Cisco Switching/Routing :: 3750G Setup - Multicast Traffic Across Link
Jan 12, 2012
I am having trouble getting some multicast traffic across a link. I have a 3750G setup, with IP routing and IP multicast routing, between two laptops. This will eventually sit between two networks that cannot be physically connected to each other for security reasons. I have static joins on the ports but cannot see the multicast traffic on the receiver. I am attaching the latest config. The sender(10.10.4.2) sits on gi1/0/24 and the receiver(10.10.3.2) sits on gi1/0/1. I am using VLC to test this and it will connect if I point the receiver to the address of the sender, but will not receive any multicast. The multicast traffic is not making it to the 10.10.3 side, I used wire shark to verify that it was not making it across.
View 3 Replies
ADVERTISEMENT
Feb 13, 2013
I manage a network with a ghost server, a 3750G, several outside access, and some vlans.This is a very simplify view of this network:
The ghost server is on all vlans connected to a trunk port on the 3750G which is used as a central switch and for basic routing.All equipements connected to vlans 1, 2 or 3 are on 2950 switchs themselves connected to the 3750G on dedicated access ports, each in there respective vlans.
All equipements connected to vlans 1, 2 or 3 have as gateway a vlan interface on the 3750. (10.0.x.3)All the vlan interfaces have route-maps applied on them to redirect traffic to their dedicated outside access.The route-maps match only traffic destinated to the outside.
Everthing is working well but the multicast.When I create a ghost session on the server, I can see computer connecting on it, but the multicast never start.If I use directed broadcast it works with good perfs, but the CPU processes of the 3750 go high because of the IP Input (Till 99%).If I remove the route map from the vlan interface which is on the ghosted network, the multicast works but with poor perfs.If I shutdown the vlan interface the multicast works well with good perfs.
It seems my problems are tied with the Vlan interfaces but I don't know why.
This is a sample of the config:
switch 1 provision ws-c3750g-24ts-1u
system mtu routing 1500
vtp domain SM
vtp mode transparent
ip routing
[code]....
View 5 Replies
View Related
Nov 3, 2011
I have a 2x Cisco 3750G switches (Stacked) that are part of an IP Video Surveillance System .All network is set to 1 VLAN (VLAN 1 default).The Cisco SWs ( Core ) are configured with IGMP Querier + Snooping .Connected to the Cisco SWs are 4 Fiber Rings(Loops) for redundancy . RSTP and IGMP Snooping are enabled on all the network SWs .Network Architecture Figure :
When all Fiber Rings (Loops ) are connected , the Cisco and Ring SWs spanning-tree tables show the blocked and forwarding ports properly .I am able to connect all my IP Cams + Encoders to the Ring SWs and connect my Servers + WorkStations to the Cisco SWs to record and view the multicast ip streams .All streams from Rings 1 ,3 and 4 are getting normally to the Servers + WorkStations through multicast ( IGMP Snooping are filled correctly on the Cisco and non-Cisco SWs ) . All multicast streams are joined normally except for Ring 2 .The Multicast streams passing through Ring 2 will operate normally for around 2 hours then after that the Fiber SWs begin to flood their multicast traffic causing the cams on the same switch to drop off the network .
I checked the Configuration of all the SWs on Ring 2 but all are are the same .
What is weird is that I have to set all the streams to unicast to stop the flooding just on Ring 2 (All other rings are not affected ) then after some time if I enabled a video multicast stream on one of the SWs of the Ring it will be streamed properly to the Servers + WorkStations ( All IGMP tables along the way will be filled properly ) then again after 2 hours or so , the flooding will start again suddenly and all IGMP table entries for the SW on Ring2 will be empty . No problem occurs on the other Rings which have more multicast streams .
View 0 Replies
View Related
Feb 15, 2013
we have 3750G stack connecting to H3C switch cluster connecting through two trunk portchannels.and we have MSTP configured since H3C support only MST.MST is configured as below.instance 1 1,168,178,198instance 2 148,158,188,instance 1 LANS are extended to H3C,instance 2 VLANS are local to 3750 stack.,As a new requirement we need to add a another VLAN to this topology.and we are planing to add this VALN to instance 1,can there be any traffic interruptions.
