Cisco Firewall :: Need Test Configuration With PIX515E
Jun 27, 2012
I need configuring a newly reinstated PIX515E with IOS 6.3 to test the configuration of a load balancer.I would like to setup with two Inside interfaces (or simply two interfaces) for testing. I just need it to pass traffic (basically HTTP and HTTPS) between these two interfaces without using NAT.The older IOS is causing me some problems. I don't have an outside interface configured for Internet access,but trying to connect via IP address does't work either. I may be able to configure a second DNS server for the 192.168.12.X network for testing purposes if needed. I even tried to set the default route to the Interface of the production ASA's inside interface (3.1), but that did not work either.
View 6 Replies
ADVERTISEMENT
Jul 18, 2011
I am in the process of migrating my config from my PIX running 8.0(4) to my ASA5520 running 8.2(1). I have converted the config so that it is ready for the ASA. I noticed the "boot system flash:" and "asdm image flash:" command references the old PIX files. Do I need to update these or will they be updated when the ASA reboots with the new config?
View 2 Replies
View Related
Mar 27, 2013
I have a PIX 515E UR which I would like to activate the VPN-3DES-AES license. I did find a link to register the license, but after following the link and logging into my old CCO account i found that as I didn't have access to anything, so couldn't complete the procedure.Is there any way that I can get the license activated? I bought the unit from a Cisco partner quite some time ago, but never needed the 3DES license. Now I do.
View 3 Replies
View Related
Feb 12, 2012
I just added a PIX515E to my lab (since this is a lab, if I need to change IP address, that is not a problem)....I thought I configured it right, but I am not able to ping any of my other routers/PCs.I have EIGRP on the other three routers, but not sure if I configured it right on the PIX.The diagram below shows my current network topology....(right now the PIX is connected vai Ethernet 1 to the switch, not the router itself) [code]
View 13 Replies
View Related
Aug 28, 2011
I just bought a used PIX515e. It is running version 8.0(3) and ASDM 6.1.5 Because I do not know the history of the unit, how can I tell if the image used came from cisco and not some download site? I guess I should've thought about this before buying it but hindsight is...you know. Worse case is that the person who had it before me dl the software that was infected with a backdoor or something else. I don't have a service contract so I'm kinda stuck.
Can I download the image from the firewall flash and compare a MD5SUM?
View 12 Replies
View Related
Feb 16, 2012
We are planning to upgrade the PIX515e (128 MB, 16 MB flash) adaptive software from 7.2(4) to 8.0.3(ED). In our environment the two PIXes are working in active-standby mode and experiencing high memory utilization.
1) What are the bug fixes(like memory leak fix) and new configuration options in the 8.0.3(ED)?
2) Is there any issues to upgrade 7.2 to 8.0.3(ED)?
3) Is the upgrade to new version software fix the memory utilization issue?
View 1 Replies
View Related
Sep 8, 2012
why the ethernet 3,4,5 is not licensed here ?
View 3 Replies
View Related
Mar 17, 2012
i wounder why i'm getting such log message whenever i'm trying to reach my remote site: No translation group found for tcp src outside XXXX dst dmz ZZZZ, i have a Cisco PIX515E firewall and that message is captured there, the traffic is going through a VPN tunnel (the VPN are up on both ends)
View 2 Replies
View Related
Jun 28, 2012
We have two PIX515E ( 6.3), one is Primary( Active) and second one is Standby. after configuration of Secondary Firewall as Standby. getting problem.
1. Configuration part everything is fine
2.we have done failover text also .
Aster Some time , we are not able see Standby Firewall its going down .
View 2 Replies
View Related
Nov 28, 2011
Quick question. I have a site - site tunnel that is up and running between a Pix 515E and a 3050 appliance.Tunnel is up and running but on the pix side I dont see traffic from a couple of subnets behind the inside interface.On the vpnallow access list there are no hits So I setup a capture on the inside interface to see if the packets is making it to the inside interface and nothing. There is some traffic making it thru the tunnel that would have to hit the inside int first and even that doesnt showup in the capture.
View 1 Replies
View Related
Sep 15, 2011
I have a PIX515E. I need to create a vpn to my clients office. PIX is alerady having two VPN, among two one is a dynamic VPN to a dynamic IP of netgear router.
It has two gateway(public IP). Configuration in MH2001 is pretty simple. and i have completed it.I have also completed configuration in PIX using ASDM. But the VPN is not up till now.
[code]...
View 1 Replies
View Related
May 20, 2012
I am trying to veiw my PIX515e via the ASDM, but I am unable to...Can you review my config and make sure I have everything setup the way it is supposed to?
