Cisco :: Aironet 1210 - Sleep Mode Causes 0.0.0.0 Dot11 Association
May 20, 2012
I'm using aironet 1210, 1130, 1100, 1040 autonomous mode, in a University campus network with thousands of daily user.We're using RADIUS authentication and AES/WPA2.In the past, there were some major issues with traffic (broadcast / multicast) in the wireless networks, that would spread all around the campus causing excessive processing at the access-points.To solve the problem we decided to implement access list at the radio interface to drop all the unwanted traffic. [code]
I'm pretty sure this is caused by the ACL (I've tested removing the ACL and the issue never occurred) but I can't just get ride of it.
Any alternative way to drop broadcasts?
View 6 Replies
ADVERTISEMENT
Oct 18, 2012
We successfully use this oid on our Aironet 1240 series AP's to list the dot11 associations to the AP:1.3.6.1.4.1.9.9.273.1.2.1.1.18 (cDot11ClientSubIfIndex).However, that oid does not work on our Aironet 1140 series AP's. Any equivalent oid?
View 0 Replies
View Related
Apr 26, 2012
I Buyed a new laptop yesterday(24-04-2012) so original W7 and i updated everything incl drivers and everything was great and i let the laptop on when i Was going to sleep and my wireless and lan internet did fine.. But then.. when i wake up suddenly it tells "No Connections Are Available" and i cant find any wifi's anymore + lan does not even work, but the adapters are both working fine it says + they are up to date, the router is fine cuz i have lan on pc and wifi on samsung galaxy, everything about wifi is on incl the button on the laptop..I only have 1 antivirus or so program and i have a red cross @ network and sharing settings?Network adapters (They both work): Atheros AR9285 wireless adapter & Realtek PCIe GBE family controller (both newest drivers installed)
View 3 Replies
View Related
Mar 15, 2011
While watching movie - screen goes blank and 'error mssg ' states error is preventing slide show from playing'
View 1 Replies
View Related
May 7, 2012
Have already checked in the Device Manager if the �Allow this device to wake the computer� is unchecked.What do I do to bring the sleep mode back without turning off the file sharing (if file sharing caused the problem)?
View 1 Replies
View Related
Apr 13, 2012
So whenever I put my desktop to sleep and then turn it back on, I cannot connect to the internet. My laptops are fine and can connect to the internet w/ the wireless however.When I have windows diagnostic run a troubleshoot and repair, it tells me it can't communicate w/ the primary DNS server and that resetting the Local Area Connection will fix it (And it does).If I restart the computer, it seems to fix this problem as well.I don't get why it can't communicate w/ the DNS and that I have to manually reset the LAC everytime I turn on the computer from sleep mode.
View 3 Replies
View Related
Jun 28, 2011
I used to have ATT DSL but we recently switched to U-Verse. I have a Trendnet TEW-452BRP 54g wireless router than was handling the PPPoE function. It was set to work flawlessly with my wireless cards. No dropped connections, speed or security issues. It always connected quickly from wake up and on start up. Now we have a 2Wire i38HG wireless router/gateway and it's been difficult to properly set my network up as before. I use the Trendnet behind the 2Wire as my wireless router. Took me a while to figure out what to do, but DHCP is disabled on Trendnet so 2Wire does what it needs to. This option works fine for me. The only problem is that at first my wireless card would not automatically connect to the network through the Trendnet when it is in range like I had it set to do previously. When I would force it to, after 3 times it would magically connect on it's own. I made some changes in the Trendnet (Mainly disabling dynamic DNS and NAT) and that seems to have made a difference. To be honest, I don't know if that is significant or not or if it actually made a longterm difference but it seems like it has. So my problem is now that when I put my laptop to sleep and have it wake up, it does not automatically reconnect. It takes about 2 minutes then it does on its own. I read the event viewer and this is the info it gave me - Your computer was not able to renew its address from the network (from the DHCP Server) for the Network Card with network address 0x0018DE0682D8. The following error occurred: 0x79. Your computer will continue to try and obtain an address on its own from the network address (DHCP) server.
