D-Link DIR-601 :: EW-432BRP Not Working With Dish Network IPTV
Jun 6, 2012
I purchased IPTV set-top box from Dish Network (which in turn uses NeuLion services). The set top box works out of the box with TrendNet TEW-432BRP, however the set top box seems to reboot every time I try to launch a channel.The set top box is connected to LAN port 2/DLink is configured to reserve IP address for the set-top box based on its MAC address. The set top is also within its own DMZ so that it does not interfere with firewall settings.
View 1 Replies
ADVERTISEMENT
Jan 31, 2011
After upgrading firmware from ver 4.00 to 4.11 I can't watch IPTV anymore with VLC. With version 4.00 IPTV works over router (wireless or cable) fine but because of some disconecting trouble I upgraded to ver 4.11. Setup is the same as it was in ver 4.00 including Multicast parameter.
View 5 Replies
View Related
Dec 13, 2011
I am trying to connect my DishNetwork DVR up via a wireless link to the E3000.My home network consists of a Linux Server acting as a router/gateway for a DSL link, with several pc's (XP/MAC/Linux) connected on a local 10/100 lan.The existing lan addressing scheme uses static IP's and the DVR requires a DHCP link.I thought the E3000 would solve that issue by using it's DHCP server capability to host the DVR wirelessly and integrate it into the rest of the lan.I set up the DHCP and reserved an IP address, which the DVR pick's up just fine, but although I can ping the gateway and DVR in both directions, I am unable to access the internet.I've tried to set up a static route, but I think I'm not doing it correctly. [code]
View 9 Replies
View Related
Nov 28, 2012
I have e1200 v1 with last firmware 1.0.03. Device using as AP/switch (no WAN port installed). When I open the TV chanal (239.0.1.3) the pictures 1 sec good and then stoped, device not responding. When TV off, 3 sec later internet works and device up.
View 4 Replies
View Related
May 15, 2010
Upgrading the firmware from 1.11EU to 1.21EU and 1.31EU has introduced a problem with multicast (IPTV) streams. I have enabled multicast streams and it seems the router no longer forwards a specific address range, in my case 239.139.128.* on port 1234.
I have checked: Streaming from 233.81.233.* works in 1.11EU, 1.21EU and 1.31EUStreaming from 24.1.3.* works in 1.11EU, 1.21EU and 1.31EUStreaming from 239.139.128.* works only in 1.11EUUsing IGMP proxy on Linux I have checked the stream at 239.139.128.* are available as to be sure the DIR-655 is not forwarding them. I see a lot of forum messages stating IPTV streaming is broken since firmware 1.11. It is however working for me in 1.31EU but only for certain address ranges. Can anything be configured to allow 239.139.128.* to work? Because my TV provider uses the 239.139.128.* range for half the IPTV channels I need to get this working.
Related to this, is there page listing known bugs for the DIR-655 and roadmap for future firmware releases?
View 2 Replies
View Related
Jan 14, 2012
The internet is fine until I turn on my laptop. After this on one can connect to the internet. It goes back to normal when I turn off the laptops wireless capabilities with fn F12.The router is a trendnet TEW-432BRP
View 3 Replies
View Related
Jan 30, 2013
i have a campus network with 2 core Cat6500 and multiple 4500 series distribution switches plus 2960 series access switches,we have deployed IPTV system in the network but currently 50 TVs are working through sattelite stream from streaming server Cisco's DCM 9900.we are planning to add more 300 TVs in the network and i am wondering that when all of them will be deployed then what will happen for switches cpu utilizations when all the Tvs will be running on the same time with different different channels.
View 1 Replies
View Related
Jul 8, 2012
recommend a cisco core switch and access switches in IPTV network infrastructure?I was ask to implement a network for IPTV system but i don't have idea what will be the model i will use.
Core Switch = Cisco 4503
Access Switches = Cisco 3560X
View 3 Replies
View Related
Nov 19, 2012
i want to know the difference in features between 3.5 feet dish antenna and 4.0 feet dish antenna.can any one let me know that size of the dish really matters.
View 2 Replies
View Related
Jan 23, 2013
I just received a Dish TV slingbox and I am trying to set it up to work with my E2500 wireless router.I'm told by Dish that I need to open up ports 80, 443 and 5678. I have Comcast as my ISP.I've gone into the Single Port Forwarding option in the Router Browser interface and for each of the 3 above listed ports have enter this info (using 80 as an example):
External Port: 80
Internal Port: 80
Protocol: Both
To IP Address 192.168.1.2
Enabled is checked
I have confirmed that UPnP is enabled. I am running firmware 1.0.07.I have seen examples on the web where the last digit of the "To IP Address" is left blank, but that is not an option, as I'm forced to enter a number between 1 and 254. 1 will not work as it is my router's IP Address.
View 2 Replies
View Related
Jul 12, 2011
RDP (port 3389) is not working on D-Link network - is there a setting in the d-link to allow this?
