log for SSH sessions through this firewall; we want to be clear about this issue. This limitation has to be with the 10 Inside Host or the Total VPN Peers limitations in this license? This firewall exists only to agree with a PCI requirement between our router and a communication with a Payment Card Industry Brand, all of this in the same site.
ASA5505 <164>Sep 09 2011 10:42:08: %ASA-4-450001: Deny traffic for protocol 6 src DMZ:X.X.X.X/2479 dst DMZ1:X.X.X.X/22, licensed host limit of 10 exceeded.
I hope that the communications through 22 TCP port, are not countable for license propose.
Licensed features for this platform:
Maximum Physical Interfaces : 8
VLANs : 3, DMZ Restricted
Inside Hosts : 10
Failover : Disabled
VPN-DES : Enabled
[code]....
Cisco Application :: ACE 4710 / Verify How Much Licensed Features Are Used
Mar 14, 2012is there a way to verify how much licensed features are used?If the usage is far or near to the limit?
View 4 Replies View RelatedCisco Switching/Routing :: WS-C3750X-48T-S / IP BASE Licensed Connected As Stack
Mar 15, 2013I have two WS-C3750X-48T-S which is "IP BASE" licensed, which are connected as stack.I need to use Policy Based Routing (PBR) to direct Vlans to two different gateways, and command "ip policy route-map" which is supported only in C3750-IPSERVICES license.Do I need upgrade only master switch with Cisco IOS IP Services - product upgrade licenseMfg. Part#: L-C3750X-48-S-E, or both switches need to be upgraded?
View 20 Replies View RelatedSet Up VPN With Cisco PIX515E-R?
Jun 24, 2012I have a Cisco PIX515E-R and I will like to set up a VPN tunnel together with a Netgear ADSL router. I want to access a network at work from my computer at home.
View 14 Replies View RelatedCisco VPN :: Routing In PIX515E Version 6.35
Dec 26, 2011I have a routing problem here with routing in PIX515E version 6.35. I have some Client PCs located in the DMZ interface of the PIX515E, they connect to PIX using Cisco VPN Client (IPSEC VPN), after that these PCs can be routed to access Servers (static route) located behind Internal interfaces of PIX. I have some Servers located remotely having Internet Access, the gateway router remotely connect to PIX Outside Interface (Internet) using IPSEC VPN then routed to inside Interface (static route).
View 9 Replies View RelatedCisco :: Network Assistant In PIX515E
Jun 25, 2006i have managed to create a community of cisco devices however although i can add the pix to the community it does not show up in the topology? HTTPS is enable. I can also access the pix via ASDM.
View 2 Replies View RelatedCisco VPN :: Client To Site Users On PIX515E
Feb 12, 2011 i have PIX515E firewall but i need to know through CLI how can i see the usernames for my VPN clients?
SH vpnclient? or sh ?
Cisco VPN :: PIX515E / IPSec Routing Halts Randomly?
Sep 4, 2011We have got an issue with an IPSec tunnel between Cisco PIX515E and Juniper firewall, the last one is managed by ISP. The tunnel is set up over the Internet.
There are a number of subnets running via this tunnel. The issue is that sometimes the connectivity between some of the subnet halts. So the users (and nagios) would report they can not access the service over the tunnel, while I would access the PIX over the tunnel by telnet just fine (from another side), then issue 'clear ipsec sa', and the connectivity would be restored. This happens randomly, one or few times a day.
Cisco VPN :: PIX515e / 713060 / Tunnel Rejected / User Not Member Of Group
Dec 17, 2011I just configure VPN for end users in PIX515e with IOS 8 and get stuck with "Tunnel Rejected: User (msveden) not member of group (VPN-shared), group-lock check failed.". tell me how I add user to my VPN group?
View 1 Replies View RelatedCisco VPN :: Site-to-Site Not Working Between PIX515e And ASA5505
Aug 9, 2011he IPSec tunnels do not form and I notice the error: 3Aug 09 201105:13:26IP = 39.188.41.188, Error processing payload: Payload ID: 1 Reading up on this it looks like it might be an IKE problem but I'm struggling to find the cause (the new 8.4 commands not useful).
The setup is as follows:-
Head Office
PIX515e v6.3(4)
LAN IP 10.0.160.254/24
Branch Office
ASA5505 v8.4(1)
LAN IP 192.168.47.254/24
Cisco Firewall :: ASA 5505 ACLs On Ethernet Interfaces
Aug 18, 2011It is my understanding that ACLs can only be bound to logical interfaces using the access-group command. However, is it possible to somehow apply ACLs simply based on the ASA's local Ethernet interface? For instance, consider the following:
Device A with IP 192.168.1.1/24 is connected to Ethernet0/0 on the ASA. Device B with IP 192.168.1.2/24 is connected to Ethernet0/1 on the ASA.
