I'm trying to track associations on one of my AiroNets (AP1041N) using the show dot11 associations command, but it does not show anything! e.g.AP1#show dot11 associations allAP1#show dot11 associations all-clientAP1#show dot11 associationsAP1# Is there something I need to enable in the configuration to track associations like this?
View 1 RepliesWireless is working ok on 1811W.Need to know from command output below what values are considered good for power and signal strenghts
1811w#sh dot11 associations all-client
Address : 40fc.894e.c48c Name : NONE
IP Address : 192.168.98.2 Interface : Dot11Radio0
Device : unknown Software Version : NONE
[code].....
Also what is Association ID mean in above output?
We successfully use this oid on our Aironet 1240 series AP's to list the dot11 associations to the AP:1.3.6.1.4.1.9.9.273.1.2.1.1.18 (cDot11ClientSubIfIndex).However, that oid does not work on our Aironet 1140 series AP's. Any equivalent oid?
View 0 Replies View RelatedMy 3502i suddently shutdown it's Radio interface and when I connect to it, I cans ee that the interface is shutdown. So tryign to enable it but the "configure terminal" command is not available. Is there any hidden command to go the priveledge mode?
______________
interface Dot11Radio0
no ip route-cache
shutdown
antenna gain 0
beamform ofdm
mbssid(code)
I have WLC 4402 working with AIR-AP1131AG-E-K9. Need to buy another pair. I looked to the side air-ap1041n-e-k9. Tell me whether or not the compatibility of the controller and the AP1041n? One more question. When buying in 1131 is still in the box and power cord to the point. The new 1041, the purchase comes with the point of the power cord?
View 13 Replies View RelatedI have a problem with my AIR-AP1041N-E-K9, i do not seem to get an ip-address assigned after a reset to factory defaults.I do see the AP with CDP:
Device-ID: ap
Advertisement version: 2
Platform: cisco AIR-AP1041N-E-K9
Capabilities: TransBridge IGMP
Interface: gi5, Port ID (outgoing port): GigabitEthernet0
Holdtime: 163
Version: Cisco IOS Software, C1040 Software (C1140-K9W7-M), Version 12.4(25d)JA1, RELEASE SOFTWARE (fc1)
[code]...
I also noticed that when i connect to the AP via console-cable, i can see the AP boot up in the console session, but then i do not get a login prompt, but it seems like the AP is responding; if i shutdown the interconnecting link between the switch and the AP, i do see log messages appearing in the console-connection.I have tried to debug on the Switch, but i need a password, so i can debug, which i do not have.,
How do you configure for standalone use. no documentation.
View 1 Replies View RelatedJust did a dot11 radio link test on a point to multipoint 1400 series bridges. how to read the results of the test?
View 9 Replies View RelatedFor WLC 5508 software version 7.0.235.0, which command is needed to get the WLC send syslog messages everytime a wireless client associate and desassociate?
View 2 Replies View RelatedI want to be able to send snmp traps to my NMS alerting our NOC to when we reach our configured max-associations on an ap. We currently use both 1130 AG and 1140-2N in autonomous mode, no controller. I have found a debug command "debug dot11 station connection failure" and the output of a test AP shows us the fact that the maximum number was reached. I need to find if it is possible to trap on such information.
View 1 Replies View RelatedI'm trying to get confirmation on whether you can have workgroup bridge mode on the 1040 series model.
The 1041N has the same IOS as the 1141/1241 and it has the settings are there, but I read somewhere on the cisco site that workgroup bridge is only supported on 1100 and 1200 series, is this correct or old information?
Scenario is: I have an existing stand alone 1041N AP, on the other side of the building I have a network LAN switch with a couple of PCs, instead of running cables I would like to add an AP as a bridge to link that switch and PCs to the network that the AP is plugged in to. I believe this is called Workgroup Bridge Mode. In fact there already is a cheap non-cisco wireless device doing this but it is unreliable.
I just placed an order for Two 1041N APs, do I need to change the order to Two 1141N instead?
Also even if the 1041N does not support workgroup bridge mode, can it still act as the ROOT Bridge and have 2 1141N APs configured in bridge mode connected to the 1041N?