View 4 Replies
View Related
Jun 9, 2011
the Dlink Network Monitoring widget just shows: IP Address error?I'm on DIR-655 Rev_B hardware and 2.01 firmware.
View 1 Replies
View Related
Nov 13, 2012
I bought the DIR-655 last year and till within warranty. Yesterday, I lost the wireless network on my laptops but internet was working. I contacted the d-link support and during the process of troubleshooting the problem, the internet connection was also lost. I followed all instructions given to me by d-link teams that spoke with me but the problem was not resolved. I tried to call the d-link support but my calls were ignored . Up till now, the wireless and internet connections through DIR-655 are not working.
View 5 Replies
View Related
Jun 20, 2011
I have a DIR-655 with both wired and wireless connections. Yesterday, network stopped working on one wired machine while using it to surf the internet and a 2nd wired machine has not worked in 3 weeks after moving it from one room to another. Wireless connections are working fine.
-2 wired systems (Windows 7 and Windows XP), both stopped working
-2 wired Xboxes - working fine
-2 laptops, wireless working fine
-1 smart phone, wireless working fine
I've power cycled my DSL modem and DIR-655 multiple times.Power cycled computer multiple times. Tried Win7 built-in diagnostics.Tried setting up static IPs.Tried filling in preferred DHCP server address.Disabled Windows firewall. [code]
View 4 Replies
View Related
Dec 30, 2012
Region : Poland
Model : TL-MR3220
Hardware Version : V1
Firmware Version :
ISP : Bite
Router TL-MR3220 works well on 3G network, but is not works 2G (edge) network. 3G network is not suported in my location, only 2G. My modem is Huawei E 173. In location 2G network Router show: 3G/4G USB Modem: Unplugged.
View 3 Replies
View Related
Oct 16, 2011
I was working on the computer and internet just stopped, checked the router and it doesn't show up in air-port pref on my Macbook Pro anymore. It was still on my iPhone, and then a few minutes later disappeared from my iPhones network as well. I've tried hard resetting etc, network name doesn't show up anymore, on ethernet to the modem now but tad uncomfortable sitting on the living room since I have the router and modem in my entertainment center.
All the lights work fine, and it lights up like normal but network went "poof".
Typing in ip of 192.168.0.1 just says google chrome cannot connect to that page. I had to play with my Mac for awhile as it wouldn't connect by ethernet till I figured out I had to uncheck passive FTP from Proxies.
View 4 Replies
View Related
May 16, 2012
So I have bought myself a DCS-2121 with firmware 1.05, 4630. Everything works fine except that the camera does not seem to adhere my settings on the snapshots page. At average, it seems that only one image is sent to my FTP-server regardless of the interval parameters.
View 2 Replies
View Related
Dec 27, 2010
my DCS-2121 :
The scheduled recording or scheduled snapshots is not working. I am running the camera standalone and using the web based configuration, storing the images or avi's on a ftp or samba server.
No matter what i specify, it records when triggered (by motion in my setup). All the other settings like, samba, ftp, video, motion detection, and so on is working fine - but I can't configure it to only record like between 10-16 every day. It records all the time - no matter what I select and what I enter in the schedule scheme.
View 2 Replies
View Related
Sep 10, 2012
The other day I went to a friends house, came back home, booted up my PC, and my wireless network adapter wasn't working. I've tried everything to fix it.It's a D-Link DWA-525 802.11n Wireless PCI netowrk adapter. On device manager it just says 802.11 Wireless LAN Card with a yellow exclamation next to it. And when I check what the error is, it's either error 31 or 52 at different times, depending what I've tried to do to fix it.I tried downloading the driver for it off the D-Link website, nothing happens at all when I install it. I tried taking it out of my computer and plugging it in. I tried enabling it and disabling it on device manager.I noticed one thing, when it's in my computer the green light at the back that says activity next to it isn't on.
View 10 Replies
View Related
Mar 22, 2013
I was using Remote Desktop between two home computers hard wired through the router and a switch. Now after upgrading to firmware 1.35 I can't get remote desktop to connect. I get an error that I may not have permission, etc. I have the DIR 655 ver A and am running Windows 7 professional on both computers.
View 5 Replies
View Related
Apr 26, 2011
My topology is a physical ring, and I need transfer IPTV signal to all site along the ring.For example:
A (headend)--- B --- C --- D
|______________________|
Note: -----: have spoke-mesh defination
_____: no spoke-mesh defination to prevent loop
So, with MPLS/VPLS I can implement it. With spoke and mesh defination, the traffic can transfer form A to B, C or D as drop-continute action in ring topology (between different VC). Everything is good, FRR can work very fast. But when the topology have a failure link, for example the link between B and C, at that time the traffic will go from A to B then B come back to A and A --- D ---C. This action is so stupid, because it can increase delay, jiiter in network. On the other hand, when the node failure ( B failure), C will loss the IPTV signal, even the link from A--D--C always good.
