I have a LAN with about 200 computers (192.168.10.0/24) with a DHCP Server on Windows server 2003.The problem is that my company have acquired 100 others computers that I have connected on this network.Some computer does not get IP address from the DHCP server. When I investigated the log of the DHCP server, I realized that the DHCP server was out of addresses.
View 2 Replies
Haveing issue with DHCP server handing out IP addresses to client connected to VLAN5 interface.ISP Router>Firewall -(WatchGuard Drop-in mode) I have several 3750 switches and one acting as a L3 switch. The L3 is configured as follow: [code]
If I connect a laptop to int fa1/0/10 I DO NOT get an IP address from the 10.100.0.8 scope. If I connect to another interface within the VLAN 1, I get an address from the 10.100.0.0 range.
I've created a tonne of dhcp scopes on my routers before never had any issues, however this one will not hand out any addresses at all, i even give the router a reload to see if any magic happened but nothing, ive ended having to put a temp server in with just dhcp installed until i get the router diong what it should my config below, its something simple i havent seen, as ive compared it to plenty of my working DHCP configs and seen nothing.
View 11 Replies View RelatedI have a Belkin model F9K1102 router supplying WAN/LAN connection to three PCs and 2 laptops. Two of the PCs are hardwired with the remainder PC and laptops are wireless. I'm using the default router IP of 192.168.2.1 and my ISP is Charter Cable (if that's of significance). The router is picking up all the dynamic IP information from my ISP and internal DHCP is enabled. Here's the issue though - when I connect a PC, laptop or iTouch (wired or wireless) with obtain IP settings automatically enabled the IP address it receives an IP address on a different subnet ie, 192.168.3.x and thus won't have WAN/LAN connection. I have tried to set the router IP to 192.168.3.1 and set the scope in the .3 subnet but the IP obtained by the device is .4! This makes no sense to me at all. The router is on the latest firmware (according to Belkin) and there doesn't seem to be any other update I can find. I have also tried another Belkin router (older model: F5D8236) and it does the same thing.
I'm not sure if this is related but I upgraded my service with Charter to a 18MB connection and a D3.0 Ubee cable modem - this issue seem to have began after this upgrade but I don't see how that would have any bearing on what is happening on my LAN IP scope and Charter tech support is pretty useless. My workaround is that I've static assigned an IP for each device in the same subnet as the router but it would be nice for the DHCP to function correctly.
Had a problem with a 3750 this morning not handing out DHCP addresses. The following is a sanitized config of what the switch is using. [code] The IOS installed on the switch is c3750-ipbasek9-mz.122-55.SE1.bin. What got my attention was that the sh ip dhcp pool PC showed 180 addresses being excluded. In doing the math from the dhcp excluded addresses, only 64 should be excluded.
My next step was to remove the second dhcp excluded-address line above. Doing a clear ip dhcp binding * started letting the DHCP service hand out addresses but the sh ip dhcp pool PC stil showed 180 addresses excluded.
It finally took removing the dhcp pool and putting it back in to drop the number of excluded addresses down to a value that matches the first excluded-address line. Didnt see a dhcp bug in the bug database that would explain this.
I tried re-entering the second excluded-address line from above and saw the number of excluded addresses rise as expected. When I negated the line, the number of excluded addresses dropped back to its previous value.
I have a DHCP server for a subnet that has only lightweight WAP's in it. The DHCP server is running on the gateway for this subnet which is a 3750X 2 switch stack running 12.2(53r)se2.I have the following configured:
ip dhcp excluded-address 10.1.10.161 10.1.10.162
ip dhcp pool DHCP-VL20
network 10.1.10.160 255.255.255.224
domain-name mydomain.net
dns-server 10.11.11.30 10.11.11.40
default-router 10.1.10.161
ease 3
The server hands out up to 18 IP addresses and no more, with 20 devices on the subnet. Scanning the subnet with a 3rd party network management system I see the following IP's never get handed out or used:
10.1.10.161 - 162 (manually excluded)
10.1.10.167 - 168
10.1.10.171 - 176
10.1.10.178
and of course 2 IP's I have manually excluded, 11 IP's in all that wont get handed out. It should only be 2 that don't get handed out. I've double and triple checked the exclusion and thats the only one. so I run a 'sh ip dhcp pool' and see this:
Pool DHCP-VL20 :
Utilization mark (high/low) : 100 / 0
Subnet size (first/next) : 0 / 0
Total addresses : 30
[code]....
