Transfer IPTV Signal To All Sites Along The Ring?

Apr 26, 2011

My topology is a physical ring, and I need transfer IPTV signal to all site along the ring.For example:

A (headend)--- B --- C --- D
|______________________|
Note: -----: have spoke-mesh defination
_____: no spoke-mesh defination to prevent loop

So, with MPLS/VPLS I can implement it. With spoke and mesh defination, the traffic can transfer form A to B, C or D as drop-continute action in ring topology (between different VC). Everything is good, FRR can work very fast. But when the topology have a failure link, for example the link between B and C, at that time the traffic will go from A to B then B come back to A and A --- D ---C. This action is so stupid, because it can increase delay, jiiter in network. On the other hand, when the node failure ( B failure), C will loss the IPTV signal, even the link from A--D--C always good.

View 6 Replies


ADVERTISEMENT

Transfer Internet Signal 1/2 Mile Via Phone Line?

Sep 5, 2011

I am currently in a situation where I want to share internet between a couple buildings at the site I work at. The problem is that it is a forested area and the buildings are about 1/2 mile away from the source of the internet. The only physical connection of the buildings is the phone lines running between them. Is there any way to use the existing phone line to transfer the internet connection to the other buildings and split it between 2 computers. I know that it would probably involve a substantial loss of speed, but I'm ok with that as the internet at the other buildings will not have heavy use.

View 1 Replies View Related

Can Transfer Files To External Hard Drive And Stream Data Over 5 Hz Signal

Jul 8, 2012

I am going back to college and I will need a router. Both my roommate and I were on the same router went over our bandwidth usage a number of times last year. I've done a bit of research and have come up with a few options: Asus rt-n56u, netgear wndr 4500, and the apple airport extreme. Both my desktop and laptop pc so I'm not sure if that effects the outcome. I am going to need a usb port for an ext hdd, which all of them have. All of the routers have a 5hz signal for better streaming. Would I be able to use the apple airport? It seems the have the best reviews. But I question the compatibility and some of the reviews due to possible fanboyism. Also, If I connect my desktop to the router via a crossover cable and have an ext hdd hooked into the router can I transfer files to the ext hdd and stream that data over a 5 hz signal?

View 2 Replies View Related

Protocols / Routing :: Unable To Access Any Sites Except Google Sites

Jul 8, 2012

MY ISP installed one router in my lab.for internet connectivity they mail me steps :connect your Laptop directly to gi0/3 port to check internet connectivity with public ip 1.1.1.x and Gateway 1.1.1.1 with subnet mask 255.255.255.240 after connection I surprised because I am able to access only google sites like gmail,google search etc. but I am able to ping/traceroute all sites.from browser I am able to access only google sites only.In Router no firewall no such access list.

View 2 Replies View Related

What Is The By-pass Mechanism Used In Ring Topology

Feb 2, 2012

the by-pass mechanism used to isolate the fault if any link fail.

View 3 Replies View Related

Cisco WAN :: 3560X With IP Base In The Ring

Dec 27, 2010

I'm planning to use 2 3560X (access switch) on two different locations connected over two 2921 routers in small ring. 3560Xs are directly connected via fiber. Each 3560X is conected to its own 2921, and 2921s are connected together with GRE over IPSec. So they are creating ring.I'm planning to use small area 0 in this scenario. There are less then 200 routes in the network. Will 12.2(55) IP Base on 3560X support this scenario or I will need IP Services image? "OSPF for routed access" is still little vague to me, there are only tipical case study scenarios.

View 22 Replies View Related

Why Dual Ring Network Is Counter Rotating

Jan 31, 2013

In the Dual ring network using the token passing method, we have the primary ring and the secondary one where in the normal situation only the primary ring is carrying the token in one direction and when this ring is down the secondary will start into operation and takes the token and rotate in the inverse direction of the primary to reach its destination. Why the secondary ring doesn't continue in the same direction to the destination?

View 10 Replies View Related

Cisco :: CUCM Feature Ring Like CUCME

May 28, 2012

I've looked in many places but cannot see how or if it is possible to configure a phone, in CUCM to have a feature ring instead of the normal ring.In CUCME you go into the ephone x configuration mode, and assign the DN to the phone with the button xfx command. What this gives you is a slightly different ring tone when a call comes through. If I am not mistaken it is the same ringtone they use on the show "24".Is there a way to do this "feature" with CUCM?

View 1 Replies View Related

Token Ring To Ethernet Network Converter?