View 2 Replies
View Related
Feb 18, 2013
I have a 3560X switch with interfaces 36-48 on the same LAN. All interfaces are switchports. Hosts on 38, 39 and 40 are multicast senders: all sending to the same single multicast address. Hosts on 36 and 37 are receivers, having joined that multicast group. I created an SVI for the LAN and put it in ip pim passive. (That is the only PIM mode allowed for an SVI with my IOS.) Show ip igmp snooping groups shows that 36 and 37 are the only interfaces in this group. I attach a laptop to interface 42 and Wireshark, and the laptop is receiving the multicast traffic. The laptop does not join the group. I expect it would not see the traffic.
View 4 Replies
View Related
Jan 16, 2012
does 6500 with SUP-720 support nat on multicast traffic?
i know it support Multicast service reflection based on SXI4 which can facilitate me on destination address nat.
but if i need only source nat, does the defualt NAT feature supported on multicast traffic ?
View 1 Replies
View Related
Dec 20, 2012
I am trying to resolve a situation where we need to send multiple (2 atleast) multicast feeds from a source to our multilayer switch (3560x).
The problem with the source is that it can only send a feed to a single switch at a given time. It can not send 2 (identical) feeds to two 3560x devices (on 2 different subnets/vlans). I was wondering if i could make the two 3560x devices appear as 1 device (using virtual chassis system or a similar feature). I am running ip services IOS feature set (c3560e-universalk9-mz.122-58.SE2.bin).
View 1 Replies
View Related
Dec 6, 2012
Attached setup i am planning for testing multicast output from different vendors using VLC and STB. This Setup made to test the picture quality between the vendors at the same time on the multi viewer screen.
1) Only a 2960 Gig port switch with only one L2 v lan with IGMP snooping enabled.
In this scenario where Source and receivers are in the same L2 v lan ( no L3 interface is involved) hope i would able to test all the multicast sources with out any additional configuration on the Cisco switch.
View 6 Replies
View Related
May 7, 2012
I have configured multicast(ip pim dense-mode) on two 2911 that are connected by a Multilink( 3 Mbps) Wan connection.The configuration works fine for awhile and sometimes all day but at some point one of the Multilink interfaces stops passing multicast traffic.I perform a SH Multilink 1 on the interfaces and one show multicast packets incrementing and one does not, it just stops.The problem acts like there is a buffer that gets full and after that happens it just stops working.
View 2 Replies
View Related
May 12, 2013
I've been handed a requirement to try and get a multicast server working on my setup. Trouble is, I don't know if I can with the feature set I have on my switches. What is desired is that a multicast server (stand alone, but network connected, obviously) be accessible by everyone on the local network (multiple V LAN's, multiple SVI's) in the building.
All users will be connected to the one switch stack, although some will want to be wireless (which is one of the separate V LAN's) - I don't care if the wireless requirement goes by the wayside - they can sod off. :-) The main purpose will be multicast, high quality video.
I have a single switch stack consisting of two (soon to be 3) WS-C3750X-48P switches running the IP BASE feature set.
Question - can I do this on IP BASE, or do I need to upgrade to IP SERVICES?
If I can do it on IP BASE, does anyone have any links/pointers to setup this properly? Currently installed IOS is 12.2(58)SE2.
View 3 Replies
View Related
Aug 8, 2012
Multicasting. The configuration is I have a 6506 as my core switch receiving multicasts from an interface assigned to VLAN10. I have a monitor port setup with a PC running Observer which says multicasts are being received on the core switch. On a different interface on the core switch I have a 2960G switch connected to it and this interface is on VLAN 10. The 2960G switch has a workstation connected to it that needs to receive the multicasts. How do I configure the 6506 and/or the 2960G to process the multicast traffic?