[edit]I should also mention that "sh ip dhcp bind" does not show these randomly excluded IP's in use. They also do not show up in any arp table I can find.I have looked all over the config and I cant find where these extra 9 addresses are being excluded. how to free up these 9 seemingly random exclusions? Haven't issued a reload and I haven't deleted and rebuilt the DHCP server yet, production network.
Have a client wanting to hand out public ip addresses to all clients from a PFSense Firewall terminating the internet connection.
How do I allow the Cisco Switches currently in place, configured with private ip addresses in the 10.10.x.x ranges and Vlans, where the main 3550 layer 3 has defined dhcp scopes for each vlan, to relay dhcp requests from all vlans to the PFSense firewall?
I assume I would take off the currently defined dhcp scopes for the vlans and configure each vlan/switch with the ip helper address and specify the PFSense firewall and that Nat would have to be disabled onthe firewall?
We have a 3750 running IOS ver 12.2 (44) SE, it has performed great and we have never had a problem with it. However we have noticed that when we had an outage some of our Wireless APs didn't come up as they get DHCP from the 3750. The DHCP scope said IP was depleted although there were IPs to give. We had to delete and recreate the DHCP Pool. However two days later we got the same problem and then had to do the same thing over again.
View 8 Replies View RelatedI imagine I can use the framed-ip-address attribute to assign ip-addresses but there seem to be support for static ip addresses only?A bit of a drag when we're talking 200+ nodes.
View 1 Replies View RelatedWe have a Cisco 5505 ASA fireawll at a remote site. I can get the firewall to issue the IP addresses to the pc's, Is there a way for the pc's to get their IP addresses directly from our DHCP server?
View 3 Replies View RelatedI used to use a CentOS self-made server for intranet for my little office, but I bouth few days ago a Cisco 861 router to replace the linux box.
1. I have 2 public IP classes from my ISP. 1 class is limitted to 80mbit upload, the other to 30mbit upload. So I need some sort of DNAT to be able to know exactly which intranet computer uses big internet and which one limitted internet.
2. I need DHCP server and with static IP addresses (one computer must always have the same IP address, etc).. i have my needs for this.
3. Also I need external access to some servers inside (web, ftp, etc) [code]
So far so good, all looks simple and I can achieve this in 2 hours on a centos linux box (correct routes, ip forwarding enabled and few iptables rules for NAT/SNAT/DNAT).
But on this brand new Centos router well, i'm not even successful in pinging the outside world, nor the inside world I'm tired of reading the forums, the documentation..i want (at first) a simple scenario: vlan+dhcp, fa4 with 1 public ip address and ACCESS to the real world. I wasn't able to achieve not even that much. [code]
I currently have DCHP server set up on my new 1141N. Everything works great, but I wanted to know if it were possible to make the DHCP server only hand out ip addresses on the wireless connection? Currently the AP is giving out ip addresses from the pool to wired and wireless pc's.
View 3 Replies View RelatedSetting up a stand-alone WDS/PXE server.Current we have helper addresses setup to forward the DHCP requests from the different VLAN's to the DHCP server. The WDS/PXE server we are setting up is on its server. How do we craft the helper addresses so DHCP requests go to the proper server hosting DHCP and PXE requests go the WDS server?
