We have two PIX515E ( 6.3), one is Primary( Active) and second one is Standby. after configuration of Secondary Firewall as Standby. getting problem.
1. Configuration part everything is fine
2.we have done failover text also .
Aster Some time , we are not able see Standby Firewall its going down .
I have successfully completed HSRP and failover configuration.When both switch are runnign then the failover run successful and wheneber one link fail then the failover run successfully but when down one 6509(total box) the failover not working.....
View 7 Replies View Relatedlast night I started upgrading our ASA5520 active/standby cluster. Because of lack of memory, I stopped the upgrade process and will continue when the memory modules have arrived... Currently I'm running 8.0(5) on both nodes (Version: Ours 8.0(5), Mate 8.0(5))Whenever I use the "write standby" command on the active ASA, the passive ASA seems to drop it links for a short while. [code]
View 4 Replies View RelatedI have a PIX 515E UR which I would like to activate the VPN-3DES-AES license. I did find a link to register the license, but after following the link and logging into my old CCO account i found that as I didn't have access to anything, so couldn't complete the procedure.Is there any way that I can get the license activated? I bought the unit from a Cisco partner quite some time ago, but never needed the 3DES license. Now I do.
View 3 Replies View RelatedI need configuring a newly reinstated PIX515E with IOS 6.3 to test the configuration of a load balancer.I would like to setup with two Inside interfaces (or simply two interfaces) for testing. I just need it to pass traffic (basically HTTP and HTTPS) between these two interfaces without using NAT.The older IOS is causing me some problems. I don't have an outside interface configured for Internet access,but trying to connect via IP address does't work either. I may be able to configure a second DNS server for the 192.168.12.X network for testing purposes if needed. I even tried to set the default route to the Interface of the production ASA's inside interface (3.1), but that did not work either.
View 6 Replies View RelatedI just added a PIX515E to my lab (since this is a lab, if I need to change IP address, that is not a problem)....I thought I configured it right, but I am not able to ping any of my other routers/PCs.I have EIGRP on the other three routers, but not sure if I configured it right on the PIX.The diagram below shows my current network topology....(right now the PIX is connected vai Ethernet 1 to the switch, not the router itself) [code]
View 13 Replies View RelatedI just bought a used PIX515e. It is running version 8.0(3) and ASDM 6.1.5 Because I do not know the history of the unit, how can I tell if the image used came from cisco and not some download site? I guess I should've thought about this before buying it but hindsight is...you know. Worse case is that the person who had it before me dl the software that was infected with a backdoor or something else. I don't have a service contract so I'm kinda stuck.
Can I download the image from the firewall flash and compare a MD5SUM?
We are planning to upgrade the PIX515e (128 MB, 16 MB flash) adaptive software from 7.2(4) to 8.0.3(ED). In our environment the two PIXes are working in active-standby mode and experiencing high memory utilization.
1) What are the bug fixes(like memory leak fix) and new configuration options in the 8.0.3(ED)?
2) Is there any issues to upgrade 7.2 to 8.0.3(ED)?
3) Is the upgrade to new version software fix the memory utilization issue?
why the ethernet 3,4,5 is not licensed here ?
View 3 Replies View Relatedi wounder why i'm getting such log message whenever i'm trying to reach my remote site: No translation group found for tcp src outside XXXX dst dmz ZZZZ, i have a Cisco PIX515E firewall and that message is captured there, the traffic is going through a VPN tunnel (the VPN are up on both ends)
View 2 Replies View RelatedQuick question. I have a site - site tunnel that is up and running between a Pix 515E and a 3050 appliance.Tunnel is up and running but on the pix side I dont see traffic from a couple of subnets behind the inside interface.On the vpnallow access list there are no hits So I setup a capture on the inside interface to see if the packets is making it to the inside interface and nothing. There is some traffic making it thru the tunnel that would have to hit the inside int first and even that doesnt showup in the capture.
View 1 Replies View RelatedI have a PIX515E. I need to create a vpn to my clients office. PIX is alerady having two VPN, among two one is a dynamic VPN to a dynamic IP of netgear router.
It has two gateway(public IP). Configuration in MH2001 is pretty simple. and i have completed it.I have also completed configuration in PIX using ASDM. But the VPN is not up till now.
[code]...
I am trying to veiw my PIX515e via the ASDM, but I am unable to...Can you review my config and make sure I have everything setup the way it is supposed to?