PIX Version 8.0(4)32
!
hostname pixfirewall
domain-name jkkcc.com
enable password DQucN59Njn0OjpJL encrypted
passwd DQucN59Njn0OjpJL encrypted(code)
View 1 Replies
View Related
May 20, 2012
I am trying to veiw my PIX515e via the ASDM, but I am unable to...Can you review my config and make sure I have everything setup the way it is supposed to?
PIX Version 8.0(4)32
!
hostname pixfirewall
[Code].....
View 3 Replies
View Related
Jan 13, 2013
The infrastructure has PIX515E as the Firewall and few Web Servers and Database Servers inside. Is it possible to retreieve information regarding the bandwidth available at the outside interface of PIX (Internet link utilization ) utilized by each of the nodes seperately? I could use SNMP to get the overall data transfer at the Outside interface of PIX but isit possible to get utilization details of individual nodes ? Is Netflow an option ?
View 10 Replies
View Related
Sep 27, 2012
i just installed a pix515e ( ios ver 6.2) in my network. and the vpn users can connect to it from the internet successfully but they aren't able to connect to any of the internal resources. some other informaion: i configured nating between the internal network (10.0.0.0/24) and the internet and another static nat policy between an internal resource through another public ip address on outside interface. but right now i need to let the vpn clients to connect to my internal resources.
View 5 Replies
View Related
Aug 2, 2011
security configuration of the 1410 bridge and on how to test the bandwidth/throughput between two 1410 Bridges setup for point-to-point connectivity.
We have setup this in one of our Client sites.
View 3 Replies
View Related
May 3, 2011
Question re: DIR-655; Hardware ver A4; Firmware version 1.32NA
During bandwidth tests to several sites (principally speedtest.net) I get ping times of 10-11 ms, download speeds of 12+ to 17+ mbps but failure on upload tests using my DIR-655.
When I bypass the 655 and test directly with my cable modem, all (including upload) tests work reliably and consistently.
I have swapped the two ethernet cables involved as well as replacing both with new cables but the results are the same (uploads fail with 655 and work without it)
I have seen several postings over the the last year with this same problem but have never seen any comment from D-Link, or a solution from any reader.
Not that it should have any bearing, but I have TA785GE-128M motherboard and am running Windows 7 (patch current) on COMCAST
is this problem acknowledged by D-Link and is there a solution?
View 14 Replies
View Related
Nov 23, 2011
I travel a lot and use wifi in a lot of different places (hotels, airports, etc.)My apps don't always work and I suspect that in some instances the broadband provider is blocking some of the ports I need.I don't need a port scanner like NMAP since that scans a target IP for listening ports.What I need is a way to figure out whether some firewall between my PC and the Internet is blocking specific UDP or TCP port ranges.
View 2 Replies
View Related
Oct 5, 2011
I've cloned the configuration off one of my ASA5510's to another 5510 to use as a template for a new data center deploy. I have configured the new firewalls networks and rules, and of course changed the WAN IP config to its new setting.
I want to test the firewall in y office before I deploy it. How should I configure my Macbooks ethernet configuraiton to test the firewall?, as I have tried without success to connect to it.
Let's say that my WAN configuration is 134.5.169.98/255.255.255.224 with a static route of IP address 0.0.0.0, Netmask 0.0.0.0 and a gateway IP of 134.5.169.97.
I've tried setting the route to force all traffic through the interface (sudo route add 0.0.0.0/1 134.5.169.98), but that did not work either. A trace route to the external interface IP of the firewall (or the external IP of an expose server) get's a "no route to host" error.
I've tried many configurations and have not been able to access the internal servers/services/VPN at all.I've also tried with a cross over, and straight through cables.
What should I configure my macbooks network configuration as so I can connect directly to the WAN port to test external access to the internal servers/services and test the VPN client?
View 8 Replies
View Related
Jun 24, 2012
I have a Cisco PIX515E-R and I will like to set up a VPN tunnel together with a Netgear ADSL router. I want to access a network at work from my computer at home.
View 14 Replies
View Related
Dec 26, 2011
I have a routing problem here with routing in PIX515E version 6.35. I have some Client PCs located in the DMZ interface of the PIX515E, they connect to PIX using Cisco VPN Client (IPSEC VPN), after that these PCs can be routed to access Servers (static route) located behind Internal interfaces of PIX. I have some Servers located remotely having Internet Access, the gateway router remotely connect to PIX Outside Interface (Internet) using IPSEC VPN then routed to inside Interface (static route).