Level - Warning
OpCode - IpLeaseRenewalFailed
Source - Dhcp-Client
Then after 2 minutes -
Your computer was not assigned an address from the network (by the DHCP Server) for the Network Card with network address 0x0018DE0682D8. The following error occurred: 0x79. Your computer will continue to try and obtain an address on its own from the network address (DHCP) server.
Level - Error
OpCode - IpAddressNotAssigned
Source - Dhcp-Client
After this, it connects by itself. I don't believe I have configured the 2Wire or Trendnet properly, so I need some guidance and suggestions on this matter.
Laptop - Intel Core Duo 1.66ghz, 2gb Ram, Win7 Professional with SP1, Intel PRO Wireless 3945ABG
2Wire - 192.168.1.254
Trendnet - 192.168.1.1
- I did not change the IP of the Trendnet and I am not sure if I have to.
From the 2wire - Private Network
Router/Gateway Address192.168.1.254
Subnet Mask255.255.255.0
Private Network DHCP Info
Range192.168.1.64 � 192.168.1.253
[code]....
View 10 Replies
View Related
Jan 9, 2012
I have TP Link TL-WR740N , Firmware Version: 3.12.11 Build 110915 Rel.40896n . All working fine , but one problem whan I put my PC to sleep mode , and roter stay working , after when I awake PC it lost connection with router !
View 2 Replies
View Related
Apr 30, 2013
I am completely baffled by what is going on, on our network. We have four HP C4005 Printers. All of them connected to different switches around the network. About every 1-3 hours they all give the error 49FF09 (which is pretty vague, basically a network connectivity issue). Have to reboot to get rid of the error, then it will work again for an hour or so and give the same error (whether print jobs have been sent or not). This started a few days ago out of no where.
I am starting to think its an issue with the network, because they will all go offline at the same time. If I run a constant ping to them, they will all go offline at the same time and return the error. We use all cisco equipment. If I check the port statuses they all say up 100 full with no errors.
I have tried disabling sleep mode on the printers, turned off multicasting, updated firmware for printer and for jetdirect, and used different drivers.
View 19 Replies
View Related
May 15, 2011
I am trying to download large files which are taking about 3-8 hours to download. I don't have that much time, so I have to put my computer into sleep mode. Now, the problem is, I put it into sleep mode, turn it back on, Chrome says the downloads are finished. I open one of them, and it says the file is corrupt.
View 14 Replies
View Related
Apr 1, 2010
I have a new Linksys E3000, 2 wired disktops (1 windows 7, 1 windows vista), 2 wireless laptops (both windows Vista), whenever the computers power down into sleep mode and are woke up, I have lost my connections to the router and I am forced to restart the computer. I've been told by one person that this is a problem with vista and windows 7, but wouldn't that have been a problem with my old router also?
View 9 Replies
View Related
Jul 21, 2012
indows 7 Studio 1458 Crashes when entering Sleep Mode
View 2 Replies
View Related
Feb 10, 2013
I have a Dell Inspirion M5110. Windows 7, 64 bit.
When ever I open the lid to the laptop it takes 5-10 mins before it will automatically connect to a network. Diagnose this network does not find anything, nor provides any troubleshooting. Typically if I open the network connections center and disable the wireless, let it sit for 30 secs or so, and re-enable, it will finally connect.
I know it's not my router, as the laptop does the same thing at work, and multiple different friends house.
I've confirmed that DHCP is set to automatic connect. I've also checked Device Manager/Network adapters/ and unchecked the box "allow the computer to turn off this device to save power"
View 3 Replies
View Related
Feb 25, 2013
I use a WUMC710 bridge with desktop PC and a Printer connected to it. When those two devices have been inactive for a while the bridge goes into sleep mode and loses the connection Back to my EA6500. Trying to print something from wireless devices connected to the 6500 elsewhere in the network doesn't "wake up" the bridge. Ihave to unplug the power supply and restart it.
View 2 Replies
View Related
Feb 12, 2012
I have a Dell E4300 with a 1510 wireless mini adapter running windows 7 pro with a netgear WNR3500 router running wireless N protocol. I have my laptop setup to sleep when lid is closed. When it awakens the wireless connection will not automatically reconnect and I have to manually select the SSID and connect. It will also reconnect if I use the network troubleshooter. The problem does not happen if I reboot the PC or start from a power off situation. I have the latest Dell driver and I am running the DWLAN utility.