View 6 Replies
View Related
Dec 22, 2011
i am signed up for an IPTV service. my service provider set up their own hardware including a reciever and a wireless modem. but their wireless modem has weak signal and i cannot connect to it using my computer in the other room. so i wanted to set up my WAG54GP2 modem to use with IPTV service. but i couldn't. i have followed the instructions described there:
[URL] (support page for some other IPTV provider, i guess)
so, i have checked the configuration details of the other modem which is provided by the IPTV company and found out that encapsulation mode is selected as "DHCP" instead of "Bridge mode only". But my linksys modem does not have an option named "DHCP". so, does it mean that it is impossible to use IPTV with my WAG54GP2 modem?
View 2 Replies
View Related
Mar 17, 2013
Not far ago I purchased Cisco e1200. All my attempts to set up the iptv thru wifi failed. Nevertherless iptv works fine when I insert LAN cable directly into my laptop. On WRT320N does not work. Firmware is Ver.1.0.03.
View 9 Replies
View Related
Oct 25, 2011
Today has bought a router. Before it at me was D-link Dir 320. IPTV on DIR 320 worked perfectly. On WRT320N does not work. Firmware has updated to Ver.1.0.04 build 1. Prompt that it is necessary to make?
View 5 Replies
View Related
Aug 20, 2011
I've got an IPTV network with Bell FibeTV with Motorola VIP1216 (the DVR master) and VIP1200 (slave) cable boxes. All the coax cables in my walls form a wired ethernet network instead of a cable TV network. To get better wireless coverage in my home, I've set up routers as wireless access points at each of the cable boxes. Essentially I've plugged the router into the ethernet bridge of the cable boxes, and disabled DHCP and gave it a static IP and did all things I needed to do to disable all the routing capabilities and make it into a switch (here's what I did, step by step: [url...]). So when I go from one room to another, I just select a new wireless access point to get maximum signal strength and speed.
View 6 Replies
View Related
Feb 23, 2011
I've bought a E3000 as replacement for my Linksys WRT350N router.Just upgraded the firmware to version Ver.1.0. 04 (build 6).I use aonTV - an austria IPTV service (Multicast via UDP) - an this worked with my old WRT350N (hw version 1) consistantly well. I hardly had to reboot the router to get the multicast stream.With E3000 I checked the option that it should not filter any multicast traffic - when I reboot the router it works for some time - but after some hours it does not work anymore? I want to watch TV via my HTPC connected via GigaBit Power to the E3000.
View 3 Replies
View Related
Mar 18, 2012
I have bought Linksys E 4200. I'm connected up by protocol PPPoE by my provider, but IPTV doesn't work on my computer.I use the program IP-TV Player and/or VLC Player and both don't work. I only see the list of channel, but any channel doesn't load. Before I used the router DLink Dir 300, and everything was Ok.
View 3 Replies
View Related
Dec 19, 2011
I have Linksys e3200.Can I to setup/use e3200 to watch IPTV?
View 9 Replies
View Related
Feb 24, 2013
Is it possible to establish a connection to an IPTV service with the N150 wireless router?
View 1 Replies
View Related
Sep 22, 2012
I need to set QOS in our new network. We have connected 2 cities together with 700Mbit leased line. On each side we have Catalyst 2960S switches and between them is TRUNK for VLAN 10 and Vlan 20.Vlan 10 is for IPTV (fixed 400 Mb/s for CATV)Vlan 20 is for Internet (rest).Sometimes is happening that Vlan 20 takes more than 400 Mb/s for a few seconds and in this situation we have problems with CATV.Is there any way to make a guaranteed bandwidth 410 Mb/s for CAT - VLAN 10 on this swithces?
View 2 Replies
View Related
Nov 26, 2011
we have Catalysts 2960S for switching in our Wireless high capacity backbone network. As agregation switch we are using 3560x.
I just need to know, if are these 2960S good solution for igmp snooping for whole IPTV stream. It put only a range from backbone and put out on another port. But just specified multicast addresses.
Imput will be 239.128.0.10 to 239.128.0.20 on Gi 0/1,Output wil be 239.128.0.10 - 15 on Gi 0/24
IPTV will be separated on different VLAN for eg VLAN 20,Is needed any priorization configured od switches?,The capacity for IPTV is around 500 mbps
View 4 Replies
View Related
Apr 14, 2013
Region : Romania
Model : TL-WR740N
Hardware Version : V4
Firmware Version :
ISP : AKTA
Network isn't working on pc or on wireless devices. I restarted, reinstalled, rebooted but isn't working. LEDs light up normally but I don't receive internet connection on devices.
View 6 Replies
View Related
Jan 7, 2012
I would like to know if the Linksys X2000 ADSL2+ modem router will work with my IPTV service.
View 3 Replies
View Related