PIX Version 8.0(4)32
!
hostname pixfirewall
domain-name jkkcc.com
enable password DQucN59Njn0OjpJL encrypted
passwd DQucN59Njn0OjpJL encrypted(code)
I am trying to veiw my PIX515e via the ASDM, but I am unable to...Can you review my config and make sure I have everything setup the way it is supposed to?
PIX Version 8.0(4)32
!
hostname pixfirewall
[Code].....
The infrastructure has PIX515E as the Firewall and few Web Servers and Database Servers inside. Is it possible to retreieve information regarding the bandwidth available at the outside interface of PIX (Internet link utilization ) utilized by each of the nodes seperately? I could use SNMP to get the overall data transfer at the Outside interface of PIX but isit possible to get utilization details of individual nodes ? Is Netflow an option ?
View 10 Replies View Relatedi just installed a pix515e ( ios ver 6.2) in my network. and the vpn users can connect to it from the internet successfully but they aren't able to connect to any of the internal resources. some other informaion: i configured nating between the internal network (10.0.0.0/24) and the internet and another static nat policy between an internal resource through another public ip address on outside interface. but right now i need to let the vpn clients to connect to my internal resources.
View 5 Replies View RelatedI am in the process of migrating my config from my PIX running 8.0(4) to my ASA5520 running 8.2(1). I have converted the config so that it is ready for the ASA. I noticed the "boot system flash:" and "asdm image flash:" command references the old PIX files. Do I need to update these or will they be updated when the ASA reboots with the new config?
View 2 Replies View Relatedhe IPSec tunnels do not form and I notice the error: 3Aug 09 201105:13:26IP = 39.188.41.188, Error processing payload: Payload ID: 1 Reading up on this it looks like it might be an IKE problem but I'm struggling to find the cause (the new 8.4 commands not useful).
The setup is as follows:-
Head Office
PIX515e v6.3(4)
LAN IP 10.0.160.254/24
Branch Office
ASA5505 v8.4(1)
LAN IP 192.168.47.254/24
I have a problem with an internet connection with a customer.They have a Zyxel 660 in bridge mode and the public ip is delivered to the eth0/0 outside interface of a 5505 ASA.They lose internet connectivity a couple of times per hour. What solves the problem immediately is disconnecting the ethernet cable from the eth0/0 and then directly plugging it back. Then it runs for 20-30 minutes or so.The isp doesnt't notice any errors on the dsl connection, only that they cannot ping the outside interface from time to time (duhhh)However, yesterday, when problem appeared for first time , I noticed that this Zyxel was very hot since it was placed on top of the ASA. Now it is set apart.In the meantime I already replaced all cables, but I think it's the Zyxel so I urged that the ISP send a new Zyxel.Though it sounds strange. [code]
View 4 Replies View RelatedI have two WLC version 7.3.101.0 with the standby unit having HA-SKU. I have tested the AP-SSO functionality without any problem in lab with direct connection on RP port between two WLC. Once I brought them into data centre in separate location (latency is less than 10ms between the two DC), the standby unity always went into maintenance mode. The booting process on standby unit went to maintenance mode as shown below:
Management Gateway and Peer Redundancy Management interface are not reachable.Entering maintenance mode.
I have checked on the core switches at 2 data centre that the two WLC RP ports are connected to same VLAN and it is spanned across MAN link (10GB and less than 10ms delay). The spanning tree on those ports are forwarding as well.I have rebooted the second unit but no luck.The interface between two DC is using MTU 9216 which I do not think would cause this issue.
How I can actively monitor the interfaces and overall status of 2 x ASA 5500s in an Active/Standby configuration?
I can setup monitoring of the interfaces on the Active member but I'm not sure how to manage the Standby member?
ASA 8.2(5), uauth absolute timeout is disabled and inactivity timeout is set to 48 hours:
timeout xlate 48:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:00:00 absolute uauth 48:00:00 inactivity
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
Users still get kicked out every 8 hours and they have to reauth. This is a logging message:
%ASA-5-109012: Authen Session End: user 'john', sid 839, elapsed 28801 seconds
Is there a way to access the asa in a failover pair that is in standby mode from the primary asa? IE I am logged into the primary asa via command line and was hoping to access the other asa from here.
View 1 Replies View RelatedI would like to work with two ASA's 5550 in HA (Acitve-Standby) like perimetral firewalls and also work with another ASA 5540 but like a SSL VPN Remote Access to end users.Which will be the best topology to this scenary?. Perhaps i need to put the ASA 5540 SSL VPN together with the ASA's in HA directly in a port.
