Cisco VPN :: ASA 5520 - List Of IP Addresses That VPNed Into Network
Apr 21, 2011
My boss would like to know if there is a way to find out the ip address of a person VPN ing into our network. Let's say Joe Smith is VPNed in from home and his carrier is cox communications. How would I go about finding out what his ip address (the ip issued to him by cox) is? Is that even possible? If it is possible, is there a way to create a list of ip addresses of everyone that has ever VPN ed into our network? We are using a Cisco ASA 5520 and Cisco VPN Client.
View 7 Replies
ADVERTISEMENT
Feb 26, 2013
So in the past from 8.2 down I had one to one NATs like so
static (inside,outside) A.A.A.A B.B.B.B netmask 255.255.255.255
but for 9.1 im running now I need to do this
object network obj-B.B.B.B
host B.B.B.B
nat (inside,outside) static A.A.A.A
So if I make an ACL to permit outside public access to the public IP (A.A.A.A) in 9.1 do I use real B.B.B.B ip address or the object itself obj-B.B.B.B?
View 4 Replies
View Related
Apr 26, 2012
I need to know the maximum number of MAC addresses that can be entered in to the MAC security filter list on the AP541N.I know it has a maximum number of 200 concurrent users, however the documentation does not specifiy whether this also applies to the MAC filter.
I have used wireless acces points in the past that allow hundreds of users but only allow 64 MAC addresses, so this is very important.
View 1 Replies
View Related
Mar 12, 2013
Find list of all the MAC address of the devices connected to the router?
View 2 Replies
View Related
Feb 23, 2013
I have a Wireless N router model F5D8236-4 v2 (01) with firmware 2.00.04 (Nov 12 2008 10:51:08) and it's not showing all issued wireless or Wired IP addresses in DHCP Client List.
They all have IP addresses and connect to the internet through the router, but in the router administration page, they're not listing. The Windows devices all show but most of the Mac devices are not, nor is my XBox 360.
My reason for investigating this is because the router seems to keep losing the Mac devices and a router reboot fixes it, but it shouldn't have this problem because all the Windows devices just seem to work.
According to the support page I have the latest available (dated November 12, 2008 which really seems kinda old to me for a Wireless N router). Are there any plans for a new firmware offering for this modem or have you already deprecated it as "legacy equipment"?
View 1 Replies
View Related
Jul 21, 2012
I configure the virtual MAC address for a interface on ASA 5520, will enter the following command on the active unit:
failover mac address Inside 0012.3456.789a 0023.4567.89ab
The active MAC address is of the same as the Inside's burned-in MAC address of the active unit.Similarly, the standby MAC address is of the same as the Inside's burned-in MAC address of the standby unit.Do I get the effect of failover mac address command?
View 1 Replies
View Related
Oct 8, 2012
In setup for old RV042 (V1), when updating / adding Mac addresses, the table is always sorted by IP addresses. But in the new oneRV042 (V3) I have, even with latest firmware 4.2.1.02 the list is random, thereby increasing the chance of user entering DUPLICATE IP addr with diff Mac addr. That will result in conflict.If the firmware sorts the DHCP entries by ip addresses, user would be able to catch duplicate ip errors even if the system does not flag the errors. All Cisco smart engineers can you all get the dhcp entries SORT by ip addresses.
View 2 Replies
View Related
Aug 20, 2012
I'm planning to setup a network with more than 300 PCs. I know that using class C address is not enough to allocate number of IP addresses required. What I meant in the preceding sentence is that If I use this network address 192.168.1.0 (class C), it will allow only 256-2 = 254 IP addresses, What about other PCs in the network ?
View 3 Replies
View Related
Nov 15, 2012
I have various unknown Mac addresses on my network,detecting if they are normal/non harmful OR if I've been hacked! I've uploaded a picture of the addresses, the second to the last address is my router's.
View 1 Replies
View Related
Mar 22, 2011
I have various unknown Mac addresses on my network, I need to detect if they are normal/non harmful OR if I've been hacked! I've uploaded a picture of the addresses, the second to the last address is my router's.
View 14 Replies
View Related
Jul 11, 2012
i can't find my wireless network in the list. It shows me networks from my are but not my one. I know my one works and has no problem as my sister can use her laptop wirelessly
View 19 Replies
View Related
Jul 5, 2011
I've been "borrowing" a neighbor's wifi for the past 2 months. Everything was fine..a few hang ups here or there but other than that, no problem. The other night, my connection disconnected and i haven't been able to reconnect to the network for the past 24 hours.. The network is on the list of available networks. It's open, always has been. When i click it to connect, nothing happens. I've tried repairing the connection, turning off and on my radio signal
View 3 Replies
View Related
Sep 18, 2011
I have 192.168.2.1 and 10.10.0.1But i cant connect to 10.10.0.1 network from 192.168.2.1 network. What should I do to connect that both are same network I have a Linksys Router.