Since both devices are in the same subnet and presumably the same VLAN, is it possible to manipulate the traffic to and from physical Ethernet interfaces using ACLs in this manner?
My predicament is fairly simple:
Internet --- ASA --- ROUTER
|
DMZ
In addition to NAT, VPN, and various other tricks, my ASA is also routing traffic from my internal LAN and the Internet to servers in the DMZ configured on the ASA. Due to a combination of Internet and DMZ traffic, my relatively slow ASA is struggling to route and thus becoming a bottleneck. My router is comparatively modest in terms of functionality when compared to the ASA but it is fast. My ideal solution would be to somehow harness the ASA's filtering capabilities for my DMZ but use the router to get traffic to and from my internal LAN into the DMZ without using the ASA to route it.
Additionally, it is worth noting that my DMZ is fairly restrictive so using protected or isolated ports would not quite work for me.
Cisco Firewall :: Enabling Traffic On E0/2 And E0/3 Ethernet Ports - ASA 5510
Aug 10, 2011enabling traffic between interfaces on the ASA 5510. Of course I have an outside interface E0/0 and an inside interface (E0/1) for normal operation. The idea was to enable one of the remaining interfaces on the 5510 to attach an internal network resource to for management in case we lost our switch. I am using E0/0 as the outside interface and the inside interface is E0/1. I am wanting to attached a management device on the same inside network IP address range for simplicity. I have E0/2 configured for the same security level (100) as the other inside interface and I also have enabled same-security-traffic permit inter-interface as well but I still cannot access the device on that port. Is there something else I am missing? I guess the best way to explain this is that I want ports E0/2 and E0/3 to act like a "switch" so to say...... The ASA 5505 lets you do this pretty easy but having trouble on the 5510.
View 4 Replies View RelatedCisco Switching/Routing :: 6500 Ethernet Sub-interfaces Over Metro Ethernet
Feb 20, 2012I curently have 2 Data centers connected with a Metro Ethernet Connection. Each Data Center has 6500 with Sup720s. The Metro Ethernet connection is currently conected by a L3 routed interface. I now need to enable VRFs between the locations and want to determine the best way to adjust the Mero. I was considering adjusting the routed interface to use Ethernet sub-interfaces. Each VRF would be given a different subinterface over the Metro Ethernet connection. I have done this on internal LAN connections but am concerned about exteding across data centers over Metro E.
View 1 Replies View RelatedRealtek RTL8168D/8111D PCI-E Gigabit Ethernet NIC Won't Detect Ethernet Cable?
Aug 8, 2012I am having a problem with my Realtek RTL8168D/8111D PCI-E Gigabit Ethernet NIC. It is not detecting my ethernet cable, and thus leaving me without internet on my desktop, after i updated its driver. The cable is not the problem as I have tested the cable with my laptop. I tried rolling back drivers, doing system restore and removing drivers with driversweeper and letting windows install the drivers again. However, none of these worked for me. I doubt the NIC is faulty as it was working before i updated the drivers. I am using windows 7 home premium 64-bit.
View 9 Replies View RelatedEthernet Port Doesn't Recognize Any Ethernet Cord
Dec 26, 2011I've had trouble connecting to my own internet and have no wireless. I'm using my neighbor's wireless and it's really slowing her's down. I've tried restarting my laptop (it usually works) and then reinstalled the device under "device manager". It's not the cord, I've checked with my neighbor's laptop and it works fine.I use a Sony Vaio VGN-NS140E with Windows Vista SP2.
------------------------------------------------------------------------
{ipconfig /all} This is while I only have an ethernet plugged in and no wifi connection.
Windows IP Configuration
Host Name . . . . . . . . . . . . : FairyHo
[code]....
Cisco Firewall :: ASA 5505 / Use The Ethernet Ports As Pure Physical Layer 3 Ports
Jun 9, 2013We have an ASA 5505. 5505 comes with two default vlans 1&2 with each of them marked as inside & outside respectively.My query is , if i do not want to use vlans on 5505 and only want to use the Ethernet ports as pure physical layer 3 ports, is it possible?i.e. i want to assign a layer 3 ip address on eth0/0 and eth0/1 and make them as the inside & outside interfaces rather than vlans. is it possible to do away with vlans in 5505 & will it work otherwise?
View 3 Replies View RelatedWireless Versus Ethernet / Does Ethernet Have Less Ping
Jun 11, 2012I just got a new Xbox today, and use the integrated WiFi card. I was lagging like Crysis 2 on a 6800 GT (forget it). I just got a CAT .5 cable, and plugged it into modem/xbox and IDK... it works, I'm online, but basically my question is:Does ethernet connections have less ping (better) than wireless connections? This is with the Xbox 360 Slim. I know it improves upload, and download, but what about ping?
View 2 Replies View Related