Region : Belgium
Model : TL-MR3220
Hardware Version : V1
Firmware Version : 3.12.21 Build 120523 Rel.37880n
ISP : 3G mobile
My router TL-MR3420 does not connect to my 3G modem. I did all the steps according to the router configuration. Despite of that, once it is on the status it doesn�t recognize my modem, HUAWEI, model number E1820.
Region : Others
Model : TL-MR3040
Firmware Version: 3.14.4 Build 121017 Rel.62268n
I have purchased TL-MR3040 especial for share my 3G account . I have connect it by ethernet port and made setups and it is in 3g/4g only mode. In system checks my modem indicated as " Identified" the modem is a Huawei E160E . My notebook and tablet connects by wireless connection to TL-MR3040 but the router does not dial ISP number *99# . The led on usb modem continues flashing. the 3G modem works perfectly with my notebook and tablet and I use the same parameters for TL-MR3040 with tablet. But most of the parameters don't exist on setup pages of TL-MR3040 . [code]
Region : Argentina
Model : TL-MR3220
Hardware Version : V2
Firmware Version :
ISP :
Region : Others
Model : TL-MR3220
Hardware Version : V1
Firmware Version : latest
ISP : Orange
The TL-MR3220 takes a long time to identify the 3g modem and sometimes it will not identify it at all and says "unplugged". Sometimes "unplugged" suddenly apears after the modem has been identified and was working properly.Is this the normal behavior of this device ? Why ? What can be done ? I'm Using Alcatel X500D 3g modem.
When installing the DIR-615, router installs, but error msg that there is no internet connection. SmartConnect is plugged into the WAN and I have tried the ethernet cable to the computer in spots 1 & 2. Good connection when SmartConnect modem is connected to computer directly.615's Internet indicator will turn green for a while, usually less than a minute or two, then flashes, then may actually cause the routers status indicator to flash off, then back on. Like a reset.
View 2 Replies View RelatedRegion : UnitedStates
Model : TD-W8960N
Hardware Version : V3
ISP : Centurylink
I am replacing my qwest/centurylink actiontec q1000 with the td-w8960n. I have run all the different setups, with the different settings that I have found on the net but to no avail. The one thing I have noticed is that the light for the asdl on the td-w8960n does not come on, but yet when I plug it back into the actiontec it sees it and the internet works. Any reason why the td-w8960n is not recognizing the active dsl line?
I have a Speedstream 4300 modem in bridge mode and a linksys WRT54G2 router set to PPPoE like I was instructed. On the status page of my router underneath the PPPoE setting it has IP, Subnet Mask, and Gateway all set to 0. The only advice I was able to obrain from my ISP was to powercycle the router and modem, which I did and no change.
View 1 Replies View RelatedWhen setting up Belkin fF5D8235-4 v2 router it will not recognize the Speedstream 4100 modem. Is there a fix for this?
View 1 Replies View RelatedOk this is the send router this has happened to but anyway after a power blink the router no longer recognizes that i have a modem connected to it no matter how many times I reboot both of them it can't recognize that i have a modem connected i know it is not the modem because i'm using it to type this right now directly connected to my desktop
I have windows 7
Linkysy E4200 V1
Century link DSL modem 660 series
d-lINK n-300 (DIR-615) Wireless Router HW/Ver: E1, F/W Ver: 5.00NA
I am having a problem with the DIR-615 router seeing my printer on a wired network. The printer is a Brother HL-2170W (also capable of a wireless connection). All other network PC's connect okay. I have attempted both wired and wireless connection procedures that came with the printer with no luck. The DIR-615 router does not see the printers IP address. How can I get the router to recognize the printer?
Region : India
Model : TL-MR3020
Hardware Version : V1
Firmware Version :
ISP : aircel,idea
I bought this router just today, but it cant recognize my huawei e303c 3g modem.i've upgraded the firmware. This router supports the dongle or not?
I usually connect my PS3 to a switch which then goes to the BuT Home Hub and it works fine. However, I want to connect the PS3 directly to my Hub but when I plug it in to the Hub, it doesn't connect to the internet at all. Is there something I have to configure in order to get it to work?It is a PS3 160 GB Slim with Firmware 4.0.