View 0 Replies
View Related
Nov 30, 2009
I have two Catalyst 6506 in VSS mode with VS-S720-10G running 12.2(33)SXI1 IP SERVICES.I have two firewalls that communicate on to the other through a dedicated VLAN created on Catalyst 6506.
One firewall is able to ping the other one on this dedicated VLAN but if I send multicast traffic from firewall-1 I didn't receive it on firewall-2.I found a bug related to multicast issues on Cisco WS-C6509-E with VS-S720-10G. The bug ID is CSCtc59038.
View 9 Replies
View Related
Jan 15, 2012
Has any come across show ver memory details on 3750G-48PS as below, One of our Catalyst 3750G running software 12.2(44)SE2 shows unexpected DRAM as below:
cisco WS-C3750G-48PS (PowerPC405) processor (revision F0) with 0K/12280K bytes of memory. This would equate to around 11MB memory which does not seem right... Is it a known IOS bug?
View 1 Replies
View Related
Nov 13, 2011
I am trying to setup a network using Cisco 2960 switches with vlans configured. One vlan will handle video coming from four cameras that are connected to another 2960.
We have four cameras feeeding one port each on a 2960, that 2960 in turn feeds one port on the main 2960 which is the video vlan for that site. From the site it goes back to a Cisco 3750 to be sent over to a Sonicwall firewall. If we connect to the 2960 that the camera are connected to we can see the video, but not on the main site 2960.
View 5 Replies
View Related
Mar 26, 2013
We have some ASR WAN routers which have a dedicated 400M interface to a remote site.
Servers on our Local network source the data through some firewalls via 10G interfaces, which connects to 4500X WAN switches then to the Routers on 1G links.
The sources are rate limiting the traffic but the routers are periodically dropping packets which I think is mostly due to burstiness in the traffic between as it traverses through from 10G links to 1G then to 400M.
How to setup traffic shaping on the 4500X outbound port to our WAN routers.I'd like to see if we could buffer and smoothe out the traffic as it exits the 4500X WAN switch 1G port to the WAN Routers.
View 1 Replies
View Related
Jan 14, 2012
i have a strange issue with an HSRP Setup. I have two (S1+S2) 3560 as Core/Distribution Layer. Inter-vlan routing are enabled on both Switches. S1 and S2 are connected with an ether channel over four fibre ports. S3 -S5 are the (L2) access layer.
Gi0/1 on S1 and S2 are L3 ports, connect to a Linux Firewall.
HSRP is enabled, S1 is the active router and the STP root bridge.
But, my monitoring via cacti show me, that the Gi0/1 on S2 is active, too! But it should not be active? Only if S1 fails, should S2 the active switch.A client from the access ports on S3 - 5 gets traffic from the Internet via Gi0/1 from S2. Gi0/1 on S1 is active too, but will send mostly traffic to the Internet. Why is S2 active and why route it traffic from the Internet to the client?
View 15 Replies
View Related
Mar 21, 2012
I got Two Distribution Switches of Cisco 3750G. Each Distribution have two 3750G switches stacked. I also have one Cisco 3750V2 Access Switch connected to both Distribution. When I am checking for redundancy, I can only get redundancy test pass for one link not atall for other. If I have a link up with Distribution 1 only then its fine; but disappointment with Distribution 2 link. I can see that the switch priorities of Dist 2 is not correct ie. Master's priority is 10 and Member's is 15.
My question is that due to misconfigured priorities on Distribution 2 stack switches I am failing with redundancy if ONLY Dist 2 is up and Dist 1 is down.
View 4 Replies
View Related
Apr 22, 2013
I have pair of 5596 switches in vPC. One host say "HOST A" is connected to the primary vPC peer and other "HOST B" on secondary vPC peer.Both are in same VLAN 10. Both hosts are vpc orphan ports as their NIC is configured in active/standby mode.I have configured span session on both vPC peers with span source as VLAN 10 in rx mode.Span destination is connected to secondary vPC peer. The issue here is that I am not able to capture the traffic originating from HOST A destined to HOST B which is traversing vPC peer-link.Same issue occurs for the traffic in reverse way and span destination on primary vPC peer. In a nutshell, any traffic which crosses vPC peer-link is not getting captured.