Everything I seen on Microsoft Technet, lists using Helper Address as the recommended way, but assume both services are on the same server. Our helper address is as follows on each VLAN interface in router: ip helper-address X.X.X..This is a Cisco 3750.
I upgraded my SG500 switch firmware to 1.3.0.59, since there is a new functionality DHCP server v.4 well I must say I came accross the issue I cannot solve. DHCP server assign dynamic address - no hassles. troubles start with static IP hosts.I defined a couple of hosts with static address within the correct subnet. I tried with hardware address and client identifiers. no luck. my switch does not assign the IP address I assigned to the suitable mac address. to define it I use both CLI & Web.
ip dhcp pool host HP-Elliteaddress 10.10.11.7 255.255.255.0 client-identifier 01:d8:d3:85:cf:09:72client-name HP-Ellitedefault-router 10.10.11.1exit
ip dhcp pool host VAIO-Zaddress 10.10.14.108 255.255.255.0 hardware-address 54:53:ed:1c:a1:46
default-router 10.10.14.1exit
Is it possible to assign IP addresses to remote site WIFI users from local DHCP server and forward all other traffic to 2504 WLC?
[WIFI Users] >--------<AP (DHCP server) >------ VPN ---------< WLC
Why is it that the dhcp on my router is no longer able to give out ips or rather it assign them as for as it concerned as it will list say 199.170.0.102 but the device will have none or make up one for it's self and never get the ip that the routers dhcp gave it this happens on all devices. I know power cycling will fix it temporally but usually it will start doing it again in a few hours also I know that I can use a static ip this was my way around this problem but I have one device that won't use nothing but dhcp a printer. I had an old linksys router that did this and I figured it's old it's slow time for a new one after a few months it started, some computers are on the fringe of being able to get a signal but are still fair also even with static ips they sometime stop connecting and we have to disable the connection then reconnect to fix it the router is a dlink 615 dual band set to only G/B because 1 most devices only g 2 the one computer that has a wireless n is 70 ft away and works better with g.
View 13 Replies View RelatedWhat tool can I use to accurately pin point a rogue dhcp server in our network?
View 1 Replies View RelatedSo have a wireless guest network on an N600 router. Here is my setup:
pf sense -> untangle -> switch <- N600
the N600 is just an access point and does no DHCP. The primary wireless network gets IP no problem but the guests are not getting an IP. I'm assuming the N600 has no way of issuing an IP on the guest network. how to set a DHCP server on the guest network and have a static route to the pfsense firewall from that network.
I've just installed a 2106 Controller at a remote site. The Controller is seen by the WCS at the main site so, connectivity is good and I'm able to login from the main site. I've configured the DHCP server which is at the Main site on the AP manager interface and the Manager interface and on the WLAN of the new controller but, APs are not getting addresses.
View 6 Replies View RelatedWe have been using a dhcp and tftp server to automatically configure branch WAN routers such as 1751's and 1841's for years but, have recently purchased a 1921 and 1941 as possible next generation replacements. The problem is when the 1900 series power up instead of getting a dhcp address directions to the tftp server it boots up and asks for the user name to be immediately changed or you will be "locked out". Any workaround to this so that I can again go back to download my common configuration? Or any other way of automatically configuring the newer version ios? Doing extra steps for 500 WAN branch routers is time consuming. Doing configurations without automation for that many is moving in the wrong direction.
View 1 Replies View RelatedI just moved to Auckland, NZ from the USA to go to school at the university here, and am having a problem connecting to the internet in the university residence hall in which I am living.Wifi is not available in the residence halls, so we need to use an Ethernet cable. When I plug in my computer, the network adapter icon says Identifying for a while then settles on Unidentified Network with no internet access, the IP is 169.x.x.x.When I try to release and renew the IP, it says unable to contact your DHCP server, request has timed out".I've tried multiple Ethernet cables, both brand new.I tried connecting to a port in a friend's room in the same building, and even in a classroom on campus, and both had the same result.Naturally after all that I assumed my NIC somehow died overnight while I traveled here, so I went to a computer repair shop expecting to have some hardware replaced, but we plugged it in there and it worked immediately so they weren't sure what to tell me.