View 2 Replies View RelatedI recently upgraded, through my ISP, my high-speed modem to the DPC3825 model modem/router. But when I try to connect to the DLink switch, the modem freezes, and doesn't recognize it. My previous setup was modem, to my DLink router (DIR 615), to my switch. With my new setup, I just bypassed the DLink router, because my new modem includes router capability.Is there some compatibility issue between the new modem and the DLink switch?
View 1 Replies View Relatedi just bought a Netgear WNDR4000 router due to troubles with my current modem/router combo (D-Link DSL2730-B). The router doesnt have in built modem functionality obviously so I need to set up the modem/router as a dedicated modem.Also should I use the current modem/router as the dedicated modem or an older model i own (I think its a DSL 502T)? Because the current one often drops the internet connection. Don't know if its a problem with the modem functionality or something else. Will the older one serve better since i didn't have any problems with that one or will it be outdated? I only upgraded due it not having wireless capabilities. Otherwise it's fine.Or will I be even better off buying a dedicated modem? I really don't want to spend more money but if this is a far better alternative I guess i will.
EDIT: Ok so found out that I have to put the modem/router in bridge mode in order for this to be possible. However, looking up how to do this lead me to a dead end because i need to fill in some fields that i have no idea how to interpret.
VPI:
VCI: These 2 already came with presets. Should I just leave them?
Select DSL Link Type (EoA is for PPPoE, IPoE, and Bridge): Choices of EoA PPPoA and IPoA
Encapsulation Mode: Choices of LLC/SNAP-BRIDGING and VC/MUX
Service Category: UBR without PCR, UBR with PCR, CBR, Non Realtime VBR, Realtime VBR
[code]...
I have an old Compaq PC that's running Windows XP SP3 and for quite some time has not had problems with networking or using this wireless adapter. But not long ago the network interface disappeared and the adapter was now being shown in the Device Manager as an unknown device. If you pulled the adapter out and reinserted it you'd get a message on screen that would say something to that effect.
There are two computers next to each other that both use this exact same adapter and I've tried swapping them between the PCs to see if one adapter worked better than another. They both work in one PC and neither work in the PC I'm having trouble with.
I have a modem Scientific Atlanta 2100. I just installed windows 8 pro 64bit and when installing the driver to use the usb cable modem does not recognize it and simply not installed. I wonder if it is possible to use my usb cable modem or simply incompatible with my windows 8 64bit pro.
View 3 Replies View RelatedHave hooked up a DIR-825 to an iMac and it works well on 2.4GHz band. Having issues seeing 5GHz band as it comes and goes. Just today bought a DWA-160 USB adapter hoping it would connect the kid's PS3 to the 5GHz band but the PS3 wont accept or recognize either the DWA-160 or the 5GHz band.
Can't find any solutions in the manuals.Desperate for a fix as the wife and I want to be able to work on the 2.4GHz without being constantly kicked off by the kids on the PS3.
I have multiple computers on my network as well as cell phones logging in as wifi. At least once a day I have trouble or another computer has trouble getting on line through my network. I have to unplug my router and replug. Its as if it doesn't recognize the ip address until reboot.
View 1 Replies View RelatedDGL-4100
-> Wii
-> X360
-> PS3
-> DGS-2205 (gigabit switch in study)
*-> My PC
*-> Her PC
*-> DAP-1522
We're on the 192.168.1.x domain, and I've already hooked my PC up directly to the DAP-1522 and switched its IP address. So now, I can connect to it through the switch. I've renamed it, set it to WPA2 with a passphrase, and should be set to go. However, I can't get my laptop, IPod touch, or any devices to see it. Also, the DGL-4100 doesn't list it under the DHCP clients, but as I've got the DAP-1522 set to a static IP of 192.168.1.50.
Region : Brazil
Model : TL-WR470N
Hardware version: v2 Firmware version
latest (updated yesterday)
ISP:
My Iphone doesnt recognize my printer (HP Photosmart D110a) when I try to print something from it by AIRPRINT. After updated my printers and routers firmwares, the problem continues. Ive been read a lot and seems that the problem is caused by a problem with IGMP or Multitasking protocol.... But I dont find these in my routers page even after updated my firmware.