Aug 27, 2012

I'm in a dorm room with an outdated token ring connection that includes phone line ports and cable for my television. In other rooms people are using this to convert their laptop/router to an ethernet portIt converts old token ring ports to ethernet.

View 1 Replies View Related

Cisco WAN :: 2912 Token Ring Support On ISR G2

Dec 5, 2011

My customer wants to replace some Cisco 2912 by new routers, but I can't find a way to add Token ring Network Module on  2951 or 3925 routers with the Cisco configuration tool.Does token ring is still supported on ISR G2 routers?

View 5 Replies View Related

Cisco :: VoIP Phones Customization - Ring / Backgrounds

Mar 12, 2012

has anyone here played around with uploading compatible audio files for custom rings and MOH and/or personalized backgrounds for the phones? I was only taught the basics in our CUCM v6.0.1 and am looking to figure out how to get some good music on my phone as well as play around with other "cosmetic" features. The phone I'm testing with is a 7971(color).

View 4 Replies View Related

Cisco :: RSTP Configuration - 14 Switches Interconnected In Ring?

Apr 2, 2013

I need to setup a layer 2 network consisting of 14 switches interconnected in a ring. Obviously, the design of 14 switches in a ring network is dumb, not here to debate that. Unfortunately, it HAS to be a ring. I've been researching the best way to configure RSTP for this. From everything I've read all I really need to do is configure Primary/Secondary root bridge in the center, and change the Maximum Age field to at least 16 seconds? From what I've read you want a minimum of 3 second buffer + 1 second for each hop due to message age being added by each switch hop?

View 8 Replies View Related

Cisco Switches :: Configuring ESW-520-48P For VoIP / Ring Central

Apr 26, 2011

I am looking for a Best Practices or a few places to pay attention to in the Cisco ESW-520-48P switch I have. My VoIP solution is RingCentral, and while they are Cisco phones, I've been hestitant to setup VLANs etc. the way I am used to. Plus setting up Auto QoS seems different than what I am used to with a 3750 switch.
 
Right now I've left the Smartports Wizard alone, and none of the ports are configured. There are no VLANs or QoS on the LAN currently.
 
What I was running into were calls cutting out where one side wouldn't hear the other anymore, but the call would remain connected. However, this has happened in this small 15 person office, when there is only one employee here after hours, talking on the phone. There isn't any heavy network traffic, because I have network monitoring showing me low usage (no streaming music, videos, or anything else).
 
This switch has a Gb connection to a Linksys SR2024 (the server switch), which is also set at Factory Defaults. I mention that because I recently bypassed the ESW-520-48P, and plugged one phone into that switch and the RingCentral phone worked fine for outside calls.
 
Is there something besides QoS that I should look at in the ESW-520 switch that might be causing a checkpoint of some sort, or interrupting VoIP traffic that I need to configure or disable?
 
And are there any Best Practices or scenario guides for this switch? I found the Admin Guide, but it really just explains every option in the GUI for the switch. And it seems all of my CCNA training isn't working with going in and quickly troubleshooting this switch besides knowing that something in it could be hanging it up.

View 6 Replies View Related

Cisco Switches :: Connectivity With SGE2000 In Ring Topology?

Oct 10, 2012

I´ve got a strange problem with the connectivity within a ring topology.There are five switches from the SGE2000 series and one SG200-50.The SG200-50 is the root bridge and RSTP is configured.From the root bridge switch (Switch 5) I can ping Switch 0.But I cannot ping Switch 0 from PC0.

On the other hand I am able to ping all other Switches (1-5) from PC0.In addition to that I can establish a RDP connection from PC0 to Server0.This tells me that there is no general problem with the connection from PC0 to the Switch0.
 
Right now when I want to configure Switch0 the only way is to connect to Server0 first.But we have to move Server0 and this is why I want to manage Switch0 from PC0 like any other Switch on that network.

View 4 Replies View Related

D-Link DCS Network Camera :: Focus On 920 By Adjusting Black Ring Around Lens

Aug 30, 2012

Just discovered I can change the focus on a DCS-920 by adjusting the black ring around the lens.  It can be focused from very close, just inches, to infinity.  I don't see this in any of the DLink documentation.

View 2 Replies View Related

Linksys Cable / DSL :: IPTV Service Using WAG54GP2?