View 3 Replies
View Related
Sep 12, 2012
I have some old 1231 APs in the school in which I work.I would like to create a local network (no LAN, no internet, just a point to point wifi connection) managed by the access point (in DHCP).That's because we have an apple TV connected to a projector and some ipads. My idea was to put the devices locally in the same closed network for share via AIR Mirror the ipads on the apple TV.
View 3 Replies
View Related
Feb 18, 2013
I have to set up the AP in a standalone mode to support voice and data traffic through the wireless network. for this, i was trying to look for the config guide so i know how to go about it, but all the doc was refering to controller based setup. i followed this link URL
I have never worked on wireless in a standalone mode, so this is the first time i will be doing it.
View 22 Replies
View Related
Sep 14, 2011
I just received a Cisco Aironet 1130 AG wi-fi router to configure and when I entered the router through console, I am not able to get into config mode. It says:
AP588d.09a7.93e4#conf t
^
% Invalid input detected at '^' marker.
Also,
AP588d.09a7.93e4#sh start
startup-config is not present
Also, this is what I see in my flash:
AP588d.09a7.93e4#sh flash:
Directory of flash:/
3 -rwx 217 Mar 01 2002 00:07:10 +00:00 env_vars
4 drwx 128 Jan 01 1970 00:02:03 +00:00 c1130-rcvk9w8-mx.bin
I need to configure this device and set up for wi-fi access in my organisation network.
View 2 Replies
View Related
May 29, 2013
I bought a Cisco Wireless AIR-CAP2602i-E-K9 and have some practice on Cisco routers, but can not log in "Global Configuration Mode", not existe the command "Configure". How active configuration?
View 10 Replies
View Related
Sep 14, 2011
I just received a Cisco Aironet 1130 AG wi-fi router to configure and when I entered the router through console, I am not able to get into config mode. It says:
[code]....
View 9 Replies
View Related
Mar 13, 2013
we have 1262 (AIR-LAP1262N-E-K9) and we dont have WLC..and i want to convert it to Autonomous mode..i did the below steps... with using this file (ap3g1-k9w7-tar.152-2.JB.tar) download it from Cisco site. Step 1 The static IP address of the PC on which your TFTP server software runs should be between 10.0.0.2 and 10.0.0.30. Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated. Step 3 Set the timeout value on the TFTP server to 30 seconds. Step 4 On the PC where the TFTP server is located, perform these steps.
View 48 Replies
View Related
May 13, 2013
Do we have Option to add MAC address of specific laptop or Mobile to connect to the Access Point in cisco Aironet AP 1260 series in Autonmous mode
View 4 Replies
View Related
Mar 17, 2012
How can I enter into "interface configuration" on Aironet 1130AG, AIR-LAP1042N?When I put following commands in enable conf tinterface Dot11Radio1 but, it fails and I cannot enter into "interface configuration".How can I do this ?The reason why I enter into conf tinterface Dot11Radio1 because I want to disable cdp via CLI ( serial console).
View 9 Replies
View Related
Jun 11, 2013
I have an Aironet 1250 AIR-LAP1252AG-A-K9 I am having issues with, and I am hoping for some direction on how to resolve them. I understand this question has been posted many times many different ways, but i have no luck unfortunately. Here is where I am: I can terminal into the AP, which has been set to factory default, with the username and password and enable password of Cisco. Once I am in the enable mode, I get lost.
Usually there would be an option to go to config. t, and work from there, but this AP does not have that option, Actually if I do a ? at the enable prompt, the commands list only starts with the letter C; but none are config.
I also cannot get into the web interface of the AP. The AP gets a DHCP IP from my DHCP server, (192.1681.128/24) but I cannot get into the web interface using the IP it gets from DHCP. The page never comes up. To add to the confusion, I cannot turn off the CLI event logging, although I enter the command "no debug all". Maybe I am off on what to put in. Nonetheless, it drives me crazy with messages every two seconds as I am trying to type while attempting to figure things out.