Region : Argentina
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version :
ISP :
I've been using this router for almost 2 years and it has been excellent but since 2 weeks ago it has stopped recognizing anything connected to the LAN port 1 and the WAN port, so it becomes useless as a router because I cannot connect a cable modem. The cable modem was tested successfully with a direct connection to a computer but it doesn't work with the router, and also ANYTHING you connect to these ports on the router is not detected, the lights do not turn on.
Set up DIR-615 to act as a router for my modem
View 2 Replies View RelatedRegion : Others
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 121225 Rel.37950n
ISP : UPC Hungary Ltd.
I can't able to recognize a system - all wifi clients lose connection. When this happens, the ping answer time rech the ~2000 times, then totally lose the connection, the SSID is dissapear - checking with my phone (android - wifi analyzer) and TL-WN822N USB wifi adapter (with the inSSIDer application). Meanwhile the cable clients and the WAN connections works fine, didn't experience anything.If I restart the wifi service with the hardware on/off button, it runs well for some time.This problem appeared when I used the two older official firmware too.
I tried the auto-chanel function width auto channel width, tried to manually set up one of the less interfered channels with both 20MHz and 40MHz channel width, but none of them bring the solution.The intresting thing is, if I change the router with an old D-Link DI-604, the signal is weak, but the wifi connection is stable, with the same TL-WN822N adapter.I tried to guarantee the router, but after two weeks, my reseller said, it looks ok, they - at the TP-Link service - didn't find anything.
I ordered the D-link DIR-815 router online at [URL], and I'll be receiving it this Monday which is the 14th, so I am asking my questions on here now, so I could be prepared.
1.) I don't have a wireless card in my PC, so I will be connecting wired to get WiFi via WAN and LAN ports, right? First before I forget, I have a Windows 7 32-bit desktop PC. We are working with a DSL modem residential line without phone line using a coaxial cable, and Ethernet cable from modem into the PC. connecting this D-link router to my modem and WiFi, and for me to use the WPA2 security?
2.) I have an iPhone 4 with Verizon. If I want to use my iPhone to get WiFi from the router, and turn off the Internet on my phone, and use WiFi only on my phone, how would this work?
I have a dir 655 coupled with a 320b modem for adsl. Now I must switch to VDSL. Can I use the router with a VDSL Modem? Which modem could be used ? I do not see dlink products ..
View 14 Replies View RelatedI have a buddy who owns a bar and wants to install a insecure wireless router for his customers downstream from his SBC Global ATT Modem/Wireless Router combo.
-Modem/Router Combo: Actiontec GT724WG
-Downstream Unsecure Wireless Router: D-Link DIR-651
He says has 3 static ips for the modem, and 1 of the network cables coming from the modem directly into the D-Link Router. I first attempted to just plug it into the uplink, and let DCHP do its magic, but I had no luck with that. I could connect to the router but it didn't have internet.
So I restarted the downstream router, and plugged the network cable into the 1st port, and suddenly I had internet on the wireless but it would constantly go up and down, and ping times were extreme erratic.
I have a D-Link 2740B with the 2 antennas and sloping black case and for some reason I now can't seem to login to the web GUI via 192.168.1.1. The modem is working OK but there is a setting I need to change.IE says "Internet Explorer cannot display the page"A friend then recommended trying Firefox. This worked the first time but now it is not connecting either. On http://192.168.1.1/ I just get a blank screen.I've turned the power off on the modem for 15 minutes and back on, and rebooted the computer.I've also tried turning Norton Antivirus & Firewall off but this didn't make any difference.I run Windows 7 Home Premium 64 bit with SP1.I've avoided resetting the modem as I am of the understanding that means I have to start from scratch with all the settings.
View 2 Replies View Relatedi'm trying to connect to my wii n my laptop. i have a cricket broadband hookup to desktop.
View 1 Replies View RelatedRegion : India
Model : TL-MR3220
Hardware Version : V1
Firmware Version : 3.14.2 Build 120817 Rel.55520n
ISP : Tata Photon Whiz
I just bought the TP Link MR 3020 and tried connecting my Tata Photon Whiz USB (Huawei EC121) modem with it. The TP Link cannot identify the modem. It goes forever into identifying mode. I next tried a Huawei E173 with Reliance 3g sim in it but again no results. The TP Link goes into identifying mode forever. I have installed the latest firmware for the device but am not able to set it up.