What could be the issue and is there any solution for it. Below mentioned is the span config and relevant interfaces. [code]
View 4 Replies
View Related
Mar 4, 2012
I've one Cisco 3750G-12S with ip routing enable, the swtich is with IP Service firmware, with PRR support.Currently set my default static route 0.0.0.0 0.0.0.0 10.1.18.71 to my Firewall A Currently all of the VLAN for will be routed to 10.1.18.71
I've created a new VLAN 2 for my 10.1.2.0/24 network with the VLAN interface 2 ip address 10.1.2.10, my intention is to route 10.1.2.0/24 traffic to my 10.1.2.1 by creating the access list and route-map.
I've configure my test pc with a static ip and my gateway pointing to 10.1.2.10 (VLAN 2 gateway) , i'm not able to route to 10.1.2.1.
View 7 Replies
View Related
Feb 19, 2013
I try to pass multicast traffic between two vrf on the same 3750 switch. I have IP services IOS and sdm template routing.
here is my config:
ip routing
!
ip vrf vpn2
rd 1:1
mdt default 232.1.1.1
route-target export 1:1
route-target import 1:1
[code]....
Now I'm stuck - I don't know what to do to pass multicast traffic. Do I have any chance to run this config on 3750 chassis?Perhaps "Configuring Multicast VPN Extranet Support" document will be useful, but it concerns Catalyst 6500? [URL]
View 0 Replies
View Related
Nov 8, 2012
I have a couple of 3750G-24T-E switches running IOS 12.2 I would like to upgrade to IOS 15.x. Is this possible? Where do I find some information on the required licenses and costs? I must admit that the cisco search function did come up with a few pages but i was not able to extract the required information. I have not used the new software activation features yet.
View 1 Replies
View Related
Jun 7, 2012
I've got a requirement to do Inter-VRF routing (need MP-BGP) using a private AS Number on a stack of 7 x 3750G's, my question ultimately is the performance overhead of doing such a change.
The stack will have no more than 300-400 routes even with the duplicates invoked from doing VRF leaking so I can't see much of an issue myself, we already have 2 VRF's and OSPF running in each VRF just don't have MP-BGP to do the VRF leaking.
Ultimately there will be about 4-5 VRF's (I know there's a Software limit of 26 VRF's on a 3750G).
View 3 Replies
View Related
Oct 2, 2012
I am trying to stack the following -
3750G 12S - 12.2.53(SE2 IP Services) Running EIGRP & OSPF
with
3x 3750X 48P-S - 12.2.53(SE2 IP Base License)
Doing some research, the IP Base does EIGRP on the 3750X, does it do OSPF?
If not I will have to get licence for the 3750X?
View 3 Replies
View Related
Oct 8, 2012
I am having a switch 3750G (WS-C3750G-24TS-S) running a software version (c3750-ipservicesk9-mz.122-55.SE6.bin) and using the PBR with IP SLA.While, i am applying it on interface, it says not supported....
route-map TO-CAS-E0 permit 10
match ip address 125
set ip next-hop verify-availability 10.116.199.200 10 track 100 (if i change this command to set ip next-hop 10.116.199.200, it works)
!
WAN-L3-3750SW01(config-route-map)#interface GigabitEthernet1/0/11
[code].....
View 2 Replies
View Related
Jan 2, 2013
I have one switch 3750G12S I joined the company new, I found that they want to replace it with Alcatel stack switches. I didnt configure this Cisco switch before. how to configure it. I have 4 other new cisco switches in the topology which is not created yet. the 4 switches are all 2960.