View 1 Replies View RelatedI'm having an issue where when I upgrade from 8.2(5) to 8.4(2) on an active/passive asa 5585 running in transparent mode I can no longer reach the standby ip. The BVI interface appears to be created properly, the device IP and standby IP are listed in the config under the BVI interface and my inside and outside interfaces are both joined to BVI1-group.
View 1 Replies View RelatedI have this 2x ASA5540 firewall and notice the it is configured with a standby ip. The firewall is run in Active/Passive mode.However, the standby ip of this firewall is not point to the secondary firewall and vice versa for the primary firewall. [code]
1) May i know how is this configuration valid in the first place? I have checked through the configuration. None of the configuration is related to this ip address.
2) Can we remove this standby ip address on both the firewall and correct to the correct primary and seconadary ip address in both firewall?
3) We tried to use this ip address but cannot be used ? Is it related to the configuration of the standby ip address.Do note that the ping to this ip address x.x.x.120 is unreachable.
I have 2 x 5510's in active/standby mode, things look fine until the active one needs to be failed over and I realize the standby one is dead. I never notice as the lights on the ASA look good, I only nice as I can't telnet or console onto it, how can I debug this issue?
View 1 Replies View RelatedI can no longer communicate with the standby IP address configured on the inside interface of a secondary ASA5510. Just a couple days ago I could snmp, http, ssh, and ping it.From the switch that is directly connected to the inside interface I'm getting unexpected results when viewing the the arp table. The switch is saying the IP address associated with the ASA's inside interface has mac address 0023.3353.bcc8 but the ASA is saying its inside interface mac address is 0023.33bb.8362?Furthermore when I issue the "sh mac address-table interface f5/46" command on the switch i see multiple macs on the interface that is connected to the inside interface of the ASA...
Unicast Entries
vlan mac address type protocols port
-------+---------------+--------+---------------------+--------------------
135 0023.3353.bcc8 dynamic ip FastEthernet5/46
135 0023.3353.bdc8 dynamic ip FastEthernet5/46
135 0023.3353.bec8 dynamic ip FastEthernet5/46
135 0023.3353.bfc8 dynamic ip FastEthernet5/46
Come across pix 525 with 7.2.4 , 256 MB RAM, experienceing high memory utilization ?.show memory was giving used memory = 97%.All I had done was, i did a reboot of the firewall since we were not able to take the control of the f/w.I wonder why only the standby f/w had this issue and not the primary does not have, just to rule out that it was not due to Traffic.I have searched in bugtool kits and support forums and did not find anything relevant except for a similar issue for ASA CSCsg43844.
View 3 Replies View Relatedi have 2 ASA 5505 running 8.3(1) and ASDM 6.3(1).
the first unit is currently working, and i now wish to configure the second unit as standby. im configuring through the ASDM GUI. Started the HA Wizard, choose Active/Standby configuration and enter the IP of the peer device. checks come back all ok. On the LAN link configuration page (step 3of6) Interface is pre selected as VLAN99, I give it a logical name as iface_fail, and enter 10.0.0.1 as primary address and 10.0.0.2 as standby, subnet as 255.255.255.248, and select port Ethernet0/5
Note that if i click on the buttons next to the IP fields, i get IP addresses of remote hosts!.
I have a pair of asa5520's in active/standby configuration. I plan on ugrading the asa/asdm images to 8.4 shortly (currently on 8.0) and would like to do this with zero downtime. Specifically, I would like to upload the new software to the standby unit, upgrade it, swap standby/active units and then upgrade what will become the standby after the swap.The problem I'm having is getting the new images uploaded onto the standby unit. I've read that the routing table is not shared from the primary and the USB ports are "for future use". I have no problem uploading the new images to the active unit via tftp...but can't do the same to the standby.
View 5 Replies View RelatedIs there a document that explains how the configurations are updated to the standby ASA and what needs to be manually added tot he ASA? I have two ASA 5510 running ASA ver 8.3(2) and ASDM 6.4(1). When I add static routes to the primary ASA the routes are not sent to the failover ASA. Is this to be expected or do I have a bug?
View 10 Replies View RelatedI have a problem with failover. On My site I have 2 Firewalls 5580. And I did this configuration on my firewall.interface GigabitEthernet3/0description LAN/STATE Failover Interfacespeed nonegotiate.
View 5 Replies View Related