Region : UnitedKingdom
Model : TL-MR3220
Hardware Version : V2
Firmware Version : 121126 Rel.70304n (BETA)
ISP : T-mobile
there is a bug with MR3220 Router. I have HUAWEI E398 modem. It makes a LTE connections, everything works OK for half an hour, sometimes for a couple of hours, but then it (router)just unplugs modem after some time.ere is log:1st day 00:44:50DHCPNOTICEDHCPS:Recv DISCOVER from 8C:70:5A:8F:F0:E01st day 00:34:473G/4GNOTICEmodemUnplugedTime >=60s1st day 00:33:513G/4GINFO3G Modem is plugged out.1st day 00:33:493G/4GNOTICEdhcpcLteModemRelease 1261 sysCmd = ifconfig lte0 0.0.0.01st day 00:33:48DHCPINFOdhcpc_ipc_data_rcv_router 675 : current network type = 11st day 00:33:48DHCPNOTICEDHCPC Entering released state1st day 00:33:48DHCPNOTICEDHCPC Unicasting a release of 178.160.9.196 to 178.160.9.1931st day 00:33:473G/4GINFOprocess_msg 322 : call dhcpcLteModemRelease1st day 0:33:473G/4GINFOLTE MODEM = 0, status = 0, targetVendorID = 0x0, targetProductID = 0x0
1st day 00:33:473G/4GINFOLTE MODEM = 0, status = 1, targetVendorID = 0x0, argetProductID = 0x01st day 00:33:473G/4GNOTICEhandle_card start1st day 00:01:08DHCPWARNINGLTE Network connected.
i just installed a dlink dsl-520b modem. I installed it using the cd wizard without the router connected. Now when i try to hook the router [dir-655 rev B v2.10NA] up the world light is orange and i cannot get a connection. I tried running the wizard but it times out and says it cannot find the server. I used the reset button and that did not work. It says to use a PPoe connection and i have the right password but it will not connect.
View 4 Replies View RelatedRegion : Italy
Model : TL-MR3220
Hardware Version : Not Clear
Firmware Version : 3.14.2 Build 120822 Rel.57775n
ISP : Vodafone
Region : Italy
Model : TL-MR3220
Hardware Version : Not Clear
Firmware Version :
ISP : Vodafone
my MR 3220 cannot manage tp-link Ma180 modem. At start-up it tryes to identify the modem but after a while the status of the modem shows "Unplugged"
I already updated Router Firmware version. Firmware Version: 3.14.2 Build 120822 Rel.57775n Hardware Version: MR3220 v2 00000000 Signal strengts is weak but enough to access Internet when Ma180 is connect to my PC.
A piece of system log follows:
Index Time Type Level Log Content
9 1st day 00:17:00 3G/4G INFO LTE MODEM = 0, status = 3, targetVendorID = 0x0, targetProductID = 0x0
[Code].....
I was trying to access the modem router as the admin but AT&T seems to have a pain in the butt security system from me making any changes. I wanted to forward some ports to setup my Synology DS212j Network Attached Storage (NAS). I connected my d-link router to the already setup modem router which I am now connected to. I have to run off to school but I was wondering, would I be able to forward the port off my d-link DIR-601 and be able to host my NAS server off that?
I don't have too much in-depth networking experience besides setting forwarding ports, setting static IPs, but I can't do that since I am not the admin for the AT&T router. I figure the password for the AT&T router is just defaulted to admin or blank but I haven't had time to fully test everything out.
I moved to a new apartment and have to wait a month or even more to get my DSL internet, so I temporarily got myself a USB 3G device to have some access to the internet till I get my DSL line.
The USB acts as 3G modem for a single PC that's connected to it, what I want is to share that internet using my D-Link DIR-655 router so I'd be able to connect my iPhone and PS3 as well.
How to get that setup working as smoothly as possible would be great. DIR-655's default gateway is 192.168.0.1, and the auto DHCP range IIRC is 192.168.0.100 to 192.168.0.199.