View 17 Replies
View Related
Nov 20, 2012
have 2 3750's one is an 3750E the other one is a G... Since they are 2 different versions Do I need to correct ios for each for example my 3750E switch i would have
IP BASE
c3750e-ipbasek9-mz.122-53.SE2.bin and for my 3750G switch should i use
IP BASE
c3750-ipbasek9-mz.122-53.SE2.bin
Which would be 2 separate images
View 4 Replies
View Related
May 26, 2011
I have a 3750G and bought a new 3750X. It possible to stack these two together?
View 5 Replies
View Related
Nov 18, 2008
I have a 3750g on which I am trying to configure the ip policy route-map command on each of the vlan interfaces. However after entering the command it does not appear. I'm not sure what to do at this point. I have changed the SDM template to routing and I am running the IPServices image.
View 2 Replies
View Related
Jan 23, 2013
I have just received a new Cisco 3750G Switch from my parent company. When attempting to install the switch, I discovered that it will not boot to CLI, only to the bootloader. After using the command boot, the switch attempts to boot the most current IOS version, but fails, stating "error loading XXXXXXXXXX.bin".
Obviously, I just need to get a functional version of the IOS onto the switch to boot, but the problem is exactly how can I do that? All (or most) the commands with which I am familiar are unavailable in the bootloader, so all methods known to me fail. Is there a simple way (maybe using the copy command?) to put the .tar or .bin file onto the flash?
View 2 Replies
View Related
Sep 17, 2012
I am trying to create an ACL that walls off a VLAN and only allows it to the internet. This is on a 3750G, currently the 3750G I am attempting this on is in a stack. I have another 3750G that is a standalone.
The first way I attempted this was to create two access-lists: access-list 101 permit tcp 10.249.1.0 0.0.0.255 any eq 80 access-list 102 permit tcp any 10.249.1.0 0.0.0.255 established
Let's call the 10.249.1.0 VLAN 2. I applied this to the VLAN2 interface, 101 out, 102 in. It didn't work. If I place a deny statement with nothing else, that works.
The second attempt was this: access-list 101 deny ip 10.249.1.0 0.0.0.255 any access-list 101 permit ip any any
I applied this to a VLAN I wanted to block VLAN2's traffic from reaching, let's call that one VLAN 3.
This lets all traffic from any VLAN (including the one I'm trying to block). If I remove the "permit ip any any", then all VLANs are denied. Which I understand is correct due to the implied deny all. What I don't understand is why it isn't applying the ACL to the specific VLAN.
View 3 Replies
View Related
Jun 2, 2013
I have a 3750G that used to be a Stack Master of a stack comprised of 2 identical switches. Since then, we have removed the stack from production, and I factory defaulted the stack MEMBER and that went fine. I just held the "Mode" button on the front until the lights all lit up and then issued the reload command and the switch came back with no configuration OTHER than the vlan database I issued the "del vlan.dat" command to no avail. I just manually removed all the vlans.
The stack MASTER on the other hand will NOT go back to factory defaults, and will also NOT erase the vlan database. Everything I try will NOT work. I've tried the following
1) Hold mode button & issue a reload after the lights start flashing
2) issue "Write Erase" then issue "reload"
3) issue "Write Erase", then issue "Write", then issue "reload"
4) issue "erase start" then issue "reload" (just in case the "write erase" command is being depriciated or something weird)
5) issue "erase start" then issue "copy run start" then issue "reload"
Is there a special way to reset a StackMaster back to factory defaults?
View 6 Replies
View Related
Apr 22, 2013
I have one 3750X with C3KX-NM-10GT, I need to interconnect using stackwise to 3750G-24TS. The 3750X needs IOS 15.0(1) to use C3KX-NM-10GT, and the latest IOS for 3750G-24TS is 12.2.55. How can I interconnect them using diferent IOS?
View 2 Replies
View Related
Jan 29, 2013
I have a 3750G switch that can't detect another switch or be detected through its stack ports. I tried the recommended test; looping a cable between the ports and rebooting. I get the following message as the switch boots: SM: Detected stack cables at PORT1 PORT2. However, if I connnect another switch, it won't detect it and can't form a stack.
View 4 Replies
View Related