Dec 22, 2011

i am signed up for an IPTV service. my service provider set up their own hardware including a reciever and a wireless modem. but their wireless modem has weak signal and i cannot connect to it using my computer in the other room. so i wanted to set up my WAG54GP2 modem to use with IPTV service. but i couldn't. i have followed the instructions described there:
 
[URL] (support page for some other IPTV provider, i guess)
 
so, i have checked the configuration details of the other modem which is provided by the IPTV company and found out that encapsulation mode is selected as "DHCP" instead of "Bridge mode only". But my linksys modem does not have an option named "DHCP". so, does it mean that it is impossible to use IPTV with my WAG54GP2 modem? 

View 2 Replies View Related

D-Link DIR-615 :: IPTV (multicast) Not Working With 4.11 Firmware

Jan 31, 2011

After upgrading firmware from ver 4.00 to 4.11 I can't watch IPTV anymore with VLC. With version 4.00 IPTV works over router (wireless or cable) fine but because of some disconecting trouble I upgraded to ver 4.11. Setup is the same as it was in ver 4.00 including Multicast parameter.

View 5 Replies View Related

Cisco Firewall :: Polycom HDX 7000 - Video Calls Through FWSM Ring But Cannot Answer

Dec 26, 2010

Running FWSM Firewall Version 3.1(4)
 
The problem is that calls originating from the outside of the firewall to the inside will ring but you cannot answer. The internal video conference server is a Polycom HDX 7000. There are ANY/ANY rules to/from this server and the default application inspection policy is set for h323/ras/h225 as follows:
 
[code]...

View 2 Replies View Related

Linksys Wireless Router :: E1200 Does Not Work IPTV?

Mar 17, 2013

Not far ago I purchased Cisco e1200. All my attempts to set up the iptv thru wifi failed. Nevertherless iptv works fine when I insert LAN cable directly into my laptop.  On WRT320N does not work. Firmware is Ver.1.0.03.

View 9 Replies View Related

D-Link DIR-601 :: EW-432BRP Not Working With Dish Network IPTV

Jun 6, 2012

I purchased IPTV set-top box from Dish Network (which in turn uses NeuLion services). The set top box works out of the box with TrendNet TEW-432BRP, however the set top box seems to reboot every time I try to launch a channel.The set top box is connected to LAN port 2/DLink is configured to reserve IP address for the set-top box based on its MAC address. The set top is also within its own DMZ so that it does not interfere with firewall settings.

View 1 Replies View Related

Linksys Wireless Router :: WRT320N Does Not Work IPTV

Oct 25, 2011

Today has bought a router. Before it at me was D-link Dir 320. IPTV on DIR 320 worked perfectly. On WRT320N does not work. Firmware has updated to Ver.1.0.04 build 1. Prompt that it is necessary to make?

View 5 Replies View Related

Cisco Switching/Routing :: IE2000 Industrial Ethernet Device Level Ring Support

May 3, 2012

Have a potential customer that is looking at the IE2000 series switch and at the Rockwell Allen Bradley switch
 
Question is does it support Device Level Ring (DLR) capability.  I do not see this specifically mentioned in the Data Sheets but it talks about a
Resilient Ethernet Protocol (REP) and I am wondering if this is the same thing?

View 1 Replies View Related

Linksys Wireless Router :: WRT160N V2 Goes Dead When There Is IPTV Traffic

Aug 20, 2011

I've got an IPTV network with Bell FibeTV with Motorola VIP1216 (the DVR master) and VIP1200 (slave) cable boxes.  All the coax cables in my walls form a wired ethernet network instead of a cable TV network.  To get better wireless coverage in my home, I've set up routers as wireless access points at each of the cable boxes.  Essentially I've plugged the router into the ethernet bridge of the cable boxes, and disabled DHCP and gave it a static IP and did all things I needed to do to disable all the routing capabilities and make it into a switch (here's what I did, step by step: [url...]).  So when I go from one room to another, I just select a new wireless access point to get maximum signal strength and speed.

View 6 Replies View Related

D-Link DIR-655 :: Multicast (IPTV) Forwarding Broken In 1.21EU And 1.31EU

May 15, 2010

Upgrading the firmware from 1.11EU to 1.21EU and 1.31EU has introduced a problem with multicast (IPTV) streams. I have enabled multicast streams and it seems the router no longer forwards a specific address range, in my case 239.139.128.* on port 1234.