View 2 Replies
View Related
Dec 5, 2011
how do i assign IP addresses to 10 computers in a network?
View 3 Replies
View Related
May 28, 2012
i create a network topology ( i attached picture) and i don't know what exactly IP addresses should be assigned to routers and switches + there should be five VLAN's created and just one vlan (vlan 2) must see others vlans (for management purposes) and others vlans should not see each other. So i need that: 1) What IP addresses should be on routers and switches 2) How to create a 5 vlans, that they should not see each other, but one should see all, for example where i have to put "tagged" ports where "untagged" or "not member" ports etc.
View 1 Replies
View Related
May 23, 2012
I have a home network with a Netgear N600 as my main router. I have a wirelesss HP printer that accesses fine as does Iphones and Ipad. Then I have hard wires. Off of the main router I have 3 Netgear 5 port switches. 1 switch with a line to bedroom tv and a line to family room tv. 1 Switch at family room TV which goes to Blu Ray, Direct Tv, and Xbox360. 1 switch at bedroom for Blu Ray and Direct TV. Believe it or not, this all worked. I tried to hook up a ZmodoH264 security system (the ones with four cameras, and a separate hard drive and monitor for viewing). I used one of the 4 inputs on the main Netgear router for this, and it seemed to be recognized. But, I can't access the security system mobilly, AND all my network addresses seem to have been screwed as Directv isn't working (Whole Home) and the printer stopped being recognized. However, Blu Rays are still fine. Is there a way with ipconfig to list all of my hard wired nodes? I assume wireless dont show up in a list.
View 4 Replies
View Related
May 28, 2012
i create a network topology ( i attached picture) and i don't know what exactly IP addresses should be assigned to routers and switches + there should be five VLAN's created and just one vlan (vlan 2) must see others vlans (for management purposes) and others vlans should not see each other. So i need that: 1) What IP addresses should be on routers and switches 2) How to create a 5 vlans, that they should not see each other, but one should see all, for example where i have to put "tagged" ports where "untagged" or "not member" ports etc.
View 4 Replies
View Related
Jul 10, 2012
My church has a AT&T wired modem and a Netgear Wireless router. Pastors office is on other side of church and he is losing signal occassionally. His network is showing two SSID addressed cgcg cgcg2
View 4 Replies
View Related
Mar 5, 2011
In my wireless table of who is connected to the wireless network there are 3 different mac addresses displaying when there is only two computers in the house(its not an outsider, it only shows when the other PC turns on), 2 of them have the same computer name but are connected at different IP addresses(192.168.1.101,192.168.1.102). Side Note:[The 2 PCs in the house were bought at the same time and the mac addresses are similar, but the third is different] Now that i have installed ubuntu i can really see what's going on with my ports, i notice that the mac address, that is not similar to my PC and the 'other pc', is poking around at my ports whenever the 'other PC' is turned on.
View 2 Replies
View Related
Jan 19, 2013
I have used all the spots on the form to filter mac addresses. Is there some way to add more? I have a lot of friends that come over from time to time. I also have plenty of my own wireless devices.I like using the mac address filter so not using it is not an option. Hopefully there is a way to add more, instead of being limited to a predetermined amount.
View 3 Replies
View Related
Jan 17, 2011
I recently added several devices to my wireless-g network: Xbox 360, an HTC Smart phone, and an old laptop my buddy gave me (in addition to the 2 desktops that were already on the network). Since doing this, I've had occasional buffering problems when streaming music or video, even when I'm only using 1 of the devices. I suspect that the Xbox (or maybe phone) is downloading updates in the background, even when it's turned off, and that is consuming bandwidth. Is there any way I can see a list of devices that are connected to the network and maybe even the amount of data being transmitted to/from each so I can find the culprit. when I play online, it says that my NAT settings are not open and that this makes it take longer to connect to other players. What are the risks involved in loosening the NAT restrictions?
View 1 Replies
View Related
Jan 24, 2012
II tried to make a wep password. and when i made one, i went on my laptop to try to find my network but my network name was completely gone from the list of available wifi networks i can connect to.