Overall, from reading the forums and doing Google searches, I am going on the assumption that the AP is now in lightweight mode, as opposed to autonomous mode, which is where I want it to be. I have tried the method of updating the firmware to the autonomous firmware from Jan 2013 for the AP. I use the TFTP method as I have found here on the forums a few times; I hold the mode button down while applying power to the AP, let the system LED turn red and release the button so the TFTP process can go through, but nothing changes.
I have the AP powered from a gigabit POE switch. The computer I am using for the TFTP is on the same sub net as the AP. I have tried using 10.0.0.6/24 for the computer with the TFTP on it, made sure the view all file extensions option was checked, and renamed the firmware to the .default extension-still nothing updates.
I also noticed that once I hold the mode button down for 20-30 seconds then let it go, the CLI output says the AP it is on the 10.0.0.x sub net, but I cannot ping the computer with the TFTP program on it. If i try to, it get a "Command not supported" message. So I will go on the idea that this is most likely why I cannot do a TFTP update.
About 30 seconds after I release the mode button and the AP boots, it will say it has a 10.0.0.x IP address, then it starts going crazy with messages that it cannot find a DHCP server.
View 3 Replies
View Related
Dec 14, 2011
I have about 50m between switches. When using Cat6 I could not get a connecting between switches but when I use Cat 5E I get a connection. The switches are D-Link DGS-1210-10P switches. Why do the Cat6 which is suppose to be superior to Cat 5 not getting a connection.
View 1 Replies
View Related
May 21, 2012
Is it possible to move my phone card from my XPS 1210 to my XPS L502X ???
I would like to be able to hit the road online again
View 1 Replies
View Related
Dec 15, 2012
My 3502i suddently shutdown it's Radio interface and when I connect to it, I cans ee that the interface is shutdown. So tryign to enable it but the "configure terminal" command is not available. Is there any hidden command to go the priveledge mode?
______________
interface Dot11Radio0
no ip route-cache
shutdown
antenna gain 0
beamform ofdm
mbssid(code)
View 10 Replies
View Related
Aug 18, 2011
..how many PCs are allowed to connect to the printer via printer sharing? Is it unlimited?
..the printer are connected to the main PC
printer : Canon Laser Shot LBP-1210
View 2 Replies
View Related
Jan 30, 2013
I'm trying to track associations on one of my AiroNets (AP1041N) using the show dot11 associations command, but it does not show anything! e.g.AP1#show dot11 associations allAP1#show dot11 associations all-clientAP1#show dot11 associationsAP1# Is there something I need to enable in the configuration to track associations like this?
View 1 Replies
View Related
Oct 23, 2012
Wireless is working ok on 1811W.Need to know from command output below what values are considered good for power and signal strenghts
1811w#sh dot11 associations all-client
Address : 40fc.894e.c48c Name : NONE
IP Address : 192.168.98.2 Interface : Dot11Radio0
Device : unknown Software Version : NONE
[code].....
Also what is Association ID mean in above output?
View 5 Replies
View Related
Sep 11, 2012
Just did a dot11 radio link test on a point to multipoint 1400 series bridges. how to read the results of the test?
View 9 Replies
View Related
Oct 21, 2010
Had some problems with the association of the MSE with the WCS.Licenses already loaded context aware and WCS-PLUSThe two machines are within the same network segment WCS (10.16.0.28) and MSE (10.16.0.89), including IP connectivity exists and which tests ping.When I do a / etc / init.d / mse status throws me the following error:
root@xxxxx# /etc/init.d/msed statusSTATUS:MSE Platform is up, getting the statusUnable to get MSE status. Error: (400)Bad RequestRetrying status fetch -Unable to get MSE status. Retrying status fetch -Unable to get MSE status. Retrying status fetch -Unable to get MSE status. Retrying status fetch -Unable to get MSE status. Retrying status fetch -Unable to get MSE status. Retrying status fetch -Unable to get MSE status. Retrying status fetch -Unable to get MSE status. Retrying status fetch -Unable to get MSE status. Retrying status fetch -Unable to get MSE status. Retrying status fetch -Unable to get MSE status.
[code]......
View 3 Replies
View Related
Apr 11, 2012
Quick question about the association web interface tab on a 1140. I have noticed that the Device Type shows as "unknown" and the Name shows as "NONE."
View 1 Replies
View Related