View 9 Replies
View Related
Jun 25, 2006
i have managed to create a community of cisco devices however although i can add the pix to the community it does not show up in the topology? HTTPS is enable. I can also access the pix via ASDM.
View 2 Replies
View Related
Feb 12, 2011
i have PIX515E firewall but i need to know through CLI how can i see the usernames for my VPN clients?
SH vpnclient? or sh ?
View 3 Replies
View Related
Sep 4, 2011
We have got an issue with an IPSec tunnel between Cisco PIX515E and Juniper firewall, the last one is managed by ISP. The tunnel is set up over the Internet.
There are a number of subnets running via this tunnel. The issue is that sometimes the connectivity between some of the subnet halts. So the users (and nagios) would report they can not access the service over the tunnel, while I would access the PIX over the tunnel by telnet just fine (from another side), then issue 'clear ipsec sa', and the connectivity would be restored. This happens randomly, one or few times a day.
View 6 Replies
View Related
Dec 17, 2011
I just configure VPN for end users in PIX515e with IOS 8 and get stuck with "Tunnel Rejected: User (msveden) not member of group (VPN-shared), group-lock check failed.". tell me how I add user to my VPN group?
View 1 Replies
View Related
May 16, 2011
I have two 1811's connected in a lab using a ipsec vpn tunnel (using a switch to simulate an internet connection between them).I am trying to configure one of the routers as a ZBPF just to allow a remote windows login (DC on the firewalled side, workstations on the other side).I'm trying to verify that the zbpf is working, but it doesn't seem to stop anything. I had match icmp added to the class-map, but took it out to test if icmp would fail. It didn't. Basically, I don't think the firewall is working at all. Any thoughts on how I can configure this so that the policies will work between zone-pairs?
Here's an quick drawing:
Here are the configurations:
Local router:
hostname sdc-1811-LocalLab
!
boot-start-marker
boot-end-marker
!
no aaa new-model
!
resource policy
[code]....
View 11 Replies
View Related
May 17, 2011
i have asa 5505 with the asdm v5.2 (4), and the asa v7.2(4). This platform has a base license. if i upgrade adsm and asa on v6.2(1) and v8.2(2) if I lose my license and that you need to activate them? i configured site to site vpn (this firewall and the another) that i lose my configuration if i upgrade my firewall.
View 2 Replies
View Related
Apr 7, 2013
We have an ASA with 8.4(5) version. we had detected that few ip's were getting shunned ,to overcome the problem no shun was used and the traffic normalised.But, the same problem re-occured a few days after that with logs showing traffic being shunned.
is there any fixed way to get rid of this. what commands can i use to verify related configuration on the firewall.
View 3 Replies
View Related
Mar 31, 2013
I have one firewall need to be configured in transparent mode. I have inside and outside router. What is the configuration of transparent firewall ASA8.2. I didn't find the configuration on Cisco site.
View 17 Replies
View Related
Nov 25, 2012
I am trying to set the PIX firewall to transparent mode.After I set it to transparent firewall, I allowed all icmp, tcp, udp traffics.Currently, any devices in the inside network can get the ip automatically from DHCP server in the outside network but cannot ping to any servers in the outside network either access the internet.Do I need additional confiration on the firewall?
Here's the configuration:
PIX Version 7.0(1)
firewall transparent
names
!
interface Ethernet0
[Code]....
View 1 Replies
View Related
Sep 11, 2007
I want to configure an ASA 5505 in transparent mode (7.x). Somehow, I got it to work.. but i need some kind of step by step description. I just want to connect it with outside on a route .. inside in my LAN. Its working now with one ASA. But in the Web Interface the Interfaces inside and outside are down.. but its working.
View 5 Replies
View Related
Aug 9, 2011
he IPSec tunnels do not form and I notice the error: 3Aug 09 201105:13:26IP = 39.188.41.188, Error processing payload: Payload ID: 1 Reading up on this it looks like it might be an IKE problem but I'm struggling to find the cause (the new 8.4 commands not useful).
The setup is as follows:-
Head Office
PIX515e v6.3(4)
LAN IP 10.0.160.254/24
Branch Office
ASA5505 v8.4(1)
LAN IP 192.168.47.254/24
View 3 Replies
View Related
May 5, 2012
Setup new Cisco 861 and working well for a new BTNet line for the customer. Changed the firewall using CCP from Zone to Classic Firewall. Worked great all day and configured what I needed to do.Now, with CCP (version 2.6) have the following message.Cisco CP has detected that the router is configured with either legacy and Zone Policy Firewall (ZPF) or Legacy firewall. If you want to use Cisco CP to configure an zone-based firewall, you must first delete the Legacy configuration.
View 4 Replies
View Related