View 2 Replies
View Related
Feb 1, 2012
I've setup my VPN on the cisco ASA 5505 which works perfectly, users from outside can access my internal LAN. Now what i want, Is to create another VPN Tunnel group with another set of IP in which i want to allow them access to one server inside our LAN. See below details of network. [code]
View 1 Replies
View Related
Nov 10, 2011
How can i use a router to extend the ip addresses of a separate network? I have been given a subnet mask of 255.255.255.248 which has given me 6 ip addresses to access the internet. How can i use a router to allocate extra ip addresses and route them to the internet ?
View 1 Replies
View Related
Jan 31, 2011
When I click on to my wireless network list nothing shows up, but I use my work pc and about 20 networks show up. What is going on with my lap top.
View 1 Replies
View Related
Mar 1, 2012
I recently change routers to a Linksys E3000 wireless router from a Uverese 2wire residential gateway and all worked well for a short time nothing changed however when I go to view network devices from Win7,Vista or XP computers the network devices are no longer there. when I shut down and reboot the router and switches I still cannot see these devices, however when I hook up my old 2wire router I see my devices again. Even when I reconnect to the E3000 all the devices can be viewed for a few hours. Changing routers resets something but maybe overloads the linksys E3000 after a few hours? maybe this E3000 is just defective?
When I view a network map in Network & Internet all the devices appear in the map The configuration is Linksys E3000 router with two (2) 8 port Trendnet gigabyte switches and One (1) 8 port Trendnet Poe 10/100 switch. They are chained router to 8 port gig to 8 port gig to 8 port Poe 10/100. Prior to this I had the router to each switch separately - - this does not seem to matter works the same either way
Devices attached - Network printer,XP desktop, Vista Desktop, NAS, WDTVlive media player, Roku, Home automation controller, IP touch screen for the automation, security DVR (wireless devices are all ok Win7 laptop, Vista laptop, Ipad)seldom are more than 3 devices being used at one time light traffic.)
View 2 Replies
View Related
Dec 13, 2011
I have new DIR-615 D-link router. Since we installed it the network has disappeared randomly off the available networks list, and when I try and open Google Chrome it says there's DNS error. Troubleshooting through windows networks doesn't work because it can't find any problems since my network doesn't even show up on the list. We've even done a factory reset and the problem persists, and it does this about once a day. Resetting the router temporarily fixes the problem. This problem is happening on all 3 laptops in our home, two of which run windows 7 and one which runs XP.
View 1 Replies
View Related
Jun 16, 2012
I have a LAN with about 200 computers (192.168.10.0/24) with a DHCP Server on Windows server 2003.The problem is that my company have acquired 100 others computers that I have connected on this network.Some computer does not get IP address from the DHCP server. When I investigated the log of the DHCP server, I realized that the DHCP server was out of addresses.
View 2 Replies
View Related
Jan 10, 2012
How can I find out the ip addresses of contacts in social networks
View 2 Replies
View Related
Nov 9, 2012
Is there any solution for automatic switching between wired and wireless network connection?
In my work we have two option for connection to network. Wired for working but with blocked pages like youtube and other streaming media. And wireless for visitors which haven't blocked any pages but I can't do my work on it. Can I by connected to both and some utility will doing switching between them? I want to use streaming and be connected to wired network which has blocked streaming.
View 1 Replies
View Related
Feb 25, 2012
I can see what MAC addresses have a wireless session and I've used MAC Filtering to stop some MAC addresses from using the network at certain times, but they are still getting through to the internet. I don't know if they were to clone their MAC address as to whether this would show up with the cloned address in active sessions list. How I can stop some users from getting through at certain times? Any utility I can use on my Mac (Mac OS X 10.6. to show which computers/MAC addresses are on the network?
View 5 Replies
View Related
May 26, 2011
I have set up a private domain network at home. I have a domain controller, a DNS server, and a DHCP server all running on one Windows 2003 Server machine. I have about 10 other machines around the house, getting their IP addresses from this DHCP server.
I have a Netgear WNDR3700 router.
I am about to get 5 public IP addresses from my ISP, and I would like to make some of these machines publicly accessible (while still accessible from the other machines in the network).
I found this link that says on my web server (one of the public machines), that I should use a second NIC and set that up to connect to my router (and get a private IP address from my DHCP server).
View 1 Replies
View Related
Mar 3, 2013
i don't know how I have done this but I have managed to connect my partners laptop to my network list on my new Toshiba laptop (don't know if make or modal matters) this seemed to have appeared whilst uploading and fetching photo's with skydrive,how do I get him off my network list???
View 1 Replies
View Related