I have a very special application where I need to connect as much as possible end devices to a single access point.The required data throughput per end device is very small - around 1 to 5 kbit/sec.I am using the Access Point Aironet 1242AG.
Questions :
1. What is the maximum number of simultaneous users that can be connected to a Cisco Access point, is it 255 or can be more ?
2. If I define multiple SSID’s, what if the total numbers of users that can be connected to a Cisco Access point
3. I there a simulator tool that can be used to simulate multiple wireless connections to an AP
4. Have anyone tested so many users connected to 1 Access point ?
some days ago I succesfully converted AIR-LAP1041N (lwapp) to AIR-AP1041N (autonomus).I used c1140-k9w7-tar.124-25d.JA1.tar which is available to download in Download Software Section for this AP.But there are any autonomus to lightweigt firmware for this AP.I tried to use c1140-rcvk9w8-tar. 124- 21a.JA2.tar for 1140 but AP hungs after that. How can i back to LWAPP version in 1041?
View 7 Replies View Relatedis there a way to get traffic and client access/associations data with WCS for each AP of a centrally managed WLAN?I manage a campus WLAN with a 4402WLC (software version 6.0.188.0) and a WCS version 6.0.170.0 .WCS provides me detailed information on a client basis: I'm able to know the association history of each client currently connected, both which AP the client has connected to, and how much traffic the client has generated/ received for each connection.I hadn't find a way to get the same information on an AP basis. Namely, which clients have been connected, and how much traffic has been transmitted per time slot. I suppose this is just a matter of making a different query to the WCS database, since the data are the same used for providing the information on the client association and traffic history. Though, I haven't find a way on WCS to get this information.
View 2 Replies View RelatedI've setup the following AP1041N configuration, but for the life of me - the radio will not enable.
++
sho conf
Using 3234 out of 32768 bytes
!
[Code]....
I'm using aironet 1210, 1130, 1100, 1040 autonomous mode, in a University campus network with thousands of daily user.We're using RADIUS authentication and AES/WPA2.In the past, there were some major issues with traffic (broadcast / multicast) in the wireless networks, that would spread all around the campus causing excessive processing at the access-points.To solve the problem we decided to implement access list at the radio interface to drop all the unwanted traffic. [code]
I'm pretty sure this is caused by the ACL (I've tested removing the ACL and the issue never occurred) but I can't just get ride of it.
Any alternative way to drop broadcasts?
I need to configure public and private wireless access using an ASA 5505 and an Aironet AIR-AP1041N-A-K9. I need to be able to do this via ASDM and http if at all possible. I simply do not have the time to learn hundreds of lines of arcane CLI code. The Aironet connects to the ASA successfully, and receives an IP. I can then connect to the AP wirelessly, but do not receive an IP. I have setup a second SSIDVLAN on the AP, and can't connect to it at all.
View 4 Replies View RelatedWe got a 3310MSE that does not track clients.,rogues etc for some reason.
- there are no firewalls between PNCS and MSE
- clocks are synced up with NTP
- CAS is running on the MSE
- I have added controllers and a test site with clients and is synced up with the MSE.
- Have enabled tracking under tracking doe clients and rogues excluding adhoc rogue APs -we only have 100 element license.
The only other thing worth mentioning is that MSE is running version 6 firmware and the controllers are 7.0.220 but I do not think this should prevent MSE from tracking devices. [code]
I am doing support for a library that has 2 WAP2000 devices that have no security. These are for the patrons to connect to the internet at the library. They want to track how many people are connecting to the internet. Can I log how many computers connect to these access points or get another WAP that will track how many computers connect to the internet?
View 1 Replies View RelatedI have configured a vlan interface on a 3750 switch. there is aprox 4Mb active traffic flowing through the interface, but when I do a "show interface vlan (vlanid)" the output show zero bits in and zero bits out. Its a typical L3 config with one IP on the vllan interface acting as the gateway for the VLAN devices. Is this a normal behaviur ? and if so is there any way to get the traffic in/out stats. The end PC/devices are connected to this switch via an L2 TRUNK and I dont have access to the L2 switch on which the actual devices connect. so cant get the real time stats of those interfaces.