I have checked: Streaming from 233.81.233.* works in 1.11EU, 1.21EU and 1.31EUStreaming from 24.1.3.* works in 1.11EU, 1.21EU and 1.31EUStreaming from 239.139.128.* works only in 1.11EUUsing IGMP proxy on Linux I have checked the stream at 239.139.128.* are available as to be sure the DIR-655 is not forwarding them. I see a lot of forum messages stating IPTV streaming is broken since firmware 1.11. It is however working for me in 1.31EU but only for certain address ranges. Can anything be configured to allow 239.139.128.* to work? Because my TV provider uses the 239.139.128.* range for half the IPTV channels I need to get this working.

Related to this, is there page listing known bugs for the DIR-655 and roadmap for future firmware releases?

View 2 Replies View Related

Linksys Wireless Router :: E1200 V1. IPTV (multicast) Is Not Working

Nov 28, 2012

I have e1200 v1 with last firmware 1.0.03. Device using as AP/switch (no WAN port installed). When I open the TV chanal (239.0.1.3) the pictures 1 sec good and then stoped, device not responding. When TV off, 3 sec later internet works and device up.

View 4 Replies View Related

Linksys Wireless Router :: E3000 IPTV Multicast Stream Not Possible

Feb 23, 2011

I've bought a E3000 as replacement for my Linksys WRT350N router.Just upgraded the firmware to version Ver.1.0. 04 (build 6).I use aonTV - an austria IPTV service (Multicast via UDP) - an this worked with my old WRT350N (hw version 1) consistantly well. I hardly had to reboot the router to get the multicast stream.With E3000 I checked the option that it should not filter any multicast traffic - when I reboot the router it works for some time - but after some hours it does not work anymore? I want to watch TV via my HTPC connected via GigaBit Power to the E3000.

View 3 Replies View Related

Linksys Wireless Router :: E4200 Not Possible To View IPTV On Computer

Mar 18, 2012

I have bought Linksys E 4200. I'm connected up by protocol PPPoE by my provider, but IPTV doesn't work on my computer.I use the program IP-TV Player and/or VLC Player and both don't work. I only see the list of channel, but any channel doesn't load. Before I used the router DLink Dir 300, and everything was Ok. 

View 3 Replies View Related

Linksys Wireless Router :: Can Setup / Use E3200 To Watch IPTV

Dec 19, 2011

I have Linksys e3200.Can I to setup/use e3200  to watch IPTV?

View 9 Replies View Related

Belkin Routers :: N150 - Establish Connection To IPTV Service?

Feb 24, 2013

Is it possible to establish a connection to an IPTV service with the N150 wireless router?

View 1 Replies View Related

Cisco Switching/Routing :: 2960S - IPTV VLAN In Trunk QOS

Sep 22, 2012

I need to set QOS in our new network. We have connected 2 cities together with 700Mbit leased line. On each side we have Catalyst 2960S switches and between them is TRUNK for VLAN 10 and Vlan 20.Vlan 10 is for IPTV (fixed 400 Mb/s for CATV)Vlan 20 is for Internet (rest).Sometimes is happening that Vlan 20 takes more than 400 Mb/s for a few seconds and in this situation we have problems with CATV.Is there any way to make a guaranteed bandwidth 410 Mb/s for CAT - VLAN 10  on this swithces?

View 2 Replies View Related

Cisco Switching/Routing :: Catalyst 2960S For IPTV Backbone

Nov 26, 2011

we have Catalysts 2960S for switching in our Wireless high capacity backbone network. As agregation switch we are using 3560x.
 
I just need to know, if are these 2960S good solution for igmp snooping for whole IPTV stream. It put only a range from backbone and put out on another port. But just specified multicast addresses.
 
Imput will be 239.128.0.10 to 239.128.0.20 on Gi 0/1,Output wil be 239.128.0.10 - 15 on Gi 0/24
 
IPTV will be separated on different VLAN for eg VLAN 20,Is needed any priorization configured od switches?,The capacity for IPTV is around 500 mbps

View 4 Replies View Related

Cisco Routers :: Linksys X2000 ADSL2+ Modem Router And IPTV

Jan 7, 2012

I would like to know if the Linksys X2000 ADSL2+ modem router will work with my IPTV service.

View 3 Replies View Related

Cisco Switching/Routing :: Cat6500 / IPTV Multicast Network Devices High CPU Utilization?

Jan 30, 2013

i have a campus network with 2 core Cat6500 and multiple 4500 series distribution switches plus 2960 series access switches,we have deployed IPTV system in the network but currently 50 TVs are working through sattelite stream from streaming server Cisco's DCM 9900.we are planning to add more  300 TVs in the network and i am wondering that when all of them will be deployed then what will happen for switches cpu utilizations when all the Tvs will be running on the same time with different different channels.

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved