I know about recomendation to update a system software! Here is my software version and rdp plug-in version: asa843-k8.bin, rdp-plugin.120424.I also tried to use previous version of rdp plug-ins, but connection through RDP still not work normally! 90 percent of the attempts to give a black screen.
View 1 RepliesPerhaps once a week my ethernet port stops working. That is, it is still displayed as 'working properly' in the device management screen, but it is unable to connect to dns. System restore does not solve this problem. plugging the ethernet cable in and out (10 times) does not solve this problem. Modem reset does not solve this problem either. I decided that perhaps ethernet controller is faulty, or perhaps the ethernet port in itself- so I bought a 'usb to ethernet' adaptor and surprisingly the internet connection problem persisted (during the instances when my laptop ethernet port had problems connecting to DNS, the adaptor was also unable to connect to internet).
What does solve this problem is this: I have another notebook - I plug the ethernet cable into that computer. Obviously, internet works without any problems with my second notebook. After that, I plug the ethernet cable back into the laptop which is now unable to connect to DNS. Quite often the Not being able to connect to DNS issue still remains the first time I do this, so I have to connect ethernet cable back into my second notebook and then plug it back into the notebook with a connectivity problem. After I do this 2 or 3 times, my windows 7 laptop is finally able to connect to internet.
My laptop won't connect to the internet at all and status shows limited access to router. It was fine a few days ago until a Windows update. I did a system restore on it back to before the windows update and the internet was working just fine but then there was an automatic windows update again and the connection is gone again. When I try to troubleshoot it says the network adapter is not working properly. I'm currently using the main computer in the house. I can't access any network at all on my laptop and I'm nearly in tears. This has happened before about 7 months ago after a windows update. At that time I did a system restore and reinstalled the updates and it worked just fine. This time nothing. I have tried to check for updated drivers for the network adapters but windows says I'm running the recent ones.
View 8 Replies View RelatedMy wife's computer was working fine. Two nights ago, a Windows update was automatically installed. Now, it will not connect to the internet. The map shows it connected to the network. We have several other devices on our network both wired and wireless and all of them are working fine.
I was able to use system restore yesterday to roll back the update. It still did not work. However, I tried connecting to a neighbor's wireless. It said something about refreshing the adapter and then it connected to our network and was working fine. Unfortunately, when she shut down last night, the windows update was reapplied. I turned off automatic updates and tried using system restore. It did not work this time. I removed every update that was applied in the last 48 hours but I still cannot get the computer to connect to the internet. However, it does connect to the internet when I bring it up in Safe Mode.
I am configuring it with our ASA 5540 default 2 SSL License. I have got 10 demo license from Cisco, however I am yet to activate it.
I have problems is accessing SSH and Web Services.
1) SSH: When I try to ssh one of my device, it ask me to give me Username and Password. After that it it shows the full black screen and do not ask me to provide Enable password. But Telnet is working fine.
2) WebService: We have one web service (internal). 2 webserver connected to cisco css 11501. the URL is http://10.10.10.10/web. I try to access it from the WebService page with giving 10.10.10.10/web and 10.10.10.10 using http protocol. but it shows that the server is not reachable.
Model: ASA 5520
ASA: asa843-k8.bin
We are having an issue with the the ASA RDP2 plugin, it has been working correctly since the installation of the ASA 2 years ago.1 month ago the functionality stopped working in IE activeX. I performed an upgrade of the ASA software in an attempt to fix, unfortunately this has not resolved the issue. Reimporting the plugin has not solved our issue either.
When using the Java client, there is a warning that -"The terminal server disconnected before licence negotiation completed. Possible cause: terminal server could not issue a licence"When a user clicks on a bookmark or types in a server name that is associated to the RDP2 plugin, the page timeouts and goes back to the home screen of the clientless SSL vpn.
Whenever I start a Cisco VPN from any machine on the network, DNS requests to the DIR-655 stop working. If I reboot the router, DNS starts working again (the VPN was left on). Why starting the Cisco VPN would freak out the router?
View 3 Replies View RelatedRouter: Linksys Wireless-G Model: WRT54G v8
Wireless Adapter: Belkin model F7D1101 v1
I have two computers in my house, one is set up directly to the modem/router and the other (in my room) is set up wireless using that belkin adapter above.
Everything has always worked perfectly, but two days ago things went haywire. If my PC connects to the wireless, then it makes the router stop working for the other computer and any wireless devices I have. As long as I don't have my PC connected, then things run smoothly and there are no problems, so it's definitely stemming from my PC?
I thought it might have been the router at first, so I switched it out and it worked fine for over 24 hours, but then the problem came back.
Windows IP Configuration
Host Name . . . . . . . . . . . . : Sunako-PC
Primary Dns Suffix . . . . . . . :
[Code].....
I have installed VM ware v Sphere Enterprise Plus 5.0.0 and created a VM using an OVA file with LMS 4.1 running in Linux. It was working good since 3 weeks ago and I was adding snmp server configuration in all my devices (routers/switches) and suddenly one day DCR Server process stop working. I was trying the following actions:
1.- dmgtd stop -> to stop daemons
2.- dmgtd start -> to start again the daemons
And the DCR Server does n´t start up automatic.
Then I try this:
1.- pdexe DCR Server
And show this message:
[CPLMSCOL01/root-ade ~]# pd exec DCR Server
ERROR:Get reply from server failed:
and don´t start up the DCR Server.
I have setup a Cisco SR520W and everything appears to be working. After a few hours, it looks like the WAN port stops forwarding traffic to the Internet gateway IP of the device.
If I unplug and then plug in the network cable connecting the WAN port of the SR520W to my the modem, traffic startings flowing again. Also, if I restart the SR520W, the traffic will flow again.
Here is my config file:
Building configuration...
Current configuration : 17830 bytes!version 12.4no service padservice tcp-keepalives-inservice tcp-keepalives-outservice timestamps debug datetime msecservice
[Code].....
i've one of my 3500 that when finish to download the os, the front led stop working. During the power on and all the test the led is flashing in various colors pretty ipnotizing :-) When it bacame operative, the led stops. If i issue the test led flashing console command it works.
View 1 Replies View RelatedYesterday my wireless internet just appeared to stop working completely, it has always worked fine up unti now!I have checked all the usual issues, it is nothing to do with my router as i can use other laptops/desktops to access the internet fine.I am using a Pavillion DV6-1215sa which has a Atheros AR9285 802.11b/g WiFi Adapter.It has full strenght but just says Limited Connectivity, so it is picking up the wireless network but wont actually let me connect to the internet via it.
I am able to access the internet when i hard wire the ethernet cable into my laptop, but the just wont work for wireless.I have tried lots of different suggestions so far, but still cannot access the internet.
all of a sudden my internet stop working and its now saying limited access ive tried all of thoose ipconfig things and none of them worked
View 19 Replies View RelatedI'm trying to get a static IP because I'm hosting a team fortress 2 server.So on windows, I made my internal IP static and that worked.On my router(cisco EPC 3925) you can go to administration ,then management and it says connection mode: DHCP which you can change to Static IP. When you change it to static IP it askes you:[CODE]
View 5 Replies View RelatedOnce again I'm stuck to tethering on my phone due to my router deciding to call it quits for the random moment. I cannot access its control panel, the network just goes kaput. Given that I don't have access to the router since it's part of a double house (the side I'm not on of course), this is getting beyond irritating to reboot it when this happens as that is the only way to fix it. The connections are even wired, too. What kind of money does it take to get a router that is going to STAY on and just work? I'm ready to dump some serious cash into this at this point because this happens at least twice a week anymore. I just want a router that works. It needs to be wireless as my neighbor does use his kindle on it every once and a while.
View 4 Replies View RelatedMy new Windows 8 computer is not wi-fi capable, I bought the adapter but it only works with Windows 7, they have a link to upgrade to Windows 8 but I don't know where to go from there.
[URL]
I'll be downloading off of newsgroups and be pulling 3-4 MB/sec, no problems. My downloads are charted so I can see my speed never drops at all.but my web browsing will just STOP, for ~30 seconds. I'll have multiple tabs just STOP and crap out, while my downloads run fine. This also happens when I'm not downloading, so I know it's not a bandwidth issue,i assumed it was a router issue until I replaced my router and am getting the same issue.
View 1 Replies View RelatedI've dell inspiron n5110 with dell wireless 1702 802.11b/g/n sometimes working sometimes not working and work if i restart the machine .
while i'm working on laptop the net does work and once i try to find the wifi ssid i can't see any of them and written no network available.
i do lot's of thing and the problem still
1. update the drive
2.change the properties of wirelss adapter in power managment
I recently built a new computer and it runs a wired connection. I was having problems with dns dropping.until i set static ip and dns. But now whenever my computer is on my router doesn't broadcast a wireless signal and none of my devices can connect to wireless until I turn off my computer. The router is a linksys wrt54g2
View 4 Replies View RelatedRegion : Others
Model : TL-WR741ND
Hardware Version : Not Clear
Firmware Version :
ISP :
after year and a half of using TL-WR741 ND router, it suddenly stop working during the night. I have no problems with router before this happened (I think only one or two reset in 1 year and 6 months). System led light does not flash (some sytem error) and I can't access to 192.168.1.1 router setup site. I tried almost everything, unplug power, reset etc. for almost 100 times, reconnect the router with modem and PC in all posible ways, but still can't establish connection or even access to router's setup. Obviusly internet works fine?
I am using a dell Vostro 3550 series, window 7 which I recently upgraded it to 64 bit from 32 bit and after that my Intel WiFi utility stop working. I can create the WiFi hot spot and connect my phones and laptops but its not sharing the internet. I've checked the "share my internet" button too but still then its the same result.
View 22 Replies View RelatedI have an odd problem where http downloads will stop after a few seconds. I can stream video, do anything else with the internet perfectly. It's just when downloading files from websites will this happen.I use a wired connection. I have tried Firefox, Chrome, and IE10, and this problem happens in all of them. I use a WRT54GS router. I have tried downloading files in Ubuntu 12.10, Windows 7 using wireless, and WinXP, and they all can download files perfectly. Only Windows 8 seems to have this problem. Another thing is that my Windows 8 is a fresh install.I have also tried disabling Windows Firewall to no avail.
View 1 Replies View RelatedAfter an hour on the phone with the Linxys support people I'm feeling like I've been scammed.I have a 2 year old, almost to the day, Linxys Wireless-N Broadband Router, model # WRT160NVZ, which decided to stop working today. I contacted Linxys support and was told since it is 2 years old it's no longer under warranty, ok. If I choose I can pay for a service call and the tech may be able to fix the router, no guarantee. I had another option to purchase a service plan but again no guarantee repairing the router. My third option was to purchase a brand new wireless router for a discounted price, if I chose this option the tech would attempt to repair the router at no charge. I expressed my concern that it would take a few days to receive the new router and what would I do while waiting. I was then assured the router I have now could be repaired and would be able to hold me over until I received the new router.So I chose the 3rd option purchasing a M20 wireless router to be shipped to me within 3 days. After providing my credit card number and billing/shipping address the technician was now able to work with me in trying to repair the current router. He had me access the Linxys website, he instructed me in resetting the router and resetting the settings for it on the website and PRESTO, my 2 year old router now works again.but feel that this is a scam, programmed in the router to occur within 2 years of purchasing where the settings entered no longer work but once changed works perfectly well.
View 6 Replies View RelatedI've lost connectivity with all but one of the ethernet ports on my E4200 router. My desktop PC was connected to Port 1 but stopped working. Network troubleshooting via my Windows 7 Dell 8300 said I was not connected and to check the cable. I did that with several different cables and tried the usual router and modem reset. Only through trial and error did I find that I could connect to port 4 which is why I am able to write this post. What could have changed to disable ports 1-3 and can I get them working again? No issues with wireless connectivity.
View 3 Replies View RelatedI received a Linksys E1200 from a friend who careless tried to upload an incorrect configuration. After that the device became use full. It don't work at all.
View 1 Replies View RelatedFew days ago the wireless in my son's Dell Inspiron 620 went bad. It does connect to my old router (WEP), but speed is terrible and connection goes bad after some time. I can also see my modern router and enter the key successfully (WPA2), but it won't connect. Connection to both routers went well for months before, and still goes well from all other devices in the house.
I read the issue with McAfee that was posted late August and followed the steps. Connection in safe mode didn't work. Then I removed McAfee from the PC, no difference. Then I restored the PC to a couple of days before the issues began, removed McAfee again (as it came back through the restore), no difference.
I reinstalled the drivers of the Dell wireless card, no difference.
I'm having problems connecting to the Internet using the wireless adaptor - it will connect initially but the connection is very very slow and then will eventually drop out and stop working.When I connect using an Ethernet cable, there are no problems whatsoever so I know it is not a service provider issue.I have updated the BIOS to A11 and all drivers are up to date. The wireless adaptor is Intel Centrino Wireless-N 1030. [code]
View 3 Replies View RelatedMy 3rd day with my newly bought All-In-One 2320 i7, 2TB, 8MB...This is the seond issue I found on this machine:Browse iplayer page, choose a video to watch, but...when viewing video from iplayer in IE, browser stop working. The whole page freeze.Same thing happened on youtube.
Things I have tried:
- Test it in Firefox. Same result. So bad.
- Update my flash player, java,..etc.
What else can I do? So dissapointed. I have promissed my son to show him the cbb animation cartoon on my new computer (big screen)..
i have a server with windows server 2003 that SQL server 2008 is installed on it.regulary server service will be stoped automativcaly and all shared folders will be unshared and i must restart server and waiting for next stop and .
View 1 Replies View RelatedI just upgraded the firmware on the RV220W to 1.0.2.4 and it looks like the time is not updating. I tried a couple of different default time servers and also a custom time server (time4.nrc.ca).
View 2 Replies View RelatedI am using an 831 router and am trying to get DDNS to work. Here is the debug output:
RESS_ASSIGN: Interface Ethernet1 assigned DHCP address 67.162.204.242, mask 255.255.254.0, hostname testlab831.xxxxxx.com
00:53:06: DYNDNSUPD: Adding DNS mapping for testlab831.xxxxxxxx.com <=> 67.162.204.242
00:53:06: DYNDNSUPD: Sleeping for 3 seconds waiting for interface Ethernet1 configuration to settle
00:53:09: HTTPDNS: Update add called for testlab831.xxxxxxxx.com <=> 67.162.204.242
00:53:09: HTTPDNS: Update called for testlab831.xxxxxxxx.com <=> 67.162.204.242
[code]....
what the problem is with the "Call returned Connection time out for update testlab831.xxxxxx.com <=>" line.
I discovered that my LAN port was not found anywhere, even though it was enabled in BIOS. This prompted me to buy a netgear USB wireless adapter which gives me internet access but I'm having several issues now.I am unable to synch my internet time with any server, and therefore cannot use windows update which requires time to be synched for whatever reason.
View 3 Replies View RelatedI'm having trouble seeing my WD 2TB HDD USB after the latest update, it's not showing the partitions anymore. Before the update it was working perfectly.
I'm using 1 partition for my Mac backup and the other partition for Win filesharing.