I've gone through pages of old threads at this forum and others like it, trying solutions but having no luck.I've power cycled my computer, obviously I can't power cycle the whole network as it's for 200 people, but the IT people here have tried resetting it for me on their end as best they can. [code]
i have a cascading network in my house of 2 linksys routers, I left the DHCP server activated on both of them and it seems to work fine, whats the point of turning it off?
View 2 Replies View RelatedHow can i configure DHCP to use two different range of IP addresses. One range will be for example 192.168.0.* and the other range will be 192.168.1.* When the first range of ip is full the DHCP automatically assign IP addresses from the second range.
View 9 Replies View RelatedI have upgraded a C3750G-12S-E to c3750-ipserviceslmk9-tar.122-55.SE5This switch is a distribution layer switch for one of my remote sites. it contains an ip helper-address on the site vlan's SVI.DHCP relay is no longer functioning for client PCs. Static address assignment allows full network functionality. I enabled debug ip dhcp server packet. [code] Actually I am betting you upgraded your IOS from something before 12.2(50)SE to 12.2(50)SE or later. We added enhancement CSCso19800 which will validate DHCP options when we are a relay agent.
View 1 Replies View RelatedInitially there were 3 SSIDs configured but all of them were assigned a single interface and this interface was configured with the controller management IP address as DHCP server so that the WLC could assign IP addresses to wireless clients, guns and printers etc.
Issue: As part of PCI initiative, we decided to segment the traffic in multiple subnets based on type of wireless clients; so now there are 3 interfaces configured and each SSID is assigned a specific dynamic interface and each interface is configured to use the controller management IP address as DHCP server.
There are 3 scopes configured for each of the dynamic interfaces/SSIDs and DHCP proxy is enabled but wirelss clients are still being allocated IP addresses from the original DHCP scope that was associated with the dynamic interface originally assigned to all 3 SSIDs.
I verified the following:
1. Each SSID is assigned a different dynamic interface (Users, Voice and Handhelds)
2. Each dynamic interface is configured to use controllers management IP address as DHCP server
3. DHCP scopes configured with correct network information for each dynamic interface and enabled
I recently upgraded a clients WLC and they keep saying they are unable to get an IP address from the DHCP server. It's a simple, flat network and here is what the logs are showing.
*apfReceiveTask: Apr 11 13:37:25.477: %SIM-3-DHCP_SERVER_NO_REPLY: sim_interface.c:1039 Failed to get DHCP response on interface 'management'. Marking interface dirty.
*apfReceiveTask: Apr 11 13:37:17.278: %SIM-3-DHCP_SERVER_NO_REPLY: sim_interface.c:1039 Failed to get DHCP response on interface 'management'. Marking interface dirty.
*apfReceiveTask: Apr 11 13:37:05.880: %SIM-3-DHCP_SERVER_NO_REPLY: sim_interface.c:1039 Failed to get DHCP response on interface 'management'. Marking interface dirty.
*apfReceiveTask: Apr 11 13:13:47.397: %SIM-3-DHCP_SERVER_NO_REPLY: sim_interface.c:1039 Failed to get DHCP response on interface 'management'. Marking interface dirty.
[code]....
I have a LAP1142N that is connected to a 3560 nonPoE switch (using compatible power injector) that will not associate to the controller I have set-up. The wireless is existing and I have about 11 other APs connected to the controller with no issues. The AP will pull an IP address from DHCP running on the primary controller. The AP pulls a new IP address in roughly a minute. I set the pool to be 3 IP addresses and set a contant ping to each, there is about 1 request time out before the next IP address starts pinging. I went to the controller and pulled the following message error from the log.