View 2 Replies View RelatedHow to understand "show sessions" and "show connection" commands? And what is the difference between the two?
View 2 Replies View RelatedFacing issue with 2960G switch , where its do not display "logging trap informational " in show running and show startup .where its showing all other levels from 0 to 5 and 7 after configuration and save commands. [code] after config getting saved , it do not shows in show runn or in show startup while for all other levels it do show the config lines .I tried the same on 12.55.SE release also but its same results . Is this a limitaion of this platform, is there any doc explaining the same for reference. [code]
View 1 Replies View RelatedI have an MSE 3355 running 7.4.100.0, Cisco Prime Infrastructure 1.3.0.20 and 6 wism2 running 7.4.100.0. MSE was correctly added to Prime and assigned to maps and controllers. Context Aware Service is Enabled and Up and I have a permanent license installed with a limit of 3000 elements. The appliance is not able to perform client or rogue tracking. This is what I see under Services->Mobility Services Engines->Context Aware Service->General:
Version7.4.0.38 Operational StatusUpNumber of Tracked Wireless Clients0Number of Tracked Tags0Number of Tracked Rogue APs0Number of Tracked Rogue Clients0Number of Tracked Interferers0Number of Tracked Wired Clients0Total Elements Tracked0Tracked Elements (Wireless Clients, Rogue APs, Rogue Clients, Interferers and Wired Clients) Limit3000Tracked Tags Limit 3000
I have a cisco 1760 with running VIC-2FXO (working fine). I'm now trying to replace that line with an ISDN line through a VIC2-2BRI.
View 4 Replies View RelatedI am looking a solution to track login detail and visited web site on our public wireless network.We are using Cisco Wireless LAN controller 4400 series.
View 3 Replies View RelatedI have a WRT160N router. Are there any network software packages out "there" than will allow me to track the total traffic on this device?
View 1 Replies View RelatedIm looking for some software to monitor general info on the computers in the office. I would like to be able to service a computer and be able to pull up service notes, info on hardware and just be able to keep track of what we have been doing to all of the computers
[code]...
Trying to implement PBR in N7K? I found that there is not track mechanism can use in "set next-hop ip", so if the next-hop is unreachable that the route might be died.
View 0 Replies View RelatedI was just brushing up few things in GNS3 and after setting up an SLA.Now when I want to set the track ip I get not option for sla why??I am running c3725-adventerprisek9-mz.124-15.T5 shouldn't it be available?
View 2 Replies View Relatedi installed the Cisco Prime LMS widget and see there is a choice to search by username and hostname and phonenumber (for IP phones?) how can this be set up?
View 1 Replies View Relatedi have a 881G and an IP SLA icmp configured. (ip sla 1). I can get the status of it by the OID:
1.3.6.1.4.1.9.9.42.1.2.10.1.1.1
But, on the same router i have a track 1 for the SLA 1 and a track 2 monitoring track 1 with threshold . What i want, is to get the OID of track 2 so i can get the status of it. Which OID is that?
My upload is very high but I dont use any P2P programs. Can I track what is being uploaded?
View 2 Replies View RelatedI have an 877 router which has a DSL WAN interface. The DSL service at this site is unreliable, so the company have purchased a separate 3G router to be used as a backup. This device maintains 3G connectivity at all times and has a static IP on the internal subnet (for arguments sake let's say 10.0.0.253).
What I want to do with the Cisco router is to track the DSL interface and if it is up, install a default route pointing to it. If it is down, I want the default route to be the 3G router.
I am thinking the best way to do this is to set up a track and then set 2 default routes; one which is installed if the tracking is up, the other has a higher admin distance and points to the 3G router and thus should only be used if the track is down. For example:
track 10 interface Dialer0 ip routing
delay down 30 up 30
ip route 0.0.0.0 0.0.0.0 Dialer0 track 10
ip route 0.0.0.0 0.0.0.0 10.0.0.253 100
Is this likely to work or is there a better way to do it?