*Feb 13 14:24:58.614: %LWAPP-3-HDR_ENCAP_ERR: spam_lrad.c:4216 Unable to encapsulate LWAPP header for discovery response; AP (APs MAC address)
*Feb 13 14:24:58.614: %APF-3-PDU_ENCAP_FAILED: apf_net.c:771 Failed to encapsulate a PDU for transmission to station00:00:00:00:00:00. Destination IP address not set in L3 mode.
I have tried a different cable, connecting to a PoE switch, different controller, larger DHCP range, hosting DHCP on the distribution switch, I am awaiting console access to the AP since this is remote work. The controller is running Software Version 5.1.151.0. Thoughts?
console inventory output from GUI
Model No. AIR-WLC4402-25-K9
Burned-in MAC Address XXXXXXXXXX
Maximum number of APs supported 25
Gig Ethernet/Fiber Card Absent
[Code] ....
Have a WLC 5508 running 7.0.230 with internal DHCP server. Timeout is 3600 seconds. The IP addresses never seem to be released. The controller will show 70 clients but 254 addresses will be assigned.
View 2 Replies View RelatedI currently have a the following configuration and am unable to get more than 2 DHCP addresses for the devices connected to the Cisco new SG 100-16 Switch.The AP have no trouble handing out DHCP to the wireless clients, but we are unable to get the SG 100-16 to be able to do the same thing to wired clients. It is currently connected to the 2960-8 in port 1. We can get 2 devices connected without a problem, but the 3rd machine and beyond do not work. Also, setting up a static IP does not work. Using a static will not even allow us to ping or tracer back to any devices beyond the SG 100-16.
View 7 Replies View RelatedNetgear DG834 allocates IP Addresses using DHCP to 5 computers and 2 tills, the tills addresses and one computer IP addreess are reserved and fixed, so that data can be downloaded from the tills to this computer. However I had to re-format the computer and the Router now allocates a new IP address to it, which the tills cannot recognise, so I cannot download the data from the tills to the computer. Is it possible to change the newly allocated Computer IP address in the Router back to the old one.
View 9 Replies View RelatedI have a wireless access point, I want to be able to hand out addresses via the Cisco router through DHCP on the interface eth0/1. The wireless users that get an IP I want then route out the eth0/0 interface to my statically assigned default gateway. Right now Im not concerned with setting up security measures once this works I'll go back in and add that. Here is my running-config. Right now nothing from the 10.0.0.0 is being routed out to the internet.
View 6 Replies View RelatedA small network and uses the Linksys Router BEFSR81 as dhcp.the default Number of addresses is 50 and starts 10.0.0.100 to 10.0.0.149.A new Cisco IP Phone just introduced requires ip addresses and have noticed running out of addreses.Can I increase the number to 120 so that the address range would start from 10.0.0.100 to 10.0.0.219, also, I have a VPN device which automatically configures itself for 10.0.0.199 address and this is /24 network configuration.
View 1 Replies View RelatedStarted this morning woke up checked my phone no wifi hmm weird checked my hp tpuchsmart connected but jo internet access checked my router(netgear wireless N 300) made sure my modem and all wires are connectedNext went to my router ip 192.168.1.1 after reading some forrums i thought maybe if i changed the ip or sum i would have worked i know dumb though.. any way i believe i disabled my dhcp.. and one of the ip ad on the same page to 192.168.1.3 thats when it got worst i tried ipconfig/release saysNo operation can be performed on bluetooth network connection 2 while it has media disconnected.No operation can be performed on local area connection while it has its media disconnected(Its a wireless connection from my touchsmart to my router) I have tried goin back to the routers page but i can no longer find itI have also tried ipconfig/renew but i get this...No operation can be performed on bluetooth network connection 2 while it has its media disconnectdAn error occured while renewing interface wireless network connection : unable to contact your dhcp server. Request has timed out.No opration can be performed on local area connection while it has its media disconnected
View 3 Replies View Related
